EXHIBIT C(1) - Prisoner Transport Module Reqs.docx

EXHIBIT C(1)

Requirements for the Two 30-34-Passenger Prisoner Transport Modules

Due to the technical nature of this project, Bidders are required to provide detailed drawings and detailed specifications of exactly what they are proposing. Bids not providing these required support documents shall be deemed non-responsive and rejected.

Drawings shall include four (4) exterior views showing lights, equipment, stripes, lettering, etc. and four (4) interior drawings showing cabinets, benches, equipment placement, etc.

The use of standard drawings and standard specifications or copies of bid drawings does not constitute detailed drawings and detailed specifications and shall not be considered. In order to make evaluations of proposals, manufacturers detailed specifications shall be in the same order as the bid document. Minor details of construction and materials, where not otherwise specified, are left to the discretion of the contractor, who shall be solely responsible for the design and construction of all features.

1.2

NEW MATERIAL

All equipment furnished shall be guaranteed to be new and of current manufacture and to meet all requirements of these specifications. Workmanship shall be of high quality and accomplished in a professional manner so as to ensure a safe and functional Module.

1.3.01 Warranty Period.

Bidder shall provide a lifetime warranty against defective workmanship and materials, and a 5-year limited warranty for parts. Under this warranty, Bidder’s liability is limited to furnishing DOC, without cost to DOC, parts, and labor required to replace parts or defective material and workmanship when there is no indication of misuse, neglect, improper maintenance, accident, or overloading of the Module. Parts and labor will be supplied after inspection by an authorized agent of the manufacturer. Defective parts shall be returned prepaid by Bidder. All third-party warranties shall pass to DOC.

1.3.02 Remount.

DOC expects to remount this module at a future date, so Bidder shall supply a copy of the current remount warranty with the bid. If the manufacturer does not provide remount services Bidders shall provide the name, address, phone, and history of the company who does provide the remount services, a current copy of their remount warranty, and the company is required to meet the same insurance requirements as a Bidder under this RFQQ.

1.3.03 Repair.

The bidder must perform Module repairs in Washington State. After notification is provided for a repair need, the Bidder must start repair work within 72 hours. The vehicle can be out of commission for a maximum of seven days starting from the repair call notification.

Bidder shall provide a pre-build meeting and a final inspection meeting at the manufacturing facility. Notice of the meeting and duration of the meeting shall be reasonable and set by Bidder. The Pre-build Final Inspection meeting shall be for several DOC personnel.

The following modifications will be made to the chassis by Bidder:

1. Install Rubber Mud Flaps behind rear wheels

2. Install a U-bolt driveline guard.

3. Remove rear bench seat and replace with one OEM fixed bucket seats on passenger side.

4. Install a new locking fuel cap on chassis fuel tank.

5. On-Spot brand automatic chains shall be installed on the rear axle of Chassis.

6. Spray the chassis underbody with undercoating for reduced corrosion and added sound deadening (excluding the area above the fuel tank, driveline, and exhaust lines, per manufacturer's specifications).

7. A Custom front console made of black-powered-coated formed aluminum to be installed to accommodate cup holders, locking storage compartment and Motorola Radio equipment, security monitor, and various rocker type switches and warning lights. Exact layout and design to be determined by DOC prior to build.

8. Install (2) Santa Cruz Gunlocks. This should be a vertical floor mounted system in the driver side rear compartment of the cab. Must be able to hold (2) AR15s (1) 12 gauge shotgun and (1) 40mm Launcher. Racks shall be installed on a custom painted aluminum bracket in the cab.

9. A custom guarded push button switch shall be installed on the front driver’s console for the gun storage lock.

10. A custom designed rear console work area made of black-powder-coated formed aluminum shall be installed between the rear seats. This area is for mounting video monitor(s), and a locking center console designed for weapons storage and equipment. Exact layout and design dependent on Freightliner M2-106 Crew Cab chassis dimensions, and as discussed by DOC prior to build.

11. A 9” frame extension shall be welded to each OEM frame rail to provide rear lateral and bumper support and to provide a step height of 12.5” from the bumper to the module floor.

12. OEM exhaust shall be routed from right rail location to left side, exiting just forward of the rear wheels.

13. Two TM-21 auxiliary engine mounted compressors with brackets (or approved equivalent) shall be added to the OEM engine.

14. A basket-style spare tire carrier shall be installed under the chassis aft of the rear axle. The OEM spare tire and wheel shall be secured o the carrier assembly with a chain and lock.

