APPENDIX C.pdf

Improve Site Access and Physical Security Deficiencies VA Central California Healthcare System, Fresno, CA

VA Project Number: 570-19-107

APPENDIX C

INTERIOR FINISHES CUT

SHEETS

TECHNICAL DATA

Wilsonart® Solid Surface

Copyright 2020, Wilsonart LLC

1. Manufacturer

Wilsonart LLC 2501 Wilsonart Drive P.O. Box 6110 Temple, Texas 76503-6110 Phone: (254) 207-7000; (800) 433-3222 Fax: (254) 207-2384 Web Site: www.wilsonart.com

2. Product Description

Recommended Uses Wilsonart® Solid Surface is recommended for interior application use and has a wide range of vertical and horizontal applications. Common design elements are decorative wall panels, shower surrounds, countertops, vanities, retail countertops, healthcare countertops, and window sills.

Product Composition Wilsonart® Solid Surface is manufactured with acrylic resins, fire-retardant fillers and proprietary coloring agents that are homogeneous, with uniform color throughout their thickness.

Patterns & Colors Color and pattern are uniform for the entire material thickness and sheets are color matched to adjacent solid surface sheets within the same lot reference.

Wilsonart Product Type Colors/Patterns 051 70+

025 D354SL, 1573SL, 1530TM

*Please contact your Wilsonart® Solid Surface distributor for additional availability of special order patterns in Product Type 025. Minimum order quantities will apply for special orders, and require eight to ten weeks for delivery.

Finishes Final finish (sheen) for surfaces ranges from matte to high gloss. Surfaces with gloss and semi-gloss finishes require more maintenance than matte or satin finishes. Darker colors will require special attention.

Standard Sheet Sizes Wilsonart Product Type Thickness Width Length

1/2 inches or 0.490 inches (1.25 cm)

± 0.025 inches (0.06 cm) 30 inches (76.2 cm)

144 inches (365.8 cm)

051 1/2 inches or 0.490 inches (1.25 cm) ± 0.025 inches (0.06 cm)

60 inches (152.4 cm)

144 inches (365.8 cm)

025 1/4 inches 0.240 inches (0.61 cm) ± 0.015 inches (0.38 cm)

60 inches (152.4 cm)

98 inches (248.92 cm)

NOTE: Sheets may be approximately one-quarter inch (6mm) longer and wider than above measurement.

http://www.wilsonart.com/

Copyright 2020, Wilsonart LLC

Special Orders Wilsonart® Solid Surface is available in other sizes. Minimum order quantities apply and require eight to ten weeks for delivery. Please contact your local Wilsonart Representative for complete order requirements.

3. Technical Data

051 Solid Surface Properties Typical Results Test

Tensile Strength 6800 psi* ASTM D 638

Tensile Modulus 1.5 x106 psi ASTM D 638

Tensile Elongation 0.4% min. ASTM D 638

Flexural Strength 10,400 psi* ASTM D 790

Flexural Modulus 1.73 x106 psi ASTM D 790

Thermal Expansion Coefficient 1.37 x10-5 in./in./°F ASTM D 696

Hardness (Barcol Impressor) 60 ASTM D 2583

Impact Resistance 144 in. drop A ISO 4586

Izod Impact 0.28 (ft-lb.)/in ASTM D 256 Method A

Light Resistance - Xenon No effect ISO 4586

Stain Resistance Pass ANSI Z-124.3 modified

Wear and Cleanability Pass ANSI Z-124.3

Fungi Resistance Pass ASTM G 21

Bacterial Resistance Pass ASTM G 22

Boiling Water Resistance No effect ISO 4586

High Temperature Resistance No effect B ISO 4586

Weatherability ∆E<5 ASTM G 155

Moisture Absorption <0.25% ASTM D 570 Long Term

Specific Gravity 1.7 gram/cm3 ASTM D 792

Approximate Weight 4.4 lb./ ft2

Fire Behavior Class 1 and Class A ASTM E 84

* Test results vary slightly depending on pattern.

A No fracture B High temperature resistance tests may have an effect on the surface; however, the surface can be renewed to ‘No Effect’.

025 Solid Surface Properties Typical Results Test

Thermal Expansion Coefficient 1.50 x10-5 in./in./°F ASTM D 696 696696696

Hardness (Barcol Impressor) 62 ASTM D 2583

Impact Resistance 78 in. drop A ISO 4586

Izod Impact 0.24 (ft-lb.)/in ASTM D 256 Method A

Light Resistance – Xenon No effect ISO 4586

Stain Resistance Pass ANSI Z-124.3 modified

Wear and Cleanability Pass ANSI Z-124.3

Fungi Resistance Pass ASTM G 21

Bacterial Resistance Pass ASTM G 22

Boiling Water Resistance No effect ISO 4586

High Temperature Resistance No effect B ISO 4586

Weatherability ∆E<5 ASTM G 155

Moisture Absorption <0.25% ASTM D 570 Long Term

Specific Gravity 1.78 gram/cm3 ASTM D 792

Approximate Weight 2.2 lb./ ft2

Fire Behavior Class II and Class B ASTM E 84

* Test results vary slightly depending on pattern.

A No fracture B High temperature resistance tests may have an effect on the surface; however, the surface can be renewed to ‘No Effect’.

The information contained in this section is based on technical data which Wilsonart LLC believes to be reliable, and is intended for use by persons having knowledge of this technical area at their own discretion.

Physical Properties of Solid Surface Wilsonart® Solid Surface is highly resistant to impact fracturing and elevated temperatures. The material has very low moisture absorption, does not support fungal or bacterial growth, and is stain resistant. Refer to Wilsonart Guide Specifications for a complete list of physical properties and test results.

Typical Flame Spread and Smoke Developed Properties Wilsonart® Solid Surface ½-inch is Class I and Class A rated. Wilsonart® Solid Surface ¼-inch is Class II and Class B rated. Ratings are achieved using ASTM E 84 test procedures.

Codes and Certifications Wilsonart® Solid Surface has achieved the following:

• FDA Compliance for food contact

• New York City Material Equipment Acceptance numbers 181-96-M

• NSF 51 Food Zone and FDA food contact compliant.

• UL GREENGUARD® Gold Certified for low chemical emissions.

