Test Procedure DI-NDTI-80603.pdf

DI-NDTI-80603 ND m 7 7 7 7 7 8 7 b00L762 2 m

10.1 Format Requirements. The test procedure shall be in the con-tractor's format on 8 1/2 x 11 inch paper. It shall be bound in such a manner that pages may be removed or inserted without damage or mutilation.

10.2 Content requirements. The test procedure shall contain the following:

10.2.1 Front matter.

I

DATA ITEM DESCRIPTION I Form Approved OMB NO. 0704-01a8

I

. TITLE 2. IDENTIFICATION NUMBER

TEST PROCEDURE I DI-NDTI- 80603

. DESCRIPTION I PURPOSE

3.1 The test procedure identifies the step-by-step testing operations to be performed on items under going developmental, qualification, or acceptance testing. It identifies items to be tested, the test equipment and support required, the test conditions to be imposed, the parameters to be measured, and the pass/fail criteria against which the test results

(continued on paqe 2) ). APPROVAL DATE I 5. OFFICE OF PRIMARY RESPONSIBILITY (OPR) 6a. DTlC APPLICABLE 6b. GlDEP APPLICABLE

(YYMMDD)

G4428

O. PREPARATION INSTRUCTIONS

10.2.1.1 Cover and title rsaqe. The following information shall be included on the coverband title page:

a. Date of issue.

b. Revision date (If applicable).

c. Procedure document identification number.

d. Contract number.

e. Contractor's name and address.

f. Type of procedure, including purpose (e.g.! first article

g. Identification of the system, subsystem, or equipment to

h. Security classification (if applicable) test, developmental evaluation, qualificatlon, environ-mental (specify), acceptance, or other).

be tested.

(continued on page 2) I l . DISTRIBUTION STATEMENT

DISTRIBUTION STATEMENT A: Approved for public .release, distribution is unlimited.

ID Form 1664, MAR 87 lun 86. edition may be used until exhausted. Page 1 of." Pages 491072

Document provided by IHS Licensee=NADEP/5918326100, User=, 02/11/2003 06:20:23 MST Questions or comments about this message: please call the Document Policy Management Group at 1-800-451-1584.

DI-NDTI-BO603 ND R 9797787 0001763 Y W

Block 3 . DESCRIPTION/PURPOSE will. be measured. The document is a compilation of individual test procedures €or related elements of a system, subsystem, or equipment.

1"""""""""""""--"""-"""-~""""""""""""""""-

Block 10. PREPARATION INSTRUCTIONS (continued)

10.2.1.2 Record of chancres. A record of change pages shall be included t o provide for tracking of changes to the test procedures.

10.2.1.3 Table of contents. A table of contents is required when more than one test procedure is included in the test procedures document. It shall identify the page location of each procedure number, procedure title, and related equipment nomenclature.

10.2.2 Bsdv of document. For each test procedure, the following information is required:

10.2.2.1 Procedure number. Each procedure shall have an unique number assigned to it.

18.2.2.2 Title of procedure. The title should relate to the purpose of the test.

10.2.2.3 Introduction. The following shall be addressed in the introduction:

10.2.2.3.1 PurDose of test. (As specified in the contract tasking document.)

10.2.2.3.2 Svstem, subsvstem, or eauipment to be tested. The following identification information shall be provided:

e

a. Nomenclature

b. Model or part number.

c. Type of test item (prototype, production item, laboratory

d. Applicable specification.

model, etc. )

10.2.2.3.3 Test reauirements. Includes the following, each related to the prescribing contract requirement paragraph (specification, standard, plan, or work statement).

a. Required tests, and parameters to be measured.

b. Performance requirements, acceptance or compliance limits, and environmental criteria.

10.2.2.3.4 Referenced documents. A list by title, number, date, and sourc@ of those documents cited in the test procedure.

Page 2 of 3 Pages

Management Group at 1-800-451-1584.

DI-NDTI-80603 ND -7777789 0001764 6

DI-NDTI-80603

Block 10. PREPARATION INSTRUCTIONS

10.2.2.4 Required test equipment. Includes the following for each piece of test equipment required to perform the procedure:

a. Nomenclature.

b. Use of test equipment.

c. Model Number (if applicable).

d. Manufacturer (if mandatory).

e. Accuracy and calibration requirements.

f. Range or spectrum of measurements required.

10.2.2.5 Table of tests. This table lists each test performed under the procedure in the sequence it is to be performed, identified to the procedure paragraph and the related specification/contract requirement.

10.2.2.6 Step-bv-step procedure. The following shall be included for each step of the test procedure:

a. Test Set-up diagrams, including test equipment connections.

b. Input and output instrumentation points.

c. Test item operating limits and test conditions to be

d. Performance parameters to be measured.

e. Step-by-step operations to obtain the required data.

f. Caution and safety warnings as appropriate.

imposed.

10.2.2.7 Data sheets. Data sheets shall be included wi th the procedure, or be separately attached at the end of all procedures. They shall provlde for:

a. Identification of item tested, including model and serial

b. Recording of test measurements.

c. Identification of required or objective performance values,

d. Identification of applicable procedure paragraph.

e. Date of test.

f. Signature of technician or inspector performing the tests.

numbers.

with tolerances.

10.2.2.8 Support requirements. Any special support requirements would be included in this section, such as:

a. Use of special facilities or test ranges.

b. Personnel requirements (numbers, types, qualifications).

c. Unusual electrical, hydraulic, pneumatic, etc. requirements.

d. Support equipment requirements.

Page 3 of 3 Pages

Management Group at 1-800-451-1584.