Maintenance Test and Support Equipment Requirements List DI-ILSS-80294A.pdf

DATA ITEM DESCRIPTION 1 Form Approved

OMB NO. 0704-0188

I

1. TITLE

MAINTENANCE, TEST AND SUPPORT EQUIPMENT REQUIREMENTS LIST

2. IDENTIFICATION NUMBER

DI-ILSS-80294A

3. DESCRIPTION/PURPOSE

3.1 The maintenance test and support equipment (MT&SE) requirements list identifies the test parameter requirements for maintenance;test, alignment, and calibration, to support all echelons of maintenance during the operational life cycle of a system or equipment.

This list als'o identifies the unique and special tools, materials, and test equipment required to support all echelons of maintenance. (continued on page 2)

4. APPROVAL DATE 5. OFFICEOF PRIMARY RESPONSIBILITY (OPR) 6a. DTlC APPLICABLE 6b. GlDEP APPLICABLE

(YYMMDD) G/T213

900716 7.APPLlCATlONllNTERRELTlONSHlP 7 . 1 This Data Item Description (DID) contains the format and content preparation instructions for the data product generated by the specific and discrete task requirement as delineated in the contract.

7.2 This data item is applicable to all Government contracts requiring disclosure of specific MTCSE equipment and its justification.

7.3 This DID supersedes DI-ILSS-80294.

B. APPROVAL L!?JlTATION 9a. APPLICABLE FORMS 9b.AMSC NUMBER

G4968

10 PREPARATION INSTRUCTIONS

10.1 Content and Format. The Maintenance Test and Support Equipment requirements list (MTCSE) includes the support equipment, tools and materials, including computer maintenance and support hardware and software required to maintain the system or equipment at the level of maintenance identified in the contract. The list does not include (a) test alignment and calibration equipment built into the system configuration for test and monitoring, (b) equipment required to repair or calibrate items on the MTCSE list, or (c) common hand tools. The Maintenance Test and Support Equipment Requirements List shall contain two separate parts, a General Purpose MTCSE and a Special Purpose MTCSE.

10.1.1 General Purpose Maintenance Test and Support Equipment Requirements. This part includes generic test equipment that is commercially available which normally can be used for more than one purpose. (Reference sample format in Figure 1.)

10.1.2 Special Purpose Maintenance Test and Support Equipment Requirements . This part lists unique jigs, fixtures and special test equipment, including single source and proprietary items. (Reference sample format in Figure 2 . )

10.2 Item'information. Provides the following information €or each item of test and support equipment on the list. Pertains to both General and Special Purpose MTCSE Requirements Lists.

(continued on page 2)

11. DISTRIBUTION STATEMENT

DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited.

)D Form 1664, MAR 87 Jun 86 edltlon may be used unttl exhausted. Page 1 of 5

Licensed by Information Handling ServicesLicensed by Information Handling Services

DI-ILSS-80294A I L W 7777789 0033595 3

DI-ILSS-80294A

. Description/Purpose (continued)

" 2 This requirements list provides the basis for the using activity to determine if existing cneral purpose test equipment can be utilized, which in many cases will eliminate procurement wquirements, The unique and special tools, materials, and test equipment list provides the asis €or the acquisition and subsequent support of each new item.

O . Preparation instructions (continued)

0.2.1 System or Equipment Under Test. Identifies the application of a recommended test item o system, subsystem, individual equipment, module, or component. Items subject to test shall e identified by the following:

a. Manufacturer/Commercial and Government Entity ( C A G E ) code.

b, Modellpart Number C. Item Name

0.2.2 Parameters To Be Tested. Describe the test, adjustment, or calibration to be srformed. Be as general as possible, including only absolute requirements. This information eflects the actual characteristics required by the prime equipment rather than the haracteristics of the particular model of support or test equipment which may be recommended.

ilclude the following:

a, Nature of test.

b. Value or range of values.

C. Tolerance of these values.

O. 2.3 RecommLnded MT&SE .

0.2.3.1 General Purpose MT&SE. List a generic name for each item, such as, oscilloscope, oltmeter, card extender, etc.

0.1.3.2 Special Purpose MT&SE. When a specific item of MT&SE is required, describe the item ully in accordance with paragraph 10.2,l.a,b and c above. List all special purpose MT&SE eparately from the general items. Additionally, include a statement justifying the selection f each item of special purpose MT&SE. Include the unit price for each of these items.

0.2.4 Quantity On-Site, Record the number. of support equipments required to perform the test escribed at the local site.

0.2.5 Quantity Off-Site. Record the number of support equipments required to perform the est described at the next higher echelon of maintenance, such as the depot.

age 2 'of 5 Pages

10. Preparation Instructions (continued)

10.3 Optional data. A separate list of commercially available test equipment having the necessary capabilities to perform the pr.eceding tests may be submitted. Using this option does not suspend the requirement for the General and Special MT&SE Requirements Lists. This list shall include as a minimum:

a. Manufacture, CAGE code

b. Partfkodel number c . List of Options

d. Nomenclature and NSN if available

e. Unit cost

Page 3 of 5 Pages

DI-ILSS-80274A I L W 7777787 0033577 7 M

GENERAL PURPOSE MAINTENANCE, TEST, AND SUPPORT EQUIPMENT REQUIREMENTS LIST

SE

ITEM

NO.

marks :

SYSTEM/EQUIPMENT

TO BE TESTED UNDER TEST

PARAMETERS QTY

OFF ON RECOMMENDED MT&SE

QTY

SITE SITE

ACCUDATA 117

BANDPAS S (OBC28)

@ 1 VRMS +/- 5 % DC AMPLIFIER

1 O RMS VOLTMETER 30 HZ - 20 KHZ

SAME - 1 O OSCILLOSCOPE 10 V P-P FROM

30 HZ - 20 KHZ

VISUAL DISTORTION

SAME 1 O DC VOLTMETER DC PWR SUPPLY

5 VDC +/- 0.01V

10 VDC +/- 1V

14.5 VDC +/- 0.1V

W/100 KOHM MIN

INPUT IMPEDANCE

GENEEUL/MULITPLE O 1 MULTIMETER AC LINE CORD

USE CONTINUITY

FIGURE 1, Sample Format

DI-ILSS-BO294A IL 9797989 0033578 9

SPECIAL PURPOSE MAINTENANCE, TEST, AND SUPPORT EQUIPMENT REQUIREMENTS

SE

ITEM

NO.

SYSTEM/EQUIPMENT

UNDER TEST

85-02277-002 (33875)

HEATSINK ASSY .

441C -

RECORDER PRECISION

ECHO (54089)

HP-3964A (28480)

RECORDER

I I

'ustification Statement:

PARAMETERS

TO BE TESTED I RECOMMENDED MT&SE

RECTIFIER

INSTALLATION

ADJUSTMENT

TAPE

TENSION

ADJUSTMENT

ALIGNMENT TOOL

GE 118C8388Pl

TAPE TENSION GAGE

T2-H20-1

TENTEL (54632)

POWER

REGULATION

TRANSFORMER

MT3A GENRAD (24655) 85-135 VAC

VARIABLE

QTY

ON

SITE

QTY

OFF

SITE

O

J

1. This alignment t o o l is specifically designed for replacement of the rectifier and i f not used will cause early failure of the rectifier due to insufficient heat transfer via the heat sink. No other tool available meets requirements.

!hit cost $50.00 EA 2 , This is the only known gage that will accurately measure tape tension for this adjustment.

'Jnit cost $350.00 EA

3. No other transformer available meets requirements.

Snit cost $212.00 EA

Figure 2, Sample Format