• LEED® 2009 potential credits can be obtained in the Commercial Interiors category for the following:

‒ IEQ 4.1 Low-Emitting Materials

• Wilsonart® Hard Surface Adhesive is UL GREENGUARD Gold Certified for low chemical emissions and SCAQMD Rule 1168 compliant for VOC content. Wilsonart® Color Matched Caulk meets the SCAQMD standard.

https://wilsonart.box.com/shared/static/1c12uela36tjgaqtlgfc97zqlw79ruvj.pdf

Branded Cleaner and Sanitizer Resistance for Wilsonart® Solid Surface No effect was exhibited except as noted (* or **) on the following:

Cleaner or Sanitizer Effect

Removed with Water

Effect Removed with

Water and Scotch- Brite®

Effect Removed with

Finishing & Sanding Process

Clorox Healthcare Bleach Germicidal Cleaner** X Clorox Healthcare Versa Sure Cleaner Disinfectant Wipes* X Oxivir TB** X Oxivir 1** X Virex II 256 X Benefect** X PDI Super Sani-Cloth Germicidal Disposable Wipes X PDI Sani-Prime Germicidal Spray X Expose II 256* X Stride Floral Neutral Cleaner* X PURELL Advanced Instant Hand Sanitizer* X

Test procedure: Listed materials were placed in contact with Wilsonart® Solid Surface under 1" (25.4mm) diameter watch cover glass for 16 hours duration prior to evaluation for effect. The branded cleaners and sanitizers listed above were cleaned with water only.

* Causes slight change of gloss or color.

** Causes slight damage, with degree of damage proportionate to length of exposure and concentration.

The effect of some reagents, cleaners, and/or sanitizers may require further refinishing efforts in order be removed. The refinishing effort required will depend on the concentration, temperature, and length/frequency of exposure.

Finishing guidelines can be located in the Wilsonart Solid Surface Fabrication and Installation manual and are recommended to be conducted by a certified fabricator.

4. Installation: Fabrication and Assembly Recommendations

Refer to Wilsonart® Solid Surface Fabrication Manual and Wilsonart Fabrication Drawings for detailed information.

5. Warranty

6. Maintenance

7. Technical Services

For samples, literature, questions or technical assistance, please contact our toll-free Hotline at (800) 433-3222, Monday through Friday, 8 am – 5 pm, CST.

https://wilsonart.box.com/shared/static/hwfgyhu03c83o1rzatxh306ltswvagyc.pdf https://wilsonart.box.com/s/jyn1bpi9nn7ysshri2jtgmtfibp0kaxl http://www.wilsonart.com/resources?category=Solid%20Surface&document_type=Warranty https://wilsonart.box.com/shared/static/b5qczzqtadeta5vlzc3pj8voolxygcwm.pdf

Specification Form:

Surface shall be Wilsonart® Solid Surface, produced by Wilsonart LLC, Temple, Texas 76503-6110

Type:

Surface Color Number: ______________ Color Name: _______________

Finish Number: ______________ Name: _____________________

Adhesive Name: ______________ Grade/Type: ______________ Brand: Wilsonart® Adhesive

Wilsonart Solid Surface Technical Data Revised: September 14, 2020 © 1998-2020, Wilsonart LLC

© 2020, Wilsonart LLC

TECHNICAL DATA

Wilsonart® Laminate Basic Types 107, 335, 350

1. Manufacturer

Wilsonart LLC 2501 Wilsonart Drive P.O. Box 6110 Temple, Texas 76503-6110 Phone: (254) 207-7000; (800) 433-3222 Fax: (254) 207-2384 Web Site: www.wilsonart.com

2. Product Description

Recommended Uses Wilsonart® Laminate, types 107, 335, and 350, is suitable for use on fine quality residential and commercial furniture, fixtures and casework, and for architectural application on columns, wainscoting, valances, cornices, interior doors and divider systems.

General Purpose (HGS) Type 107 is most frequently used for work surfaces on counters, islands, vanities, desks and tables. Typical vertical uses include surfacing for wall panels, teller cages and the front panels of workstations, such as those in hospitals, airports and restaurants. Type 107 is produced for both horizontal and vertical interior applications where the surface must be functional, durable and decorative.

Vertical Surface (VGP) Type 335 is the usual choice to surface cabinet walls, doors and drawer panels.

It often appears on the vertical surfaces of desks, restaurants booths and maître d’ stations, and as architectural cladding. Type 335 is intended for vertical applications where a functional, durable, decorative surface must absorb somewhat less impact than a comparable horizontal surface. VGP surfaces may be postformed to achieve radius edges.

Postforming (HGP) Type 350 adds the decorative capability of a soft edge to any typical laminate use.

Common applications of postforming laminates are formed edges for counters, desktops, cabinet doors and drawer panels. Type 350 is intended for use on vertical and horizontal interior surfaces where it is necessary or desirable to roll the laminate on a simple radius over the edge of the substrate. This eliminates seams and leaves an attractive surface.

Wilsonart® HD® finishes feature Antimicrobial Protection that helps inhibit the growth of stain and odor causing bacteria, mold, and mildew on your countertop or surface. Wilsonart’s Antimicrobial Protection won’t wash away or wear off. Premium and Standard finishes are available with Antimicrobial Protection upon request during the ordering process.

Product Composition Decorative surface papers impregnated with melamine resins are pressed over Kraft paper core sheets impregnated with phenolic resin. These sheets are then bonded at pressures greater than 1000 pounds per square inch at temperatures approaching 300F (149C). Finished sheets are trimmed, and the backs are sanded to facilitate bonding.

Basic Limitations Wilsonart® Laminate is for interior use only and is not recommended for direct application to plaster, concrete walls, or gypsum wallboard. It is not structural material and must be bonded to a suitable substrate.

Do not subject Wilsonart® Laminate to extremes in humidity or temperatures higher than 275F (135C) for substantial periods of time, or intense, continuous, direct sunlight.

file:///C:/Users/leonars/AppData/Local/Microsoft/Windows/Temporary%20Internet%20Files/Content.Outlook/YTAUW2IK/www.wilsonart.com

Patterns & Colors Available in a full range of solid colors, stones, marbles, woodgrains, leathers and patterns. See all designs at www.wilsonart.com. Please see actual sample before specifying.

Finishes Confirm finish availability on individual designs by going to www.wilsonart.com

#01 High Gloss - Premium A mirror sheen finish, which gives a smooth, brilliant appearance. #01-High Gloss finish also features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Can be used for horizontal applications such as countertops and light-to-medium commercial applications. Excellent for vertical applications. Nominal Glossometer Reading = 110

#05 Timbergrain - Premium An overall finish with dimensional low-sheen, realistic ticking and natural variation across the sheet, looks very much like the surface of natural wood veneer. #05 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 4.5

#07 Textured Gloss - Premium A textured finish which reproduces the high sheen of waxed wood furniture. #07 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 42

#12 SoftGrain - Premium A dense wood grain structure that is low gloss and soft to the touch. Subtle highlights of reflectivity randomly occur within the embossed grains, creating a sophisticated raw wood look. #12 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 8

#15 Fieldstone - Premium A matte, stone finish with a mixture of low sheen, stone-like textural attributes layered across the surface;

and layered on top are fine, irregular veins and features in a higher sheen, which create natural contrast and dimensional organic detail. It Includes AEON™ Enhanced Scratch and Scuff Resistant Performance Technology.

Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 3 #16 Casual Rustic - Premium A woodgrain texture with a blend of grain variations ranging from linear to subtle movement with random, irregular features. The overall low gloss surface is accented with higher sheen woodgrain ticking and random highlights. #16 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 6 #18 Linearity - Premium A directional texture running the length of the sheet, having a narrow, random and matte-gloss linear quality. It is complementary to linear woodgrains, and linear patterns (such as the “Satin” series), and provides dimension and visual movement to solid colors. #18 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 18 #19 Leno Weave – Premium Random intersecting horizontal and vertical lines create a geometric weave with a matte-gloss finish.

Recommended for horizontal and vertical applications. #19 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 15 #21 Soft Silk – Premium A smooth, ultra-matte finish with a silky, soft touch. This minimalist finish gives the surface a genuine stone feel. Recommended for horizontal and vertical applications. #21 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 8 http://www.wilsonart.com/laminate/design-library

#22 Antique - Premium A mixture of varying low gloss features combined with organic movement, indicative of the surface of an aged stone or an antique metal. Antique features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 9 #28 Gloss Line - Premium A linear woodgrain texture with varied widths of narrow grain structures in an alternating mix of matte and gloss surfaces areas. Gloss Line features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 5

#35 Mirage-Wilsonart® HD® Subtle variations in matte and gloss finish connect to nature’s own finishes: rough and weathered, smooth and polished. #35 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Gloss Reading = 50

#38 Fine Velvet Texture A smooth textured finish with moderate reflective value. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 14

#52 Quarry - Premium Premium finish emulating the “pitted” look of polished natural stone. #52 features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 55

#55 Glaze-Wilsonart® HD® A layering of matte features over a semi-gloss glaze, creates this timeworn effect. #55 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical application. Nominal Gloss Reading = 25

#57 Aligned Oak – Wilsonart® HD® Authentic realism is brought to the surfaces using synchronized texture as each elegantly aged oak design exhibits the natural dimension and feel or real world. #57 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 7 #60 Matte - Standard Textured finish with a moderate reflective quality. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 10

#78 FineGrain - Premium The FineGrain premium finish features the polish and luxe of a real wood veneer, with a subtle, narrow grain structure that runs the length of the sheet. #78 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 38

#79 Ridgewood – Premium An overall matte finish with ridged dimensional features creating a linear woodgrain effect. #79 finish features AEON™ Enhanced Scratch & Scuff-Resistant Performance Technology. Recommended for horizontal and vertical applications. Nominal Glossometer Reading = 4.5

NOTE: Nominal Glossometer readings are made at a 60 angle of incidence.

Finish Availability: Not all finishes are available in all patterns and colors. Some finish options have limited size availability. Please check with your Wilsonart representative or consult the pattern availability lookup on our website at www.wilsonart.com, to verify size availability by finish type.

Standard Sheet Widths 36” 48” 60” 914mm 1219mm 1524mm

Standard Sheet Lengths 96” 120” 144” 2438mm 3048mm 3658mm

NOTE: Not all sizes are available from stock; contact your Wilsonart representative for details on local availability. Minimums apply to non-standard designs and finishes in sizes other than 48”x96” and 60”x144”. Please check with your Wilsonart representative.

Thickness and Weight Description 107 335 350

Thickness 0.045” ± 0.005” (1.14mm ± 0.13mm)

0.028” + 0.001 - 0.004” (0.71mm + 0.03 - 0.10mm)

0.036” ± 0.005” (0.91mm ± 0.13mm)

Weight per square foot

0.328# 0.186# 0.260#

3. Technical Data

Physical Properties of General Purpose Laminates

ISO 4586 Test Typical Wilsonart Type 107 ISO 4586-3 HGS

Thickness 0.045” 0.005” (1.14mm 0.13mm) N/A

Appearance N/A N/A

Light Resistance Slight effect Slight Effect

Cleanability (cycles) 10 10

Stain Resistance Reagents 1-10 Reagents 11-15

No effect Slight effect

No effect Moderate effect

Boiling Water Resistance Slight Effect (Gloss) No Effect (Other Finishes)

Slight Effect (Gloss) No Effect (Other Finishes)

High Temperature Resistance Slight effect Slight Effect (Gloss) No Effect (Other Finishes)

Impact Resistance 65” (1651mm) 31.5” (800mm)

Radiant Heat Resistance 210 seconds > 200 sec.

Dimensional Stability Machine Direction Cross Direction

0.3% 0.7%

1.1% (max.)

1.4% (max.)

Surface Wear Resistance (cycles)

Meets or Exceeds 400 350 (min.)

Formability Not applicable Not applicable

Blistering Not applicable Not applicable

Physical Properties of Vertical Surface Laminates

ISO 4586 Test Typical Wilsonart Type 335 ISO 4586-3 VGP

Thickness 0.028” + 0.001 - 0.004” (0.71mm + 0.03 - 0.10mm) N/A

Appearance N/A N/A

Light Resistance Slight effect Slight effect

Cleanability (cycles) 10 20 (max.)

Stain Resistance Reagents 1-10 Reagents 11-15

No effect Slight effect

No effect Moderate effect

Boiling Water Resistance Slight Effect (Gloss) No Effect (Other Finishes)

Slight Effect (Gloss) No Effect (Other Finishes)

High Temperature Resistance Slight Effect (Gloss) No Effect (Other Finishes)

Slight Effect (Gloss) No Effect (Other Finishes)

Impact Resistance 40” (1016mm) 23.5” (600mm) Radiant Heat Resistance 200 seconds > 200 sec.

Dimensional Stability Machine Direction Cross Direction

0.5% 0.8%

1.1% (max.)

1.4% (max.)

Surface Wear Resistance (cycles)

Meets or Exceeds 400 350 (min.)

Formability 5/16” radius (7.93mm) 7/16” radius (11mm) 9/16” radius(14.7mm)

Blistering 45 seconds > 40 seconds

*Radius for face is actually the radius of the form around which the laminate is postformed. The radius for back is actually the radius to which the decorative face is postformed.

Physical Properties of Postforming Laminate

ISO 4586 Test Typical Wilsonart Type 350 ISO 4586-3 HGP

Thickness 0.036” 0.005” (0.91mm 0.13mm) N/A

Appearance N/A N/A Light Resistance Slight effect Slight effect Cleanability (cycles) 10 20 Stain Resistance Reagents 1-10 Reagents 11-15

No effect Slight effect

No effect Moderate effect

Boiling Water Resistance Slight Effect (Gloss) No Effect (Other Finishes)

Slight Effect (Gloss) No Effect (Other Finishes)

High Temperature Resistance Slight Effect (Gloss) No Effect (Other Finishes)

Slight Effect (Gloss) No Effect (Other Finishes)

Impact Resistance 55” (1397mm) 31.5” (800mm)

Radiant Heat Resistance 205 seconds > 200 sec.

