16195 Final Electrical Identification with SCHEDULES.pdf

16195-1 (072125) 2009 by FEI

SECTION 16195

ELECTRICAL IDENTIFICATION

PART 1 - GENERAL

1.1 SUMMARY

A. Extent of electrical identification is indicated by drawings and schedules.

B. See ‘Electrical Equipment Identification Schedule’ on drawings for extent of equipment to be labeled and label verbiage.

C. Types of electrical identification specified in this section include the following:

1. Buried cable warnings.

2. Electrical power, control and communication conductors.

3. Operational instructions and warnings.

4. Danger signs.

5. Equipment/system identification signs.

D. Refer to Division 1 General Requirements Section, Identification Systems, for equipment and system nameplates and performance data; not work of this section.

PART 2 - PRODUCTS

2.1 ELECTRICAL IDENTIFICATION MATERIALS

A. General: Except as otherwise indicated, provide manufacturer's standard products of categories and types required for each application. Where more than one (1) single type is specified for an application, selection is Installer's option, but provide single selection for each application.

B. Plasticized Tags:

1. General: Manufacturer's standard pre-printed or partially pre- printed accident-prevention and operational tags, of plasticized card stock with matte finish suitable for writing, approximately 3-1/4-inch x 5-5/8-inch, with brass grommets and wire fasteners, and with appropriate pre-printed wording including large-size primary working, e.g., DANGER, CAUTION, DO NOT OPERATE.

C. Self-Adhesive Plastic Signs:

1. General: Provide manufacturer's standard, self-adhesive or pressure-sensitive, pre-printed, flexible vinyl signs for operational instructions or warnings; of sizes suitable for application areas and adequate for visibility, with proper wording for each application, e.g., 208V, EXHAUST FAN, RECTIFIER.

a. Colors: Unless otherwise indicated or required by governing regulations, provide orange signs with black lettering.

16195-2

D. Baked Enamel Danger Signs:

1. General: Provide manufacturer's standard "DANGER" signs of baked enamel finish on 20-gage steel; of standard red, black and white graphics; 14-inch x 10-inch size except where 10-inches x 7-inches is the largest size which can be applied where needed, and except where larger size is needed for adequate vision; with recognized standard explanation wording, e.g., HIGH VOLTAGE, KEEP AWAY, BURIED CABLE, DO NOT

TOUCH SWITCH.

E. Engraved Plastic-Laminate Signs:

1. General: Provide engraving stock melamine plastic laminate, complying with FS L-P-387, in sizes and thicknesses indicated, engraved with engraver's standard letter style of sizes and wording indicated, black face and white core (letter color) except as otherwise indicated, punched for mechanical fastening except where adhesive mounting is necessary because of substrate.

a. Thickness: 1/16-inch, for units up to 20 sq. in. or 8-inch length; 1/8-inch for larger units.

b. Fasteners: Double sided tape, except contact-type permanent adhesive where tape will not adhere to surface.

c. Label size at ‘Load’ to be 2 1/2” x 4” label size at breaker to be 1” x 2 1/2”.

F. Color-Coded Conduit Markers:

1. General: Provide manufacturer's standard pre-printed, flexible or semi-rigid, permanent, plastic-sheet conduit markers, extending 360º degrees around conduits; designed for attachment to conduit by adhesive, adhesive lap joint of marker or matching adhesive plastic tape at each end of marker, or pretensioned snap-on. Except as otherwise indicated, provide lettering which indicates voltage of conductor(s) in conduit. Provide 8-inch minimum length for 2-inch and smaller conduit, 12-inch length for larger conduit.

a. Colors: Unless otherwise indicated or required by governing regulations, provide orange markers with black letters.

2.2 LETTERING AND GRAPHICS

A. General: Coordinate names, abbreviations and other designations used in electrical identification work, with corresponding designations shown, specified or scheduled. Provide numbers, lettering and wording as indicated or, if not otherwise indicated, as recommended by manufacturers or as required for proper identification and operation/maintenance of electrical systems and equipment. Comply with ANSI A13.1 pertaining to minimum sizes for letters and numbers.

PART 3 - EXECUTION

3.1 APPLICATION AND INSTALLATION

A. General Installation Requirements:

1. Install electrical identification products as indicated, in accordance with manufacturer's written instructions and requirements of NEC.

