MIL-STD-2073-1E.pdf

NOT MEASUREMENT

SENSITIVE

MIL-STD-2073-1E

w/CHANGE 1 7 January 2011

SUPERSEDING

23 May 2008

DEPARTMENT OF DEFENSE

STANDARD PRACTICE FOR

MILITARY PACKAGING

AMSC N7296 AREA PACK

ii

FOREWORD

1. Details and decision logic for the use of this standard are described in 1.1, 1.2, and figure 1.

2. This standard is approved for use by all Departments and Agencies of the Department of Defense.

3. For additional guidance on the contents of this document, contact the Commanding Officer, Naval Air Warfare Center Aircraft Division Lakehurst, (Code 6.7.2.4), Bldg. 596-2, Highway 547, Lakehurst, NJ 08733.

4. Comments, suggestions, or questions on this document should be addressed to:

Commanding Officer, Naval Air Warfare Center Aircraft Division, (Code 4L8000B120-3), Highway 547, Lakehurst, NJ 08733-5100, or email to michael.sikora@navy.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https://assist.daps.dla.mil.

iii

CONTENTS

Paragraph Page

1. SCOPE

1.1 Purpose

1.2 Applicability

2. APPLICABLE DOCUMENTS

2.1 General

2.2 Government documents

2.2.1 Specifications and standards

2.2.2 Other Government documents, drawings and publications

2.3 Non-Government publications

2.4 Order of precedence

3. DEFINITIONS

3.1 General

3.2 Categorization

3.3 Common group items

3.4 Consumable

3.5 Container Design Retrieval System (CDRS)

3.6 Critical items

3.7 Electrostatic Discharge Sensitive (ESDS) items

3.8 Fragility factor

3.9 Hazardous material

3.10 Military packaging

3.11 Packaging design validation

3.12 Repairable item

3.13 Reusable container

3.14 Sealed

3.15 Selective group items

3.16 Special group items

4. GENERAL REQUIREMENTS

4.1 General

4.1.1 Options

4.2 Development of military packaging details and data requirements

4.3 Hazardous material

iv

CONTENTS (Continued)

4.4 Packaging of classified items

4.5 Quantity per unit pack (QUP)

4.6 Containers

4.7 Kits

4.8 Repairable excess and residual parts

4.9 Loose fill materials

4.10 Shock and vibration absorption

4.11 Determination of item fragility

4.12 Packaging materials

5. DETAILED REQUIREMENTS

5.1 General military package design considerations

5.2 Military preservation

5.2.1 Cleaning and drying

5.2.2 Preservatives

5.2.2.1 Preservative applicability

5.2.2.2 Application of contact preservatives

5.2.2.3 Application and use criteria of volatile corrosion inhibitors (VCI)

5.2.3 Methods of military preservation - general requirements

5.2.3.1 Surfaces coated with preservatives

5.2.3.2 Metal surfaces not coated with preservatives

5.2.3.3 Method 10 - Physical protection

5.2.3.4 Method 20 – Physical protection with preservative (with greaseproof wrap, as required)

5.2.3.5 Method 30 - Waterproof or waterproof-greaseproof protection with preservative

5.2.3.5.1 Method 31 - Waterproof bag, heat sealed

5.2.3.5.2 Method 32 - Container, waterproof bag, heat sealed

5.2.3.5.3 Method 33 - Greaseproof-waterproof bag, heat sealed

5.2.3.6 Method 40 - Watervaporproof protection with

preservative as required

5.2.3.6.1 Method 41 - Watervaporproof bag, heat sealed

5.2.3.6.2 Method 42 - Container, watervaporproof bag, heat sealed, container

5.2.3.6.3 Method 43 - Floating watervaporproof bag, heat sealed

5.2.3.6.4 Method 44 - Rigid container (other than metal), sealed

5.2.3.6.5 Method 45 - Rigid metal container, sealed

v

5.2.3.7 Method 50 - Watervaporproof protection with desiccant

5.2.3.7.1 Method 51 - Watervaporproof bag with desiccant, heat sealed

5.2.3.7.2 Method 52 - Container, watervaporproof bag with

desiccant, heat sealed, container

5.2.3.7.3 Method 53 - Floating watervaporproof bag with

desiccant, heat sealed

5.2.3.7.4 Method 54 - Rigid container (other than metal) with desiccant, sealed

5.2.3.7.5 Method 55 - Rigid metal container with desiccant, sealed

5.2.4 Military preservation requirements for items with

specific characteristics

5.2.4.1 Electrostatic discharge sensitive (ESDS) items

5.2.4.2 Items capable of disassembly

5.2.4.3 Flexible-coilable items

5.2.4.4 Caging or damping

5.2.4.5 Items with mounts

5.2.4.6 Rubber and synthetic rubber items

5.2.4.7 Hazardous items

5.2.4.8 Moveable parts

5.2.4.9 Items compatible with VCI

5.2.4.10 Vacuum sensitive items

5.3 Level A and B packing requirements

5.3.1 Intermediate containers

5.3.2 Exterior containers

5.3.2.1 Container selection

5.4 Minimal packing requirements

5.5 Marking

5.6 Military packaging design validation provisions

5.7 Quality assurance provisions

6. NOTES

6.1 Intended use

6.2 Acquisition requirements

6.3 Associated Data Item Descriptions (DIDs)

6.4 Testing facilities

6.5 Subject term (key word) listing

6.6 Copies of regulations

vi

6.7 Changes from previous issue

6.8 Changes in methods of preservation designations

6.9 Conversion of heat sealable bag designators

6.10 Supersession

FIGURES

Figure Page

1 Military packaging requirements development decision chart

TABLES

Table Page

I Approximate fragility factors II Method of preservation vs. appropriate MIL-DTL-117 bag designations and materials III Heat-sealable bag designator conversion chart vii