Dimensional Stability Machine Direction Cross Direction

0.5% 0.8%

1.1% (max.)

1.4% (max.)

Surface Wear Resistance (cycles)

Meets or Exceeds 400 350 (min.)

Formability* *5/16” face (7.93mm) *3/8” back (9.52mm)

*9/16” face (14.27mm) *3/4” back (19.05mm)

Blistering 65 seconds > 40 seconds *Radius for face is actually the radius of the form around which the laminate is postformed. The radius for back is actually the radius to which the decorative face is postformed.

Typical Fire Test Data High-pressure laminates are subject to flame spread and smoke developed standards in structures where codes establish such conditions.

Test data to determine compliance with these codes are obtained by the Steiner Tunnel Test method of the American Society for Testing Materials (ASTM-E-84, Standard Test Method for Surface Burning Characteristics of Building Materials). Tests were conducted in accordance with test method and mounting procedure as described in paragraph X1.7.2 of the test method. This procedure is cataloged by Underwriters Laboratories, Inc. as UL 723. Here is typical data for Wilsonart® Laminates, averaged from two specific tests:

Typical Flame Spread and Smoke Developed Properties

Product Type Test Condition Flame Spread Smoke Developed

General Purpose Type 107 Unbonded 50 45

Vertical Surface Type 335 Unbonded 45 40

Postforming Type 350 Unbonded 60 35

General Purpose Type 107 Bonded with contact adhesive to particleboard substrate; 3/8” 40 100

Vertical Surface Type 335 Bonded with contact adhesive to particleboard substrate; 3/8” 40 155

Postforming Type 350 Bonded with contact adhesive to particleboard substrate; 3/8” 50 140

When you wish to specify decorative laminate for a Class I or A fire rating, please refer to the Fire- Rated Laminate Tech Data.

Model Code Designations used to determine flame spread classification Flame Spread Classification (Max. Rating)

International

(IBC)

Life Safety

(NFPA 101)

25 A A 75 B B 200 C C

RE: Architectural Woodwork Quality Standard, 8th Edition, Version 1.0, - 2003

All Model Codes regulate the generation of smoke by interior finish material. In all cases they specify a maximum smoke development rating of 450.

Codes and Certifications

General Standards Wilsonart® Laminates, types 107, 335 and 350, conform to the voluntary standards of the American National Standards Institute, for thickness, performance properties and appearance. Wilsonart® Laminates 107,335 and 350 meet or exceed the International Standards Organization specifications as found in ISO 4586, titled “High-Pressure Decorative Laminate (HPDL) – Sheets Based on Thermosetting Resins – Part I: specifications.”

Specific Product Standards U.S. Federal Specification L-P 508H, April 9, 1977, “Plastic Sheets, Laminated, Decorative and Non-decorative.” Spells out criteria for decorative laminates for federal installations. Wilsonart 107, 335 and 350 laminates comply.

NSF International (NSF) #35 “Laminated Plastic for Surfacing for Food Service Equipment.” All solid colors and printed patterns in Basic Types 107, 335 and 350, comply.

U.S. Federal Register, August 9, 1984, Housing and Urban Development Mobile Home Construction and Safety Standard, (24CFR) 3280.203. General Purpose Type 107 and Vertical Surface Type 335 comply.

U.S. Federal Test Method, Federal Aviation Regulation, DOT, Part 25.853, Airworthiness Standards:

Transport Category Airplane (Interior Finish). Vertical Surface Type 335 and Postforming Type 350 comply with parts A and C.

U.S. Federal Motor Vehicle Safety Standard (FMVSS) 302, “Flammability of Interior Materials.” Basic Types 107, 335 and 350 comply.

U.S. Military Standard MIL-P-17171E (SHIPS)/Plastic Laminate. General Purpose Type 107 complies.

Branded Cleaner and Sanitizer Resistance for Wilsonart® Laminate per ISO 4586-2 Method 31 (B) No effect was exhibited except as noted (* or **) on the following:

1. Beckart Environmental (Stabilized Chlorine Dioxide Mixed with Water at 3000ppm)

2. Benefect®

3. Claire® Germicidal Cleaner (Country Fresh Scent)

4. Claire® Disinfectant Spray Q (Country Fresh Scent)

5. Clean Republic – All Purpose Everyday Cleaner (Hypochlorous Acid – 0.003% Solution)

6. Clorox® Anywhere® Hard Surface Sanitizing Spray*

7. Clorox® Clean-Up (Cleaner & Bleach)

8. Clorox® Disinfecting Bleach w/6% Sodium Hypochlorite (24:1/Water:Bleach)

9. Clorox® Disinfecting Spray

10. Clorox® Disinfecting Wipes

11. Clorox Healthcare® Bleach Germicidal Cleaner *

12. Clorox Healthcare® Hydrogen Peroxide Cleaner Disinfectant

13. Clorox Healthcare® Fuzion® Cleaner Disinfectant*

14. Clorox Healthcare® VersaSure® Cleaner Disinfectant Wipes

15. Clorox® Total 360 Disinfectant Cleaner

16. Diversey™ Expose® II 256

17. Diversey™ Oxivir 1

18. Diversey™ Oxivir Tb Wipes

19. Diversey™ Stride® Floral Neutral Cleaner

20. Diversey™ Virex® II 256

21. Fabuloso® Complete (Multi-Purpose Cleaner)

22. Lysol® Professional Disinfectant Spray

23. Microban® 24 Hour (Multi-Purpose Cleaner)

24. PDI Sani-Prime® Germicidal Spray

25. PDI Super Sani-Cloth® Germicidal Disposable Wipes

26. Purell® Advanced Hand Sanitizer Gel

27. Purell® Food Service Surface Sanitizer

28. Purell® Professional Surface Disinfectant

29. Purell® Healthcare Surface Disinfectant

30. Simple Green® Concentrated (All-Purpose Cleaner)

31. Spic and Span® Everyday (Antibacterial Cleaner)

Test procedure: Listed materials were placed in contact with Wilsonart® Laminate surface under 1" (25.4mm) diameter watch cover glass for 16 hours duration prior to evaluation for effect. The branded cleaners and sanitizers listed above were cleaned with water only.

* Causes slight change of gloss or color.

