RFQ_Att_4_-_SOW_Encl_1_-_SEAGUARD_Paint_Data.pdf

SEAGUARD®

HEAVY METAL FREE

ABLATIVE ANTIFOULANT

RED N51R301

BLACK N51B301

6/09

SeaGuard Marine & Specialty Coatings

Adhesion Method: ASTM D4541-02 Result: 900 psi

Four year Fouling Rating:

Method: ASTM D3623, Total immersion, Seawater, Ponce Inlet, FL Result: Rating 10 for general performance, Mollusks, Bryozoans, Amphipoda; Trace (<1% coverage) Barnacles, Anvelids, Hydroids, Algea

Biocides

Are non-persistent in the environment• Low solvability in water• Controls fouling organisms without the environmental impact • to water quality or sediment associated with traditional metal based antifoulants Product controls a broad spectrum of fouling• Service life of the coating is proportional to fi lm thickness• Three hour hydrolytic half-life in seawater @ 77°F• Can be specifi ed for dry-dock intervals up to 5 yrs•

Finish: Matte

Color: Red and Black

Volume Solids: 63% ± 2%

Weight Solids: 79% ± 2%

VOC (EPA Method 24): <340 g/L; 2.8 lb/gal

Recommended Spreading Rate per coat:

Wet mils: 5.0 - 10.0 Dry mils: 3.0 - 6.0* Coverage: 170 - 340 sq ft/gal approximate

Drying Schedule @ 4.0 mils wet @ 50% RH:

@40°F @ 77°F @100°F To recoat: 72 hrs 16 hrs 8 hrs To undock: 6 days 24 hrs 12 hrs Drying time is temperature, humidity and fi lm thickness depen-dent.

Shelf Life: 24 months, unopened Store indoors at 40°F to 100°F.

Flash Point: 102°F PMCC

Reducer/Clean Up: VM&P Naptha, R1K3 or R2K5

* See Performance Tips

PRODUCT DESCRIPTION

PRODUCT CHARACTERISTICS

RECOMMENDED USES

PERFORMANCE CHARACTERISTICS

PRODUCT INFORMATION SHEET

SeaGuard Heavy Metal Free Antifoulant is a solvent based, copper and tin free ablative antifoulant coating that deters soft and hard fouling.

• Contains unique metal free organic biocide technology to comply with IMO ban on coatings containing TBT

• Biocides are non-persistent in the environment

• Low VOC to comply with environmental regulations

• EPA Registration Number: 577-570

• Qualifi ed to MIL-PRF-24647D, Type I, Class 1 and 2, Grade

A and B, Application 1

Where a no copper discharge level antifoulant is required• Where a tin free, copper free, heavy metal free antifoulant • is required Where a low weight antifoulant is required. This product • weighs approximately 2/3 that of traditional copper based antifoulants Can be used over prepared existing antifouling systems• Acceptable for use on aluminum hulls• Service life of the coating is proportional to fi lm thickness•

Marine & Specialty 9.17 continued on back

9.17

The statements made herein are based on our research and/or the research of others believed to be accurate.

No guarantee of their accuracy is made however, and such statements may be changed without notice.

www.sherwin-williams.com

SeaGuard Marine & Specialty Coatings

SEAGUARD®

HEAVY METAL FREE

ABLATIVE ANTIFOULANT

RED N51R301

BLACK N51B301

Steel:

2 cts. SeaGuard 5000 HS @ 4.0 - 8.0 mils dft/ct 2-3 cts. SeaGuard Heavy Metal Free AF @ 3.0 - 6.0 mils dft/ct*

Other acceptable primers:

SeaGuard 6000• Sher-Plate 360•

Aluminum:

1ct SeaGuard MP @ 3.0 - 4.0 mils dft 1 ct SeaGuard 5000 HS @ 4.0 - 8.0 mils dft 2-3 cts. SeaGuard Heavy Metal Free AF @ 3.0 - 6.0 mils dft/ct*

*The SeaGuard Heavy Metal Free AF must be applied over the epoxy primer, while the epoxy is still slightly tacky.

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure good adhesion.

Refer to product Application Bulletin for detailed surface prepa-ration information.

Minimum recommended surface preparation:

Iron & Steel: SSPC-SP10, 2 mil profi le

Temperature: 40°F minimum, 100°F maximum (air, surface, and material) At least 5°F above dew point

Relative humidity: 85% maximum

Refer to product Application Bulletin for detailed application information.

The systems listed above are representative of the product's use. Other systems may be appropriate.

Packaging: 1 and 5 gallon containers

Weight per gallon: 12.5 ± 0.5 lb

PRODUCT INFORMATION SHEET

RECOMMENDED SYSTEMS SURFACE PREPARATION

TINTING

APPLICATION CONDITIONS

ORDERING INFORMATION

Refer to the MSDS sheet before use.

Published technical data and instructions are subject to change without notice. Contact your Sherwin-Williams representative for additional technical data and instructions.

SAFETY PRECAUTIONS

Do not tint.

9.17

SEAGUARD®

HEAVY METAL FREE

ABLATIVE ANTIFOULANT

RED N51R301

BLACK N51B301

6/09

SeaGuard Marine & Specialty Coatings

The following is a guide. Changes in pressures and tip sizes may be needed for proper spray characteristics. Always purge spray equipment before use with listed reducer. Any reduction must be compatible with the existing environmental and ap-plication conditions.