APPENDICES

APPENDIX A

DEVELOPMENT OF MILITARY PACKAGING REQUIREMENTS

A.1 SCOPE

A.2 APPLICABLE DOCUMENTS

A.2.1 General A.2.2 Government documents A.2.2.1 Specifications and standards A.2.2.2 Other Government documents, drawings and publications A.2.3 Non-Government publications

A.3 USE OF EXISTING PACKAGING REQUIREMENTS

A.3.1 Application

A.4 HAZARDOUS MATERIAL

A.4.1 General A.4.2 Hazardous material package testing A.4.3 Hazardous material shipment documentation

A.5 MILITARY PACKAGING CODE DEVELOPMENT

A.5.1 Item classification A.5.2 Item characteristics A.5.3 Categorization A.5.3.1 Category code A.5.3.2 Category code development A.5.3.2.1 First category – physical and chemical characteristics A.5.3.2.1.1 Item composition/properties criteria A.5.3.2.1.2 Critical item criteria A.5.3.2.1.3 Contact preservative criteria A.5.3.2.2 Second category – weight/size/fragility A.5.3.2.3 Third category – preservatives A.5.4 Military packaging code development A.5.4.1 Military packaging codes for common items A.5.4.2 Military packaging codes for selective items A.5.5 Recording of developed packaging data viii

APPENDICES (Continued)

APPENDIX A (Continued)

A.6 CONTAINER SELECTION

A.7 FORMULAS

A.8 PACKAGING DESIGN VALIDATION

A.8.1 Common items A.8.2 Selective and special items

A-1 Format for interpretation of packaging code sequence A-2 Military packaging data development flow chart

A-I Physical and chemical characteristics category code determination A-II Weight/size/and non-operational fragility category code determination A-III Contact preservative category code determination A-IV Predetermined military packaging data for common items A-V Calculation of material sizes and weights A-VI Procedural packaging specifications ix

APPENDIX B

FACTORS AND FORMULAE ESTABLISHING MILITARY PACKAGING QUP AND ICQ

B.1 SCOPE

B.2 APPLICABLE DOCUMENTS

B.3 DETERMINATION OF QUP

B.3.1 Repairable items (depot or field level) or items designated Hi-value or Hi-priority B.3.2 Consumable items B.3.3 Irregular configuration, delicate or fragile items B.3.4 Pairs and sets items B.3.5 Items unit packed in accordance with Method 50 B.3.6 Kit B.3.7 Lumber, raw stock, paints, oils and dope B.3.8 Factors and formulae establishing QUP B.3.8.1 Consumable items having both maintenance and overhaul applications B.3.8.2 Consumable items having overhaul applications only

B.4 QUANTITY PER UNIT PACK DETERMINATION FORMULAE

B.4.1 Formula A B.4.2 Formula B

B.5 DETERMINATION OF ICQ

B.5.1 Quantities per intermediate container B.5.2 Intermediate container limitations

B-I Guidance for establishing number of unit packs per intermediate container x

APPENDIX C

CONTAINERS

C.1 SCOPE

C.2 APPLICABLE DOCUMENTS

C.2.1 General C.2.2 Government documents C.2.2.1 Specifications, standards and drawings C.2.2.2 Other Government Documents, Drawings and Publications C.2.3 Non-Government publications

C.3 GENERAL

C.3.1 Unit container size C.3.2 Use of unit containers as shipping containers

C.4 EXPENDABLE CONTAINERS

C.4.1 Interior containers C.4.2 Exterior containers

C.5 REUSABLE CONTAINERS

C.5.1 Specialized containers C.5.1.1 Design C.5.1.2 Container Design Retrieval System (CDRS) C.5.1.3 Specialized shipping containers for ordnance C.5.2 Multiapplication containers C.5.2.1 Design and selection C.5.2.2 Identification C.5.2.3 Coded data C.5.2.4 Packaging design validation C.5.2.5 Short life containers C.5.2.6 Long life containers C.5.2.7 Multiapplication container availability C.5.2.7.1 General Services Administration (GSA) xi

APPENDIX C (Continued)

C.5.2.7.2 Naval Inventory Control Point (NAVICP) C.5.2.7.3 Commercial sources

C-I Interior containers C-II Exterior shipping containers - selection by maximum weight of contents and level of packing C-III Fiberboard container size list C-IV Multiapplication container selection

APPENDIX D

DEVELOPMENT OF MILITARY PACKAGING REQUIREMENTS FOR KITS (PARTS AND

MODIFICATION)

D.1 SCOPE

D.2 APPLICABLE DOCUMENTS

D.3 PRESERVATION

D.3.1 Consolidation of different items within a method of preservation D.3.2 Application of preservative compounds or oils D.3.2.1 Kits procured for oxygen equipment D.3.2.2 Preservation procedures D.3.2.3 Items susceptible to corrosion (iron, steel, magnesium, etc.)

D.4 UNIT PRESERVATION

D.4.1 Physical protection D.4.2 Segregation of items within packs D.4.3 Skin packaging xii

APPENDIX D (Continued)

D.4.3.1 Skin packaging metals D.4.3.2 Skin packaging shims or gaskets

D.5 PACKING AND MARKING OF KITS

APPENDIX E

MILITARY PACKAGING DATA FORMS

E.1 SCOPE

E.2 APPLICABLE DOCUMENTS

E.2.1 General E.2.2 Government documents E.2.2.1 Standards E.2.2.2 Other Government documents, drawings, and publications E.2.3 Non-Government publications

E.3 GENERAL REQUIREMENTS

E.3.1 Development of military packaging data E.3.2 Recording military packaging data E.3.2.1 Recording of data E.3.2.2 National Stock Number (NSN) requirements E.3.2.3 Coded data E.3.2.4 Kits (Parts and Modification) E.3.2.5 Special packaging instructions