** Causes slight damage, with degree of damage proportionate to length of exposure and concentration.

Branded Cleaner and Sanitizer Resistance for Wilsonart® Laminate per BIFMA HCF 8.1-2014 (Section 6 / Modified) No effect was exhibited except as noted (* or **) on the following:

1. Beckart Environmental, Inc. (Stabilized Chlorine Dioxide Mixed with Water at 3000ppm)

2. Benefect®

3. Claire® Germicidal Cleaner (Country Fresh Scent)

4. Claire® Disinfectant Spray Q (Country Fresh Scent)

5. Clean Republic – All Purpose Everyday Cleaner (Hypochlorous Acid – 0.003% Solution)

6. Clorox® Anywhere® Hard Surface Sanitizing Spray

7. Clorox® Clean-Up (Cleaner & Bleach)

8. Clorox® Disinfecting Bleach w/6% Sodium Hypochlorite (24:1/Water:Bleach)

9. Clorox® Disinfecting Spray

10. Clorox® Disinfecting Wipes

11. Clorox Healthcare® Bleach Germicidal Cleaner

12. Clorox Healthcare® Hydrogen Peroxide Cleaner Disinfectant

13. Clorox Healthcare® Fuzion® Cleaner Disinfectant

14. Clorox Healthcare® VersaSure® Cleaner Disinfectant Wipes

15. Clorox® Total 360 Disinfectant Cleaner

16. Diversey™ Expose II 256

17. Diversey™ Oxivir 1

18. Diversey™ Stride® Floral Neutral Cleaner

19. Diversey™ Tb Wipes

20. Diversey™ Virex II 256

21. Fabuloso® Complete (Multi-Purpose Cleaner)

22. Lysol® Professional Disinfectant Spray

23. Microban® 24 Hour (Multi-Purpose Cleaner)

24. PDI Sani-Prime® Germicidal Spray

25. PDI Super Sani-Cloth® Germicidal Disposable Wipes

26. Purell® Advanced Hand Sanitizer Gel

27. Purell® Food Service Surface Sanitizer

28. Purell® Professional Surface Disinfectant

29. Purell® Healthcare Surface Disinfectant

30. Simple Green® Concentrated (All-Purpose Cleaner)

31. Spic and Span® Everyday (Antibacterial Cleaner)

Test procedure: Listed reagent materials were placed in contact with Wilsonart® Laminate surface with a one-inch square 100% cotton cloth completely saturated and covered with a 2” (50.8mm) diameter watch cover glass for 15 minute duration. The reagents listed above were removed with clean cloth and the area was then cleaned with clean cloth and distilled water only. The surface area was allowed to dry for 1-hour prior to evaluation for effect.

* Causes slight change of gloss or color.

** Causes slight damage, with degree of damage proportionate to length of exposure and concentration.

Resistance of Furniture to UV Lights for Wilsonart® Laminate per BIFMA HCF 8.1-201X Section 9 (Alternate Method per ASTM G155 using ISO 4586-2.33 conditions).

Wilsonart® Laminates 107,335,350 and 376 conforms to BIFMA – Healthcare Furniture Design Guidelines for Cleanability, Section 9 Resistance to Furniture to UV Lights. Wilsonart® Laminates 107, 335, 350 and 376 meet or exceed the acceptance level for surface evaluation.

4. Installation: Fabrication and Assembly Recommendations

Fabrication should follow approved methods. Assembled pieces should meet the specifications of KCMA (Kitchen Cabinetmakers Manufacturers Association), ANSI A-161.2-1998 (revised), and “Architectural Woodwork Quality Standards, Guide Specifications and Quality Certification Program” guidelines of the Architectural Woodwork Institute where applicable.

Wilsonart® Laminates must be bonded to a substrate of reliable quality, such as particleboard, medium density fiberboard or plywood with one A-face. High-Pressure Laminate, plaster, concrete and gypsum board should not be considered suitable substrates. Basic Types laminate may not be used as structural members.

Bond with adhesives and follow the techniques recommended by the adhesive manufacturer.

Recommended adhesives are permanent types, such as urea and polyvinyl acetate (PVA), and contact types. Wilsonart adhesives are recommended for most bonding conditions.

To avoid stress cracking, do not use square-cut inside corners. All inside corners should have a minimum of 1/8” (3.175mm) radius and all edges should be routed smooth.

Drill oversized holes for screws or bolts. Screws or bolts should be slightly countersunk into the face side of a laminate-clad substrate.

Take care to ensure an appropriate acclimation between the laminate and the substrate prior to fabrication. The face and backing laminates and the substrate should be conditioned in the same environment for 48 hours before fabrication. Recommended conditioning temperature is about 75F (24C). Laminates should be conditioned at 45% to 55% relative humidity.

With postforming machinery, Wilsonart® Laminate types 335 and 350 will postform at a nominal sheet temperature range of 325F to 338F (163C to 170C) in 20 5 seconds.

Carbide-tipped saw and router blades should be used for cutting. High tool speed and low feed speed are advisable. Cutting blades should be kept sharp. Use a hold-down to prevent any vibration.

5. Warranty

6. Maintenance

7. Technical Services

For samples, literature, questions or technical assistance, please contact our toll-free Hotline at (800) 433-3222, Monday through Friday, 8 am – 5 pm, CST.

Specification Form:

Surface shall be Wilsonart Laminate, produced by Wilsonart LLC, Temple, Texas 76503-6110

Type: Specify 107, 335 or 350

Surface Color Number: ______________ Color Name: ______________

Finish Number: ______________ Name: ______________

Edge Trim Color Number: ______________ Color Name: ______________

Adhesive Name: ______________ Grade/Type: ______________ Brand: Wilsonart® Adhesive

Wilsonart® Laminate Technical Data Basic Types 107, 335, 350 Revised: October 1, 2021 © 1998-2021, Wilsonart LLC http://static.wilsonart.com.cdnga.net/sites/default/files/docs/resources/technical-information-warranty-wilsonart-laminate.pdf https://issuu.com/wilsonart/docs/wilsonart___care_and_maintenance_br?e=1726292/14175198

THASSOS WHITE

MARBLE M420 –

POLISHED

CARRARA WHITE

MARBLE M701 –

POLISHED

CHIARO BEIGE

MARBLE M710 –

POLISHED

ABSOLUTE BLACK

GRANITE G771 –

POLISHED

COLOR PALETTE

WINDOWSILLS & THRESHOLD

NATURAL

STONE

USAGE

NOT APPLICABLE

FOR ALL

PRODUCTS IN

THIS SERIES. SEE

CHARTS FOR

FULL PRODUCT

DETAILS.

