7-JSD - Elk Ridge Middle - Auditorium - Elect CD Set - 2026-03-30.pdf

PDF 833 KB Posted Mar 31, 2026

Attached to: IFB - Theatrical Lighting Upgrade for Elk Ridge Middle School
Solicitation number: 26DB28
Issued by: Utah

About this file

Written by GovTribe AI · Apr 3, 2026

This is a construction document set for a theatrical lighting and audio visual upgrade project at Elk Ridge Middle School, located at 3659 West 9800 South, South Jordan, Utah 84009, issued by Jordan School District. The project, identified as JSD Bid Number 26DB28, involves the installation of new theatrical lighting fixtures, dimming control systems, audio visual equipment, and related electrical infrastructure in the school's auditorium and projection room. The scope of work includes demolition of existing theatrical lighting fixtures and equipment, installation of LED theatrical lighting fixtures (including Color Source Spot V, Color Source Par V, and Color Source Cyc fixtures), replacement of dimming rack modules from 96 existing D20 modules to 48 new R20 dual relay modules, installation of new control consoles and touch screens, new recessed down lights, and comprehensive audio visual system upgrades. The construction documents, issued April 1, 2026, by Envision Engineering (Project No. 2025-247.01, Contact: Scott Kingery, 801-534-1130) include detailed electrical and AV plans, fixture schedules, riser diagrams, demolition plans, and specifications for all work required to complete the theatrical and AV system upgrades.

The electrical contractor is responsible for providing all labor, materials, and equipment necessary for a complete and operational system in compliance with the specifications and all applicable codes. Critical requirements include the use of insulated throat connectors or plastic bushings for all conduit sizes, dedicated neutral conductors for all lighting and power circuits, proper labeling of all electrical equipment, seismic support and bracing for equipment, and wire sizing that ensures adequate capacity for voltage drop calculations. The contractor must conduct a pre-construction site visit to examine all existing physical conditions, verify existing branch circuits and dimming assignments, and coordinate all work with the theatrical lighting system supplier and installer prior to rough-in and construction. An ETC-certified technician must be engaged for dimming rack module replacement and reconfiguration. All existing fire alarm systems must remain operational during construction, and all configuration files and documentation must be delivered to the owner prior to project closeout. Costs for project closeout documentation, protective measures for existing equipment, and any damage to existing systems during construction are the responsibility of the contractor at no additional cost to the owner.

View the file

Other files

File	Type	Posted
4-Attachment E - Student Data Privacy Agreement - 07.pdf	PDF	Mar 31, 2026
5-Attachment F - URS Post-Retired Verification Form.pdf	PDF	Mar 31, 2026
3-Attachment A - JSD Standard Terms Conditions.pdf	PDF	Mar 31, 2026
6-26DB28 - IFB - Theatrical Lighting Upgrade Elk Ridge Middle School.docx	DOCX document	Mar 31, 2026
8-JSD - Elk Ridge Middle School - Auditorium - Project Manual - 2026-04-01.pdf	PDF	Mar 31, 2026
2-Attachment B - Boycott Statement - 09.pdf	PDF	Mar 31, 2026
1-Vendor Information Sheet - 02.26.2025.pdf	PDF	Mar 31, 2026

On GovTribe

Work with this file

Download the original file
Contacts named in this file
Similar government files
Ask GovTribe AI about this file

Try for free Login

Text version

The file's text, extracted by GovTribe without its formatting.

EG001

COVER SHEET

Vicinity Map

Site

NORTH

ENVISION ENGINEERING

240 EAST MORRIS AVENUE STE. 200

SALT LAKE CITY, UT 84115

P: (801) 534-1130

SKINGERY@ENVISIONENG.COM

CONTACT: SCOTT KINGERY

JSD BID NUMBER: 26DB28 ISSUE TYPE: REVIEW SET ISSUE DATE: APRIL 01, 2026

DRAWING INDEX

EG001 COVER SHEET

EG101 SYMBOLS AND NOTES

EG102 OVERALL BUILDING PLAN

ED101 LIGHTING DEMOLITION PLANS

EL101 LIGHTING PLANS

EL501 LIGHTING RISER DIAGRAM AND FIXTURE

SCHEDULE

EA101 AUDIO VISUAL PLANS

EA501 AUDIO VISUAL SCHEDULES, NOTES, DETAILS

AND DIAGRAMS

NO. DATE REVISIONS

1 2 3 4 5

CHECKED BY: DW

DRAWN BY: SP / SK

ENVISION PROJECT NO: 2025-247.01

DATE:

ISSUE:

04/01/2026

CONSTRUCTION DOCUMENTS

6 7

240 E. MORRIS AVE. SUITE 200

SALT LAKE CITY, UT 84115

P (801) 534-1130 F (801) 534-1080 www.envisioneng.com

Fil e N am e:

\25

\20

-2

.00

- A ud ito riu m Up gr ad es \01

_D wg s\E lk

Ri dg e M idd le\

1.d wg La st Pl ott ed

: 2

6/0 3/3

0 @ 6:

:01

P M

By : S

L D

L L

, U T

JORDAN SCHOOL DISTRICT

ELK RIDGE MIDDLE SCHOOL

AUDITORIUM THEATRICAL LIGHTING

AND AUDIO VISUAL UPGRADE

3659 WEST 9800 SOUTH

SOUTH JORDAN, UT 84009

http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com

EG101

SYMBOLS AND

NOTES

ELECTRICAL SYMBOL SCHEDULE GENERAL NOTES

MOUNT ALL OUTLETS, DEVICES, AND EQUIPMENT AT HEIGHTS INDICATED BELOW, UNLESS NOTED OTHERWISE ON THE DRAWINGS. UNLESS NOTED OTHERWISE, HEIGHTS ARE GIVEN FROM FINISHED

FLOOR TO CENTER OF OUTLET BOX.

WHERE OUTLETS, DEVICES, AND EQUIPMENT ARE NOTED BY SUBSCRIPTS, REFER TO ABBREVIATION

SCHEDULE FOR DEFINED REQUIREMENTS.

WHERE OUTLETS, DEVICES AND EQUIPMENT ARE NOTED BY THE SUBSCRIPT 'A', MOUNT AT 4" ABOVE

COUNTER. IF COUNTER HAS A BACK SPLASH, MOUNT AT 4" ABOVE BACK SPLASH. REFER TO

ARCHITECTURAL INTERIOR ELEVATIONS AND COORDINATE WITH CASEWORK SUPPLIER.

NOT ALL ELECTRICAL SYMBOLS MAY BE USED.

NOTE: NOT ALL ABBREVIATIONS MAY BE USED.

