Attach_3,_System_Specs.DOC

SYTEM SPECIFICATIONS

Installation to be accomplished by a factory trained and approved installation team experienced in installation of the manufacturer's mobile storage system.

Warrantees: Shelving system, storage units and racks to carry a lifetime warranty from the date of final installation.

Mobile system and moving parts to be warranted against defective parts and workmanship for a period of one year from the date of final installation.

SYSTEM SPECIFICATIONS

GENERAL STANDARD SYSTEM SPECIFICATIONS

Standard system using V –shaped triangular common post system

9,000 pound per post capacity

Shelves adjust on 1-1/2 increments using tapered slots

Capable of double and triple decking

Capable of inserting wire and solid shelves

Capable of inserting wide modular drawers with 200-400 pound capacity, 36" or 48" wide

Capable of adding lockable doors

Capable of post interchange with shelving and bulk rack system

EQUIPTO CS112038 OR EQUAL MOBILE AISLE FOR USE WITH STANDARD SYSTEM

System Capable of supporting a minimum of 1000 pounds per linear foot of carriage

Must contain a non-grouted substructure Re-levelable floor system to adjust to uneven surfaces.

Wheels are coiled rolled steel, maintenance free, double flanged for support and weight distribution.

Deck material (infill) ¾” tongue and groove plywood, coated with a high-density polyethylene overlay wear layer.

Aisle safety lock preventing the unit from being closed when aisle is in use.

No form floor breaking should be required with the mobile system.

Systems ending with rolling ranges require an end stop at the end of each track in the system.

Full end and sidewall panels.

The entire system must be a “turn key" design.

Mechanical Assist Mobile Carriage with driveshaft/gear chain system.

TECHNICAL SPECIFICATION STANDARD SHELVING

Standard "V" shaped double flanged upright shelving units must be designed so as to accommodate wide rolling drawers, lockable door fronts, wire and/or steel shelving, wire and/or steel dividers, bin fronts and/or steel sliding drawers for current utilization or for future storage expansion requirements. Units must have the flexibility of installation with bulk rack and with double entry shelving capable of side by side (common upright) installation with the system. All components and compatible fixtures must maintain engineering consistency and must color match.

Solid Steel Uprights 16-gauge cold rolled steel, rolled into a wide hollow "V" shape. Uprights shall be indexed on 6” centers for easy shelf location.

Solid Steel Panels

End Panels

Front and back vertical posts are joined with 22-gauge cold rolled steel sheet that provides a closed end/or center panel for shelving units Back Panels

Back and vertical posts are joined with 24-gauge cold roll steel sheet that provides a closed back for shelf units.

Shelving

a) Heavy Duty Solid Steel Shelf

Shelf to be adjustable from the front without tools. Load capacities from 650 to 700 pounds (depending on shelf width) per shelf (uniformly distributed).

b) Reinforced Heavy Duty Solid Steel Shelf

Shelf to be adjustable from the front without tools. Load capacities from 700 to 1,170 pounds (depending on shelf width) per shelf (uniformly distributed).

c) Wire Shelving

Steel wire shelving with "V" shaped wire trusses, Shelf to be adjustable from the front without tools. Load capacity to 700 pounds per shelf (uniformly distributed).

Steel Sliding Drawers

24 gauge cold roll, fold form steel sliding drawers painted inside and out, with steel handles. Drawers are designed to be placed directly on an individual shelf. A shelf above a shelf of drawers to be installed so that when draws are pulled out from shelf, the back lip of the drawer catches on the upper shelf so as to create a drawer stop. Drawers may be punched with slots at front, back, and sides so as to accommodate font to back partitions or width dividers.

Dividers

Solid steel dividers to be stamped from minimum 24 gauge steel.

Bin Fronts

Minimum 18 gauge solid steel plates.

Bases

Minimum 18 gauge solid steel.

Finish/Color

All parts are electro statically painted with an industrial grade powder coat finish.

Standard System Adaptation Requirements

TECHNICAL SPECIFICATION STANDARD BULK RACK

Bulk storage units for hand load applications, with "V" shaped double flanged uprights. Units must have the flexibility of installation with all standard Standard solid and wire shelving unit components. Racks must be capable of side by side (common upright) installation within the storage system.

Steel Upright Posts

16 gauge cold rolled steel, rolled into a 1 5/8" wide, hollow "V” shape. Punched 1 1/2" on center along two of the three flanges for side by side assembly and maintaining a smooth outer appearance on the third, facing, side. Tapered slots in the uprights must accept shelf reinforcement clips, support beams for steel, wire grid and / or plywood shelving. Uprights are to be provided as a complete welded assembly.

Decking/Shelf Surfaces

a) Solid Steel Decking

22 gauge cold rolled and formed, 5/8" thick, corrugated steel sheets. Designed with one side ridged or ribbed for safety conscious, free and clear hand loading and reverse side flat channeled for flat surface loading. Decking sheets must overlap so as to create a secure and structurally strong shelf.

1. 15" deep decking in widths up to 8', maximum capacity of 4815 pounds.

2. 24" deep decking in widths up to 8'' maximum capacity of 3704 pounds,

3. 30" deep decking in widths up to 8', maximum capacity of 2870 pounds.

4. 36" deep decking in widths up to 8', maximum capacity of 2392 pounds.

5. 48" deep decking in widths up to 8' , maximum capacity of 2384 pounds.

b). "Drop in" Wire Grid Decking

Solid steel wire grid decking, .038” dia., designed to fit flush with top surface of formed beams. Decking grids set side by side within beam ledge so as to create a secure and structurally sound shelf structure; 24", 36" and 48" deep grid in widths up to 8', maximum capacity of 3000 pounds.

c). Super Duty Wire Shelves

Solid steel wire shelving and "V" shape wire truss. Truss to have lugs that secure into tapered upright notches for solid point load and upright to truss connection. Shelf maximum capacity of 1500 pounds each.

Miscellaneous Components

a) Back to Back Clamps used for additional structural integrity when placing units in rows back to back, minimum of two per pair of uprights.

b) Floor Anchors used to secure shelving uprights to floor to increase stability and to meet seismic standards.

c) Floor Plate used to protect linoleum or wood floors or to shim uneven floors.

d) Seismic Accessories - Brackets, braces, anchors, and clips used as specified in seismic applications.