16195-3

2. Coordination: Where identification is to be applied to surfaces, which require finish, install identification after completion of painting.

3. Regulations: Comply with governing regulations and requests of governing authorities for identification of electrical work.

B. Operational Identification and Warnings:

1. General: Wherever reasonably required to ensure safe and efficient operation and maintenance of electrical systems, and electrically connected mechanical systems and general systems and equipment, including prevention of misuse of electrical facilities by unauthorized personnel, install self-adhesive plastic signs or similar equivalent identification, instruction or warnings on switches, outlets and other controls, devices and covers of electrical enclosures. Where detailed instructions or explanations are needed, provide plasticized tags with clearly written messages adequate for intended purposes.

C. Danger Signs:

1. General: In addition to installation of danger signs required by Governing regulations and authorities, install appropriate danger signs at locations indicated and at locations subsequently identified by Installer of electrical work as constituting similar dangers for persons in or about Project.

a. High Voltage: Install danger signs wherever it is possible, under any circumstances, for persons to come into contact with electrical power of voltages higher than 250-volts.

b. Critical Switches/Controls: Install danger signs on switches and similar controls, regardless of whether concealed or locked up, where untimely or inadvertent operation (by anyone) could result in significant danger to persons, or damage to or loss of property where instructed by Architect.

D. Equipment/System Identification:

1. General: Install engraved plastic-laminate sign on each major unit of electrical equipment in building; including central or master unit of each electrical system including communication/control/signal systems, unless unit is specified with its own self-explanatory identification or signal system. Signs for disconnect switches, motor starters, contactors and similar equipment shall indicate the load served. Except as otherwise indicated, provide single line of text, 1/2-inch high lettering on 1-1/2-inch high sign (2-inch high where two (2) lines are required), white lettering in black field. Lettering for emergency power system components shall be white lettering in red field. Provide text matching terminology and numbering of the Contract Documents and shop drawings. Provide signs for each unit of the following categories of electrical work.

a. Panelboards, electrical cabinets and enclosures.

b. Access panel/doors to electrical facilities.

c. Major electrical switchgear.

d. Disconnect switches.

e. Motor control centers.

f. Motor starters.

g. Contactors.

16195-4

h. Power transfer equipment.

i. Transformers.

2. Install signs at locations indicated or, where not otherwise indicated, at location for best convenience of viewing without interference with operation and maintenance of equipment. Secure to substrate with fasteners, except use adhesive where fasteners should not or cannot penetrate substrate.

E. Cable/Conductor Identification:

1. General: Apply cable/conductor identification in each box/enclosure/cabinet, except where another form of identification (such as color-coded conductors) is provided. Match identification with marking system used in distribution switchboards, shop drawings, contract documents, and similar previously established identification for project electrical work.

END OF SECTION

16195-5 (072125) 0108 P1

BJ/1J Electrical Equipment Label Schedule

LABEL

INSTALLED

BY

LOCATION

LABEL AT LOAD

LABEL AT BREAKER

CKT

NO.

Contractor Sub BJ

15 kV SW Switch BJ

Fed from SAC 4B

Contractor Transformer Sub BJ

1000 KVA

Contractor Distribution Swbd. BJ

Distr. Switchboard BJ Fed from Sub BJ

Main Fed from Sub BJ

MBJ

Tie Fed from Panel 1J

BJ/1J

Contractor

MCC BJ

Fed from Dist. Swbd. BJ

MCC BJ

Room BJ15

BJ1

Contractor BJ UPS Input

Fed from Dist. Swbd. BJ BJ UPS Input Room BJ17

BJ2

Contractor Panel UDP1

Fed from Dist. Swbd. BJ Panel UDP1 Room BJ17

BJ4

Contractor UPS BJ/1J Bypass Swbd.

Fed from Dist. Swbd. BJ UPS BJ/1J bypass

Distr. Swbd.

BJ5

Contractor Transformer TMDP

Fed from Dist. Swbd. BJ Transformer MDP

Room BJ19

BJ3

Contractor Spare BJ6

Govt. Panel MDP Panel MDP

Fed from Dist. Swbd. BJ Transformer TMDP

Govt. Panel MDP-A Panel MDP-A

Fed from BJ Panel MDP

Govt. Panel PB2 Panel PB2

Govt. Panel PB1 Panel PB1

Govt. Panel LB3 Panel LB3

Govt. Panel LB2 Panel LB2

Govt. Panel BBP Panel BBP

Govt. Panel LB1 Panel LB1

Govt.