ABBREVIATION SCHEDULE

ABOVE COUNTER

AMP OR AMPS

ADJACENT

ABOVE FINISHED FLOOR

AUTHORITY HAVING JURISDICTION

ALUMINUM

CONDUIT

CIRCUIT BREAKER

CIRCUIT

CONVENIENCE OUTLETS

COPPER

EACH

ELECTRICAL

EMERGENCY

ELECTRIC METALLIC TUBING

ELECTRIC NONMETALLIC TUBING

EQUIPMENT

ELECTRIC WATER COOLER

EXISTING

EXPLOSION PROOF

FIRE ALARM

FIRE ALARM CONTROL PANEL

FULL LOAD AMPS

FLEXIBLE METAL CONDUIT

FREIGHT ON BOARD

GROUND CONDUCTOR

HAND-OFF-AUTO

HORSE POWER

ISOLATED GROUND

INTERMEDIATE METAL CONDUIT

INSULATED

A A

ADJ

AFF

AHJ

CKT

C.O.'S

ELEC

EMT

ENT

EQUIP

EWC

E, EX

EXP

FACP

FLA

FMC

FOB

GND

HOA

IMC

INS

ISOLATED

KILO VOLT AMPERES

KILOWATTS

LIQUID-TIGHT METAL CONDUIT

LIQUID-TIGHT NONMETAL CONDUIT

MINIMUM CIRCUIT AMPS

MAIN LUGS ONLY

NORMALLY CLOSED

NOT IN CONTRACT

NIGHT LIGHT

NORMALLY OPEN

ON CENTER(S)

OVER CURRENT PROTECTION

QUANTITY

REMOVE

REQUIREMENTS

RIGID METAL CONDUIT

RIGID NONMETALLIC CONDUIT

REMOVE AND RELOCATE

SURGE SUPPRESSION

SECURITY CONTROL PANEL

TAMPER RESISTANT

TYPICAL

TRANSIENT VOLTAGE SURGE SUPPRESSOR

UNDER FLOOR

UNDERGROUND

UNLESS NOTED OTHERWISE

WITH

WEATHER PROOF

TRANSFORMER

ISO

KVA

LFMC

LFNC

MCA

MLO

N.C.

N.I.C.

N.L.

N.O.

O.C.

OCP

QTY

REQ.

RMC

RNC

SCP

TYP

TVSS

U.N.O.

XFMR

GENERAL PROJECT NOTES:

1. DIVISION 26 CONTRACTOR IS RESPONSIBLE FOR READING AND APPLYING WHAT IS IN THE

SPECIFICATIONS TO THIS PROJECT. ANYTHING THAT IS NOT INCLUDED ON THE PROJECT THAT IS CALLED OUT IN THE SPECIFICATION SHALL BE LISTED ON THE SUBSTANTIAL COMPLETION PUNCHLIST.

THE CONTRACTOR WILL BE REQUIRED TO REMEDY THESE DEFICIENCIES. THERE WILL BE NO

EXCEPTIONS.

2. THE CONTRACTOR MAY SCHEDULE A PRE-CONSTRUCTION MEETING AT THEIR DISCRETION, WITH THE ELECTRICAL ENGINEER AND OWNER TO REVIEW THE DRAWINGS AND SPECIFICATIONS. THE MEETING

SHALL BE A MAXIMUM OF ONE HOUR AND SHALL TAKE PLACE ON SITE.

3. THE FOLLOWING ITEMS ARE SOME OF THE REQUIREMENTS THAT ARE LISTED IN THE SPECIFICATIONS.

THESE ITEMS DO NOT REPRESENT ALL ITEMS AND THE CONTRACTOR IS RESPONSIBLE FOR MEETING

ALL REQUIREMENTS OF THE SPECIFICATIONS:

A. INSULATED THROAT CONNECTORS OR PLASTIC BUSHINGS SHALL BE UTILIZED FOR ALL CONDUIT

SIZES USED ON THIS PROJECT.

B. A DEDICATED NEUTRAL CONDUCTOR WILL BE PROVIDED FOR ALL LIGHTING AND POWER CIRCUITS.

C. THE CONTRACTOR SHALL LABEL ALL ELECTRICAL EQUIPMENT AS IT IS CALLED OUT IN THE

SPECIFICATIONS.

D. THE CONTRACTOR SHALL PROVIDE SEISMIC SUPPORT AND BRACING FOR ALL ELECTRICAL

EQUIPMENT AS REQUIRED BY LOCAL AND NATIONAL CODE.

4. THE CONTRACTOR SHALL INSTALL THE WIRE SIZES AS CALLED OUT ON THE ONE-LINE DIAGRAM, EQUIPMENT SCHEDULES, VOLTAGE DROP TABLES, AND ELECTRICAL SPECIFICATIONS. HOWEVER, THE

CONTRACTOR IS RESPONSIBLE TO ENSURE THE WIRE IS LARGE ENOUGH FOR VOLTAGE DROP.

5. THE CONTRACTOR SHALL VISIT THE SITE BEFORE SUBMITTING THE BID, AND SHALL EXAMINE ALL PHYSICAL CONDITIONS WHICH MAY BE MATERIAL TO THE PERFORMANCE OF HIS WORK. NO EXTRA PAYMENTS WILL BE ALLOWED TO THE CONTRACTOR AS A RESULT OF EXTRA WORK MADE NECESSARY BY THEIR FAILURE TO DO SO. ANY CASE OF DISCREPANCY OR LACK OF CLARITY SHALL BE PROMPTLY

IDENTIFIED TO THE OWNER'S REPRESENTATIVE AND THE ENGINEER FOR CLARIFICATION.

6. THE CONTRACTOR SHALL MAKE SURE THAT ALL EXISTING BRANCH CIRCUITS THAT ARE AFFECTED BY

THIS PROJECT ARE NOT OVERLOADED AS A RESULT OF WORK UNDER THIS CONTRACT. PROVIDE

ADDITIONAL BRANCH CIRCUITS FROM ELECTRICAL PANELS AS NECESSARY TO COMPLY WITH THE BRANCH CIRCUIT LOADING REQUIREMENTS. PROVIDE ALL MATERIAL AND LABOR AS NECESSARY FOR A

COMPLETE AND OPERATING SYSTEM.

7. PROVIDE UPDATED, TYPED PANELBOARD SCHEDULE(S) TO REFLECT ALL THE CHANGES MADE, INCLUDING EXISTING LOADS. THE EXISTING LOADS SHALL BE NAMED THE SAME AS LISTED ON THE

EXISTING PANELBOARD SCHEDULE.

8. THE CONTRACTOR SHALL DETERMINE THE EXACT ROUTING OF ALL CONDUITS IN THE FIELD. THIS PLAN

REPRESENTS A SCHEMATIC REPRESENTATION OF DEVICE AND EQUIPMENT LOCATIONS.

NO. DATE REVISIONS

1 2 3 4 5

CHECKED BY: DW

DRAWN BY: SP / SK

ENVISION PROJECT NO: 2025-247.01

DATE:

ISSUE:

04/01/2026

CONSTRUCTION DOCUMENTS

6 7

240 E. MORRIS AVE. SUITE 200

SALT LAKE CITY, UT 84115

P (801) 534-1130 F (801) 534-1080 www.envisioneng.com

Fil e N am e:

\25

\20

-2

.00

- A ud ito riu m Up gr ad es \01

_D wg s\E lk

Ri dg e M idd le\

1.d wg La st Pl ott ed

: 2

6/0 3/3

0 @ 6:

:04

P M

By : S

L D

L L

, U T

ARROWS: NUMBER OF ARROWS INDICATES NUMBER OF

CIRCUITS REQUIRED.

SHORT CROSS LINES: NUMBER OF SHORT CROSS LINES

INDICATES NUMBER OF PHASE, TRAVELER, AND/OR SWITCHED

CONDUCTORS REQUIRED IF GREATER THAN 1 (ONE).

LONG CROSS LINES: NUMBER OF LONG CROSS LINES

INDICATES NUMBER OF NEUTRAL CONDUCTORS REQUIRED

FOR MULTI-WIRE HOME RUNS.