15. Install two Whelen #WIONSMCK Clear Lens Red/Amber Split LED flashers with chrome housings on chassis grille. Lights shall be controlled by “Flasher” switch on the driver’s console.

Overall Vehicle including Exterior Module Dimensions: (Specifications are listed as minimums.)

There shall be 12" drop skirting from the front of the module to the wheel wells. No drop skirting shall be provided aft of the rear wheel wells to accommodate departure angles. Size of drop skirting may be adjusted to ensure specified sizing of compartments No. 5 & 6.

All body and compartment seams at or below floor level shall be full seam welded. The entire perimeter of the subfloor shall be completely sealed with a caulking material, creating a watertight, dust-free module environment.

The compartments are streetside and curbside and dimensions to be agreed upon by DOC and the approved Bidder. All compartments shall be securely welded to the subfloor and structural framing. A baffled drain hole shall be provided in all exterior compartment bottoms that extend below the floor line. All exterior adjustable shelves shall be mounted on heavy-duty aluminum track, which is securely welded to compartment interior. Each shelf shall support at least 300 lbs. of equipment.

Dimensions: 60.25” W x 16.75” H x 17.5” D Shelves - None Door(s) - 2" pan Aluminum, hinged door with two t-style keeper latches.

Light(s) – One Led strip light Additional instruction –

1. Compartment shall be accessible from exterior only.

2. 2. Electrical component panel shall be installed on the back wall.

3. 3. A Samlex PST Series 600-watt inverter shall be installed in this compartment.

4. 4. A BNW supplied two-channel amplifier shall be installed in this compartment.

5. 5. A 45-amp minimum battery charger/conditioner shall be installed in this compartment.

Dimensions: 51” W x 21.625” H x 23” D Shelves - None Door(s) - 2" pan Aluminum, bottom hinged door with deadbolt.

Light(s) – One Led strip light Additional instruction –

1. A vent with MERV 8 polyester filter media shall be installed on the forward wall of No 2 and the aft wall on No 4.

Dimensions: 51” W x 21.625” H x 23” D Shelves - None Door(s) - 2" pan Aluminum, bottom hinged door with deadbolt.

Light(s) – One Led strip light Additional instruction – None

Dimensions: 71” W x 21.625” H x 23” D Shelves - None Door(s) - 2" pan Aluminum, bottom hinged door with deadbolt.

Light(s) – One Led strip light

1. A vent with MERV 8 polyester filter media shall be installed on the aft wall.

Dimensions: 32” W x 21.625” H x 23” D Shelves - None Door(s) - 2" pan Aluminum, bottom hinged door with deadbolt.

Light(s) – One Led strip light

1. A vent with MERV 8 polyester filter media shall be installed on the aft wall.

Dimensions: 45” W x 21.625” H x 23” D Shelves - None Door(s) - 2" pan Aluminum, bottom hinged door with deadbolt.

Light(s) – One Led strip light

1. A 25-gallon black water holding tank shall be install in this compartment.

Dimensions: 27” W x 53” H x 10” D Shelves - None Door(s) - 2" pan Aluminum, bottom hinged door with deadbolt.

Light(s) – One Led strip light

1. Two vertical strips of heavy-duty aluminum track shall be installed on the back wall with two mill-finish aluminum plates – each with two “J” hooks – mounted on the track for storing customer-supplied restraints.

1. Shall be semi-flush mounted, chrome plated Eberhard Grabber # 21100. All exterior doors shall have rotary latch striker posts, which meet FMVSS 206 requirements. Striker shall be adjustable and shall be secured with a nut from behind door frame. The striker washer will not be removed. Guards shall be added to the top of the striker posts at the bottom of rear and curbside passage door openings to reduce the risk of snagging clothing or leg chains when exiting. Doors greater than 45” tall shall have double rotary latches active by stainless steel rods. Once final adjustments have been made, thread shall have Loctite or equivalent applied. Doors will latch to doorframe mounted striker posts only and not to one another. All latches will have a non-slip surface on the underside of the latch. All entrance doors shall have exterior handles only, with dual point, rod actuated, rotary latch systems which are lockable inside and out. All compartment and module access doors shall be keyed for J236 "double edged" keys.

2. All exterior doors, excluding Compartment No. 1 and 9, shall have a dead bolt lock added adjacent to the paddle latch location of the door. Deadbolt lock shall be single sided.

3. Security Cells interior aisle doors shall have deadbolts. Locks striker recess shall be a minimum of 1" deep.

4. All Schlage deadbolt locks shall be cam over spring actuated type and keyed to DOC specifications. Any exposed screws shall be sealed to prevent vandalism.

