MIL-STD-2073-1D.pdf

MIL-STD-2073-1D

15 December 1999

SUPERSEDING

MIL-STD-2073-1C

1 October 1996

DEPARTMENT OF DEFENSE

STANDARD PRACTICE FOR

MILITARY PACKAGING

AMSC N7296 AREA PACK

NOT MEASUREMENT

SENSITIVE

ii

THIS PAGE IS INTENTIONALLY LEFT BLANK

iii

FOREWORD

1. This standard is to be invoked only when procured items are expected to enter the military distribution system. Other items are to be commercially packaged to the extent practicable. Details and decision logic for the use of this standard are described in 1.1, 1.2, figure 1, and 4.1.

2. This military standard is approved for use by all Departments and Agencies of the Department of Defense.

3. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Air Warfare Center Aircraft Division, Highway 547, Code 4.3.5E, Building 562-3, Lakehurst, New Jersey 08733-5049, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.

iv

CONTENTS

Paragraph Page

1. SCOPE

1.1 Purpose

1.1.1 Definition

1.2 Application

1.2.1 Applicability

1.2.2 Non-applicability

2. APPLICABLE DOCUMENTS

2.1 General

2.2 Government documents

2.2.1 Specifications and standards

2.2.2 Other Government documents, drawings and publications

2.3 Non-Government publications

2.4 Order of precedence

3. DEFINITIONS

3.1 General

3.2 Categorization

3.3 Common group items

3.4 Consumable

3.5 Container Design Retrieval System (CDRS)

3.6 Critical items

3.7 Electrostatic Discharge Sensitive (ESDS) items

3.8 Fragility factor

3.9 Hazardous material

3.10 Levels of protection

3.11 Loads

3.12 Packaging design validation

3.13 Prototype pack

3.14 Proper shipping name

3.15 Repairable item

3.16 Reusable container

3.17 Sealed

3.18 Selective group items

3.19 Special group items

v

CONTENTS (Continued)

Paragraph Page

4. GENERAL MILITARY PACKAGING REQUIREMENTS

4.1 General

4.2 Development of military packaging details and data requirements

4.3 Hazardous material

4.4 Packaging of classified items

4.5 Quantity per unit pack (QUP)

4.6 Containers

4.7 Kits

4.8 Repairable excess and residual parts

4.9 Loose fill materials

4.10 Shock and vibration absorption

4.11 Determination of item fragility

4.12 Packaging materials

5. DETAILED MILITARY PACKAGING REQUIREMENTS

5.1 General military package design considerations

5.2 Military preservation

5.2.1 Cleaning and drying

5.2.2 Preservatives

5.2.2.1 Preservative applicability

5.2.2.2 Application of contact preservatives

5.2.2.3 Application and use criteria of volatile corrosion inhibitors (VCI)

5.2.3 Methods of military preservation – general requirements

5.2.3.1 Surfaces coated with preservatives

5.2.3.2 Metal surfaces not coated with preservatives

5.2.3.3 Method 10 (formerly Method III) – Physical protection

5.2.3.4 Method 20 (formerly Method I) – Preservative coating only (with greaseproof wrap, as required)

5.2.3.5 Method 30 (formerly Method IC) – Waterproof or waterproof-greaseproof protection with preservative as required

5.2.3.5.1 Method 31 (formerly Submethod IC-3) – Waterproof bag, sealed

5.2.3.5.2 Method 32 (formerly Submethod IC-2) – Container, waterproof bag, sealed

5.2.3.5.3 Method 33 (formerly Submethod IC-1) – Greaseproof-waterproof bag, sealed vi

CONTENTS (Continued)

Paragraph Page

5.2.3.6 Method 40 (formerly Method IA) – Watervaporproof protection with preservative as required

5.2.3.6.1 Method 41 (formerly Submethod IA-8) – Watervaporproof bag, sealed

5.2.3.6.2 Method 42 (formerly Submethod IA-14) – Container, water-vaporproof bag, sealed, container

5.2.3.6.3 Method 43 (formerly Submethod IA-16) – Floating water-vaporproof bag, sealed

5.2.3.6.4 Method 44 (formerly Submethod IA-13) – Rigid container (other than metal), sealed

5.2.3.6.5 Method 45 (formerly Submethod IA-5) – Rigid metal container, sealed

5.2.3.7 Method 50 (formerly Method II) – Watervaporproof protection with desiccant

5.2.3.7.1 Method 51 (formerly Submethod IIc) – Watervaporproof bag, sealed

5.2.3.7.2 Method 52 (formerly Submethod IIb) – Container, watervapor-proof bag, sealed, container

5.2.3.7.3 Method 53 (formerly Submethod IIa) – Floating watervaporproof bag, sealed

5.2.3.7.4 Method 54 (formerly Submethod IIf) – Rigid container (other than metal), sealed

5.2.3.7.5 Method 55 (formerly Submethod IId) – Rigid metal container, sealed

5.2.4 Military preservation requirements for items with specific characteristics

5.2.4.1 Electrostatic discharge sensitive (ESDS) items

5.2.4.2 Items capable of disassembly

5.2.4.3 Flexible-coilable items

5.2.4.4 Wheeled items

5.2.4.5 Caging or damping

5.2.4.6 Items with mounts

5.2.4.7 Rubber and synthetic rubber items

5.2.4.8 Hazardous items

5.3 Level A and B packing requirements

vii

CONTENTS (Continued)