EQUIPMENT GROUND AND ISOLATED GROUND CONDUCTORS:

EQUIPMENT GROUND AND ISOLATED GROUND CONDUCTORS

ARE NOT SHOWN, BUT ARE REQUIRED AS NOTED ON THE

DRAWINGS OR IN THE SPECIFICATIONS.

DESCRIPTIONSYMBOL REMARKS

1 CIRCUIT, 2 WIRE BRANCH CIRCUIT HOME RUN TO PANEL

2 CIRCUIT, 4 WIRE BRANCH CIRCUIT HOME RUN TO PANEL

3 CIRCUIT, 6 WIRE BRANCH CIRCUIT HOME RUN TO PANEL

MULTIPLE WIRE BRANCH CIRCUITING BETWEEN FIXTURES,

SWITCHES, DEVICES, ETC.

BRANCH CIRCUITING (U.N.O.) TURNED UP OR TOWARDS

OBSERVER.

BRANCH CIRCUITING (U.N.O.) TURNED DOWN OR AWAY FROM

OBSERVER.

BRANCH CIRCUITING (U.N.O.) CONTINUATION

CONDUIT STUB-IN

INCOMING SERVICE

JUNCTION BOX MOUNT AS NOTED. SUBSCRIPT 'F' INDICATES TO PROVIDE A

FLOOR BOX WITH BLANK COVERPLATE

BRANCH CIRCUITING SYMBOLS

CAP AND MARK

E-1

E-2

TOP NUMBER INDICATES DETAIL NUMBER; BOTTOM

LETTER-NUMBER INDICATES WHERE DETAIL IS SHOWN.

E-3

AHU

TOP NUMBER ABBREVIATES EQUIPMENT NAME OR TYPE;

BOTTOM NUMBER INDICATES EQUIPMENT NUMBER. REFER TO

EQUIPMENT SCHEDULE.

USED TO DENOTE CHANGES EITHER ISSUED BY ADDENDUM OR

DURING CONSTRUCTION AND TO DENOTE RECORD DRAWING

CHANGES.

USED TO BREAK DRAWINGS.

DESCRIPTIONSYMBOL REMARKS

GENERAL SYMBOLS

KEYED NOTE

DETAIL REFERENCE

ELEVATION REFERENCE

SECTION REFERENCE

ARCHITECTURAL ROOM NUMBER

EQUIPMENT NAME / NUMBER

REVISION NUMBER

BREAKLINE

TOP NUMBER INDICATES SECTION NUMBER; BOTTOM

LETTER-NUMBER INDICATES WHERE SECTION IS SHOWN.

TOP NUMBER INDICATES ELEVATION NUMBER; BOTTOM

LETTER-NUMBER INDICATES WHERE ELEVATION IS SHOWN.

USED TO DENOTE AREAS, DEVICES, EQUIPMENT DETAILS, ETC.

AFFECTED BY REVISION.

REVISION CLOUD

DESCRIPTIONSYMBOL MOUNTING REMARKS

1. LIGHT FIXTURE SYMBOLS ARE GENERAL IN NATURE AND MAY BE SHOWN ON THE DRAWINGS IN VARIOUS SIZES AND SHAPES. REFER TO

THE LIGHT FIXTURE SCHEDULE FOR SPECIFICATION INFORMATION.

2. ARROWS INDICATE AIMING DIRECTION.

LIGHTING SYMBOLS

ARM-MOUNTED SINGLE-HEAD LIGHT FIXTURE AND POLE

ARM-MOUNTED DOUBLE-HEAD LIGHT FIXTURE AND POLE

POST-TOP SINGLE-HEAD, LIGHT FIXTURE AND POLE

WALL-MOUNTED FIXTURE

LIGHT BOLLARD

FLOOD LIGHT

RECESSED WALL FIXTURE OR STEP LIGHT

LIGHT FIXTURES

WALL-MOUNTED LINEAR LIGHT FIXTURE

LINEAR WALL WASHER

RECESSED DOWN LIGHT

RECESSED WALL-WASHER OR DIRECTIONAL DOWNLIGHT

SURFACE OR PENDANT-MOUNTED LIGHT FIXTURE

WALL-MOUNTED LIGHT FIXTURE

TRACK OR MONO-POINT LIGHT FIXTURE

WALL SCONCE

EGRESS LIGHT FIXTURE

EMERGENCY (NON-EGRESS) LIGHT FIXTURE

CEILING MOUNTED EXIT SIGN

WALL-MOUNTED EXIT SIGN

WALL-MOUNTED EXIT SIGN W/ EMERGENCY LIGHT FIXTURE

TIME CLOCK

EMERGENCY LIGHT FIXTURE

ELECTRIC PHOTOCELL

LIGHT FIXTURE CALLOUT (LETTER DENOTES FIXTURE TYPE)

REFER TO ARCHITECTURAL EXTERIOR

ELEVATIONS FOR MOUNTING HEIGHT

REFER TO ARCHITECTURAL EXTERIOR

ELEVATIONS FOR MOUNTING HEIGHT

IF SHOWN, ARROW INDICATES AIMING

DIRECTION

REFER TO ARCHITECTURAL EXTERIOR

ELEVATIONS FOR MOUNTING HEIGHT

IF SHOWN, ARROW INDICATES AIMING

DIRECTION

CEILING

AS NOTED

N/A

THIS IS AN EXAMPLE OF AN EGRESS LIGHT

FIXTURE. EGRESS LIGHT FIXTURES ARE

HALF-SHADED DIAGONALLY.

THIS IN AN EXAMPLE OF AN EMERGENCY

(NON-EGRESS) LIGHT FIXTURE.

EMERGENCY FIXTURES ARE

FULLY-SHADED.

DARKENED PORTION OF SIGN INDICATES

FACE(S); ARROW(S) INDICATE CHEVRON

DIRECTION(S)

AS SPECIFIED

OR DETAILED

WALL

ABOVE DOOR

MOUNT ON ROOF FACING NORTH SKY

WALL

ABOVE DOOR

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

AS SPECIFIED

OR DETAILED

+60"

WIRING DEVICE SYMBOLS

(5-20R)

J a

DIM

TIM

3PM

3PN

DESCRIPTIONSYMBOL MOUNTING REMARKS

SUBSCRIPT KEYS SWITCH TO FIXTURES

CONTROLLED.

RATE DIMMER SWITCH FOR MAXIMUM

POSSIBLE WATTAGE

DUAL LEVEL SWITCH OUTBOARD LAMPS

SEPARATELY FROM INBOARD LAMPS.

REFER TO DETAIL UP-ON;

CENTER-NEUTRAL; DOWN-OFF

CEILING MOUNTED WITH SUBSCRIPT 'C';

WALL-MOUNTED WITH SUBSCRIPT 'W'

UP-ON; CENTER-OFF; DOWN-ON

RANGE -- NEMA 14-50R

DRYER -- NEMA 14-30R

SUBSCRIPT IN PARENTHESIS INDICATES

NEMA CONFIGURATION IF SHOWN. REFER

TO DRAWINGS AND/OR EQUIPMENT

SCHEDULES. CONFIRM EXACT

CONFIGURATION WITH OWNER PRIOR TO

INSTALLATION.