One (1) curbside forward, main entry door shall be 31"W x 81.75"H. An interior security door shall be installed at the curbside passage door. One (1) Rear module door shall be 31"W x 73.75"H. An interior security door shall be installed shall be installed on the Rear door.

No interior cabinets inside the module.

Dimensions- 22"W x 78"H x 34"D Location – Cells 1, 2, 3 streetside, aisle facing. Cell 9 curbside, aisle facing.

Interior Door – 20” W x 76”H Cell Door(s) – Doors shall be made of 0.123” hex punched aluminum. The inside of the punched portion of the door – expect for 10” kept open at the bottom for ventilation – shall be covered with 0.1875” polycarbonate. Door shall have a deadbolt-locked handcuff door made of punched aluminum with 0.1875: polycarbonate covering the inside of the punched portion with a single-sided Schlage deadbolt lock. Door shall have a stainless-steel piano hinge with thread locking product applied to the hinge screws; shall have the hinge on the aft side of the door.

Seating - one (1) Bench seat, facing aisle Additional Instructions –

1. A camera in a recessed pocket, shall be installed in these cells. Four (4) cameras total specifically for the isolation cells with one (1) camera in each cell.

Aisle Doors(s) - Four.

3.16

COMPARTMENT No. 4 & 8 (Isolation Cells) Dimensions- 31.75"W x 78"H x 34"D Location – Cells 4 streetside, forward. Cell 8 curbside, forward.

Interior Door – 20” W x 76”H Cell Door(s) – Doors shall be made of 0.123” hex punched aluminum. The inside of the punched portion of the door – expect for 10” kept open at the bottom for ventilation – shall be covered with 0.1875” polycarbonate. Door shall have a deadbolt-locked handcuff door made of punched aluminum with 0.1875: polycarbonate covering the inside of the punched portion with a single-sided Schlage deadbolt lock. Door shall have a stainless-steel piano hinge with thread locking product applied to the hinge screws; shall have the hinge on the aft side of the door.

Seating - one (1) Bench seat, facing forward Additional Instructions –

1. A camera in a recessed pocket, shall be installed in these cells.

2. An 18.75” x 11.25” horizontal window with fixed glass shall be installed on the module wall. Window shall have 14 ga. Hex-punched stainless-steel cover riveted in place over the inside surface.

Aisle Doors(s) - Two.

Dimensions – 178.5” W x 78”H x 100” D Location – Streetside and curbside, center Seating – Twelve (12) Freedman bench seats, facing forward Additional Instructions –

1. Eleven (11) Freedman Seating #CITI-36223-2PRIG gray 36” W two-person prison bench seats with mounting hardware shall be installed in this cell, six streetside and five curbside.

2. Nine (9) 18.75” x 11.25” windows with fixed glass shall be installed, five streetside and four curbside. Windows shall have 14 ga. Hex-punched stainless-teel covers riveted in place over the inside surface.

3. A 25.125” W locking door made of 0.125” hex punched aluminum shall be installed between this cell and Cell #6; door shall have double-sided Schlage deadbolt lock.

4. HVAC units shall be in an upper closeout, ceiling level; one streetside and one curbside. UV-C filtering is desired.

5. Two (2) cameras, each in a recessed pocket, shall be installed in the ceiling of this cell; one forward facing and one aft facing.

Dimensions – 97” W x 78”H x 28.875” D Location – Rear Seating – Two (2) 34”L x 10” D padded flip-up benches, each with spring-loaded seat irons to keep the bench in the upright position except during use. Non-padded aluminum benches are acceptable.

Additional Instructions –

1. Benches shall be full depth with seating for two persons each.

2. A 25.125” W locking door made of 0.125” hex punched aluminum shall be installed between this cell and Cell #6; door shall have double-sided Schlage deadbolt lock.

3. One (1) camera in a recessed pocket, shall be installed in the ceiling of this cell; upper streetside forward corner.

Dimensions – 34” W x 78”H x 34” D Location – Curbside Additional Instructions –

1. A Microphor #LF-3230 12 VDC stainless steel toilet with push button flush shall be installed in this area.

2. An access panel shall be located on the forward wall from the freshwater tank installed under bench in Cell # 8.

3. The floor of the lavatory shall be stainless steel and extend up the wall 36-inches. A drain shall be installed in the floor, with a duckbill valve.

4. A Kingsway Group #KG23 ligature-resistant two roll surface mounted toilet paper dispenser shall be installed in the lavatory; exact location to be determined.