Reducer/Clean Up ...........VM&P Naptha, R1K3 or R2K5

Airless Spray Unit.................................Graco 45:1 Pressure.........................3200 psi minimum Hose...............................3/8" ID Tip ...................................019" - .021" Filter ...............................30 mesh Reduction .......................As needed up to 5% by volume

Conventional Spray Gun ................................Binks 95 Fluid Nozzle Fluid Hose ......................1/2" ID, 50 ft maximum Air Nozzle.......................63 PB Air Hose .........................1/2" ID, 50 ft maximum Atomization Pressure .....25 psi Fluid Pressure ................10-20 psi Reduction .......................As needed up to 5% by volume

Brush Brush..............................Natural Bristle Reduction .......................As needed up to 5% by volume

Roller Cover .............................3/8" woven with phenolic core Reduction .......................As needed up to 5% by volume

If specifi c application equipment is listed above, equivalent equipment may be substituted.

APPLICATION BULLETIN

SURFACE PREPARATION APPLICATION CONDITIONS

APPLICATION EQUIPMENT

Temperature: 40°F minimum, 100°F maximum (air, surface, and material) At least 5°F above dew point

Relative humidity: 85% maximum

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Iron & Steel Minimum surface preparation is Near White Metal Blast per SSPC-SP10. Remove all oil and grease from surface by Solvent Cleaning per SSPC-SP1. Blast clean all surfaces using a sharp, angular abrasive for optimum surface profi le (2 mils). Remove all weld spatter and round all sharp edges by grinding. For surfaces prepared per SSPC-SP12/NACE No.5 , all surfaces to be coated shall be cleaned in accordance with WJ-2. Pre-existing profi le should be approximately 2 mils. Prime any bare steel within 8 hours or before fl ash rusting occurs.

Previously Painted Antifouling Surfaces Remove possible oil, grease, etc. with suitable detergent. Rinse using high pressure, fresh water cleaning, which will also remove any weak, outer layer of leached antifouling. Allow the surface to dry before over coating. Whether or not to use a sealer coat over an existing antifouling depends on the type and condition of existing antifouling coatings.

Marine & Specialty 9.17A continued on back

9.17A

The statements made herein are based on our research and/or the research of others believed to be accurate.

No guarantee of their accuracy is made however, and such statements may be changed without notice.

www.sherwin-williams.com

SeaGuard Marine & Specialty Coatings

SEAGUARD®

HEAVY METAL FREE

ABLATIVE ANTIFOULANT

RED N51R301

BLACK N51B301

APPLICATION BULLETIN

APPLICATION PROCEDURES

SAFETY PRECAUTIONSCLEAN UP INSTRUCTIONS

Clean spills and spatters immediately with VM&P Naptha, R1K3 or R2K5. Clean tools immediately after use with VM&P Naptha, R1K3 or R2K5. Follow manufacturer's safety recommendations when using any solvent.

PERFORMANCE TIPS

Refer to the MSDS sheet before use.

Published technical data and instructions are subject to change without notice. Contact your Sherwin-Williams representative for additional technical data and instructions.

Surface preparation must be completed as indicated.

Mixing Instructions: Mix paint thoroughly with power agitation prior to use.

Apply paint to the recommended fi lm thickness and spreading rate as indicated below:

Recommended Spreading Rate per coat:

Wet mils: 5.0 - 10.0 Dry mils: 3.0 - 6.0* Coverage: 170 - 340 sq ft/gal approximate

Drying Schedule @ 4.0 mils wet @ 50% RH:

@40°F @ 77°F @100°F To recoat: 72 hrs 16 hrs 8 hrs To undock: 6 days 24 hrs 12 hrs Drying time is temperature, humidity and fi lm thickness depen-dent.

Shelf Life: 24 months, unopened Store indoors at 40°F to 100°F.

Application of coating above maximum or below minimum recommended spreading rate may adversely affect coating performance.

When using spray application, use a 50% overlap with each pass of the gun to avoid holidays, bare areas, and pinholes. If necessary, cross spray at a right angle

Spreading rates are calculated on volume solids and do not in-clude an application loss factor due to surface profi le, roughness or porosity of the surface, skill and technique of the applicator, method of application, various surface irregularities, material lost during mixing, spillage, overthinning, climatic conditions, and excessive fi lm build.

In order to avoid blockage of spray equipment, clean equipment before use or before periods of extended downtime with Xylene (R2K4).

Excessive reduction of materials can affect fi lm build, appear-ance, and performance.

When applying over a recommended epoxy primer, apply within 2 to 4 hours @ 77°F and 50% RH. The epoxy should be over-coated when it is tacky, but not hard.

Undocking:

Minimum undocking time depends on number of coats applied, fi lm thickness, and the prevailing temperature.

Maximum undocking time depends on the exposure conditions, degree of air pollutions, etc. The most important factor is to carry out a thorough high pressure fresh water cleaning after prolonged exposure. Out fi tting of up to 6 months followed by such clean-ing normally presents no problem. Longer outfi tting periods to be evaluated from case to case. The recommended maximum undocking interval relates to vertical bottom only. Flat bottom, which has not be exposed to direct sunlight, will for all normal practical building schedules have a no-maximum value.

* Dry fi lm thickness is based on the ships sailing, speed, activity level, dry dock interval, and trading patterns.

*The SeaGuard Heavy Metal Free AF must be applied over the epoxy primer, while the epoxy is still slightly tacky.

Refer to Product Information sheet for additional performance characteristics and properties.

9.17A