REFER TO DETAIL

4" ABOVE

BACKSPLASH

SINGLE-POLE TOGGLE SWITCH

DOUBLE-POLE TOGGLE SWITCH

THREE-WAY TOGGLE SWITCH

FOUR-WAY TOGGLE SWITCH

KEY-OPERATED SINGLE-POLE TOGGLE SWITCH

SINGLE-POLE TOGGLE SWITCH WITH PILOT LIGHT

DIMMER SWITCH

TIMER SWITCH

(2) SINGLE-POLE TOGGLE SWITCH

LOW VOLTAGE MOMENTARY CONTACT SWITCH

3-POSITION MOMENTARY CONTACT SWITCH

3-POSITION MAINTAINED CONTACT SWITCH

OCCUPANCY SENSOR

SPLIT-WIRED DUPLEX RECEPTACLE

DUPLEX RECEPTACLE

FOURPLEX RECEPTACLE

SIMPLEX RECEPTACLE

125/250V RECEPTACLE

GROUND FAULT CIRCUIT INTERRUPTER DUPLEX RECEPTACLE

GROUND FAULT CIRCUIT INTERRUPTER FOURPLEX

RECEPTACLE

EMERGENCY DUPLEX RECEPTACLE

EMERGENCY FOURPLEX RECEPTACLE

MULTI-OUTLET ASSEMBLY

POWER / TELEPHONE POLE

CORD DROP WITH DUPLEX RECEPTACLE

SPECIAL PURPOSE OUTLET

+48"

AS NOTED

+18"

FLOOR/CEILING

+18"

OS WALL MOUNTED OCCUPANCY SENSOR SWITCH

DUAL RELAY WALL MOUNTED OCCUPANCY SENSOR SWITCH

+48"

+48"OS

FIRE ALARM SYMBOLS

BDT

BDR

FSD

DESCRIPTIONSYMBOL MOUNTING REMARKS

EOL

4" BELOW

CEILING TO TOP

OF DETECTOR

MANUFACTURER

RECOMMENDED

AT VALVE

ON FIRE RISER

CEILING

SIDE OF DUCT

+48"

AT DEVICE(S) TO

BE CONTROLLED

AT DEVICE(S) TO

MONITOR

AT FAN CONTROL

PANEL

COORDINATE

WITH DOOR

INSTALLER

FLOOR

80" MIN AND 96"

MAX; MEASURED

FROM LENS.

IF CEILING IS

LESS THAN 80",

MOUNT WITHIN

6" OF CEILING.

FURNISHED BY FIRE PROTECTION

CONTRACTOR AND INSTALLED AND

CONNECTED BY DIV. 26

COORDINATE WITH DOOR INSTALLER;

SUBSCRIPT 'F' INDICATES TO MOUNT

AT FLOOR LEVEL

FIRE PROTECTION SPRINKLER RISER BELL

FIRE ALARM AUDIO/VISUAL SPEAKER/STROBE

FIRE ALARM AUDIO SPEAKER

MINI AUDIO/VISUAL HORN/STROBE

FIRE ALARM AUDIO/VISUAL HORN/STROBE

FIRE ALARM VISUAL STROBE

MINI AUDIO HORN

AUDIO HORN

WATER FLOOD INDICATOR

MAGNETIC DOOR HOLDER

FAN SHUTDOWN RELAY

MONITOR MODULE

CONTROL MODULE

FIRE ALARM MANUAL STATION

DUCT SMOKE DETECTOR

SMOKE DETECTOR

HEAT DETECTOR

FIRE/SMOKE DAMPER

WATER FLOW INDICATOR

TAMPER SWITCH

END OF LINE DEVICE

BEAM DETECTOR - RECEIVER

BEAM DETECTOR - TRANSMITTER

+90"

4" BELOW

CEILING TO TOP

OF DETECTOR

SUBSCRIPT 'WP' INDICATES THAT A

WEATHER PROOF BACK BOX IS REQ.

SUBSCRIPT 'C' INDICATES CEILING

MOUNTING.

NUMERIC SUBSCRIPT INDICATES

CANDELLA RATING OF STROBE

(I.E. - 15, 75, 110) http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com

HALL

Y E-

TEACHERS PREP.

E-46

E-

TEACHERS PREP.

E-45

E-43

BOYS

E-9

E-41

GIRLS

E-

CLASSROOM

E-

CLASSROOM

CLASSROOM 308

E-16

TEACH. PREP.

CLASSROOM

HALL

E-14A

CLASSROOM

TEACH. PREP.

E-15

CLASSROOM

VESTIBULE

CLASSROOM

ENTRY

CLASSROOM

GIRLS

E-17

E-18

JAN. E-19

LAV.

PRACTICE

E-

E25

E-30

BOYS

CLASSROOM CLASSROOM

HALL

CHORAL

3 4

CLASSROOM

E-32

PRACTICE

E-31

TEACH. PREP.

BAND

PRACTICE

E-27

DRESS

G-9

VESTIBULE

STAGE

ENTRY

G-14

G-8

STORAGE

CORRIDOR

G-7

G-

G-4

G-6

STAIR

VESTIBULE

ENTRY

G-15

G-16

G-3

G-2

STORAGE

HALL

CORRIDOR

ELECTRICAL

G-1A

DRESS

G-1

A-48

STORAGE

CONFERENCE

A-9

WAITING

A-8

V PRINCIPAL

WORK ROOM

TEACHERS

XXX

A-10

SECURITY AREA

PRINCIPAL

A-12

FILE ROOM

WORK &

A-11

A-36

STORAGE

A-7

V PRINCIPAL

STORAGE

A-16

SHOWER

A-35

A-19

A-20

SHOWER

GIRLS LOCKER ROOM

GIRLS TOILET

A-

A-39

A-33

A-34

TOILET

A-21

BOYS TOILET

A-40

A-32

VESTIBULE

TOILET

SHOWER

OFFICE

A-30

A-31

A-30

SHOWER

A-25

A-24

OFFICE

A-25

GIRLS

A-14

BOYS

A-15 HA

A-22

BOYS LOCKER ROOM

A-

A-23

VESTIBULE

A-41 G Y M N A S I U M

VESTIBULE

C O

R R

I D O

R C

O R

R I D

O R

LL 10

GUIDANCE SUITE

V.P.SUITEB-50

OFFICE

B-51

B-6A

PSYCHOLOGIST B-19

B-52

CLINIC

A-

LL B-7

JAN.

B-4

COUNSELOR COUNSELOR

B-5

STORAGE ROOM

B-44

B-6

COUNSELOR

B-

B-36

OFFICE

TEACHER LOUNGE

JAN. OFFICE

B-8

STORAGE

B-9

B-3

ADMINISTRATION HALL

B-18A

WOMEN

B-

B-10

STORAGE

B-17

SERVING

B-18

MEN

B-39

KITCHEN

B-34

LAUNDRY

B-47

B-41

B3A

VESTIBULE

B-1

ENTRY

TEACH PREP.

B-25

RUBBISH STO.

B-26

B-27

EQUIP. STO.

B-28

MEZZ.

EMPL. LOCKERB-29 JAN.

B-

B-30

CAN WASHREC.

B-33

SCULLERY

B-35 B-42

BREAK RM. TOILET

B-14

CAFETERIA

B-

B-11

STAGE AREA

B-12

STORAGE

B-13

STORAGE

B-16

SCIENCE #4

SCIENCE PREP.

D-26

D-50

DRESSING ROOM

OFFICE

D-23A

DEMO.