5. A painted aluminum half-wall door with locking paddle latch shall be installed for privacy and security.

6. An 18/75: x 11/25: horizontal window with fixed glass shall be installed on the module wall. Window shall have 14 ga hex-punched stainless-steel cover riveted in place over the inside surface.

7. A footwell incursion (for the forward curbside bench seat in Cell #5) shall be located on the aft wall.

1. A recessed double step doorstep shall be provided which is 19" deep x 31" wide at-the curbside passage door.

2. There shall be a drain hole and an open grate step plate screwed in place with security screws, which is removable for cleaning purposes.

3. Polished aluminum diamond plate kick panel will be installed on the sides and face of doorstep

1. Shall be a welded construction of 3" x 3" x 0.375" aluminum angle and 2" x 0.250" plate and shall be covered by 0.125" bright aluminum diamond plate.

2. The center section will provide a 12" step with a raised step in the center position.

3. The outermost 12" of each end shall be angled to prevent dragging of comers in high angle of approach/departure areas.

4. Diamond plate shall be formed on front and rear edges for channel type strength and formed 0.090" aluminum close out shall be welded to the underside of the step/bumper.

5. The bumper shall be bolted directly to the chassis frame using high strength Grade 5 bolts.

6. Bumper shall be easily removable and replaceable in case of damage.

7. A Kwikee triple electric step shall be mounted under the bumper, centered below the rear passenger door.

1. Shall be bright finished extruded aluminum of a double channel design and 0.125" wall thickness for maximum strength.

2. Rub rails shall be 2.5" high x 0.75" wide and run along the lower edge of body, interrupted only by wheel well opening.

3. A black Scotchlite stripe shall be installed in the rub rails.

1. Shall be installed on the module.

2. They shall be high grade weather-resistant industrial rubber with a rounded outer edge following the full contour of the wheel well opening and protrude 2.5” from the module body.

1. Shall be extruded, anodized aluminum running full length of module at the top of sides, front, rear, and over each exterior compartment.

2. Drip rails shall be installed with stainless steel screws and be detachable for easy replacement.

3. All drip rails shall be finished with 45 degree angled ends to avoid hooking materials which brush against the vehicle causing damage.

Made of bright aluminum diamond plate shall cover front module comers 24" up from bottom of the body, 2.5" down the side of body, and meet the cab at the front of body.

Made of bright aluminum diamond plate shall extend from the top of the rear step to the bottom of the rear doors, full width formed around comers, and 2.5" forward on each side

1. Shall have black anodized aluminum frames, rubber gaskets, and be attached with screws for ease of replacement.

2. All module windows to be dark tinted. The curbside door window shall be 18.75" x 18.75" with fixed glass.

3. Twelve (12) 11.125" x 18.75" windows with fixed glass and dark tint, four (6) on the curbside of the module and five (6) on the streetside of the module, shall be installed just above seat backs.

4. One (1) rear door window shall be 11.125" x 18.75" window with fixed glass, dark tinted.

5. Each window shall have a 14-gauge stainless steel perforated security panel covering the window held in place with rivets.

6. No additional tint to be added to the Driver/Passenger Cab windows.

1. Heavy duty durable triple steps shall be provided and mounted under the curbside and rear passage doors.

2. Steps shall be wired to automatically extend and retract when door opens and closes.

3. A step-down warning light shall be installed in the dash to indicate steps are out.

4. Warning light shall be neutral safety controlled.

Two (2) roof mounted emergency egress hatches shall be installed. Padlocks shall be provided and installed by DOC.

Four (4) "gas ports" openings shall be installed, two (2) on each side of the module. Each port shall have a small box pan formed door with a locking paddle latch. Final locations and design to be determined at preconstruction meeting.

(Separate From the Cab and Chassis)

1. The module shall incorporate a combination heating/air conditioning system designed to maintain 70°F conditioned air temperature throughout the module in outside temperatures ranging from 20°F to 100°F. The system shall be easily accessible for maintenance.

2. The evaporators shall be located against the ceiling, one each side of the module, open seating area. The system shall have an automated thermostat and fans. Module temperature shall be settable from the cab with digital thermostat independent of the cab system. There shall be no more than 7 degrees temperature variation throughout the module. There shall be a digital display in the cab to show the air return temperature in the module. The condenser shall be located on the module roof.