Paragraph Page

5.3.1 Intermediate containers

5.3.2 Exterior containers

5.3.2.1 Container selection

5.4 Minimal packing requirements

5.5 Marking

5.6 Military packaging design validation provisions

5.7 Quality assurance provisions

6. NOTES

6.1 Acquisition requirements

6.2 Issue of DoDISS

6.3 Associated Data Item Descriptions (DIDs)

6.4 Testing facilities

6.5 Changes in methods of preservation designations

6.6 Subject term (keyword listing)

6.7 Copies of regulations

6.8 Supersession

6.9. Changes from previous issue

FIGURES

Figure Page

1 Military packaging requirements development decision chart

TABLES

Table Page

I Approximate fragility factors II Method of preservation vs. unit container bag material cross reference to MIL-B-117 viii

CONTENTS (Continued)

APPENDICES

APPENDIX A

DEVELOPMENT OF MILITARY PACKAGING REQUIREMENTS

Paragraph Page

A.1 SCOPE

A.2 APPLICABLE DOCUMENTS

A.2.1 General A.2.2 Government documents A.2.2.1 Specifications and standards A.2.2.2 Other Government documents, drawings and publications A.2.3 Non-Government publications

A.3 USE OF EXISTING PACKAGING REQUIREMENTS

A.3.1 Application

A.4 HAZARDOUS MATERIAL

A.4.1 General A.4.2 Hazardous material package testing A.4.3 Hazardous material shipment documentation

A.5 MILITARY PACKAGING CODE DEVELOPMENT

A.5.1 Item classification A.5.2 Item characteristics A.5.3 Categorization A.5.3.1 Category code A.5.3.2 Category code development A.5.3.2.1 First category – physical and chemical characteristics A.5.3.2.1.1 Item composition/properties criteria A.5.3.2.1.2 Critical item criteria A.5.3.2.1.3 Contact preservative criteria A.5.3.2.2 Second category – weight/size/fragility A.5.3.2.3 Third category – preservatives A.5.4 Military packaging codes for common items A.5.5 Military packaging codes for selective items A.5.6 Recording of coded requirements ix

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX A (Continued)

Paragraph Page

A.6 CONTAINER SELECTION

A.7 FORMULAS

A.8 PACKAGING DESIGN VALIDATION

A.8.1 Common items A.8.2 Selective and special items

FIGURES

Figure Page

A.1 Format for interpretation of packaging code sequence

TABLES

Table Page

A.I Physical and chemical characteristics category code determination A.II Weight/size/and non-operational fragility category code determination A.III Contact preservative category code determination A.IV Predetermined military packaging data for common items A.V Formulas for material weight and size calculations A.VI Procedural packaging specifications

APPENDIX B

FACTORS AND FORMULAE ESTABLISHING MILITARY PACKAGING QUP AND ICQ

Paragraph Page

B.1 SCOPE

x

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX B (Continued)

Paragraph Page

B.2 APPLICABLE DOCUMENTS

B.3 DETERMINATION OF QUP

B.3.1 Repairable items (depot or field level) or items designated Hi-value or Hi-priority B.3.2 Consumable items B.3.3 Irregular configuration, delicate or fragile items B.3.4 Pairs and sets items B.3.5 Items unit packed in accordance with Method 50 B.3.6 Kit B.3.7 Lumber, raw stock, paints, oils and dope B.3.8 Factors and formulae establishing QUP B.3.8.1 Consumable items having both maintenance and overhaul applications B.3.8.2 Consumable items having overhaul applications only

B.4 QUANTITY PER UNIT PACK DETERMINATION FORMULAE

B.4.1 Formula A B.4.2 Formula B

B.5 DETERMINATION OF ICQ

B.5.1 Quantities per intermediate container B.5.2 Intermediate container limitations

TABLES

Table Page

B.I Guidance for establishing number of unit packs per intermediate container xi

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX C

CONTAINERS

Paragraph Page

C.1 SCOPE

C.2 APPLICABLE DOCUMENTS

C.2.1 General C.2.2 Government documents C.2.2.1 Specifications, standards and drawings C.2.3 Non-Government publications

C.3 GENERAL

C.3.1 Unit container size C.3.2 Use of unit containers as shipping containers

C.4 EXPENDABLE CONTAINERS

C.4.1 Interior containers C.4.2 Exterior containers

C.5 REUSABLE CONTAINERS

C.5.1 Specialized containers C.5.1.1 Design C.5.1.2 Container Design Retrieval System (CDRS) C.5.1.3 Specialized shipping containers for ordnance C.5.2 Multiapplication containers C.5.2.1 Design and selection C.5.2.2 Identification C.5.2.3 Coded data C.5.2.4 Packaging design validation C.5.2.5 Short life containers C.5.2.6 Long life containers C.5.2.7 Multiapplication container availability C.5.2.7.1 General Services Administration (GSA) C.5.2.7.2 Naval Inventory Control Point (NAVICP) C.5.2.7.3 Commercial sources xii

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX C (Continued)

TABLES

Table Page

C.I Interior containers C.II Exterior shipping containers – selection by maximum weight of contents and level of packing C.III Fiberboard container size list C.IV Multiapplication container selection

APPENDIX D

DEVELOPMENT OF MILITARY PACKAGING REQUIREMENTS

FOR KITS (PARTS AND MODIFICATION)

Paragraph Page

D.1 SCOPE

D.2 APPLICABLE DOCUMENTS

D.3 PRESERVATION

D.3.1 Consolidation of different items within a method of preservation D.3.2 Application of preservative compounds or oils D.3.2.1 Kits procured for oxygen equipment D.3.2.2 Preservation procedures D.3.2.3 Items susceptible to corrosion (iron, steel, magnesium, etc.)

