DESV_Submittal.pdf

DESV with Extended Casing Single Duct Terminal Unit Digital, Pressure Independent

Size CFM Range D (H x W) C F G H L M W CH CL CW

5E 0-350 4 7/8 6 2 1/8 7 3/8 10 15 1/2 3 3/8 12 12 1/4 18 6 1/2

6E 0-500 5 7/8 6 2 1/8 7 3/8 10 15 1/2 3 3/8 12 12 1/4 18 6 1/2

7E 0-650 6 7/8 7 1 1/8 5 3/8 12 1/2 15 1/2 3 3/8 14 12 1/4 18 6 1/2

8E 0-900 7 7/8 7 1 1/8 5 3/8 12 1/2 15 1/2 3 3/8 14 12 1/4 18 6 1/2

1E 0-1400 9 7/8 8 - 5 3/8 15 15 1/2 3 3/8 16 12 1/4 18 6 1/2

2E 0-2000 11 7/8 10 - 3 3/8 17 1/2 15 1/2 3 3/8 20 12 1/4 18 6 1/2

4E 0-3000 13 7/8 12 - 3 3/8 18 15 1/2 3 3/8 24 12 1/4 18 6 1/2

This submittal is meant to demonstrate general dimensions of this product. The drawings are not meant to detail every aspect of the product. Drawings are not to scale. Titus reserves the right to make changes without written notice.

All rights reserved. No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Air Distribution Technologies, Inc.

Submittal DESV - 1.0 2-14-2025

CW

CL

Slip & Drive Cleat Connection

Control Enclosure (Optional on Cooling-only units)

LM

G

CH

D

C F

F W

H

Digital Control, DESV

Right hand unit shown. All dimensions are in inches.

This submittal is meant to demonstrate general dimensions of this product. The drawings are not meant to detail every aspect of the product. Drawings are not to scale. Titus reserves the right to make changes without written notice.

All rights reserved. No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Air Distribution Technologies, Inc.

Accessories (Optional)

• The DESV with Extended Casing utilizes a larger casing than a standard DESV model. When accompanied with a matching hot water reheat coil, heating performance can be improved.

This is especially true when low entering water temperature is used.

• Heavy gauge G40 galvanized steel housing. Mechanically sealed and gasketed, leak resistant construction. Less than 2% of nominal cfm at 1.5” sp wg.

• Dual density internal insulation, treated to resist air erosion. Meets

24 V Control Transformer Dust Tight Enclosure Seal Fibre Free Liner ½” EcoShield Liner ½” Fibre Free Liner

Check if provided. 1” Fiberglass Liner 1” EcoShield Liner 1” Fibre Free Liner Low Leakage Seal/Test Certify SteriLoc Liner

UltraLoc Liner ½” EcoShield Liner (Foil Face) 1” EcoShield Liner (Foil Face) Disconnect Switch Hanger Brackets

Removable Air Flow Sensor Bottom Access Door OSP & IBC -S Seismic Certification Red List Compliant “Google” Gasketing Stainless Steel Construction requirements of NFPA 90A and UL 181.

• Units equipped with the Titus II velocity controller can either be direct acting or reverse acting, with the damper either normally open or normally closed. Controller maintains constant span and start point. (Span and start point are adjustable.)Rectangular discharge opening is designed for slip and drive cleat duct connection.

• Multipoint center averaging inlet velocity sensor.

• Control packages can be factory mounted by Titus.

• Choice of right hand or left hand control location.

• Units equipped with the Titus I velocity controller are available in both direct acting / normally open and reverse acting / normally closed operating modes.Model DESV without coils can be installed horizontally, vertically, or at any angle.

Operation is not affected by position. For units with coils, consult technical support.

OSP 0352-10

• Only Titus Alpha controls approved for seismic installation.

Submittal DESV - 2.0 2-14-2025

General Description

39 1/2 6 1/2 W

12 1/4 H

Integral Sound Attenuator

DESV

Hot Water Coil Section

on 1 row coils and 5/8” OD on 2 row coils. Unit sizes 09-40: 7/8” OD for all coils

the discharge of attenuator.

• Coils rated and certified to AHRI Standard 410

1 Row 2 Row 3 Row 4 Row

H

L W

This submittal is meant to demonstrate general dimensions of this product. The drawings are not meant to detail every aspect of the product. Drawings are not to scale. Titus reserves the right to make changes without written notice.

All rights reserved. No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Air Distribution Technologies, Inc.

Accessories (Optional)

Submittal DESV - 3.0 2-14-2025

Standard Features

• Single side access to low voltage, high voltage, and electric heater controls.

• Automatic reset thermal cutouts, one per element.

Options Supply Voltage Fuse Block Disconnect switch, door interlock type Dust tight construction

120V, 1ph, 60Hz 208V, 1 ph, 60Hz 240V, 1 ph, 60Hz

277V, 1 ph, 60Hz 208V, 3 ph, 60Hz 480V, 3 ph, 60Hz (4 wire wye standard)

The total length of the DESV unit is the summation of the unit length (with or without attenuator) and the length of the optional water coil.

Size H W Water Coil

L 5E 8 12 7 1/4 6E 8 12 7 1/4 7E 10 12 7 1/4 8E 10 12 7 1/4 1E 12 1/2 14 7 1/4 2E 12 1/2 14 9 3/4 4E 12 1/2 20 9 3/4

Electric Coil Section Optional SCR Controlled Electric Heater Optional Lynergy Controlled Electric Heater

36 5/8”

39 1/2” 6 1/4” W

H12”