E.4 DETAILED REQUIREMENTS

E.4.1 Development of military packaging data E.4.1.1 Procedural specification data E.4.2 Preparation of military packaging data E.4.2.1 Nomenclature E.4.2.2 Manufacturer's Commercial and Government Entity code and part number E.4.2.3 Configuration item (CI) E.4.2.4 Item identification data xiii

APPENDIX E (Continued)

E.4.2.5 Preservation and packing data E.4.2.6 Supplemental data E.4.2.7 Special packaging instruction (SPI) data

E.5 SPECIAL PACKAGING INSTRUCTIONS

E.5.1 General E.5.2 Format E.5.3 Elements E.5.4 Detailed requirements E.5.4.1 Package assembly instructions E.5.4.2 Bill of materials E.5.4.3 Specification containers

E.6 APPROVAL OF CONTRACTOR DEVELOPED PACKAGING

DATA

E.6.1 Procedures for submitting data for approval E.6.1.1 Approval of data without National Stock Numbers E.6.1.2 Approval of data for emergency shipments E.6.1.3 Approval of data of interest to one DoD agency E.6.1.4 Use of background data for approval E.6.1.5 Data for common items E.6.2 Return of approved data E.6.3 Authentication E.6.4 Transmittal of data E.6.4.1 Military packaging data E.6.4.2 Special packaging instructions xiv

APPENDIX E (Continued)

E-1 Preservation and Packing Data

E-I Item identification data for PART A of DD Form 2326 E-II Preservation - Packing data for PART B of DD Form 2326 E-III. Supplemental data for PART C of DD Form 2326 E-IV Special packaging instruction data for PART D of DD Form 2326

APPENDIX F

MILITARY PACKAGING DESIGN VALIDATION PROVISIONS

F.1 SCOPE

F.2 APPLICABLE DOCUMENTS

F.2.1 General F.2.2 Government documents F.2.2.1 Standards F.2.2.2 Other Government documents F.2.3 Non-Government publications

F.3 GENERAL

F.3.1 Packaging design validation tests F.3.2 Hazardous material F.3.3 Ammunition unit loads

F.4 TEST METHODS

F.4.1 Container performance tests F.4.2 Preservation tests xv

APPENDIX F (Continued)

F.5 OTHER

F.5.1 Acceptance criteria and disposition of test samples

APPENDIX G

QUALITY ASSURANCE PROVISIONS

G.1 SCOPE

G.2 APPLICABLE DOCUMENTS

G.2.1 General G.2.2 Government documents G.2.2.1 Specifications and standards

G.3 GENERAL

G.3.1 Quality system G.3.2 Quality assurance requirements G.3.3 Sampling G.3.3.1 Lot size G.3.3.2 Sampling for inspection

G.4 PRESERVATION INSPECTIONS

G.4.1 Visual preservation examinations G.4.2 Leakage test G.4.2.1 Wetting G.4.2.2 Selection of technique G.4.2.2.1 Vacuum retention technique G.4.2.2.1.1 Sealed rigid container G.4.2.2.1.2 Sealed flexible bag G.4.2.2.2 Submersion (or immersion) technique G.4.2.2.3 Pneumatic pressure technique G.4.2.2.4 Hot water technique G.4.2.2.5 Squeeze technique (applicable only to flexible specimens) xvi

APPENDIX G (Continued)

G.4.3 Heat-sealed seam test G.4.3.1 Selection of unit pack samples G.4.3.1.1 Alternate unit pack sampling procedure G.4.3.2 Heat sealed seam strength testing

G.5 PACKING INSPECTIONS

G.5.1 Examination procedures

G-I Preservation inspection provisions G-II Leakage and heat-sealed seam test provisions

APPENDIX H

PROCEDURES FOR COMPLIANCE WITH CONTAINER

DESIGN RETRIEVAL SYSTEM (CDRS) REQUIREMENTS

H.1 SCOPE

H.2 APPLICABLE DOCUMENTS

H.3 DETAILED REQUIREMENTS

H.3.1 Design search request submittal H.3.2 CDRS Office search response H.3.3 Design activity action on CDRS Office response H.3.3.1 Negative response from CDRS Office H.3.3.1.1 Submittal of container design data H.3.3.2 Positive response from CDRS Office H.3.3.2.1 Item (Inventory) manager notification H.3.3.2.2 Container design agent notification xvii

APPENDIX J

MILITARY PACKAGING REQUIREMENT CODES

J.1 SCOPE

J.2 APPLICABLE DOCUMENTS

J.2.1 General J.2.2 Government documents J.2.2.1 Specifications, standards and handbooks J.2.2.2 Other Government documents, drawings and publications J.2.3 Non-Government publications

J.3 GENERAL REQUIREMENTS

J.3.1 Code system J.3.2 Procedure and responsibilities for revisions J.3.2.1 Adding codes

J.4 DETAILED REQUIREMENTS

J.4.1 General code requirements J.4.2 Preservation methods J.4.2.1 Specialized preservation J.4.3 Quantity per unit pack J.4.4 Cleaning J.4.5 Preservative J.4.6 Wrapping material J.4.7 Cushioning and dunnage J.4.8 Thickness of cushioning or dunnage J.4.9 Unit and intermediate container J.4.9.1 Options J.4.10 Unit container level and optional procedure indicator codes J.4.11 Unit packs per intermediate container J.4.12 Intermediate container J.4.12.1 Intermediate container limitations J.4.13 Packing J.4.14 Special markings

J.5 CROSS INDEX

J.5.1 Document number to table and code xviii

APPENDIX J (Continued)