D.4 UNIT PRESERVATION

D.4.1 Physical protection D.4.2 Segregation of items within packs D.4.3 Skin packaging D.4.3.1 Skin packaging metals D.4.3.2 Skin packaging shims or gaskets

D.5 PACKING AND MARKING OF KITS

xiii

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX E

MILITARY PACKAGING DATA FORMS

Paragraph Page

E.1 SCOPE

E.2 APPLICABLE DOCUMENTS

E.2.1 General E.2.2 Government documents E.2.2.1 Standards

E.3 GENERAL REQUIREMENTS

E.3.1 Development of military packaging data E.3.2 Recording military packaging data E.3.2.1 Manual recording of data E.3.2.2 National Stock Number (NSN) requirements E.3.2.3 Coded data E.3.2.4 Kits (Parts and Modification) E.3.2.5 Special packaging instructions

E.4 DETAILED REQUIREMENTS

E.4.1 Development of military packaging data E.4.1.1 Procedural specification data E.4.2 Preparation of military packaging data E.4.2.1 Nomenclature E.4.2.2 Manufacturer's Commercial and Government Entity code and part number E.4.2.3 Configuration item (CI) E.4.2.4 Item identification data E.4.2.5 Preservation and packing data E.4.2.6 Supplemental data E.4.2.7 Special packaging instruction (SPI) data

E.5 PREPARATION OF SPECIAL PACKAGING INSTRUCTION (SPI) ..99

E.5.1 General xiv

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX E (Continued)

Paragraph Page

E.5.2 Format E.5.2.1 SPI preparation instructions E.5.2.2 Details of completion of SPI E.5.2.2.1 Additional information E.5.2.2.2 Details E.5.2.2.3 Materials E.5.2.2.3.1 Lumber and plywood E.5.2.2.3.2 Fiberboard E.5.2.2.3.3 Isolation system E.5.2.2.3.4 Hardware E.5.2.2.4 Specification containers E.5.2.2.5 Trade names E.5.2.2.6 Application of additional items E.5.2.3 Styles E.5.2.4 Variations in style and format

E.6 APPROVAL OF CONTRACTOR DEVELOPED PACKAGING

DATA

E.6.1 Procedures for submitting data for approval E.6.1.1 Approval of data without National Stock Numbers E.6.1.2 Approval of data for emergency shipments E.6.1.3 Approval of data of interest to one DoD agency E.6.1.4 Use of background data for approval E.6.1.5 Return of approved data E.6.1.5.1 Authentication E.6.1.6 Data for common items E.6.2 Transmittal of data E.6.2.1 Preservation and packing data E.6.2.2 Special packaging instructions E.6.2.2.1 Computerized format E.6.2.3 Method of transmission xv

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX E (Continued)

TABLES

Table Page

E.I Item identification data for PART A of DD Form 2326 E.II Preservation – Packing data for PART B of DD Form 2326 E.III Supplemental data for PART C of DD Form 2326 E.IV Special packaging instruction data for PART D of DD Form 2326

FIGURES

Figure Page

E.1 Preservation and Packing Data E.2 Special Packaging Instruction

APPENDIX F

MILITARY PACKAGING DESIGN VALIDATION PROVISIONS

Paragraph Page

F.1 SCOPE

F.2 APPLICABLE DOCUMENTS

F.2.1 General F.2.2 Government documents F.2.2.1 Standards F.2.2.2 Other Government documents F.2.3 Non-Government publications

F.3 GENERAL

F.3.1 Packaging design validation tests F.3.2 Hazardous material F.3.3 Ammunition unit loads xvi

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX F (Continued)

Paragraph Page

F.4 TEST METHODS

F.4.1 Container performance tests F.4.2 Preservation tests

F.5 OTHER

F.5.1 Acceptance criteria and disposition of test samples

APPENDIX G

QUALITY ASSURANCE PROVISIONS

Paragraph Page

G.1 SCOPE

G.2 APPLICABLE DOCUMENTS

G.2.1 General G.2.2 Government documents G.2.2.1 Specifications and standards

G.3 GENERAL

G.3.1 Quality system G.3.2 Quality assurance requirements G.3.3 Sampling G.3.3.1 Lot size G.3.3.2 Sampling for inspection

G.4 PRESERVATION INSPECTIONS

G.4.1 Visual preservation examinations G.4.2 Leakage test G.4.2.1 Wetting agent G.4.2.2 Selection of technique G.4.2.2.1 Vacuum retention technique G.4.2.2.1.1 Sealed rigid container xvii

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX G (Continued)

Paragraph Page

G.4.2.2.1.2 Sealed flexible bag G.4.2.2.2 Submersion (or immersion) technique G.4.2.2.3 Pneumatic pressure technique G.4.2.2.4 Hot water technique G.4.2.2.5 Squeeze technique (applicable only to flexible specimens) G.4.3 Heat-sealed seam test G.4.3.1 Selection of samples for heat-sealed seam tests G.4.3.1.1 Alternate sampling procedure for heat-sealed seam test G.4.3.2 Performance of heat-sealed seam test

G.5 PACKING INSPECTIONS

G.5.1 Examination procedures

TABLES

Table Page

G.I Preservation inspection provisions G.II Leakage and heat-sealed seam test provisions

APPENDIX H

PROCEDURES FOR COMPLIANCE WITH CONTAINER DESIGN

RETRIEVAL SYSTEM (CDRS) REQUIREMENTS

Paragraph Page

H.1 SCOPE

H.2 APPLICABLE DOCUMENTS

H.3 DETAILED REQUIREMENTS

H.3.1 Design search request submittal H.3.2 CDRS/MO search response xviii

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX H (Continued)

Paragraph Page

H.3.3 Design activity action on CDRS/MO response H.3.3.1 Negative response from CDRS/MO H.3.3.1.1 Submittal of container design data H.3.3.2 Positive response from CDRS/MO H.3.3.2.1 Item (Inventory) manager notification H.3.3.2.2 Container design agent notification