WINDOWSILLS

THRESHOLDS – HOLLYWOOD BEVEL (SINGLE & DOUBLE)

THRESHOLDS – DOUBLE BEVEL

DOUBLE BEVEL*

6"W x 74"L x 5/8"H

SINGLE HOLLYWOOD BEVEL*

4"W x 36"L x 3/4"H

DOUBLE BEVEL*

6"W x 36"L x 3/4"H

DOUBLE BEVEL**

4"W x 36"L x 5/8"H

DOUBLE BEVEL***

2"W x 36"L x 5/8"H

DOUBLE BEVEL**

2"W x 36"L x 3/8"H

DOUBLE HOLLYWOOD BEVEL*

6"W x 36"L x 3/4"H

DOUBLE HOLLYWOOD BEVEL*

4"W x 36"L x 3/4"H

DOUBLE BEVEL*

5"W x 74"L x 5/8"H

* AVAILABLE IN CARRARA WHITE MARBLE M701 ONLY.

** AVAILABLE IN ALL 4 COLORS.

*** AVAILABLE IN CARRARA WHITE MARBLE M701 AND CHIARO BEIGE MARBLE M710 ONLY.158

7834 C.F. Hawn Freeway, Dallas, Texas 75217 | 1.800.933.TILE

To view the complete collection of Daltile® products and information, visit our website at daltile.com. ©2021 Daltile (5/21)

NATURAL STONE

WINDOWSILLS & THRESHOLD

SIZES – WINDOWSILLS�

Thickness Sq. Ft./ Carton

Pieces/ Carton

6" x 74" 6" x 74" x 5/8" (15.24 cm x 187.96 cm x 1.60 cm) 5/8" 77.00 25

5" x 74" 5" x 74" x 5/8" (12.7 cm x 187.96 cm x 1.60 cm) 5/8" 64.25 25

SIZES – THRESHOLDS�

Thickness Sq. Ft./ Carton

Pieces/ Carton

6" x 36" 6" x 36" x 3/4" (10.16 cm x 91.44 cm x 2.00 cm) 3/4" 37.50 25

4" x 36" 4" x 36" x 3/4" (10.16 cm x 91.44 cm x 2.00 cm) 3/4" 25 25

4" x 36" 4" x 36" x 5/8" (10.16 cm x 91.44 cm x 1.60 cm) 5/8" 25 25

2" x 36" 2" x 36" x 5/8" (5.08 cm x 91.44 cm x 1.60 cm) 5/8" 12.50 25

2" x 36" 2" x 36" x 3/8" (5.08 cm x 91.44 cm x 1.00 cm) 3/8" 12.50 25

� Refer to the front of this sales sheet for color availability.

INSTALLATION

Grout Joint Recommendation

As needed depending on type of installation.

PERFORMANCE CHARACTERISTICS

ASTM# Absolute Black G771

Carrara White M701

Chiaro Beige M710 (metric)

Thassos White M420 (metric)

Absorption by Weight % C97 0.33% 0.10% 0.09% 0.15%

Density, lbs/ft3, (kg/m3) C97 160.00 169.41 2.44g/cm3 2,847

Compressive Strength PSI C170 19,000 10,930 N/A 118.00

Abrasion Resistance C241 25.00 14.24 41.00 3.29

Flexural Strength PSI C880 1,200 2,799 30.20 16.00

CONDITIONS OF PURCHASE

Natural stone products inherently lack uniformity and are subject to variation in aesthetics (color, shade, finish, etc.) and performance (hardness, strength, slip resistance, etc.). Natural stone products do not meet minimum coefficient of friction thresholds recommended by safety standard setting organizations. No warranties, express or implied, relative to merchantability or fitness for a particular purpose are made regarding the natural stone products distributed by Dal-Tile. Check local building codes prior to specification or installation to verify that product technical characteristics comply with required parameters.

For additional information refer to “Factors to Consider” at: www.daltile.com/CommercialFactors

Water, oil, grease etc. create slippery conditions. Floor applications with exposure to these conditions require extra caution in product selection.

Not for use on ramps.

Note: Polished surfaces are not recommended for floor areas where slip resistance is a concern.

TECHNICAL INFORMATION

Shade Variation Soundness Special Notes

Absolute Black G771 Low A l

Carrara White M701 Medium A ♦ t l Q

Chiaro Beige M710 Low A ♦ t l

Thassos White M420 Low A ♦ t l Q

Shade Variations and Aesthetic Classification

Low: Background color is relatively uniform.

Medium: Background color contains slight variation.

High: Background color contains distinct variation.

Random: Variegated in color and veining. Blending allowances during installation are strongly recommended.

Soundness:

Group A: Sound Stones with no geological voids or fissures. These stones do not require any filling or patching.

Group B: Similar to Group A, but geological imperfections could be evident. These stones may contain holes or voids, which are filled with epoxy or resin.

Group C: These stones may contain holes, voids, lines of separation and structural flaws. It is standard practice to repair these stones by filling them or reinforcing them.

Group D: Similar to Group C but these stones contain larger natural faults and require more refinishing over time.

Special Notes:

n Not recommended for wet areas.

♦ Can be used in interior wet areas, if sealed and maintained properly. If not properly maintained, the stone look could be altered. Please contact your sealer manufacturer or your Daltile sales representative for information about products that can protect the stone from moisture exposure t Might contain dry seams, pits, fossils and glass veins that are filled at the factory or during installation. These are all inherent characteristics of the stone. Since these voids can sometimes lose their fillings, they should be refilled as part of normal maintenance.

l A sealer is recommended. (Note: Some limestone and tumbled stone should be sealed prior to grouting.).

Q White thin-set or mortar is recommended.

CT101

Product CT101 Color 103976 Steel Collection Common Theme Backing GlasBac

Product Specifications Product Number 1462502500

Product Construction Tufted Textured Loop

Yarn System Post-Consumer Content Nylon

Yarn Manufacturer Universal

Dye Method 100% Solution Dyed

Soil/Stain Protection Protekt²®

Preservative Protection Intersept

Imperial Metric Tufted Yarn Weight 17 oz/yd²,17 oz/yd²,22 oz/yd² 576 g/m²,746 g/m²

Machine Gauge 1/12 in 47.2 ends/10cm

Pile Height 0.16 in 4.1 mm

Pile Thickness 0.104 in 2.6 mm

Stitches 8 /in 31.5 ends/10cm

Pile Density 5,885 oz/yd³ 218,214 g/m³

Size 19.69 in x 19.69 in 50cm x 50cm

Performance Specifications Flooring Radiant Panel (ASTM E-648) Passes

Smoke Density (ASTM E 662) ≤ 450

Flammability Passes Methenamine Pill Test (DOC-FF1-70)

Lightfastness (AATCC 16 - E) ≥ 4.0 @ 60 AFU's

Static (AATCC - 134) < 3.0 KV

Dimensional Stability AACHEN Din 54318 <.10%

Traffic Classification Heavy

Fiber Modification Ratio 1.7 to 1.9

Preservative Efficacy (AATCC 174 Parts 2&3) 99% Reduction/No Mold 7 Days (ASTM E-2471) Complete Inhibition

Health + Environmental Specifications Carbon Footprint

Embodied Carbon (Cradle to Gate)

4.78 (based upon 20 oz face weight) Kg CO /M | (see in

EC3)

Full Life Cycle Carbon Emissions Certified Carbon Neutral Floors™

Total Recycled Content 64%

Recycled Content (Pre Consumer) 63%

Recycled Content (Post Consumer) 1%

Indoor Air Quality Green Label Plus #GLP0820

CDPH 01350

Material Composition Free of Added Heavy Metals, Ortho Phthalates, Formaldehyde, Fluorinated Chemicals (PFAS), and Halogenated Flame Retardants.