J-I Methods of preservation codes J-Ia Specialized preservation codes J-II Cleaning procedure codes J-III Contact preservative material codes J-IIIa Contact preservative material codes in specification sequence J-IV Wrapping material codes J-IVa Wrapping material codes in specification sequence J-V Cushioning and dunnage material codes J-Va Cushioning and dunnage material codes in specification sequence J-VI Thickness of cushioning or dunnage codes J-VII Unit and intermediate container codes J-VIIa Unit and intermediate container codes in specification sequence J-VIII Unit container level codes J-VIIIa Optional procedure indicator codes J-IX Level A military packing requirement codes J-IXa Level B military packing requirement codes J-IXb Minimal packing requirement codes J-X Special marking codes J-XI Document number to table and code cross-reference index

INDEX

1. SCOPE

1.1 Purpose. This document outlines standard processes for the development and documentation of military packaging. This standard covers methods of preservation to protect materiel against environmentally induced corrosion and deterioration, physical and mechanical damage, and other forms of degradation during storage, multiple handling, and shipment of materiel in the defense transportation system. A decision chart is included for determining how to develop military packaging requirements (see figure 1). If military packaging is applicable, figure 1 will further aid in the development of detailed packaging requirements.

1.2 Applicability. The requirements of this standard apply to items for which military packaging is required to meet operational demands. These items include but are not limited to:

a. Items delivered during wartime for deployment with or sustainment to operational units

b. Items that are depot level repairables

c. Items requiring reusable containers

d. Items intended for delivery-at-sea

e. Security Assistance/Foreign Military Sales/Grant Aid (unless otherwise directed by the destination country)

Is item haza rdous?

P ackag e IAW A.4 Is item co ns umable?

Is item frag ili ty factor less tha n 5 0 G 's?

Is i tem fragi lity fa cto r equal to or grea ter than 85 G' s?

(See 3.8 and T able I)

Are i tem weig ht & dimensions wi th in l imits specified by T able A-II?

Ca teg ori ze I AW A ppendix A a s common item

Can i tem pa ckaging be des cri bed by codes in Appendix J a nd s upplemental da ta ?

Select Appendix J codes and add supplemental data, a s req 'd (selective item); (See 5.6 fo r vali da tion requirement)

Is special ized l ong li fe co ntai ner required?

(See C.5)

Interroga te C onta iner Desi gn Retri ev al Sys tem (CDRS) (See C. 5.1.2)

Is C DRS respons e pos itive?

Use desig n "AS I S" o r modify if required.

Determi ne a vailab ili ty of s ui ta bl e co ntainers in DoD invento ry fo r reuse and va lidate use fo r i tem

Desig n pa ckage using speci al packaging instructio n (SPI ) gu ide-lines s pecified in Appendix E (See 5 .6 for val idatio n requirements )

Are item weight, d imensions and fra gil ity factor wi th in l imits speci fied fo r containers lis ted in T able C-IV?

Are item weight a nd d imensio ns wi thin limi ts s pecified for containers li sted i n T able C-IV?

Do mul ti-appl ication containers meet logi stic needs?

C oul d items of l ower or unknown fragi lity be protected by multi -a pp li ca tion contai ners? (See T able C-IV)

Is it cost effective to us e multi-applicatio n containers?

W il l 10 trip s ho rt li fe contai ner meet lo gis tics needs? Can item packa ging be described by codes in Appendix J and supplementa l data, as req'd?

Use 10 trip s ho rt li fe co nta iner (See C.5 .2.5)

Wil l 10 0 trip long life co ntainer meet logi stics needs?

Use 10 0 trip long life container (See C. 5.2.6)

Select Appendix J codes IAW Appendix A format (See 5.6 fo r va lidati on requirements )

NO YES

YES NO

YE S NO

NO NOYES YE S

NOYE S

NOYE S

YES YE S N ON O

Y ES N O

YE S NO

Y ES NO

YES NO

YE S NO

YE S NO

YES NO

FIGURE 1. Military packaging requirements development decision chart.

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this standard. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this standard, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

FEDERAL SPECIFICATIONS

QQ-A-1876 - Aluminum Foil.

PPP-B-1672 - Box, Shipping, Reusable with Cushioning.

COMMERCIAL ITEM DESCRIPTION

A-A-3174 - Plastic Sheet, Polyolefin.

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-DTL-117 - Bags, Heat-Sealable.

MIL-PRF-121 - Barrier Materials, Greaseproof, Waterproof, Flexible, Heat-Sealable.

MIL-PRF-131 - Barrier Materials, Watervaporproof, Greaseproof, Flexible, Heat-Sealable.

MIL-PRF-3420 - Packaging Materials, Volatile Corrosion Inhibitor, Treated, Opaque.

MIL-D-3464 - Desiccants, Activated, Bagged, Packaging Use and Static

Dehumidification.

MIL-DTL-6060 - Bags, Watervaporproof, Heat-Sealable, Complex.

MIL-I-8574 - Inhibitors, Corrosion, Volatile, Utilization of.

MIL-PRF-16173 - Corrosion Preventive Compound, Solvent Cutback, Cold-Application.

MIL-PRF-22019 - Barrier Materials, Transparent, Flexible, Sealable, Volatile Corrosion Inhibitor Treated.

MIL-DTL-22020 - Bags, Transparent, Flexible, Sealable, Volatile Corrosion Inhibitor Treated.

MIL-PRF-22191 - Barrier Materials, Transparent, Flexible, Heat-Sealable.

MIL-PRF-81705 - Barrier Materials, Flexible, Electrostatic Protective, Heat-

Sealable.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-129 - Military Marking for Shipment and Storage.

MIL-STD-3010 - Test Procedures for Packaging Materials.

MS20003 - Indicator, Humidity, Card, Three Spot, Impregnated

Areas (Cobaltous Chloride).

(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch or https://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2.2 Other Government documents, drawings and publications. The following other Government documents, drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

DEPARTMENT OF DEFENSE MANUAL

DoD-5220.22M - National Industrial Security Program Operating Manual

(NISPOM).