3. The heater/AC conditioned air supply ducts shall run at ceiling level the entire length of the module on both sides of the module to ensure uniform distribution of conditioned air and uniform air temperature throughout the module. Evaporator units shall have perforated return air closeouts painted to match module interior and held in place with security screws. Closeouts shall be designed for access between interior wall sections.

Four (4) motor powered exhaust vents shall be provided at the rear of the vehicle. Exhaust vents shall be controlled via a switch located on the Driver's Console.

1. Bench seats in isolation cells shall be angled in to provide maximum foot room. All benches shall be covered with polyurethane and painted to match the interior. Benches/seats may be covered with a more durable textured polyurea thermoplastic elastomer.

2. Eleven (11) Freedman Seating # CITI-36223-2Prig gray 36” W two-person prison bench seats with mounting hardware.

3. Two (2) 34” L x 10” D flip-up aluminum benches painted to match interior. The benches shall have four (4) spring-loaded seat irons to keep the bench upright except during use. The walls at the mounting bracket shall be reinforced at the mounting location to support seat.

4. Seat belts are not required.

1. An Icon WT2472 20-gallon freshwater tank shall be installed under the bench in Cell #8 with an access panel on the forward wall of the lavatory (Cell #7) to provide maintenance access.

2. An exterior city water inlet port shall be installed on the curbside, above Compartment #8, to fill the tank.

3. A Shurflo #4048 RV style bypass electric water pump with Shurflo 255 series strainer shall be installed. The pump shall be mounted in Compartment #8. The pump shall be plumbed with ½: minimum flexible water line designed for the intended purpose. The outlet of the pump shall be plumbed to the toilet through the vacuum breaker supplied with the toilet to prevent backflow of water.

1. A Microphor #LF-320 12 VDC stainless steel toilet with push button flush shall be installed in the lavatory (#7).

2. The floor of the lavatory shall be stainless steel and extend up the walls 36-inches.

3. A drain shall be installed in the floor, with a duckbill valve.

4. A Kingsway Group #KG23 ligature-resistant two roll surface mounted toilet paper dispenser shall be installed in the lavatory (#7)

5. A 20-gallon fresh water tank shall be installed under the bench in Cell #8, with an access panel on the forward wall of the lavatory to provide maintenance access.

6. A 25-gallon black water tank shall be installed below the lavatory floor, with an exterior RV-style waste outlet connection.

7. A painted aluminum half-wall with hinged latching door shall be installed for privacy and security.

1. All added body and chassis electrical equipment shall be served by circuits separate and distinct from the vehicle chassis circuits.

2. All vehicle wiring shall be copper and conform to all SAE J1128 requirements. The wiring shall be colored, numbered, or function coded every 3: or permanent identification and correspond with the vehicle schematics.

3. Slotted Panduit-style wiring duct shall be used in electrical component module to ensure air circulation throughout power component wiring.

4. The wiring should be routed in conduit or looms and wiring shall be secured to the underbody or frame with insulation metal cable straps.

5. All power distribution cabling shall be covered with a protective split loom. Where wiring passes over exhaust, a heat shield shall be installed.

6. The electrical component module shall be equipped with positive locking plugs to provide easy disconnect for remount or repair of the body.

7. All wiring devices, switches, outlets, ect., except circuit breakers, shall be rated to carry 125% of the maximum ampere load for which the circuit is protected.

8. The vehicle electrical system shall be tested and certified to AMD 005 requirements.

Driver’s Console shall be installed between the seats and made of formed aluminum with black powder coating. The Driver’s Console shall have a switch panel with the following layout and a map holder with three (3) dividers that are mill finished aluminum. Cup holders shall be installed aft of the switch plate. All switches shall be wired ignition hot.

SWITCHES

1. Left Scene

2. Right Scene

3. Rear Scene

4. Flashers

5. Exhaust Vent

6. Exhaust Vent

7. Blank

8. Blank

OTHER:

1. Step down warning light

2. Passage door open warning light

3. Compartment door open warning light

4. ACC Climate Control Panel

5. Security Monitor, mounted off the curbside forward comer of console

6. Space for DOC supplied and installed recessed Motorola APX 8500 remote head On/Off switch for DVR.

1. Shall be designed to keep vehicle height to a minimum without interfering with the structural integrity of the roof.

2. Module interior lighting shall consist of thirteen (13) recessed lights. There shall be one (1) light in the entry, one (1) in each passenger cell and bathroom (7 total), four (4) in the aisle, and one (1) in the rear storage area.

3. Lights shall be Vista Cygnus #470268 dual intensity LED recessed lights installed with Tamper proof rings. The lights shall be activated by an on/off switch labeled “DOME” on the driver’s console, or by the exterior doors.

