CASS_Attachment_4_Touch_Screens_Hardware.pdf

Touch Screen:

Exter T70 & T150

Hardware

Table of Contents

1. Exter Installation Manual pg 3- 16

EXTER

TM

T70 Optimal viewing: 640 x 480 pixels, high-resolution 6.5" TFT-display

EXTER

TM

T100 Optimal viewing: 800 x 600 pixels, high-resolution 10.4" TFT-display

EXTER

TM

T150 Optimal viewing: 1024 x 768 pixels, high-resolution 15.1" TFT-display

Installation manual

Table of Contents

1. Safety Precautions 3

1.1 UL Installation 3

1.2 General 3

1.3 During Use 3

1.4 Service and Maintenance 4

1.5 Dismantling and Scrapping 4

2. Installation 5

2.1 Space Requirements 5

2.2 Installation Process 6

2.2.1 Mode Switches 7

2.2.2 Connections to the Controller 7

2.2.3 Other Connections and Peripherals 7

3. Technical Data 8

4. Chemical Resistance 9

4.1 Metal Casing 9

4.2 Keyboard and Display 9

4.2.1 Autotex F250 9-10

4.2.2 Touch Screen Surface 10

5. Operator Terminal Drawings 11

5.1 Communication Ports 11

5.2 EXTER Outline

5.2.1 EXTER

TM

T70 Outline 12

5.2.2 EXTER

TM

T100 Outline 13

5.2.3 EXTER

TM

T150 Outline 14

1. Safety Precautions

The installer and the owner and/or operator of the operator terminal must read and understand this installation manual.

1.1. UL Installation

Power, input and output (I/O) wiring must be in accordance with Class 1, Division 2 wiring methods

(Article 501-4 (b) of the National Electric Code, NFPA 70) and in accordance with the authority having jurisdiction.

1.2. General

• Only qualified personnel may install or operate the operator terminal.

• The operator terminal must be installed according to the installation instructions.

• The operator terminal is designed for stationary installation on a plane surface, where the following conditions are fulfilled:

o no high explosive risks o no strong magnetic fields o no direct sunlight o no large, sudden temperature changes

• Never allow fluids, metal filings or wiring debris to enter any openings in the operator terminal. This may cause fire or electrical shock

• The operator terminal fulfills the requirements of article 4 of EMC directive 89/336/EEC

• Storing the operator terminal where the temperature is lower/higher than recommended in this manual can cause the LCD display liquid to congeal/become isotopic

• The LCD display liquid contains a powerful irritant. In case of skin contact, wash immediately with plenty of water. In case of eye contact, hold the eye open, flush with plenty of water and get medical attention

• The supplier is not responsible for modified, altered or reconstructed equipment

• Use only parts and accessories manufactured according to specifications of the supplier

• Peripheral equipment must be appropriate for the application and location

• The figures in this manual serve an illustrative purpose. Because of the many variables associated with any particular installation, the supplier cannot assume responsibility for actual use based on the figures

• The supplier neither guarantees that the operator terminal is suitable for your particular application, nor assumes responsibility for your product design, installation or operation

1.3. During Use

• Keep the operator terminal clean.

• Emergency stop and other safety functions may not be controlled from the operator terminal

• Do not use too much force or sharp objects when touching the keys, display etc.

1.4. Service and Maintenance

• Only qualified personnel should carry out repairs

• The agreed warranty applies

• Before carrying out any cleaning or maintenance operations, disconnect the equipment from the electrical supply

• Clean the display and surrounding front cover with a soft cloth and mild detergent

• Replacing the battery incorrectly may result in explosion. Only use batteries recommended by the supplier.

1.5. Dismantling and Scrapping

• The operator terminal or parts thereof shall be recycled according to local regulations

• The following components contain substances that might be hazardous to health and the environment: lithium battery, electrolytic capacitor and display

2. Installation

2.1. Space Requirements

• Installation plate thickness: 1.5 - 9.0 mm (0.06 - 0.35 inch)

• Space requirements when installing the operator terminal:

EXTER

TM

T70

EXTER

TM

T100

EXTER

TM

T150 Caution The openings on the enclosure are for air convection. Do not cover these openings.