(Copies of this document is available online at http://www.DTIC.mil/ or from the National Technical Information Services (NTIS), 5285 Port Royal Road, Springfield, VA 22161.)

CODE OF FEDERAL REGULATIONS (CFR)

29 CFR - Labor.

40 CFR - Protection of Environment.

49 CFR - Transportation.

(Copies of these documents are available online at www.gpoaccess.gov/cfr/ or from the Superintendent of Documents, U.S. Government Printing Office, North Capital & “H” Streets, N.W., Washington, DC 20402-0002.)

2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

ASTM INTERNATIONAL

ASTM-D996 - Standard Terminology of Packaging and Distribution

Environments (DoD adopted).

ASTM-D1974 - Standard Practice for Methods of Closing, Sealing, and

Reinforcing Fiberboard Boxes (DoD adopted).

ASTM-D4279 - Standard Test Methods for Water Vapor Transmission of Shipping

Containers – Constant and Cycle Methods.

ASTM-D5118/ - Standard Practice for Fabrication of Fiberboard Shipping Boxes

D5118M (DoD adopted).

ASTM-D5168 - Standard Practice for Fabrication and Closure of Triple Wall

Corrugated Fiberboard Containers (DoD adopted).

(Copies of these documents are available online at http://www.astm.org or from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.)

SAE INTERNATIONAL

SAE-AS26860 - Indicator, Humidity, Plug, Color Change (DoD adopted).

(Copies of this document are available online at http://www.sae.org or from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096.)

2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

3. DEFINITIONS

3.1 General. Definitions of terms unique to this standard are listed below. Definitions of other terms commonly used in the packaging community may be found in ASTM-D996.

3.2 Categorization. The process of evaluating an item by chemical and physical characteristics that are significant in determining the preservation requirements.

3.3 Common group items. Items with a fragility rating of 85 G's (see 3.8) or more which have no dimension greater than 24 inches and weigh not more than 10 pounds for which predetermined packaging has been developed (see A.5.4.1 and table A-IV). Hazardous materials, electrostatic discharge sensitive items, shelf life items, sets, outfits, and kits are excluded from this group regardless of their fragility, size, or weight.

3.4 Consumable. An item of supply (except explosive ordnance, major end items of equipment, and repairables) that is normally expended or used up beyond recovery in the use for which it was designed or intended.

3.5 Container Design Retrieval System (CDRS). A management system program to provide a DoD centralized automated data base system for storing, retrieving and analyzing existing container designs and test information concerning specialized containers. The purpose of the CDRS is to avoid duplication in container designs, minimize the number of new container designs being developed and promote reuse of existing DoD specialized containers for new item development and procurement (see Appendix H).

3.6 Critical items. Items meeting one or more of the following criteria are considered critical.

a. Critical chemically. Items which are of such a nature that any degree of deterioration (in the form of corrosion, stain, scale, mold, fungi, or bacteria) caused by oxygen, moisture, sunlight, living organisms, and other contaminants which are time or temperature dependent, will result in premature failure or malfunction of the item or equipment in which the item is installed or with which the item interfaces.

b. Critical physically. Items that would become unfit for use as a result of physical action on the item or any integral surfaces thereof. This includes, but is not limited to, items having a surface finish of 64 microinches root mean square or less, items which have surfaces that mate with surfaces of other parts, optical and reflective devices having highly polished surfaces, items requiring a high degree of cleanliness, and items requiring special protection against shock, vibration, or abrasion.

c. Critical application. Items that, either in assembly or operation, provide an essential attribute to attaining critical military objectives.

3.7 Electrostatic Discharge Sensitive (ESDS) items. Electronic items that are susceptible to damage or degradation as a result of an electrostatic discharge event.

3.8 Fragility factor. Maximum force acceleration or deceleration expressed in units of gravity (G's) that can be applied to an item in its non-operating state without causing physical damage or changes in its operational characteristics. The fragility factor is expressed in units of acceleration for a defined shock pulse. Shock pulse forms and durations which approximate the transportation and handling environment are to be used in determining the fragility factor.

Representative fragility factors for various classes of items are listed in table I.

3.9 Hazardous material. A material, substance, or waste that has been determined by the Secretary of Transportation to be capable of posing an unreasonable risk to health, safety, and property when transported in commerce and that has been so designated. (This includes all items listed as hazardous in Titles 29, 40 and 49 CFR and other applicable modal regulations effective at the time of shipment.)

3.10 Military packaging. A means of specifying the military preservation and packing that a given item requires to ensure that it is not degraded during shipment and storage.

a. Military preservation. Application of materials and/or methods designed to protect an item during shipment, handling, indeterminate storage and distribution to consignees worldwide.

b. Military packing. Application of any exterior protective methods, materials, or devices to assure the integrity of the preserved item as follows:

(1) Level A. Protection required to meet the most severe worldwide shipment, handling, and storage conditions. A Level A pack must, in tandem with the applied method of preservation, be capable of protecting material from the effects of direct exposure to extremes of climate, terrain, and operational and transportation environments. Examples of situations which indicate a need for use of a Level A pack are: War Reserve Material, mobilization, strategic and theater deployment and employment, open storage, deck loading and Foreign Military Sales (as specified in the contract). Examples of containers used for Level A packing requirements include, but are not limited to, overseas type wood boxes, and plastic and metal reusable containers.

(2) Level B. Protection required to meet moderate worldwide shipment, handling, and storage conditions. A Level B pack must, in tandem with the applied preservation, be capable of protecting material not directly exposed to extremes of climate, terrain, and operational and transportation environments. Examples of situations which indicate a need for use of a Level B pack are: security assistance, such as Foreign Military Sales (as specified in the contract) and containerized overseas shipments. Examples of containers used for Level B packing requirements include, but are not limited to, domestic wood crates, weather-resistant fiberboard containers, fast pack containers, weather-resistant fiber drums, and weather-resistant paper and multi-wall shipping sacks.