1. Shall include headlights, parking lights, directional signal lights, tail and stop lights, license plate light, back-up lights, side marker lights, hazard and warning lights, and clearance lights as required by FMVSS 108.

2. Rear stop, turn, side marker, and back-up lights shall be "Truck-Lite" sealed units. Red and Amber module clearance lights shall be "Truck-Lite" sealed lights.

3. Two (2) LED Whelen #70BTT stop/taillights shall be installed on the rear of the module, one (1) each side midway up.

4. Two (2) LED Whelen #70A00TAR turn arrows shall be installed on the rear of the module, one (1) each side, directly under stop/taillights.

1. Four (4) NMO universal antenna mounts with KHFUD cables and Larsen HyPer master universal connectors and mini-UHF adapters shall be installed on the module.

2. Antenna base access shall be through the dome light openings, and the cables shall terminate in the upper portion of compartment No. 1.

An LED strip light shall be installed in all outside compartments and shall be activated by a door switch.

FLASHERS

1. Four (4) Whelen #70A02FCR Clear lens Amber LED Flashers shall be installed, two

(2) on each side in the upper comers.

2. Four (4) Whelen 70RA6FCR Clear lens Red/Amber split LED flashing lights shall be installed, one (1) on each side in the rear upper comers, one (1) on each side in the front of the module in the front upper corners.

3. Two (2) Whelen #70R02FCR Clear lens Red Super LED flashers shall be installed on each side of the module above the wheel well.

4. Two (2) Whelen #WIONSMCK Clear lens Red/Amber Split LED flashers will be installed on the OEM grille.

5. Lights shall be controlled by the “FLASHER” switch on the driver’s console.

SCENE LIGHTS

1. Six (6) Whalen #70C0ELZR LED scenelights shall be installed - two (2) on each side and two (2) on the rear of the module, inboard of the flashers.

2. Rear lights shall automatically turn on when vehicle is placed in reverse.

3. Curbside scene lights shall automatically turn on when either passage door is opened.

4. Scenelights shall be controlled by the respective switches on the driver’s console

1. Four (4) module speakers shall be provided and connected for use with the cab radio via a Precision Power PPI S200.2 amplifier head on the rear console. The Precision Power head shall allow voice commands via the microphone, or signal input from cab radio.

2. A BNW-supplied minimum two-channel amplifier shall be installed, in Compartment #1. A volume knob shall be installed on the rear console for independent control of cab radio volume.

3. A metal grating shall be installed over the speaker to protect from vandalism.

4. Module speakers shall be independently controlled from the cab speakers.

5. A Precision Power PPI S200.2 2-Channel amplifier shall be DOC provided for the speakers.

6. Amplifier shall be installed in a location to be determined by DOC.

1. Security system shall include a minimum of eleven (11) and a maximum of sixteen (16) color camera channels with low light capability with separate Omni-directional microphones shall be installed in the module and exterior of module (location determined by DOC) with protective covers in locations to be determined by DOC. (Cameras with built-in microphones are acceptable)

2. There will be a minimum of eleven (11) interior cameras to include one facing the entrance and one on the front bulkhead facing the rear.

3. The microphones shall allow for high and low frequency cutout. Audio from the microphones shall be cleaned to reduce background noise within the prisoner module.

4. Audio and Video from the cameras and Microphones shall be recorded on an appropriately sized DVR with four (4) Terabytes of memory. The DVR shall be installed in a location to be determined by DOC.

5. A twenty-one (21) inch LCD display shall be mounted in the cab with built in speakers and a 3.5mm headphone output.

6. Requiring an exterior and back-up camera system. Rosco back-up sensors on the rear of the vehicle with an in-cab visual/audible display, and an FRC inVIEW 360 HD 360-degree exterior camera system with 1 TB of recording capability and monitor with multiple display options, including top-down, side, and back-up views.

Operation:

1. All camera (minimum of 11 and maximum of 16) feeds shall be viewed on the monitor. By using the touchscreen, the officer can select a camera to view full screen while still recording from all the cameras.

2. Capability from the monitor to add an "event" marker in the recording for later review.

3. Administrator capability shall allow operator rights as well as the ability to change menu options available to the operator, download/backup video, and select specific video channels or all video channels.

1. Bidder’s price includes delivery of the vehicle to DOC in Washington State. (Bid price is FOB destination)

2. The vehicle shall be tested and approved prior to delivery, and all records shall be submitted at time of delivery.