D-21

D-

D-11

OFFICE

D-

CORRIDOR

C-33

HALL

SCIENCE #2

SCIENCE #1

SCIENCE #3

D-39

LAV

D-37

GIRLS

JAN

D-38

D-36

TEACH PREP.

D-35

CLASSROOM

804802

CLASSROOM

701 703

CLASSROOM

D-

D- 2A

D-

MEDIA CENTER

D-13

COM.

D-3 D-4

CAREERS

D-5

A./V. STOR.

D-6

TEACH PREP.

TEACH WORK

D-49

CLASSROOM

TELECTR.

D-10A

DESK

D-12

MEDIA WORK

D-10

D-

GIRLS

D-17

D-16

LAV.

BOYS

D-15

LAV.

D-19

D-18

JAN

FOODSCLASSROOM

D-

A904

SEWING

TEACH. PREP.

CLASSROOM

Y C-

CLASSROOM

C-28 C-29

CLASSROOM

TEACH. PREP.

CLASSROOM

408 215

CLASSROOM

HALL

CLASSROOM

HALL

ART NO.1

F-3

VESTIBULE

ART NO.2

STORAGE ROOM

F-4

VESTIBULE

F-5

2.4

SMART LAB 2000

F-11

LAV

JAN

F-12

GIRLS

F-13

F-14

LAB

OFF./STOR.

F-8

F-14A

F-10A

LECTURE

F-9

TLC LAB 2000

1,2

ED101

1,2

EL101

1,2

EA101

EXISTING PANEL 'EM2'

EXISTING FIRE ALARM CONTROL

PANEL.

EG102

OVERALL BUILDING

PLAN

SCALE:

NORTH

OVERALL BUILDING PLAN

1" = 20'-0"

NO. DATE REVISIONS

1 2 3 4 5

CHECKED BY: DW

DRAWN BY: SP / SK

ENVISION PROJECT NO: 2025-247.01

DATE:

ISSUE:

04/01/2026

CONSTRUCTION DOCUMENTS

6 7

240 E. MORRIS AVE. SUITE 200

SALT LAKE CITY, UT 84115

P (801) 534-1130 F (801) 534-1080 www.envisioneng.com

Fil e N am e:

\25

\20

-2

.00

- A ud ito riu m Up gr ad es \01

_D wg s\E lk

Ri dg e M idd le\

2.d wg La st Pl ott ed

: 2

6/0 3/3

0 @ 6:

:07

P M

By : S

L D

L L

, U T http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com b b b b b a a a a

PANEL 'AX'

PANEL 'A2'

MECHANICAL ROOM

G12

PROJECTION ROOM

G11

VEST.

ENTRY

G14

LOBBY

G13

CORRIDOR

STAIR

STOR.

AUDITORIUM

STAGE

STORAGE

G2 ELEC.

G1A

DRESS

CORRIDOR

A48

CORRIDOR

A48

VEST.

G15

ENTRY

G16

A2-16 A2-22 b aa b

11 8 8

(TYP)

1 1

8 8 b b b

(TYP)

LIGHTING LIFT CONTROLS

NET

(TYP)

ES ES

ESES

(TYP)

'SMP'

(TYP)

'ER-1'

'SC1008'

'DIM'

(TYP)

ED101

LIGHTING

DEMOLITION PLANS

SCALE:1 AUDITORIUM - LIGHTING DEMOLITION PLAN

1/8" = 1'-0"SCALE:2 PROJECTION ROOM - LIGHTING DEMOLITION PLAN

1/8" = 1'-0"

GENERAL DEMOLITION NOTES:

1. UNLESS SPECIFICALLY NOTED OTHERWISE, REMOVE ALL ELECTRICAL ITEMS SHOWN IN DARK

& DASHED LINES. LIGHT & SOLID ITEMS ARE TO REMAIN. DEMOLITION ITEMS ARE SHOWN TO

GIVE A BASIC DESCRIPTION OF THE EXTENT OF DEMOLITION WORK, BUT MAY NOT BE

INCLUSIVE. PROVIDE DEMOLITION WORK IN ACCORDANCE WITH THE FOLLOWING

REQUIREMENTS:

1.1. DISCONNECT AND REMOVE ANY/ALL FIXTURES, DEVICES, EQUIPMENT, ETC. REQUIRED

FOR PROPER COMPLETION OF THE WORK WHETHER SHOWN OR NOT.

1.2. RELOCATE, REWIRE, AND/OR RECONNECT ANY/ALL FIXTURES, DEVICES, EQUIPMENT, ETC.

THAT FOR ANY REASON OBSTRUCTS CONSTRUCTION.

1.3. LEAVE ALL EXISTING FIXTURES, DEVICES, EQUIPMENT, ETC. IN PORTIONS OF THE

BUILDING NOT BEING REMODELED, IN WORKING CONDITION. RESTORE ALL INTERRUPTED

BRANCH CIRCUITS, FEEDERS, ETC.

1.4. REMOVE AND DISPOSE OF ALL RACEWAYS, CONDUCTORS, BOXES, DEVICES, EQUIPMENT,

ETC. THAT ARE NOT TO BE REUSED. TERMINATE AT ACCESSIBLE JUNCTION BOX BY

PROVIDING PROPER KNOCK-OUT CLOSURE, TAPE CONDUCTORS, LABEL AS "SPARE" WITH

CIRCUIT NO., ZONE NO, OR OTHER CHARACTERISTIC IDENTIFYING SOURCE.

1.5. EXISTING RACEWAYS MAY BE REUSED, IF IN PLACE, WHERE POSSIBLE, AND WHERE IN

COMPLIANCE WITH THE SPECIFICATIONS AND THE INTENT OF THE CONTRACT

DOCUMENTS. UPGRADE AND OR PROVIDE NEW CONDUIT SUPPORTS WHERE

NECESSARY FOR ALL RACEWAYS BEING REUSED. ENSURE INTEGRITY OF EXISTING

RACEWAYS BEFORE REUSE.

1.6. CONCEAL ALL RACEWAY AND WIRING IN EXISTING WALLS, CEILINGS, FLOORS, ETC. THE

USE OF WIREMOLD IS PERMITTED ONLY WHERE SPECIFICALLY NOTED ON DRAWING.

1.7. DO NOT PENETRATE STRUCTURAL ELEMENTS OF FLOORS, WALLS, CEILINGS, ROOFS,

ETC.

1.8. COORDINATE WITH JORDAN SCHOOL DISTRICT WHAT EQUIPMENT SHOULD BE DISPOSED

OF AND WHAT EQUIPMENT IS TO BE RETURNED TO JORDAN SCHOOL DISTRICT.

1.9. FIRE ALARM SYSTEM MUST REMAIN OPERATIONAL DURING ALL PHASES OF

CONSTRUCTION.

2. REMOVE ANY UNUSED BRANCH CIRCUITS BACK TO THE SOURCE COMPLETELY. TURN OFF

BREAKER AND LABEL 'SPARE'.

3. BRANCH CIRCUITS, IF SHOWN WERE TAKEN FROM EXISTING RECORD DRAWINGS AND PANEL

SCHEDULES AND MAY NOT BE ACCURATE. CONTRACTOR TO TRACE OUT ALL CIRCUITS PRIOR

TO ANY DEMOLITION.