3.11 Packaging design validation. Testing to ascertain the capability of the prototype pack to protect the integrity and serviceability of the item(s) for which the package is designed.

3.12 Repairable item. An item that, by the application of engineering, economic, and other factors, could be reasonably restored to a serviceable condition through regular repair procedures.

3.13 Reusable container. A shipping and storage container that can be reused without impairment of its protective function and that can be repaired or retrofitted to prolong its life or modified to adapt it for shipment of items other than that for which it was originally intended.

Reusable shipping and storage containers are further defined as follows:

a. Long life container (100 trips minimum). A shipping container that can be used repeatedly, and whose service life can be expected to equal the service life of the item it is designed to protect. These containers may be refurbished by appropriate maintenance practices to their original condition and subsequently reused.

b. Short life container (10 trips minimum). A shipping container that can be reused for a limited number of times. The container is usually made of wood, plywood, fiberboard or similar material that has a limited life.

c. Multiapplication containers. Multiapplication containers are designed to protect a variety of components within a given fragility and size range. They can be manufactured in a similar manner to that used for specialized containers or in accordance with applicable/specified military or federal specifications. A multiapplication container can be either of the short-life or long-life variety. Short life multiapplication containers include "fast packs," consisting of a family of standard size cushioned fiberboard shipping containers of four types. These types are fully described in PPP-B-1672 and are identified as Types I, II, III and IV in table C-IV. Long-life multiapplication reusable containers are designated as Types VI thru X and are also described in table C-IV. These containers are made of rugged plastic construction containing internal cushioning pads or permanent shock mitigation systems (for example, shear mounts, steel coils, and springs) and are designed to protect repairable components packaged therein, during forward and retrograde movements within the military supply system.

d. Specialized container. Specialized containers are generally the long-life variety and are uniquely configured to support and protect a specific item, or limited variety of items, during handling and storage or to protect personnel and equipment from hazardous contents. Containers of this type frequently incorporate energy absorbing systems, temperature control systems or special features to make handling or shipment possible, easier or safer. Engineering drawings, or equivalent, are used to define form, fit, function, materials, tolerances and manufacturing techniques. Internal fixtures and other fitments within specialized shipping containers result from either original design efforts or the redesign or modification of an existing container to meet a specific application or need.

3.14 Sealed. An item is considered sealed if the entrances to the interior of the item are sealed with gaskets or closely mated surfaces under mechanical pressure or are sealed by threaded closure devices (except plastic caps). Sealed items also include assemblies which are encapsulated in plastics, ceramics, glass or metal with completely cemented seams or joints closing the interior to the entrance of liquid water. Hermetic sealing is a seal that will exclude air and is leakproof at ambient temperatures and atmospheric pressures and is usually glass to glass, metal to metal or metal to glass.

3.15 Selective group items. Items that cannot appropriately utilize predetermined packaging developed for common group items (see 3.3) yet do not require a drawing, sketch, illustration, or separate narrative type instruction to specify packaging details.

3.16 Special group items. Items with peculiar characteristics such as weight, configuration, complexity, fragility, or other considerations that cannot be classified as common or selective. An item is considered special if drawings, sketches, illustrations, narrative type instructions, or specialized containers are required to specify packaging details.

4. GENERAL REQUIREMENTS

4.1 General. Military packaging requirements shall be developed using the figure 1 decision chart in accordance with the requirements of this section, Section 5 and all Appendices herein. The developed military packaging requirements shall be documented in accordance with Appendix E and as specified on the Contract Data Requirements List (CDRL) (see 6.3). These requirements are generally defined by a twelve digit position-sensitive code system, as illustrated in figure A-1. Appropriate codes are drawn from those listed in Appendix J. When an item has been determined to be in the special group category, a Special Packaging Instruction shall be required, prepared in accordance with Appendix E and as specified on the CDRL (see 6.3).

4.1.1 Options. Unless otherwise specified in supplemental instructions (see E.4.2.6), all military packaging requirements defined or developed herein shall be mandatory for compliance and no substitutions are permitted. When specified in supplemental instructions (see E.4.2.6), options can be exercised as to the specific method of preservation or DoD approved packaging materials to be used. However, the basic preservation method shall be retained, all other supplemental instructions shall be complied with, and unit package dimensions shall not be increased by more than one inch. Equal or higher degree of protection shall be afforded the item and there shall be no increase in the package cost.

4.2 Development of military packaging details and data requirements. If this standard is cited for use and no specific military packaging details or data requirements are contained in the contract, the contracting officer shall be contacted for same. Appendix A and other applicable sections and appendices of this standard shall be used to develop detailed military packaging requirements in cases where the development of packaging data by the contractor is cited.

4.3 Hazardous material. Packaging for hazardous materials shall be developed in accordance with the requirements specified in A.4.

4.4 Packaging of classified items. Packaging developed for classified items shall meet the requirements of DoD 5220.22M, National Industrial Security Program Operating Manual

(NISPOM).

4.5 Quantity per unit pack (QUP). The QUP shall be determined in accordance with Appendix B.

4.6 Containers. Requirements for containers and their selection for military packaging applications are specified in Appendix C.

4.7 Kits. Military packaging of parts kits or modification kits shall be in accordance with Appendix D.

4.8 Repairable excess and residual parts. Repairable excess and residual part(s) for which packaging has not been stipulated by the acquisition activity shall be packaged to afford adequate protection as required to prevent further deterioration due to rust, corrosion, or physical damage. Unless otherwise specified by the acquisition activity, the QUP shall be one.