APPENDIX J

MILITARY PACKAGING REQUIREMENT CODES

Paragraph Page

J.1 SCOPE

J.2 APPLICABLE DOCUMENTS

J.2.1 General J.2.2 Government documents J.2.2.1 Specifications, standards and handbooks J.2.2.2 Other Government documents, drawings and publications J.2.3 Non-Government publications

J.3 GENERAL REQUIREMENTS

J.3.1 Code system J.3.2 Procedure and responsibilities for revisions J.3.2.1 Adding codes

J.4 DETAILED REQUIREMENTS

J.4.1 General code requirements J.4.2 Preservation methods J.4.2.1 Specialized preservation J.4.3 Quantity per unit pack J.4.4 Cleaning xix

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX J (Continued) Paragraph Page

J.4.5 Preservative J.4.6 Wrapping material J.4.7 Cushioning and dunnage J.4.8 Thickness of cushioning or dunnage J.4.9 Unit and intermediate container J.4.9.1 Options J.4.10 Unit container level and optional procedure indicator codes J.4.11 Unit packs per intermediate container J.4.12 Intermediate container J.4.12.1 Intermediate container limitations J.4.13 Packing J.4.14 Special markings

J.5 CROSS INDEX

J.5.1 Document number to table and code

TABLES

Table Page

J.I Methods of preservation codes J.Ia Specialized preservation codes J.II Cleaning procedure codes J.III Contact preservative material codes J.IIIa Contact preservative material codes in specification sequence J.IV Wrapping material codes J.IVa Wrapping material codes in specification sequence J.V Cushioning and dunnage material codes J.Va Cushioning and dunnage material codes in specification sequence J.VI Thickness of cushioning or dunnage codes J.VII Unit and intermediate container codes J.VIIa Unit and intermediate container codes in specification sequence J.VIII Unit container level codes xx

CONTENTS (Continued) APPENDICES (Continued)

APPENDIX J (Continued) TABLES (Continued)

Table Page

J.VIIIa Optional procedure indicator codes J.IX Military packing requirement codes J.IXa Minimal packing requirement codes J.X Special marking codes J.XI Document number to table and code cross-reference index

INDEX

1. SCOPE

1.1 Purpose. This document outlines standard processes for the development and documentation of military packaging, as distinct from commercial packaging. This standard covers methods of preservation to protect materiel against environmentally induced corrosion and deterioration, physical and mechanical damage, and other forms of degradation during storage, multiple handling, and shipment associated with the military distribution system. A decision chart is included for developing these packaging requirements (see figure 1).

1.1.1 Definition. For purposes of this standard, military distribution system is defined as the process(es) by which materiel, not intended for immediate use, is stored or moved within or between DoD facilities.

1.2 Application.

1.2.1 Applicability. The requirements of this standard apply to:

a Items expected to enter the military distribution system

b. Items delivered during wartime

c. Items requiring reusable containers

d. Items intended for delivery-at-sea

1.2.2 Non-applicability. Items not going into the military distribution system are to be packaged in accordance with commercial practice. This includes, but is not limited to, the following:

a. Items intended for immediate use

b. Items for not-mission-capable supply

c. Items intended for depot operational consumption

d. Small parcel shipments (CONUS), not-for-stock

e. Direct vendor deliveries (CONUS)

Is item entering the * military distribution system? (See 1.2)

Are there existing adequate military packaging requirements for the item?

Use existing requirements.

(See A.3.1) Is item hazardous?

Package IAW A.4Is item consumable?

Is item fragility factor less than 50 G's?

Is item fragility factor equal to or grater than 85 G's?

(See 3.8 and Table I)

Are item weight & dimensions within limits specified by Table A.II?

Categorize IAW Appendix A as common item

Can item packaging be described by codes in Appendix

J and supplemental data?

Select Appendix J codes and add supplemental data, as req'd

(selective item); (See 5.6 for validation requirement)

Is specialized long life container required?

(See C.5)

Interrogate Container Design

Retrieval System (CDRS)

(See C.5.1.2)

Is CDRS response positive?

Use design "AS IS" or modify if required.

Determine availability of suitable containers in

DoD inventory for reuse

Design package using special packaging instruction (SPI) format specified in Appendix E

(See 5.6 for validation requirements)

Package and ship IAW commercial practices.

(ASTM-D3951)

Are item weight, dimensions and fragility factor within limits specified for containers listed in

Table C. IV?

Are item weight and dimensions within limits specified for containers listed in

Table C. IV?

Do multi-application containers meet logistic needs?

Could items of lower or unknown fragility be protected by multi-application containers? (See

Table C. IV)

Is it cost effective to use multi-application containers?

Will 10 trip short life container meet logistics needs? Can item packaging be described by codes in

Appendix J and supplemental data, as req'd?

Use 10 trip short life container

(See C.5.2.5)

Will 100 trip long life container meet logistics needs?

Use 100 trip long life container

(See C.5.2.6)

Select Appendix J codes

IAW Appendix A format

(See 5.6 for validation requirements)

YES

NO YES

YES NO

YES NO

NO NOYES YES

NOYES

NOYES

YES YES NONO

YES NO

YES NO

YES NO

YES NO

NO

YES NO

* This decision is to be made by the DOD contracting activity (packaging organization) prior to RFQ or solicitation.

YES NO

YES NO

NO YES

FIGURE 1. Military packaging requirements development decision chart.

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this standard. This section does not include documents cited in other sections of this standard or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3, 4, and 5 of this standard, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2).

SPECIFICATIONS

FEDERAL

A-A-3174 - Plastic Sheet, Polyolefin.

QQ-A-1876 - Aluminum Foil.

PPP-B-1672 - Box, Shipping, Reusable with Cushioning.

MILITARY

MIL-B-117 - Bags, Sleeves and Tubing.