4. THIS AND ANY OTHER DEMOLITION DRAWINGS ARE NOT INTENDED TO BE ALL-INCLUSIVE, NOR

TO DEFINE THE SCOPE OF ALL DEMOLITION WORK REQUIRED FOR THIS PROJECT. DEMOLITION

DRAWINGS ARE SHOWN ONLY TO AID THE CONTRACTOR IN PREPARING THE BID AND

PERFORMING THE WORK. CONTRACTOR SHALL EXAMINE ALL CONTRACT DOCUMENTS AND

VISIT THE SITE DURING BIDDING TO DETERMINE THE TOTAL EXTEND AND SCOPE OF THE

DEMOLITION PORTION OF THIS WORK. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL

DEMOLITION WORK REQUIRED TO CARRY OUT THE WORK AS SOWN IN THE CONTRACT

DOCUMENTS.

NO. DATE REVISIONS

1 2 3 4 5

CHECKED BY: DW

DRAWN BY: SP / SK

ENVISION PROJECT NO: 2025-247.01

DATE:

ISSUE:

04/01/2026

CONSTRUCTION DOCUMENTS

6 7

240 E. MORRIS AVE. SUITE 200

SALT LAKE CITY, UT 84115

P (801) 534-1130 F (801) 534-1080 www.envisioneng.com

Fil e N am e:

\25

\20

-2

.00

- A ud ito riu m Up gr ad es \01

_D wg s\E lk

Ri dg e M idd le\

1.d wg La st Pl ott ed

: 2

6/0 3/3

0 @ 6:

:09

P M

By : S

L D

L L

, U T

KEYED NOTES:

1. EXISTING MOTORIZED LIGHTING LIFT, NETWORK JACK, DMX GATWAY AND CONTROLS TO REMAIN

IN PLACE. PROTECT FROM DAMAGE DURING ALL PHASES OF THE CONSTRUCTION.

2. EXISTING LIGHTING BATTEN, NETWORK JACK AND DMX GATWAY TO REMAIN IN PLACE. PROTECT

FROM DAMAGE DURING ALL PHASES OF THE CONSTRUCTION.

3. EXISTING ETC THEATRICAL EMERGENCY LIGHTING CONTROLS TO REMAIN IN PLACE.

4. EXISTING ETC DIMMING RACK AND EXISTING BRANCH CIRCUIT TO REMAIN IN PLACE. SEE

DEMOLITION RISER DIAGRAM ON SHEET EL501 FOR DEMOLITION SCOPE OF WORK. PROTECT

FROM DAMAGE DURING ALL PHASES OF THE CONSTRUCTION..

5. EXISTING ETC EQUIPMENT RACK, EXISTING BRANCH CIRCUIT AND CONTROL WIRING TO REMAIN

IN PLACE. PROTECT FROM DAMAGE DURING ALL PHASES OF THE CONSTRUCTION. ANY DAMAGE

DONE TO THIS RACK DURING THIS CONSTRUCTION WILL BE REPLACED OR REPAIRED AT NO

ADDITIONAL COST TO THE OWNER..

6. EXISTING ETC EQUIPMENT STAGE MANAGER RACK, EXISTING BRANCH CIRCUIT AND CONTROL

WIRING TO REMAIN IN PLACE. PROTECT FROM DAMAGE DURING ALL PHASES OF THE

CONSTRUCTION. ANY DAMAGE DONE TO THIS RACK DURING THIS CONSTRUCTION WILL BE

REPLACED OR REPAIRED AT NO ADDITIONAL COST TO THE OWNER.

7. EXISTING TWIST LOCK THEATRICAL RECEPTACLE TO REMAIN IN PLACE. PROTECT FROM

DAMAGE DURING ALL PHASES OF THE CONSTRUCTION.

8. EXISTING ENTRY STATION TO REMAIN IN PLACE PROTECT FROM DAMAGE DURING ALL PHASES

OF THE CONSTRUCTION.

9. DISCONNECT, REMOVE AND DISPOSE OF EXISTING THEATRICAL LIGHTING FIXTURES. REMOVE

ALL HANGERS AND CONNECTORS COMPLETELY, UNLESS OTHERWISE DIRECTED BY THE

THEATRICAL LIGHTING SUPPLIER / INSTALLER.

10. DISCONNECT, REMOVE AND DISPOSE OF EXISTING RECESSED CAN LIGHTS. REMOVE EXISTING BRANCH CIRCUIT BACK TO THE SOURCE OR NEXT LIGHT FIXTURE THAT IS TO REMAIN IN PLACE.

CONTRACTOR TO TRACE OUT CIRCUIT TO DETERMINE EXACT BRANCH CIRCUIT AND WHAT IS

CONNECT TO THE CIRCUIT PRIOR TO THE START OF THE DEMOLITION.

11. UNLESS OTHERWISE DIRECTED BY THE OWNER DISPOSE OF ALL EXISTING THEATRICAL

LIGHTING FIXTURES THAT ARE STORED IN THIS AREA.

12. EXISTING ETC NETWORK CONNECTIONS TO REMAIN IN PLACE. PROTECT FROM DAMAGE DURING

ALL PHASES OF THE CONSTRUCTION.

13. DISCONNECT, REMOVE AND RETURN TO OWNER EXISTING TOUCH SCREEN AND LIGHTING

CONSOLE.

14. DISCONNECT, REMOVE AND DISPOSE OF EXISTING RECESSED DOWN LIGHTS. EXISTING DIMMING

CIRCUIT TO REMAIN IN PLACE FOR REUSE. CONTRACTOR TO TRACE OUT DIMMING CIRCUIT TO

DETERMINE FIXTURES THAT ARE ON THE CIRCUIT PRIOR TO THE START OF THE DEMOLITION.

15. DISCONNECT, REMOVE AN DISPOSE OF EXISTING LIGHTING CONTROL FOR PROJECTION ROOM RECESSED DOWN LIGHTS. IF REUSED EXISTING CIRCUIT TO REMAIN IN PLACE FOR REUSE, SEE

NEW LIGHTING PLAN FOR REQUIREMENTS. COORDINATE ALL WORK WITH THE THEATRICAL

LIGHTING SYSTEM INSTALLER PRIOR TO THE START OF THE DEMOLITION.

DIMMING NOTES:

FRONT OF HOUSE - DIM 1-24

1ST ELECTRIC - DIM 25-51

2ND ELECTRIC - DIM 52-60

3RD ELECTRIC - DIM 63-72

TWIST LOCK RECEPTACLES - DIM 79 (BOOTH), 80-83 (STAGE)

HOUSE LIGHTING - DIM 85-96

ASSUMED SPARE - DIM 61,62,73-78

CONTRACTOR TO VERIFY ALL DIMMING CIRCUITS AND UPDATE AS NECESSARY TO

REFLECT AS-BUILT CONDITIONS.

LIGHTING ALTERNATE #1.

BASE BID - IT IS ASSUMED THE EXISTING HOUSE LIGHTS IN THE AUDITORIUM HAVE

BEEN UPGRADED TO LED. EXISTING LIGHTING TO REMAIN IN PLACE AND BE

CONTROLLED THROUGH THE NEW THEATRICAL LIGHTING CONTROL SYSTEM.

ALTERNATE - REMOVE AND REPLACE LIGHTING AS SHOWN WITH NEW LED.

