SECTION 22 30 00 Plumbing Equipment (Boiler Spec).pdf

REPLACE BOILERS IN BUILDING 210

FLETC, GLYNCO GA

AUGUST 9, 2022 PLUMBING EQUIPMENT 22 30 00 - 1

SECTION 22 30 00 - PLUMBING EQUIPMENT

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Domestic hot water storage tanks.

1.02 RELATED REQUIREMENTS

A. Electrical characteristics and wiring connections.

B. Requirements for water storage tanks specified by this section.

C. Product requirements for water storage tanks for placement by this Section.

1.03 REFERENCE STANDARDS

A. ABMA STD 9 - Load Ratings and Fatigue Life for Ball Bearings 2015.

B. ABMA STD 11 - Load Ratings and Fatigue Life for Roller Bearings 2014.

C. ASME BPVC-VIII-1 - Boiler and Pressure Vessel Code, Section VIII, Division 1 - Rules for Construction of Pressure Vessels 2017.

D. ICC (IPC) - International Plumbing Code Most Recent Edition Adopted by Authority Having Jurisdiction, Including All Applicable Amendments and Supplements.

E. NFPA 70 - National Electrical Code Most Recent Edition Adopted by Authority Having Jurisdiction, Including All Applicable Amendments and Supplements.

1.04 SUBMITTALS

A. Product Data:

1. Provide electrical characteristics and connection requirements.

B. Shop Drawings:

1. Indicate dimensions of tanks, tank lining methods, anchors, attachments, lifting points, tappings, and drains.

C. Project Record Documents: Record actual locations of components.

D. Operation and Maintenance Data: Include operation, maintenance, and inspection data, replacement part numbers and availability, and service depot location and telephone number.

E. Warranty Documentation: Submit manufacturer warranty and ensure that forms have been completed in Owner's name and registered with manufacturer.

Replace Boiler B210 FLETC, Glynco GA

22 30 00 - 2 PLUMBING EQUIPMENT FEBRUARY 1, 2022

F. Project Record Documents: Record actual locations of components.

1.05 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing the type of products specified in this section, with minimum three years of documented experience.

B. Certifications:.

1. Water Tanks: ASME labeled to ASME BPVC-VIII-1.

1.06 DELIVERY, STORAGE, AND HANDLING

A. Provide temporary inlet and outlet caps. Maintain caps in place until installation.

1.07 WARRANTY

A. Provide manufacturer warranty for domestic water heater storage tanks.

PART 2 PRODUCTS

2.01 DOMESTIC HOT WATER STORAGE TANKS

A. Manufacturers:

1. Cemline (or approved substitute)

B. Tank: 450 gallon Glass-Lined, Jacketed & Insulated ASME Tanks, Lock-Temp Design Locks Hot Water at Top, Cold Water at Bottom.

C. Openings: Up to 3 inches (75 mm), copper-silicone threaded; over 4 inches (100 mm), flanged; flanged collar for heat exchanger; manway fitting.

D. Accessories: Provide the following: tank drain, water inlet and outlet, thermometer with range of 40 to 200 degrees F (4 to 93 degrees C), ASME pressure relief valve suitable for maximum working pressure.

2.02 ELECTRICAL WORK

A. Supply manual or automatic control and protective or signal devices required for the operation specified, and any control wiring required for controls and devices not shown.

PART 3 EXECUTION

3.01 INSTALLATION

A. Install plumbing equipment in accordance with manufacturer's instructions, as required by code, and complying with conditions of certification, if any.

REPLACE BOILERS IN BUILDING 210

FLETC, GLYNCO GA

AUGUST 9, 2022 PLUMBING EQUIPMENT 22 30 00 - 3

B. Coordinate with plumbing piping and related fuel piping work to achieve operating system.

C. Domestic Water Storage Tanks:

1. Provide steel pipe support, independent of building structural framing members.

2. Clean and flush prior to delivery to site. Seal until pipe connections are made.

3. Provide piping insulation on all hot water piping between new storage tanks.

END OF SECTION 22 30 00