MIL-B-121 - Barrier Material, Greaseproofed, Waterproofed, Flexible.

MIL-PRF-131 - Barrier Materials, Watervaporproof, Greaseproof, Flexible, Heat-Sealable.

MIL-PRF-3420 - Packaging Materials, Volatile Corrosion Inhibitor

Treated, Opaque.

MIL-D-3464 - Desiccants, Activated, Bagged, Packaging Use and Static

Dehumidification.

MIL-E-6060 - Envelope, Packaging, Water-Vaporproof, Flexible.

MIL-I-8574 - Inhibitors, Corrosion, Volatile, Utilization of.

MIL-PRF-16173 - Corrosion Preventive Compound, Solvent Cutback, Cold-Application.

MIL-PRF-22019 - Barrier Materials, Transparent, Flexible, Sealable, Volatile Corrosion Inhibitor Treated.

SPECIFICATIONS (continued)

MILITARY (continued)

MIL-B-22020 - Bags, Transparent, Flexible, Sealable, Volatile Corrosion Inhibitor Treated.

MIL-PRF-22191 - Barrier Material, Transparent, Flexible, Heat Sealable.

MIL-I-26860 - Indicator, Humidity, Plug, Color Change.

MIL-PRF-81705 - Barrier Materials, Flexible, Electrostatic Protective, Heat

Sealable.

STANDARDS

FEDERAL

FED-STD-101 - Test Procedures for Packaging Materials.

MILITARY

MIL-STD-129 - Marking for Shipment and Storage.

MIL-STD-1186 - Cushioning, Anchoring, Bracing, Blocking and

Waterproofing; With Appropriate Test Methods.

MS20003 - Indicator, Humidity, Card, Three Spot, Impregnated

Areas (Cobaltous Chloride).

(Unless otherwise indicated, copies of the above specifications and standards are available from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2.2 Other Government documents, drawings and publications. The following other Government documents, drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation.

MANUAL

DoD-5220.22M - Industrial Security Manual for Safeguarding Classified Information.

CODE OF FEDERAL REGULATIONS (CFR)

29 CFR - Labor.

40 CFR - Protection of Environment.

49 CFR - Transportation.

(Application for copies should be addressed to the Superintendent of Documents, U.S Government Printing Office, North Capital & H Streets, N.W., Washington, DC 20402.)

2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation.

Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2).

AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)

ASTM-D996 - Standard Terminology of Packaging and Distribution Environments (DoD adopted).

ASTM-D1008 - Test Methods for Water Vapor Transmission of Shipping Containers (DoD adopted).

ASTM-D1974 - Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes (DoD adopted).

ASTM-D3951 - Standard Practice for Commercial Packaging (DoD adopted).

ASTM-D5118 - Fabrication of Fiberboard Shipping Boxes.

ASTM-D5168 - Fabrication and Closure of Triple Wall Corrugated Fiberboard

Containers (DoD adopted).

ASTM-D5330 - Tape, Pressure Sensitive, Packaging Filament Reinforced.

(Application for copies should be addressed to the American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.)

2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

3. DEFINITIONS

3.1 General. Definitions of terms unique to this standard are listed below. Definitions of other terms commonly used in the packaging community may be found in ASTM-D996.

3.2 Categorization. The process of evaluating an item by chemical and physical characteristics that are significant in determining the preservation requirements.

3.3 Common group items. Items with a fragility rating of 85 G's (see 3.8) or more which have no dimension greater than 24 inches and weigh not more than 10 pounds for which predetermined packaging has been developed (see A.5.4 and table A.IV). Hazardous materials, electrostatic discharge sensitive items, shelf life items, sets, and kits are excluded from this group regardless of their fragility, size, or weight.

3.4 Consumable. An item of supply (except explosive ordnance, major end items of equipment, and repairables) that is normally expended or used up beyond recovery in the use for which it was designed or intended.

3.5 Container Design Retrieval System (CDRS). A management system program to provide a DoD centralized automated data base system for storing, retrieving and analyzing existing container designs and test information concerning specialized containers. The purpose of the CDRS is to avoid duplication in container designs, minimize the number of new container designs being developed and promote reuse of existing DoD specialized containers for new item development and procurement (see Appendix H).

3.6 Critical items. Items meeting one or more of the following criteria are considered critical.

a. Critical chemically. Items which are of such a nature that any degree of deterioration (in the form of corrosion, stain, scale, mold, fungi, or bacteria) caused by oxygen, moisture, sunlight, living organisms, and other contaminants which are time or temperature dependent, will result in premature failure or malfunction of the item or equipment in which the item is installed or with which the item interfaces.

b. Critical physically. Items that would become unfit for use as a result of physical action on the item or any integral surfaces thereof. This includes, but is not limited to items having a surface finish of 64 microinches root mean square or less, items which have surfaces that mate with surfaces of other parts, optical and reflective devices having highly polished surfaces, items requiring a high degree of cleanliness, and items requiring special protection against shock, vibration, or abrasion.

c. Critical application. Items that, either in assembly or operation, provide an essential attribute to attaining critical military objectives.

3.7 Electrostatic Discharge Sensitive (ESDS) items. Electronic items which are susceptible to damage or degradation as a result of an electrostatic discharge event.

3.8 Fragility factor. Maximum force acceleration or deceleration expressed in units of gravity (G's) that can be applied to an item in its non-operating state without causing physical damage or changes in its operational characteristics. The fragility factor is expressed in units of acceleration for a defined shock pulse. Shock pulse forms and durations which approximate the transportation and handling environment is to be used in determining the fragility factor (see table I).

3.9 Hazardous material. A material, substance, or waste which has been determined by the Secretary of Transportation to be capable of posing an unreasonable risk to health, safety, and property when transported in commerce and which has been so designated. (This includes all items listed as hazardous in Titles 29, 40 and 49 CFR and other applicable modal regulations effective at the time of shipment.)