Panel EM1

Fed from MCC BJ Panel EM1 BJ Corridor

Transformer

TEM1

Transformer TEM1 Fed from MCC

BJ Feeds Panel EM1

16195-6 (072125) 0108 P1 2009 by FEI

BJ/1J Electrical Equipment Label Schedule

INSTALLED

BY

LOCATION

LABEL AT LOAD

LABEL AT BREAKER

CKT

NO.

Contractor Sub 1J

15 kV SW Switch 1J

Fed from SAC 4A

Sub 1J

Swbd. 1J

Dist. Switchboard 1J Fed From Sub 1J

Fed from Sub 1J

M1J

Fed from Panel BJ

1J/BJ

MCC 1J

Room 1J11

1J1

Contractor

1J UPS

Fed from Dist. Swbd 1J Input 1J UPS Input Room BJ17

1J2

Spare 1J3

Contractor MCC 1J

MCC 1J

Fed from Dist. Swbd. 1J

Panel 1LA

Fed from MCC 1J Panel 1LA Room 1J8

Panel 1LB

Fed from MCC 1J Panel 1LB Room 1J8

Contractor Panel 1LB1 Panel 1LB1

Fed from 1J Panel 1LB

T1LA

Transformer T1LA Fed from MCC1J Feeds Panel 1LA

T1LB

Transformer T1LB Fed from MCC1J Feeds Panel 1LB

BJ/1J UPS

Bypass Dist.

Swbd.

(future connection) Maintenance Bypass Panel 1JA

(future connection)

Maintenance Bypass Panel BJA

UPS 1J Rm 1J12 Bypass

UPS BJ Bypass Rm BJ17

16195-7

2J/3J ELEC. EQUIPMENT IDENTIFICATION SCHEDULE

INSTALLED

BY

LOCATION LABEL AT LOAD LABEL AT

BREAKER CKT. NO

Contractor Sub 2J

15 kV SW Switch 2J

Fed from SAC 4B

Sub 2J

Swbd 2J

Distr. Switchboard 2J Fed from Sub 2J

M2J

Fed from Sub 3J

2J/3J

Contractor

MCC 2J

Fed from Dist. Swbd 2J

MCC 2J

Room 2J11 2J2

Contractor 2J UPS Input

Fed from Dist. Swbd 2J 2J UPS Input 2J5

Contractor Panel MS1

Fed From Dist. Swbd 2J Panel MS1 2J3

Spare 2J6

Contractor CAC16 CAC16 Rm. 2J15 Fed from Sub 2J

2J1

Contractor TUP1 TUP1 Rm. 3J2 2J4

Contractor Sub 3J

15 kV SW Switch 3J

Fed from SAC 4A

Sub 3J

Swbd 3J

Distribution Swbd 3J

M3J

3J/2J

Contractor

MCC 3J

Fed from Sub 3J

MCC 3J

Room 3J11 3J1

Contractor 3J UPS Input

Fed from Dist.

Swbd 3J

3J UPS Input Room 3J15

3J5

Contractor UPS 2J/3J Bypass Swbd

Fed from Dist.

Swbd. 3J

UPS 2J/3J Bypass Swbd. Rm. 2J12

3J4

Contractor

XFMR HA/Pnl 2HA/Pnl

3HA

Fed from Dist. Swbd.

Panel 3J

Panels 2HA/3HA Rooms 2J4/3J4

3J3

16195-8

2J/3J ELEC. EQUIPMENT IDENTIFICATION SCHEDULE

INSTALLED

BY

LOCATION LABEL AT LOAD LABEL AT

BREAKER CKT. NO

Spare 3J2

Govt.

Transformer

T2LA

Transformer T2LA Fed from Panel 2HA Feeds

Panel 2LA

Govt. Panel 2LA Panel 2LA

Fed from 3J Panel 2HA

UPS 2J/3J

Bypass Dist. Swbd.

Space Future

UPS 2J Bypass

UPS 3J Bypass

UPS 2JA

Maint. Bypass

UPS 3JA

Maint. Bypass