AutoCAD SHX Text 4.1

AutoCAD SHX Text

AutoCAD SHX Text 4.9

AutoCAD SHX Text

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text C

AutoCAD SHX Text C1

AutoCAD SHX Text E

AutoCAD SHX Text 4.9

AutoCAD SHX Text 4.1

AutoCAD SHX Text

AutoCAD SHX Text E

AutoCAD SHX Text D http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com http://www.envisioneng.com a a a a a

ES ES

ESES

b b b b a a a a

PANEL 'AX'

PANEL 'A2'

MECHANICAL ROOM

G12

PROJECTION ROOM

G11

VEST.

ENTRY

G14

LOBBY

G13

CORRIDOR

STAIR

STOR.

AUDITORIUM

STAGE

STORAGE

ELEC.

G1A

DRESS

CORRIDOR

A48

CORRIDOR

A48

VEST.

G15

ENTRY

G16 b aa b

DMX

(TYP)

DL2

A2-16 A2-22 b b b b

CSSV CSSV

(TYPICAL OF 12) (TYPICAL OF 12)

CSSV

(TYPICAL OF 13)

PAR

(TYPICAL OF 7)

4 4 4 4 4 4

CYC

(TYPICAL OF 12)

CSSV

(TYPICAL OF 13)

PAR

(TYPICAL OF 7)

NET

'ER-1'

'SC1008'

'DIM'

'SMP'

LIGHTING LIFT CONTROLS

(TYP)

DL1 DL1

DL1

DL1 DL1

DL1

'EBDK'

'DEBC-1'

NO. DATE REVISIONS

1 2 3 4 5

CHECKED BY: DW

DRAWN BY: SP / SK

ENVISION PROJECT NO: 2025-247.01

DATE:

ISSUE:

04/01/2026

CONSTRUCTION DOCUMENTS

6 7

240 E. MORRIS AVE. SUITE 200

SALT LAKE CITY, UT 84115

P (801) 534-1130 F (801) 534-1080 www.envisioneng.com

Fil e N am e:

\25

\20

-2

.00

- A ud ito riu m Up gr ad es \01

_D wg s\E lk

Ri dg e M idd le\

1.d wg La st Pl ott ed

: 2

6/0 3/3

0 @ 6:

:12

P M

By : S

L D

L L

, U T

EL101

LIGHTING PLANS

SCALE:1 AUDITORIUM - LIGHTING PLAN

1/8" = 1'-0"SCALE:2 PROJECTION ROOM - LIGHTING PLAN

1/8" = 1'-0"

GENERAL NOTES:

1. ANY EXISTING CONDUITS, BOXES, ETC. THAT ARE LOCATED IN THE AFFECTED CONSTRUCTION

AREA AND THAT INTERFERE WITH CONSTRUCTION SHALL BE RELOCATED OR REROUTED AS

NECESSARY.

2. THE CONTRACTOR SHALL TRACE ALL EXISTING CIRCUITS AND CONFIRM ALL DEVICES ON THE

CIRCUIT PRIOR TO ANY DEMOLITION.

3. CONTRACTOR TO PROVIDE NEW CEILING TILES AS NECESSARY FOR ANY AND ALL CEILING

TILES DAMAGED DUE TO THIS CONSTRUCTION. OWNER TO ASSIST CONTRACTOR IN OBTAINING

THE CORRECT CEILING TILES TO MATCH THE EXISTING INSTALLED.

4. REFER TO LIGHTING CONTROL SHEETS FOR TYPICAL CONTROL WIRING DIAGRAMS. PROVIDE

COMPLETE SYSTEM WITH ALL REQUIRED CONDUIT, WIRING, SWITCHES, SENSORS, POWER

PACK, ETC.

5. LOCATE POWER PACKS AND ROOM CONTROLLERS ABOVE ACCESSIBLE CEILING NEAR ROOM

ENTRANCES. WHERE ROOM DOES NOT HAVE AN ACCESSIBLE CEILING MOUNT IN AN

ACCESSIBLE LOCATION IN EQUIPMENT OR ELECTRICAL ROOMS AND LABEL CONTROLLER WITH

ROOM SERVED.

6. EXACT LOCATION OF LIGHT FIXTURES SHALL BE AS SHOWN ON THE ENGINEER'S REFLECTED

CEILING PLAN.

7. CEILING MOUNTED OCCUPANCY SENSORS SHALL NOT BE INSTALLED WITHIN 6 FEET OF ANY

MECHANICAL DIFFUSER.

8. THE CONTRACTOR SHALL DETERMINE THE EXACT ROUTING OF ALL CONDUITS AND CABLES IN

THE FILED. THIS PLAN REPRESENTS A SCHEMATIC REPRESENTATION OF DEVICE AND

EQUIPMENT LOCATIONS.

9. DO NOT CONNECT, MOUNT OR SUPPORT ANY ELECTRICAL FROM DATA / COMM MOUNTING OR

WIRE MANAGEMENT.

10. CABLING SHALL BE RUN PERPENDICULAR AND PARALLEL TO SURFACES OF STRUCTURAL

MEMBERS, AND FOLLOW SURFACE CONTOURS WHERE POSSIBLE.

11. CONTRACTOR SHALL COORDINATE ALL WALL MOUNTED DEVICES, FIXTURES AND EQUIPMENT

HEIGHTS AND LOCATIONS WITH THE ELECTRICAL ENGINEER PRIOR TO ANY ROUGH-IN.

KEYED NOTES:

1. CONTRACTOR TO HIRE A DRYWALL INSTALLER TO REPAIR EXISTING CEILING OPENING WHERE THE EXISTING LIGHT FIXTURES WERE REMOVED. PAINT CEILING TO MATCH EXISTING FINISHES.

CONFIRM COLOR WITH THE OWNER PRIOR TO PAINTING.

2. SEE RISER DIAGRAM ON SHEET EL501 FOR SCOPE OF WORK FOR THE DIMMING RACK.

3. CONNECT TO SPARE RELAY IN THE DIMMING RACK. NOTE RELAY USED ON THE REDLINE

AS-BUILT DRAWINGS. COORDINATE INSTALLATION REQUIREMENTS WITH THE THEATRICAL

LIGHTING SYSTEM SUPPLIER/ INSTALLER PRIOR TO ANY ROUGH-IN. NEW RECESSED DOWN

LIGHTS TO BE CONTROLLED BY THE THEATRICAL LIGHTING SYSTEM AND MANUAL DMX WALL

CONTROL.

4. CYC LIGHT FIXTURE ON THE STAGE FLOOR.

5. INSTALL NEW TOUCH SCREENS AND CONSOLE. SEE RISER DIAGRAM ON SHEET EL501 FOR

ADDITIONAL INFORMATION.

6. INSTALL NEW RECESSED DOWN LIGHT FIXTURE IN EXISTING LOCATION. RECONNECT TO THE

EXISTING DIMMING CIRCUIT THAT WAS IN PLACE PRIOR TO THE DEMOLITION.

DIMMING NOTES:

FRONT OF HOUSE - DIM 1-24

1ST ELECTRIC - DIM 25-51

2ND ELECTRIC - DIM 52-60

3RD ELECTRIC - DIM 63-72

TWIST LOCK RECEPTACLES - DIM 79 (BOOTH), 80-83 (STAGE)

HOUSE LIGHTING - DIM 85-96

ASSUMED SPARE - DIM 61,62,73-78

CONTRACTOR TO VERIFY ALL DIMMING CIRCUITS AND UPDATE AS NECESSARY TO

REFLECT AS-BUILT CONDITIONS.

LIGHTING ALTERNATE #1.