3.10 Levels of protection. A means of specifying the level of military preservation and packing that a given item requires to ensure that it is not degraded during shipment and storage.

Specific levels of protection are as follows:

a. Military level of preservation. Preservation designed to protect an item during shipment, handling, indeterminate storage, and distribution to consignees worldwide.

b. Military levels of packing.

(1) Level A. Protection required to meet the most severe worldwide shipment, handling, and storage conditions. A Level A pack must, in tandem with the applied preservation, be capable of protecting material from the effects of direct exposure to extremes of climate, terrain, and operational and transportation environments. Examples of situations which indicate a need for use of a Level A pack are: War Reserve Material, mobilization, strategic and theater deployment and employment, open storage, and deck loading. Examples of containers used for Level A packing requirements include, but are not limited to, overseas type wood boxes, and plastic and metal reusable containers.

(2) Level B. Protection required to meet moderate worldwide shipment, handling, and storage conditions. A Level B pack must, in tandem with the applied preservation, be capable of protecting material not directly exposed to extremes of climate, terrain, and operational and transportation environments. Examples of situations which indicate a need for use of a Level B pack are: security assistance (for example, Foreign Military Sales (FMS)) and containerized overseas shipments. Examples of containers used for Level B packing requirements include, but are not limited to, domestic wood crates, weather-resistant fiberboard containers, fast pack containers, weather-resistant fiber drums, and weather-resistant paper and multi-wall shipping sacks.

3.11 Loads. Types of loads are determined by the degree of structural strength supplied to the shipping container by the contents. Loads are classified as Type 1, easy loads; Type 2, average loads; and Type 3, difficult loads, as described below:

a. Type 1, easy load. A Type 1, easy load, is developed from an item which completely fills the outer shipping container or from items of moderate density prepackaged in an interior container which completely fill the outer shipping container. Easy load items are not easily damaged by puncture or shock and do not shift or otherwise move within the package. Examples include items packaged in boxes or cans which are prepackaged in fiberboard boxes prior to overpacking in the shipping container; chests; tool kits; and sturdy instruments which are fully in contact with, and support, all faces of the shipping container.

b. Type 2, average load. A Type 2, average load, is developed from item(s) of moderately concentrated weight which are packed directly into the shipping container and provide partial support to all panels thereof. It also includes item(s) prepackaged by wrapping or by positioning in partitions, cells or paperboard boxes, or by other means which provide support to all panels of the shipping container.

Examples include items packaged in boxes or cans which are not prepackaged in an interior container; bottles individually separated one from the other by cells or partitions.

c. Type 3, difficult load. A Type 3, difficult load is developed from item(s) which require a high degree of protection to prevent puncture, shock, or distortion of the shipping container. It also includes item(s) which do not provide complete support to the panels of the shipping container. Examples include wrenches, long bolts, and rods which exert concentrated forces on the shipping container; motors, telephones, typewriters, drop forgings, rivets, hardware, or other items that are random packed in bulk; and fragile or delicate items requiring special protection.

3.12 Packaging design validation. Testing to ascertain the capability of the prototype pack to protect the integrity and serviceability of the item(s) for which the package is designed.

3.13 Prototype pack. A preproduction pack designed and constructed to meet specified requirements and which is the model for production packaging.

3.14 Proper shipping name. The name of the hazardous material shown in Roman print (not italics) in part 172.101 of Title 49 CFR or the applicable modal regulations.

3.15 Repairable item. An item which, by the application of engineering, economic, and other factors, could be reasonably restored to a serviceable condition through regular repair procedures.

3.16 Reusable container. A shipping and storage container that can be reused without impairment of its protective function and which can be repaired or retrofitted to prolong its life or modified to adapt it for shipment of items other than that for which it was originally intended.

Reusable shipping and storage containers are further defined as follows:

a. Long life container (100 trips minimum). A shipping container that can be used repeatedly, and whose service life can be expected to equal the service life of the item it is designed to protect. These containers may be refurbished by appropriate maintenance practices to their original condition and subsequently reused.

b. Short life container (10 trips minimum). A shipping container that can be reused for a limited number of times. The container is usually made of wood, plywood, fiberboard or similar material that has a limited life.

c. Multiapplication containers. Multiapplication containers are designed to protect a variety of components within a given fragility and size range. They can be manufactured in a similar manner to that used for specialized containers or in accordance with applicable/specified military or federal specifications. A multiapplication container can be either of the short-life or long-life variety. Short life multiapplication containers include "fast packs," consisting of a family of standard size cushioned fiberboard shipping containers of four types. These types are fully described in PPP-B-1672 and are identified as Types I, II, III and IV in table C.IV. Long-life multiapplication reusable containers are designated as Types

VI thru X and are also described in table C.IV. These containers are made of rugged plastic construction containing internal cushioning pads or permanent shock mitigation systems (for example, shear mounts, steel coils, and springs.) and are designed to protect repairable components packaged therein, during forward and retrograde movements within the military supply system.

d. Specialized container. Specialized containers are generally the long-life variety and are uniquely configured to support and protect a specific item, or limited variety of items, during handling and storage or to protect personnel and equipment from hazardous contents. Containers of this type frequently incorporate energy absorbing systems, temperature control systems or special features to make handling or shipment possible, easier or safer. Engineering drawings, or equivalent, are used to define form, fit, function, materials, tolerances and manufacturing techniques.

Internal fixtures and other fitments within specialized shipping containers result from either original design efforts or the redesign or modification of an existing container to meet a specific application or need.