Disclosure of Environmental Impacts Environmental Product Declaration

Disclosure of Product Ingredients Health Product Declaration

Environmental Certifications NSF/ANSI 140 Gold

LEED v4 Contributes to multiple IEQ and MR credits

End of Life Carpet to Carpet Recycling through ReEntry®

Technical Information Installation Interface Installation Guidelines

Maintenance Recommended Interface Maintenance Guidelines

Reclamation Recyclable through ReEntry - Call 1.888.733.6873 (U.S.) /

1.866.398.3191 (Canada)

Warranty 15 Year Standard Carpet Warranty

Non Directional

Installation Method

All product specifications reflect averages derived from product sample testing, are subject to normal manufacturing and testing tolerances and inherent pattern variances, and may be changed without notice. For more information about these and other important attributes of the product(s) described herein, including recycled content and product warranty information, please see www.interface.com/disclaimer.

Page 1 of 2 November 6, 2021 https://www.interface.com/disclaimer https://interfaceinc.scene7.com/is/image/InterfaceInc/https://interfaceinc.scene7.com/is/content/InterfaceInc/Sandbox/Gayle/wc_am-carpetwarranty-ams-42021.pdf https://interfaceinc.scene7.com/is/content/InterfaceInc/Interface/Americas/WebsiteContentAssets/Documents/Technical/Maintenance/Carpet/Americas/wc_am-carpetmaintenance-73119-sp-fr-en.pdf https://interfaceinc.scene7.com/is/content/InterfaceInc/Sandbox/Gayle/wc_am-glasbaccquestgbgraphinstallation-42021.pdf https://interfaceinc.scene7.com/is/content/InterfaceInc/Interface/Americas/WebsiteContentAssets/Documents/Certificates/NSF140/NSF140GlasBac/wc_am-nsf140glasbacgold.pdf https://interfaceinc.scene7.com/is/content/InterfaceInc/Interface/Americas/WebsiteContentAssets/Documents/Technical/HPD/HPD-GlasBac/wc_am-hpdglasbac.pdf https://interfaceinc.scene7.com/is/content/InterfaceInc/Interface/Americas/WebsiteContentAssets/Documents/Technical/EPDBriefs/GlasBacNylon6/wc-am-glasbac-epd.pdf https://interfaceinc.scene7.com/is/content/InterfaceInc/Interface/Americas/WebsiteContentAssets/Documents/Certificates/GLP0820-2020/wc_am-glp0820.pdf https://buildingtransparency.org/ec3/epds/5f051fd157794e129afcd10d1974cb6e https://interfaceinc.scene7.com/is/content/InterfaceInc/Interface/Americas/WebsiteContentAssets/Documents/Briefs/wc_am-protek2brief.pdf

Installation Method Non Directional

Standard Backing GlasBac

Backing Options (Learn more) CQuest™Bio, CQuest™GB, GlasBac , ReadyBac™, GlasBac RE, CushionBac Plus

Tile Size Options 50cm x 50cm

Manufacturing Location ISO 9001 & 14001 Certified facilities in Troup County, Georgia, United States

Page 2 of 2 November 6, 2021 https://interfaceinc.scene7.com/is/content/InterfaceInc/Interface/Americas/WebsiteContentAssets/Documents/Certificates/ISO%209001-14001/wc_am-iso9001-14001-certificate.pdf https://www.interface.com/US/en-US/technical/performance/backings-en_US

FLOOR

FABRIC ART™

COLORBODY™ PORCELAIN with REVEAL IMAGING®

Cover photo features Fabric Art™ Modern Linear Dark Gray 12 x 24 and Modern Kaleidoscope Natural Prism 12 x 24 on the floor.

Above photo features Fabric Art™ Modern Textile Medium Gray 24 x 24 and Modern Kaleidoscope Ashen Steel Prism 12 x 24 on the floor and Modern Linear Midnight Blue 12 x 24 on the wall.

Dramatic Texture Brought To Life

• ABSTRACT ART VISUAL

- Features an unpolished finish and gradient, textural variation

- Available in a modern, neutral palette

• STRIKING VERSATILITY

- Offered in six colors and four decorative accent blends that can be used to create one-of-a-kind designs

- Available in two floor tile sizes and a 1 x 3 straight-joint mosaic

- Offers endless possibilities for mixing textures and colors to achieve a personalized look

Inspired by the drape of luxurious textiles, Fabric Art™ uses the weaving mill as a muse, delivering porcelain tile that begs to be touched. Woven, linear and kaleidoscope patterns create a subtle reaction to light and deliver ultimate style for today’s modern spaces, bringing your vision to life. Each texture can stand alone as a centerpiece, or serve as a well-orchestrated pairing.

PRE-CONSUMER

RECYCLED MATERIALS

MADE IN THE U.S.A.

REVEAL IMAGING®

TRU-EDGE™

All or select items within this series meet the requirements for these qualifications.

For more information visit daltile.com.