4.9 Loose fill materials. Loose fill materials are prohibited in all military packages except for the packaging of peculiar hazardous materials that require their use for absorptive purposes.

4.10 Shock and vibration absorption. Shock and vibration absorption shall be provided by cushioning materials or devices that protect the contents and packaging components from physical damage during handling, shipment and storage. A cushioning medium shall be placed as close to the contents as practicable. A noncorrosive wrap shall be placed between the item and all corrosive type cushioning media.

4.11 Determination of item fragility. Fragility factors in the non-operating state of the item, established in the item specification, shall be used to establish the maximum energy permitted to reach the item during transportation and handling (see 3.8). When fragility factors are not available or established, criteria of table I can be used to approximate G factors. Caution shall be taken to ensure that there are no additional components installed which lower the item fragility rating.

4.12 Packaging materials. The use of new packaging materials or products is encouraged and recommended if their protective capabilities are equivalent to similar approved materials without increasing the overall cost to the government. To expedite the use of these materials prior to their inclusion in government specifications, their prompt use will be permitted under conditions outlined herein. In instances where the material or product is not covered by a specific specification or standard, the manufacturer or fabricator of the material or product shall make available documented test data by an approved testing laboratory, that the material or product meets or exceeds all performance requirements of the specification for a similar material or product. The request for approval shall be submitted to the acquisition activity via the technical packaging element of the contract management activity.

5. DETAILED REQUIREMENTS

5.1 General military package design considerations. Military packaging shall be of minimum cost consistent with required performance. Unit packs shall be designed to conserve weight and cube while retaining the protection required and enhancing standardization.

5.2 Military preservation. The military preservation procedure should be accomplished without interruption. When interruptions are unavoidable, temporary wraps, covers or enclosures shall be provided to insure against contamination or deterioration of the items.

5.2.1 Cleaning and drying. Items shall be cleaned and dried by any process or processes that are not injurious to the item. All items shall pass the applicable cleaning and drying inspection requirements of table G-I.

5.2.2 Preservatives.

5.2.2.1 Preservative applicability. When contact preservatives are required to protect an item from chemical deterioration, they shall conform to table J-III. Preservatives selected shall be those whose application, use, or removal will not damage the item or impair item function.

5.2.2.2 Application of contact preservatives. Directly after cleaning and drying of the item, the required preservative shall be uniformly applied by any appropriate procedure that permits the preservative to coat all necessary surfaces. Suggested methods of application include, but are not limited to:

a. Dipping

b. Flow coating

c. Slushing

d. Brushing

e. Filling or flushing

f. Fogging

g. Spraying

5.2.2.3 Application and use criteria of volatile corrosion inhibitors (VCI). Volatile corrosion inhibitor preservative treatment shall be applied in accordance with the criteria and procedures of MIL-I-8574.

5.2.3 Methods of military preservation - general requirements. There are five basic methods of preservation (MOP) established herein:

Method 10 Physical protection Method 20 Preservative coating only Method 30 Waterproof protection Method 40 Watervaporproof protection Method 50 Watervaporproof protection with desiccant

Various specific techniques, also detailed herein, have been developed to meet the basic Methods 30, 40, and 50 and shall be used as appropriate. The preservation methods shall be as specified in the contract or purchase order. In the absence of such requirements, the appropriate method shall be selected in accordance with the applicable tables of Appendix A. The following general requirements shall apply:

a. Protection from physical damage and mechanical malfunction is required for all methods of preservation in addition to the specific environment protection provided. This requirement shall be validated during conduct of the packaging design validation tests specified in Appendix F.

b. When methods provide either transparent or opaque protection, transparent protection may be furnished at the option of the supplier but is not required unless specifically called for in the contract or purchase order.

c. Protection for all electrostatic discharge sensitive items requires the use of packaging materials to counteract electrostatic and electromagnetic field forces (see 5.2.4.1).

d. When specific methods require using a bag or container, preliminary wrapping, cushioning or other dunnage material shall be applied as necessary to protect the item, the bag, and the container from all projections or sharp edges of the item as well as to restrict movement of the item within the unit pack.

e. When methods require chipboard or fiberboard containers within the bag, the corners and edges of the containers shall be blunted prior to placing the item in the box and enclosing within the bag.

f. When a transparent unit pack is specified, the preliminary wrapping shall also be transparent.

g. Methods of preservation requiring the use of a bag for the interior packaging shall be subject to the use and fabrication procedures and limitations of MIL-DTL-117.

Table II lists the acceptable materials that may be used in constructing bags that meet the requirements of these specific methods of preservation (see 6.9). Bags shall comply with MIL-DTL-6060 when the construction limitations of MIL-DTL-117 are exceeded.

h. All materials used (e.g. wraps, cushioning, dunnage, and barrier bags) shall be as clean and dry as practicable to minimize item susceptibility to corrosion and contaminants.

i. Items with handles, knobs, or other protrusions shall be wrapped or otherwise protected and secured to facilitate equal distribution of shock forces over the entire surface of the item and thus prevent damaging shock forces to the protrusion.

j. When flexible bags are used, the volume of trapped air within the bag shall be kept to a minimum by compressing the bag around the contents, or by carefully drawing a vacuum inside the bag, prior to final heat sealing or cold sealing (for VCI). Caution shall be taken to prevent rupture of the bag, or damage to the item, due to excessive vacuum.

k. Items preserved with VCI-treated materials are exempted from preliminary wrapping.

5.2.3.1 Surfaces coated with preservatives. Preliminary wrapping materials in contact with any item coated with a preservative shall be greaseproof and shall conform to MIL-PRF- 121 or QQ-A-1876. Greaseproof wraps applied solely to confine the contact preservative on item surfaces are not necessary when a method requires a bag as the preliminary container and the bag is made of material conforming to MIL-PRF-121, MIL-PRF-131, or MIL-PRF-22191, type I or II. However, wraps shall not be excluded if necessary to protect the bags from rupture or perforation.