3.17 Sealed. An item is considered sealed if the entrances to the interior of the item are sealed with gaskets or closely mated surfaces under mechanical pressure or are sealed by threaded closure devices (except plastic caps). Sealed items also include assemblies which are encapsulated in plastics, ceramics, glass or metal with completely cemented seams or joints closing the interior to the entrance of liquid water. Hermetic sealing is a seal that will exclude air and will be leakproof at ambient temperatures and atmospheric pressures and is usually glass to glass, metal to metal or metal to glass.

3.18 Selective group items. Items that cannot appropriately utilize predetermined packaging developed for common group items (see 3.3) yet do not require a drawing, sketch, illustration or separate narrative type instruction to specify packaging details.

3.19 Special group items. Items with peculiar characteristics such as weight, configuration, complexity, fragility, or other considerations that cannot be classified as common or selective. An item is considered special if drawings, sketches, illustrations, narrative type instructions or specialized containers are required to specify packaging details.

4. GENERAL MILITARY PACKAGING REQUIREMENTS

4.1 General. Military packaging requirements shall be developed using the figure 1 decision chart in accordance with the requirements of this section, Section 5 and all Appendices herein. The developed military packaging requirements shall be documented in accordance with Appendix E and as specified on the Contract Data Requirements List (CDRL) (see 6.3). These requirements are generally defined by a twelve digit position-sensitive code system, as illustrated in figure A.1. Appropriate codes are drawn from those listed in Appendix J. When an item has been determined to be in the special group category, a Special Packaging Instruction shall be required, prepared in accordance with Appendix E and as specified on the CDRL (see 6.3).

4.2 Development of military packaging details and data requirements. If this standard is cited for use and no specific military packaging details or data requirements are contained in the contract, the contracting officer shall be contacted for same. Appendix A and other applicable sections and appendices of this standard shall be used to develop detailed military packaging requirements in cases where the development of packaging data by the contractor is cited.

4.3 Hazardous material. Packaging for hazardous materials shall be developed in accordance with the requirements detailed in A.4.

4.4 Packaging of classified items. Packaging developed for classified items shall meet the requirements of DoD 5220.22M, Industrial Security Manual for Safeguarding Classified Information.

4.5 Quantity per unit pack (QUP). The QUP shall be determined in accordance with Appendix B.

4.6 Containers. Requirements for containers and their selection for military packaging applications are detailed in Appendix C.

4.7 Kits. Military packaging of parts kits or modification kits shall be in accordance with Appendix D.

4.8 Repairable excess and residual parts. Repairable excess and residual part(s) for which packaging has not been stipulated by the acquisition activity shall be packaged to afford adequate protection as required to prevent further deterioration due to rust, corrosion, or physical damage.

Unless otherwise specified by the acquisition activity, the QUP shall be one.

4.9 Loose fill materials. Loose fill materials are prohibited in all military packages.

4.10 Shock and vibration absorption. Shock and vibration absorption shall be provided by cushioning materials or devices that adequately protect the contents and packaging components from physical damage during handling, shipment and storage. A cushioning medium shall be placed as close to the contents as practicable. A noncorrosive wrap shall be placed between the item and all corrosive type cushioning media.

4.11 Determination of item fragility. Fragility factors in the non-operating state of the item, established in the item specification, shall be used to establish the maximum energy permitted to reach the item during transportation and handling. When fragility factors are not available or established, criteria of table I can be used to approximate G factors. Caution shall be taken to ensure that there are no additional components installed which lower the item fragility rating.

4.12 Packaging materials. The use of new or commercially available packaging materials or products is encouraged and recommended provided they are equal to or better than similar approved materials or products without increasing the overall cost to the government. To expedite the use of these materials prior to their inclusion in government specifications, their prompt use will be permitted under conditions outlined herein. In instances where the material or product is not covered by a specific specification or standard, the manufacturer or fabricator of the material or product shall make available documented evidence by an approved testing laboratory, that the material or product meets or exceeds all performance requirements of the specification for a similar material or product. The request for approval shall be submitted to the acquisition activity via the technical packaging element of the contract management activity.

5. DETAILED MILITARY PACKAGING REQUIREMENTS

5.1 General military package design considerations. Military packaging shall be of minimum cost consistent with required performance. Unit packs shall be designed to conserve weight and cube while retaining the protection required and enhancing standardization.

5.2 Military preservation. The military preservation procedure should be accomplished without interruption. When interruptions are unavoidable, temporary wraps, covers or enclosures shall be provided to insure against contamination or deterioration of the items.

5.2.1 Cleaning and drying. Items shall be cleaned and dried by any suitable process or processes which are not injurious to the item. All items shall pass the applicable cleaning and drying inspection requirements of table G.I.

5.2.2 Preservatives.

5.2.2.1 Preservative applicability. When contact preservatives are required to protect an item from chemical deterioration, they shall conform to table J.III. Preservatives selected shall be those whose application, use, or removal will not damage the item or impair item function.

5.2.2.2 Application of contact preservatives. Directly after cleaning and drying of the item, the required preservative shall be uniformly applied by any appropriate procedure that permits the preservative to coat all necessary surfaces. Suggested methods of application include, but are not limited to:

a. Dipping

b. Flow coating

c. Slushing

d. Brushing

e. Filling or flushing

f. Fogging

g. Spraying

5.2.2.3 Application and use criteria of volatile corrosion inhibitors (VCI). Volatile corrosion inhibitor preservative treatment shall be applied in accordance with the criteria and procedures of MIL-I-8574.