USAGE

Floors Walls Countertops

F W C 163

FLOOR

FABRIC ART™

COLORBODY™ PORCELAIN with REVEAL IMAGING®

MODERN TEXTILE WHITE MT50

MODERN TEXTILE

WHITE MT50

MODERN LINEAR WHITE ML60

MODERN KALEIDOSCOPE NATURAL PRISM MK70

Beige/Taupe

MODERN KALEIDOSCOPE WHITE ASH PRISM MK71

White/Medium Gray/Dark Gray

MODERN KALEIDOSCOPE ASHEN STEEL PRISM MK72

Medium Gray/Dark Gray

MODERN KALEIDOSCOPE MIDNIGHT STEEL PRISM MK73

Dark Gray/Midnight Blue

MODERN TEXTILE BEIGE MT51

MODERN TEXTILE

BEIGE MT51

MODERN TEXTILE TAUPE MT52

MODERN TEXTILE

TAUPE MT52

MODERN TEXTILE MEDIUM GRAY MT53

MODERN TEXTILE

MEDIUM GRAY MT53

MODERN TEXTILE DARK GRAY MT54

MODERN TEXTILE

DARK GRAY MT54

MODERN TEXTILE MIDNIGHT BLUE MT55

MODERN TEXTILE

MIDNIGHT BLUE MT55

MODERN LINEAR BEIGE ML61

MODERN LINEAR TAUPE ML62

MODERN LINEAR MEDIUM GRAY ML63

MODERN LINEAR DARK GRAY ML64

MODERN LINEAR MIDNIGHT BLUE ML65

FLOOR TILE –

MODERN TEXTILE/MODERN LINEAR

FLOOR TILE –

MODERN KALEIDOSCOPE

1 x 3 STRAIGHT JOINT MOSAIC (Available in Modern Textile only)

SIZES

Thickness Sq. Ft./ Carton

Pieces/ Carton

24 x 24 Floor Tile n

(23-7/16" x 23-7/16") (59.44 cm x 59.44 cm) 3/8" 15.20 4

12 x 24 Floor Tile

(11-11/16" x 23-7/16") (29.56 cm x 59.44 cm) 3/8" 15.12 8

1 x 3 Straight-joint Mosaic n

(Mesh-mounted)

(11-5/8" x 11-13/16" Sheet) (29.61 cm x 29.99 cm Sheet) 3/8" 9.56 10 n Available in Modern Textile only

INSTALLATION

Grout Joint Recommendation Shade Variation

1/8" (3/16" when multiple sizes are installed in a modular pattern, and/or when installing tile with a length 15” or greater in a staggered brick-joint pattern;

overlap should not exceed 33%.)

Medium (V2)

NOTES

Since there are variations in all fired ceramic and natural products, tile and trim supplied for your particular installation may not match samples. Final confirmation should be made from actual tiles and trim prior to installation. Manufactured in accordance with ANSI A137.1 standards.

Not for use on ramps. Water, oil, grease, improper drainage and certain footwear can create slippery conditions. Floor applications expected to be exposed to these conditions require extra caution in product selection.

For additional information refer to “Factors to Consider” at:

daltile.com/Factors.

Special consideration needs to be given when installing tiles greater than 15 inches. Please refer to daltile.com/LargeTiles for more information.

Special care should be taken when grouting with dark pigmented colors. A grout release is recommended to prevent finely powdered pigments from lodging in the pores of the surface. Use of a latex modified thin-set is recommended for installation.

TRIM

Type Number Size Pieces/ Carton

Bullnose n P-43C9 3 x 12 30

Cove Base n P-36C9T 6 x 12 22

Cove Base Outcorner n

PC-36C9T 1 x 6 15

Bullnose in Modern Linear and Modern Kaleidoscope available through Special Order with extended lead time.

Cove base trim is intended to coordinate with floor tile in the standard 90-degree installation position.

Cove base and cove corner trim are suitable for non-freezing climates only.

n Available in Modern Textile only

FLOOR

FABRIC ART™

COLORBODY™ PORCELAIN with REVEAL IMAGING®

7834 C. F. Hawn Freeway, Dallas, Texas 75217 | 1.800.933.TILE

To view the complete collection of Daltile® products and information, visit our website at daltile.com.

DESIGNED TO HELP EARN LEED™

CREDITS. For more detailed information, visit daltilegreenworks.com. ©2018 Daltile (3/18)

APPLICATIONS

Target DCOF wet Suitable

Dry & Level – Interior Floor N/A

Wet & Level – Interior Floor ≥ 0.42

Shower Floors (Residential or Light Commercial) ≥ 0.42 *

Exterior Floor Applications (including pool decking & other wet areas with minimal footwear)

≥ 0.60

Ramps & Inclines ≥ 0.65

Walls/Backsplashes N/A

Countertops N/A

Pool Linings N/A *

A DCOF value of ≥ 0.42 is the standard for tiles specified for level interior spaces expected to be walked upon when wet, as stated in ANSI A137.1-2012, Section 9.6.

For more information about DCOF and the DCOF AcuTest™, visit daltile.com/DCOF.

APPLICATION NOTES:

Suitable for exterior applications in freezing and non-freezing climates, when proper installation methods are followed.

* Mosaic tile only

PERFORMANCE CHARACTERISTICS

ASTM# Result

Water Absorption C373 < 0.5%

Breaking Strength C648 > 275 lbs

Scratch Hardness MOHS 8.0

Chemical Resistance C650 Resistant

Abrasion Resistance C1027 N/A

For additional information on test results, visit us at:

daltile.com/information/TestResults.

Premium Interior Paints

SPARTAWALL®

Superior hide and durability.

IN

TER

IO

R

Metal Masonry WoodDrywall

FLAT VELVET EGGSHELL LOW SHEEN SEMI-GLOSS

Family Room • • •

Living Room • • •

Dining Room • • • •

Bedroom • • •

Kids’ Room • • •

Kitchen & Bath • •

Hallways • • • •

Ceiling • • •

Office • • •

Doors, Windows & Shutters • •

Moldings •

VOC AND RAVOC RATINGS

ON EVERY LABEL

Dunn-Edwards is the first paint company to label its products with RAVOC ratings — Reactivity-Adjusted VOC Content — a better way to measure potential air quality impacts of coatings. To learn more about RAVOC ratings visit dunnedwards.com/RAVOC.

LEED® GOLD-CERTIFIED PAINT

MANUFACTURING FACILITY

In 2011, Dunn-Edwards opened the world’s first and only LEED® Gold-certified paint manufacturing facility in Phoenix, AZ. Encompassing manufacturing, product development, quality control and more, the 336,000-sq. ft.

facility is designed to be the greenest in the industry.

“LEED”and related logo is a trademark owned by the U.S. Green Building Council and is used with permission.

PRODUCTS BEARING THIS LOGO ARE

EG-FREE® AND TAC/HAP-FREE

Ethylene Glycol (EG), a solvent often used in water-based paints, is listed as a Toxic Air Contaminant (TAC) and Hazardous Air Pollutant (HAP). In 1983, we were the first in the industry to voluntarily replace EG with Propylene Glycol, a non-toxic alternative “generally regarded as safe” by the FDA. Also, every Dunn-Edwards product with the EG-Free logo is formulated without any other TAC or HAP, too.

is a complete line of premium, ultra-low VOC, interior acrylic paints. It is formulated to provide a tough, durable, block resistant finish that is easy to apply. SPARTAWALL is ideally suited for use on commercial and residential projects, such as schools, hotels, hospitals, and single family or multi-tenant housing.

SPARTAWALL®

:: Formulated using high quality resins and pigments that withstand repeated washing

:: Superior block resistance

:: Easy…