2.2. Installation Process

1. Unpack and check the delivery. If damage is found, notify the supplier.

Note: Place the operator terminal on a stable surface during installation. Dropping it or letting it fall may cause damage.

2. Place the panel cut out where the operator terminal is to be situated, draw along the outer sides of the holes and cut according to the markings.

3. Secure the operator terminal in position, using all the fastening holes and the provided brackets and screws:

4. Connect the cables in the specified order

Caution-Ensure that the operator terminal and the controller system have the same electrical grounding

(reference voltage level), otherwise errors in communication may occur.

Caution-Use a M5 screw and a grounding conductor (as short as possible) with a cross-section of minimum 2.5 mm

Caution-Use only shielded communication cables.

-Separate high voltage cables from signal and supply cables.

Caution-The operator terminal must be brought to ambient temperature before it is started up. If condensation forms, ensure that the operator terminal is dry before connecting it to the power outlet.

- Ensure that the voltage and polarity of the power source is correct.

5. Carefully remove the laminated film over the operator terminal display, to avoid static electricity that could damage the terminal.

2.2.1. Mode Switches

All mode switches must be in OFF position during operator terminal use. The mode switches should not be touched unless by qualified personnel.

2.2.2. Connections to the Controller

For information about the cables to be used when connecting the operator terminal to the controller, please refer to the help file for the driver in question.

2.2.3. Other Connections and Peripherals

Cables, peripheral equipment and accessories must be suitable for the application and its environment. For further details or recommendations, please refer to the supplier.

Caution When using a compact flash card, do not remove the card when the busy indicator is illuminated.

3. Technical Data

Parameters

EXTERTM T70

Front panel, W x H x D 219 x 154 x 6 mm Active area of display, W x H 131.5 x 98.6 mm

Display TFT-LCD. 640 x 480 pixels, 64K color.

CCFL backlight lifetime at the ambient temperature of +25 °C: 50,000 h.

Power consumption at rated voltage Normal: 0.4 A Maximum: 0.9 A

EXTERTM T100

Front panel, W x H x D 302 x 228 x 6 mm Active area of display, W x H 211.2 x 158.4 mm

Display TFT-LCD. 800 x 600 pixels, 64K color.

CCFL backlight lifetime at the ambient temperature of +25 °C: 50,000 h.

Power consumption at rated voltage Normal: 0.5 A Maximum: 1.0 A

EXTERTM T150

Front panel, W x H x D 398 x 304 x 6 mm Active area of display, W x H 304.1 x 228.1 mm

Display TFT-LCD. 800 x 600 pixels, 64K color.

CCFL backlight lifetime at the ambient temperature of +25 °C: 50,000 h.

Power consumption at rated voltage Normal: 1.2 A Maximum: 1.7 A

Common Mounting depth 55 mm (155 mm including clearance) Front panel seal IP 66 Rear panel seal IP 20 Keyboard material/ Front panel Touch screen: Polyester on glass *, 1 million finger touch operations.

Overlay: Autotex F250 *.

Reverse side material Powder-coated aluminum Weight 1.1 kg Serial port RS422/RS485 25-pin D-sub contact, chassis-mounted female with standard locking screws 4-40 UNC.

Serial port RS232C 9-pin D-sub contact, male with standard locking screws 4-40 UNC.

Ethernet Shielded RJ 45 USB Host type A, power consumption max. 500mA Device type B CF-slot Compact flash, type I and II Flash memory for application 4 MB Real time clock ±20 PPM + error because of ambient temperature and supply voltage.

Total max error: 1 min/month at 25 °C

Minimum life of the real time clock battery: 3 years Temperature coefficient: 0.004 ppm/°C2

Fuse Internal DC fuse, 3.15 AT, 5 x 20 mm

Power supply

+24V DC (20 - 30V DC). 3-pin jack connection block.

CE: The power supply must conform to the requirements for SELV or PELV according to IEC 950 or IEC 742.