5.2.3 Methods of military preservation - general requirements. There are five basic methods of preservation (MOP) defined herein:

Method 10 (formerly Method III) Physical protection Method 20 (formerly Method I) Preservative coating only Method 30 (formerly Method IC) Waterproof protection Method 40 (formerly Method IA) Watervaporproof protection Method 50 (formerly Method II) Watervaporproof protection with desiccant

Various specific techniques, also defined herein, have been developed to meet the basic Methods 30, 40, and 50 which may be used as appropriate. The preservation methods shall be as specified in the contract or purchase order. In the absence of such requirements, the appropriate method shall be selected in accordance with the applicable tables of Appendix A. The following general requirements will apply:

a. Protection from physical damage and mechanical malfunction is required for all methods of preservation in addition to the specific environment protection provided.

b. When methods provide either transparent or opaque protection, transparent protection may be furnished at the option of the supplier but is not required unless specifically called for in the contract or purchase order.

c. Protection for all electrostatic discharge sensitive items requires the use of packaging materials to counteract electrostatic and electromagnetic field forces (see 5.2.4.1).

d. When specific methods require using a bag or container, preliminary wrapping, cushioning or other dunnage material shall be applied as necessary to protect the item, the bag, and the container from all projections or sharp edges of the item as well as to restrict movement of the item within the unit pack.

e. When methods require chipboard or fiberboard containers within the bag, the corners and edges of the containers shall be blunted prior to placing the item in the box and enclosing within the bag.

f. When a transparent unit pack is specified, the preliminary wrapping shall also be transparent. Items preserved with VCI-treated materials are exempted from preliminary wrapping.

g. Methods of preservation requiring the use of a bag for the interior packaging shall be subject to the use and fabrication procedures and limitations of MIL-B-117.

Table II lists the acceptable materials that may be used in constructing bags that meet the requirements of these specific methods of preservation. Bags shall comply with MIL-E-6060 when the construction limitations of MIL-B-117 are exceeded.

h. All cushioning and dunnage used shall be as clean and dry as practicable to minimize item susceptibility to corrosion and contaminants.

i. Items with handles, knobs or other protrusions shall be wrapped or otherwise protected and secured to facilitate equal distribution of shock forces over the entire surface of the item and thus prevent damaging shock forces to the protrusion.

j. When flexible bags are used, the volume of trapped air within the bag shall be kept to a minimum by compressing the bag around the contents, or by carefully drawing a vacuum inside the bag, prior to final sealing. Caution shall be taken to prevent rupture of the bag.

5.2.3.1 Surfaces coated with preservatives. Preliminary wrapping materials in contact with any item coated with a preservative shall be greaseproof and shall conform to MIL-B-121, Grade A, or QQ-A-1876. Greaseproof wraps applied solely to confine the contact preservative on item surfaces are not necessary when a method requires a bag as the preliminary container and the bag is made of material conforming to MIL-B-121, Grade A, MIL-PRF-131, or MIL-PRF-22191, Type I or II. However, wraps shall not be excluded if necessary to protect the bags from rupture or perforation.

5.2.3.2 Metal surfaces not coated with preservatives. Only noncorrosive wrapping, cushioning and dunnage materials meeting the test requirements of FED-STD-101, Test Method 3005, shall be used in contact with metal surfaces of the item. Materials also must be as dry and clean as practicable at the time of use.

5.2.3.3 Method 10 (formerly Method III) - Physical protection. The unpreserved item(s) shall be protected from physical damage and mechanical malfunction. Cushioning materials, dunnage, blocking and bracing shall be applied as required to protect the item(s) and the enclosing media and restrict the movement of the item within the container. Materials shall be as clean and as dry as practicable. Blocking and bracing shall be accomplished in accordance with MIL-STD- 1186. Method 10 packs shall pass the applicable inspection requirements of table G.I.

5.2.3.4 Method 20 (formerly Method I) - Preservative coating only (with greaseproof wrap, as required). Items shall be treated with appropriate preservatives in accordance with the procedures of 5.2.2.2 or 5.2.2.3. Contact preservative coated items shall be wrapped in material conforming to MIL-B-121, Grade A, or QQ-A-1876. Flexible wraps shall snugly enclose the coated part or item and be secured to prevent unintentional unwrapping. Parts or items coated with hard film preservatives conforming to MIL-PRF-16173, Grade 1 or 4, may, when dried, be exempted from wrapping. Items preserved with VCI treated materials conforming to MIL-PRF-3420 or MIL-PRF-22019, respectively taped or sealed to form an airtight enclosure, are also exempted from wrapping. Projections, sharp edges, or other features of the item, which may damage the barrier wrap, shall be cushioned as required in accordance with 5.2.3. The type of cushioning and barrier material used shall be commensurate with the size, weight and configuration of the preserved part or item. Method 20 packs shall pass the applicable inspection requirements of table G.I.

5.2.3.5 Method 30 (formerly Method IC) - Waterproof or waterproof-greaseproof protection with preservative as required. Items protected in accordance with Method 30 shall be sealed within a waterproof or waterproof-greaseproof bag. Projections, sharp edges or other physical characteristics of the item, which may damage the waterproof or waterproof-greaseproof barrier or container shall be cushioned in accordance with 5.2.3. The item shall also be cushioned as required to mitigate shock, thereby preventing physical and functional damage to the item. Unless otherwise specified, preservative coating requirements shall be determined in accordance with 5.2.2.1. All packs prepared in accordance with any method of this basic group shall pass the applicable quality assurance tests specified in tables G.I and G.II.

5.2.3.5.1 Method 31 (formerly Submethod IC-3) - Waterproof bag, sealed. The item, preserved, wrapped and cushioned as required in 5.2.3.5, shall be enclosed in a sealed bag conforming to MIL-B-117, Type I, Class B, Style 2, or MIL-B-22020 as limited by MIL-I-8574.

When specified, a designated bag, other than noted herein, shall be provided. (Note: When specified in the contract or purchase order, a carton or box shall be required to effect the unit container and the primary cushioning specified…