5.2.3.2 Metal surfaces not coated with preservatives. Only noncorrosive wrapping, cushioning and dunnage materials meeting the test requirements of MIL-STD-3010, Test Method 3005, shall be used in contact with metal surfaces of the item. Materials also shall be as dry and clean as practicable at the time of use.

5.2.3.3 Method 10 - Physical protection. The unpreserved item(s) shall be protected from physical damage and mechanical malfunction. Cushioning materials, dunnage, blocking and bracing shall be applied as required to protect the item(s) and the enclosing media and restrict the movement of the item within the container. The materials selected for all blocking and bracing, and the design and application thereof, shall be compatible with the item and its bearing load limitations. Materials shall be as clean and as dry as practicable. Method 10 packs shall pass the applicable inspection requirements of table G-I.

5.2.3.4 Method 20 – Physical protection with preservative (with greaseproof wrap, as required). Items shall be treated with appropriate preservatives in accordance with the procedures of 5.2.2.2 or 5.2.2.3. Contact preservative coated items shall be wrapped in material conforming to MIL-PRF-121 or QQ-A-1876. Flexible wraps shall snugly enclose the coated part or item and be secured to prevent unintentional unwrapping. Parts or items coated with hard film preservatives conforming to MIL-PRF-16173, Grade 1 or 4, may, when dried, be exempted from wrapping. Projections, sharp edges, or other features of the item, which may damage the wrap, shall be cushioned as required in accordance with 5.2.3. The type of cushioning and wrapping material used shall be commensurate with the size, weight and configuration of the preserved part or item. Method 20 packs shall pass the applicable inspection requirements of table G-I. When it has been determined to protect items with VCI, they shall be preserved in accordance with 5.2.4.9.

5.2.3.5 Method 30 - Waterproof or waterproof-greaseproof protection with preservative as required. Items protected in accordance with Method 30 shall be heat sealed within a waterproof or waterproof-greaseproof bag. Projections, sharp edges or other physical characteristics of the item, which may damage the waterproof or waterproof-greaseproof barrier or container shall be cushioned in accordance with 5.2.3. The item shall also be cushioned as required to mitigate shock, thereby preventing physical and functional damage to the item.

Unless otherwise specified, preservative coating requirements shall be determined in accordance with 5.2.2.1. All packs prepared in accordance with any method of this basic group shall pass the applicable quality assurance tests specified in tables G-I and G-II.

5.2.3.5.1 Method 31 - Waterproof bag, heat sealed. The item, preserved, wrapped and cushioned as required in 5.2.3.5, shall be enclosed in a heat sealed bag conforming to MIL-DTL- 117, Type III, Class B, Style 2. When specified, a designated bag, other than noted herein, shall be provided. (Note: When specified in the contract or order, a carton or box shall be required to effect the unit container and the primary cushioning specified in the contract or order shall be placed between the outside of the bag and the inside of the carton or box.) When it has been determined to protect items with VCI, they shall be preserved in accordance with 5.2.4.9.

5.2.3.5.2 Method 32 - Container, waterproof bag, heat sealed. The item, preserved, wrapped and cushioned as required in 5.2.3.5, shall be enclosed in a close fitting container (box) selected from table C-I, which in turn shall be enclosed in a heat sealed waterproof bag conforming to MIL-DTL-117, Type III, Class B, Style 2, or MIL-DTL-117, Type III, Class C, Style 1. When specified, a protective wrap of heavy duty kraft paper or equivalent material (tape sealed) shall be provided to protect the barrier material during handling and storage.

5.2.3.5.3 Method 33 - Greaseproof-waterproof bag, heat sealed. The item, preserved, wrapped and cushioned as required in 5.2.3.5, shall be enclosed in a close fitting heat sealed bag conforming to MIL-DTL-117, Type II, Class C, Style 1, 2 or 3; or Type III, Class C, Style 1.

When specified in the contract or order, a designated bag, other than noted herein, shall be provided. (Note: When specified in the contract or order, a carton or box shall be required to effect the unit container, and the primary cushioning specified in the contract or order shall be placed between the outside of the bag and the inside of the carton or box.) When it has been determined to protect items with VCI, they shall be preserved in accordance with 5.2.4.9.

5.2.3.6 Method 40 - Watervaporproof protection with preservative as required. Items protected in accordance with Method 40 shall be heat sealed within a watervaporproof enclosure.

Projections, sharp edges or other physical characteristics of the item, which may damage the watervaporproof enclosure, shall be cushioned as required in accordance with 5.2.3. The item shall also be cushioned as required to mitigate shock, thereby preventing physical and functional damage to the item. Unless otherwise specified, preservative coating requirements shall be determined in accordance with 5.2.2.1. All packs prepared in accordance with any method of this basic group shall pass the applicable quality assurance tests specified in tables G-I and G-II.

5.2.3.6.1 Method 41 - Watervaporproof bag, heat sealed. The item, preserved, wrapped and cushioned as required in 5.2.3.6, shall be enclosed in a close fitting heat sealed bag conforming to MIL-DTL-117, Type I, Class E, Style 1, 2 or 3; or Type I, Class F, Style 1; or Type II, Class E, Style 1. (Note: For electrostatic protection refer to 5.2.4.1.) When specified in the contract or order, a designated bag, other than noted herein, shall be furnished. (Note: When specified in the contract or order, a carton or box shall be required to complete the unit container and the primary cushioning specified in the contract or order shall be placed between the outside of the bag and the inside of the carton or box.)

5.2.3.6.2 Method 42 - Container, watervaporproof bag, heat sealed, container. The item, preserved, wrapped and cushioned as required in 5.2.3.6, shall be enclosed in a close fitting inner container (box), selected from table C-I,…