A05_Sign_Panel_Install_Guide.pdf
PDF 712 KB Posted
- Attached to
- BLM-CO WRFO KIOSK SIGN PANELS
- Solicitation number
- 140L1726Q0009
About this file
This document is an installation guide for Rockart Message Center Kiosk sign panels. The guide provides detailed technical instructions for two primary installation scenarios: fully-enclosed sign panels and single/double-sided sign panels with mounting holes in each corner.
For fully-enclosed sign panels, the document specifies that installers must verify the removable side rail position (containing 3-5 bolts) is located on the right side and vertically aligned before mounting. If routed text is included on headers and footers, proper orientation for front-facing readability is required. The guide includes step-by-step procedures for installing tamper-resistant VandlGard nuts, which involve threading the cone-shaped nut onto the bolt, hand tightening, and then using a wrench to shear off the hex portion while leaving the conical part in place. For accessing and opening fully-enclosed panels to change content, the guide instructs users to remove bolts using a yellow hex tool (included), extract the flexible security rod from the grooved channel, slide and lift the clear polycarbonate cover, and ensure proper reinstallation with the security rod before reattaching the access rail.
For standard sign panels with four corner mounting holes, the guide provides three assembly kit options (03-901 for tackboard only, 03-903 for single-sided header/footer, and 03-904 for double-sided header/footer) with specific hardware stacking sequences. Each configuration requires carriage bolts, black nylon carriage bolt adapters, plastic flat washers, 2-inch stainless steel fender washers, slotted sign panel mounting tabs, and VandlGard break-away nuts. All hardware components must be assembled in the specified order at each corner to securely attach the sign panel to the kiosk's vertical steel posts.
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Ro ck ar t, In c.
v .2
Se p0
3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com
Message Center Kiosk Stage II - Sign Panel Installation
Installation note for “fully-enclosed” Sign Panels:
Before mounting a Fully-Enclosed* Sign Panel to the Kiosk, check the position of the removable side rail. The 3 to 5 bolts embedded within this rail (circled on left) are used to secure the entire display and when installed, should be located on the right side, vertically aligned.
If the sign panel was ordered with the optional routed text on the header and/or footer, ensure the text is oriented correctly and is readable when viewing the front side of the kiosk.
How to properly install a VandlGard® tamper-resistant nut:
If your kiosk sign panel included tamper-resistant mounting hardware, the strange looking nuts are tamper resistant and should be installed as follows:
Start by threading the wide, tapered end of the cone-shaped nut onto the end of the bolt as shown by the green arrow (top image, left). Hand tighten, until snug.
Using a handheld wrench or pliers, continue tightening the Hex part of the nut until the hex part shears off... leaving the conical part in place (bottom image, left). Discard the hex nut. ...Done!
*Fully-Enclosed models protect the displayed content on all sides. These models typically include at a removable side rail on either the left or right side, and a clear polycarbonate cover that is also removable.
Opening a “fully-enclosed“ Sign Panel:
To open up a fully-enclosed* Sign Panel to change the content inside use the special YELLOW colored hex tool (included in the hardware kit) to perform the following steps:
After the 3 to 5 bolts along the right side have been removed (keep in a safe place), Remove the side access rail. Grab the tail-end of the flexible security rod sitting in the narrow grooved channel just above the clear cover, and pull it completely out through the opening (see image, left).
Then slide the clear polycarbonate cover over just enough to allow you to grasp it firmly by the left & right sides. Lift it straight up, inserting the top edge deeper into the top channel. Now, swing the bottom edge of the cover out and away from the front of the kiosk (towards your body). Take note which side was facing out (and when done, return it accordingly).
Place the clear cover in an area that is clean as possible while changing content.
After changes to the content are done: Simply reinstall the clear polycarbonate cover; Don’t forget to RE-INSERT the flexible security rod ! Finally, using the special YELLOW hex tool (included), Re-attach the side access rail using the bolts removed earlier.
Flexible Security Rod
Special Hex tool used to open fully-enclosed sign panels (included)
Stage II - Sign Panel Installation
Important installation details for ROCKART Kiosk Sign Panels and Message Center family of Kiosks
Ro ck ar t, In c.
v .2
Se p0
3006 N. Maple | Mesa, AZ 85215 | P:(480) 854-3400 F:(480) 832-6390 | www.rockartsigns.com | sales@rockartsigns.com
Message Center Kiosk Sign Panel Install Guide
Vertical Steel Post
Tackboard Sign
Slotted Sign Panel Mounting Tab
Plastic Flat Washer
VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex
2“ Dia. Stainless Steel Fender Washer
2“ Dia. Stainless Steel Fender Washer
Carriage Bolt
Black Nylon Carriage Bolt Adapter
FRONT of Kiosk
Clear Polycarbonate Cover (Optional) Vertical Steel Post
Slotted Sign Panel Mounting Tab
Plastic Flat Washer
VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex
2“ Dia. Stainless Steel Fender Washer
2“ Dia. Stainless Steel Fender Washer
Carriage Bolt
Black Nylon Carriage Bolt Adapter FRONT of Kiosk
Tackboard Sign
Header / Footer
Vertical Steel Post
Ballistic Tack Board Sign
Header / Footer
Header / Footer
Slotted Sign Panel Mounting Tab
Plastic Flat Washer
VandlGard break-away nut. Tighten until hex part breaks off from conical part. Discard hex
2“ Dia. Stainless Steel Fender Washer
2“ Dia. Stainless Steel Fender Washer
Carriage Bolt
Black Nylon Carriage Bolt Adapter FRONT of Kiosk
Tack Board Only #03-901 ASSEMBLY KIT
Header / Footer (Single-Sided) #03-903 ASSEMBLY KIT
Header / Footer (Double-Sided) #03-904 ASSEMBLY KIT
Use the included hardware kit from 03-901, follow the hardware stacking order (shown on right) to secure each corner of the sign panel to the kiosk.
Use the included hardware kit from 03-903, follow the hardware stacking order (shown on right) to secure each corner of the sign panel to the kiosk.
Use the included hardware kit from 03-904, follow the hardware stacking order (shown on right) to secure each corner of the sign panel to the kiosk.
Sign Panel Install Guide
For Single- and Double-sided Sign Panels having 1 mounting hole in each corner
File details come from the government source that posted it. Updated .