UL: The power supply must conform with the requirements for class II power supplies

Ambient temperature Vertical installation: 0 ° to +50 °C Horizontal installation: 0 ° to +40 °C Storage temperature -20 ° to +70 °C Relative humidity 5 - 85 % non-condensed

EMC tests on the The operator terminal conforms to the essential protection requirements in article 4 of the directive 89/336/EEC.

operator terminal Noise tested according to EN6100-6-4 emission and EN61000-6-2 immunity.

UL, cUL approvals Certification in progress

* See section Chemical Resistance for keyboard and display

4. Chemical Resistance

4.1. Metal Casing

The frame and casing material is powder-coated aluminum. This powder paint withstands exposure of up to 24 hours duration to the following chemicals without visible change:

Ammonia 25% Isopropyl alcohol Nitric acid 3% De-ionized water Tap water Chlorhydric acid 10% Butanol Cooling liquid 50% Washer fluid 33% Citric acid 10% Ligroin Sulphuric acid 20% Diesel Cooking oil Turpentine Ethanol 99.5% denaturated Lactic acid 10% Urea saturated FAM-Normal petrol Sodium di-chromate saturated Hydroperoxide 3% Alcohol 95% Caustic soda 5% Acetic acid 10% Phosphoric acid 43% Sodium hypochlorite solution Alu-cleaner Glycol Sodium carbonate 10% - Industrial petrol Sodium chloride 20% -

4.2. Keyboard and Display

4.2.1. Autotex F250

Autotex F250 covers the overlay surrounding the touch screen

Solvent Resistance Autotex F250 withstands exposure of more than 24 hours duration under DIN 42 115 Part 2 to the following chemicals without visible change:

Potassium ferrocyanide/ ferricyanide Sodium hypchlorite <20% (bleach) 1.1.1. Trichloroethane (Genklene) Cyclohexanol Acetaldehyde Ethylacetate Diacetone alcohol Aliphatic hydrocarbons Diethyl ether Glycol Toluene N-Butyl acetate Isopropanol Xylene Amylacetate Glycerine White spirit Butycellosolve Methanol Fromic acid <50% Ether Triacetin Acetic acid <50% MIBK Dowanol DRM/PM Phosphoric acid <30% Cutting oil Acetone Hydrochloric acid <36% Potassium carbonate Metyl ethyl ketone Nitric acid <10% Washing powders Dioxan Trichloracetic acid <50% Fabric conditioner Cyclohexanone Sulphuric acid <10% Ferric chloride Ethanol Formaldehyde 37% - 42% Ferrous chlorid Isophorone Potassium hydroxide <30% Dibutyl Phthalate Ammonia <40% Linseed oil Dioctyl Phthalate Caustic soda <40% Paraffin oil Sodium carbonate Hydrogen peroxide <25% Blown castor oil Petrol Alkalicarbonate Silicone oil Teepol Bichromate Turpentine substitute Water Diesel oil Univeral brake fluid Sea water Acetonitrile Decon - Sodium bisulphate Aviation fuel -

Autotex withstands DIN 42 115 Part 2 exposure of up to 1 hour duration to glacial acetic acid without visible change.

Autotex is not resistant to high pressure steam at over 100 °C or the following chemicals:

Concentrated mineral acids Benzyl alcohol Concentrated caustic solution Mehylene chloride

Autotex withstands 24 hours exposure to the following reagents at 50 °C without visible staining:

Top Job Grape Juice Ariel Ajax Jet Dry Milk Persil Vim Gumption Coffee Wisk Domestos Fantastic - Lenor Vortex Formula 409 - Downey Windex

Very slight discoloration was noted under critical viewing conditions with the following materials:

Tomato juice Tomato ketchup Lemon juice Mustard

Outdoor Use: In common with all polyester based films Autotex F250 is not suitable for use in conditions of long term exposure to direct sunlight.

4.2.2. Touch Screen Surface

The touch screen surface on the operator terminal withstands exposure to the following solvents without visible change:

Solvents Time Acetone 10 minutes Isopropanol 10 minutes Toulene 5 hours

Protection Film It is recommended to use the Autoflex EB touch display protection film, supplied by Beijer Electronics AB.

5. Operator Terminal Drawings

5.1. Communications Ports

5.2. Terminal Outline

5.2.1.

5.2.2.

5.2.3.