BASE BID - IT IS ASSUMED THE EXISTING HOUSE LIGHTS IN THE AUDITORIUM HAVE

BEEN UPGRADED TO LED. EXISTING LIGHTING TO REMAIN IN PLACE AND BE

CONTROLLED THROUGH THE NEW THEATRICAL LIGHTING CONTROL SYSTEM.

ALTERNATE - REMOVE AND REPLACE LIGHTING AS SHOWN WITH NEW LED.

AutoCAD SHX Text 4.1

AutoCAD SHX Text

AutoCAD SHX Text 4.9

AutoCAD SHX Text

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text C

AutoCAD SHX Text C1

AutoCAD SHX Text E

AutoCAD SHX Text 4.9

AutoCAD SHX Text 4.1

AutoCAD SHX Text

AutoCAD SHX Text E

EL501

LIGHTING RISER

DIAGRAM AND

FIXTURE SCHEDULE

NO. DATE REVISIONS

1 2 3 4 5

CHECKED BY: DW

DRAWN BY: SP / SK

ENVISION PROJECT NO: 2025-247.01

DATE:

ISSUE:

04/01/2026

CONSTRUCTION DOCUMENTS

6 7

240 E. MORRIS AVE. SUITE 200

SALT LAKE CITY, UT 84115

P (801) 534-1130 F (801) 534-1080 www.envisioneng.com

Fil e N am e:

\25

\20

-2

.00

- A ud ito riu m Up gr ad es \01

_D wg s\E lk

Ri dg e M idd le\

1.d wg La st Pl ott ed

: 2

6/0 3/3

0 @ 6:

:15

P M

By : S

L D

L L

, U T

KEYED NOTES:

1. EXISTING DIMMER RACK TO REMAIN IN PLACE.

2. ETC CERTIFIED TECHNICIAN TO REMOVE ALL 96 EXISTING D20 MODULES AND FAN FROM THE

EXISTING DIMMER RACK. CONFIRM ALL REQUIREMENTS WITH ETC PRIOR TO THE BID.

3. DISCONNECT, REMOVE AND RETURN TO OWNER EXISTING TOUCH SCREEN AND LIGHTING

CONSOLE.

4. ETC CERTIFIED TECHNICIAN TO INSTALL 48 NEW R20 DUAL RELAY MODULES AND NEW FAN IN

THE EXISTING DIMMER RACK. ETC CERTIFIED TECHNICIAN TO RECONFIGURE THE CONTROL

ELECTRONICS AS NECESSARY FOR NEW RELAY MODULES. CONFIRM ALL REQUIREMENTS WITH

ETC PRIOR TO THE BID.

5. CONTRACTOR TO CONFIRM IF EXISTING AUDITORIUM HOUSE LIGHTING IS DMX OR 0-10V

DIMMING. PROVIDE INFORMATION TO ETC PRIOR TO ORDERING EQUIPMENT.

6. PROVIDE NEW FIRE ALARM DEVICE AS SHOWN. CONNECT NEW DEVICE INTO THE EXISTING

INITIATING DEVICE LOOP AS DIRECTED BY THE FIRE ALARM SYSTEM SUPPLIER. NEW DEVICE TO

BE OF THE SAME MANUFACTURE (FCI E3) AS THE EXISTING INSTALLED. CONFIRM ALL

REQUIREMENTS WITH THE FIRE ALARM SYSTEM SUPPLIER AND THEATRICAL EQUIPMENT

INSTALLER PRIOR TO THE START OF THE CONSTRUCTION.

7. BREAKER IS ASSUMED TO BE SPARE. CONFIRM PRIOR TO THE START OF THE CONSTRUCTION.

CONFIRM ALL POWER REQUIREMENTS WITH THE THEATRICAL EQUIPMENT INSTALLER PRIOR TO

THE START OF THE CONSTRUCTION.

TO EXISTING

DISTRIBUTION PANEL

(800A, 120/208V, 3 PHASE)

SCALE:1 THEATERICAL LIGHTING SYSTEM DEMOLITION RISER DIAGRAM

NONE

CONTROL WIRING LEGEND

Symbol Wire type(s) Signal

(1) BELDEN 1583A NETWORK

(1) BELDEN 8471

(1) #14 AWG.STRANDED WIRE

ECHOCONNECT

(2) #16 AWG.STRANDED WIRES AUXILIARY

(2) #16 AWG. STRANDED WIRE PANIC

(1) BELDEN 1583A 9729 DMX

(3) #12 AWG. SOLID WIRE POWER

USB USB

Approved Wire Type Alternates can be found here:

https://www.etcconnect.com/cablecross

USBUSB

NEW 24" M8299

TOUCH MONITOR

NEW

ION XE 2K US

CONTROL CONSOLE

PROJECTION

BOOTH

USB

NOTES:

1. LED PROFILE LIGHT ENGINE FIXTURES INCLUDES POWER INPUT CONNECTOR, RGBI-L, 19 DEGREE LENS TUBE, 26 DEGREE LENS TUBE, 36 DEGREE LENS TUBE, C-CLAMP, SAFETY CABLE, POWER CABLE AND DMX CABLE.

CONTRACTOR TO VERIFY LENGTH OF POWER CABLE AND DMX CABLE PRIOR TO ORDERING. COORDINATE EXACT

FIXTURE LOCATIONS AND AIMING WITH OWNER.

2. LED ZOOM SPOT FIXTURES INCLUDES POWER INPUT CONNECTOR, RGBI-L, C-CLAMP, SAFETY CABLE, POWER CABLE AND DMX CABLE. CONTRACTOR TO VERIFY LENGTH OF POWER CABLE AND DMX CABLE PRIOR TO

ORDERING. COORDINATE EXACT FIXTURE LOCATIONS AND AIMING WITH OWNER.

3. LED CYC FIXTURES INCLUDES POWER INPUT CONNECTOR, RGBI-L, C-CLAMP, SAFETY CABLE, POWER CABLE AND DMX CABLE. CONTRACTOR TO VERIFY LENGTH OF POWER CABLE AND DMX CABLE PRIOR TO ORDERING.

COORDINATE EXACT FIXTURE LOCATIONS AND AIMING WITH OWNER.

4. LIGHTS TO BE CONTROLLED BY THE THEATRICAL LIGHTING SYSTEM AND LOCAL CONTROL IN THE PROJECTION

ROOM.

DESCRIPTION TYPE MFG PART NUMBER NOTES

COLOR SOURCE SPOT V CSSV ETC CSSPOTVMVS NOTE 1

COLOR SOURCE PAR V NOTE 2CSPARVZMV

THEATRICAL AND HOUSE LIGHT FIXTURE SCHEDULE

COLOR SOURCE CYC CYC ETC NOTE 3

PAR ETC

CSCYC

6" RECESSED DOWN LIGHT DL1 GOTHAM IV06 ADJ 50LM 35K 80CRI 60D DARK MVOLT

DMX NCH AC AR LSS F

'SC1008'

'DIM'

'ER-1'

LIGHTING

FIXTURES

AND

RECEPTACLES

TO EXISTING

EMERGENCY LIGHTS

TO EXISTING

EMERGENCY PANEL

(20A, 120-277V, 1

PHASE)

TO EXISTING

PANELBOARD

(20A, 120V, 1 PHASE)

ETC NET PLUG-IN

STATION

(FIRST ELECTRIC)

ETC NET PLUG-IN

STATION

(FIRST ELECTRIC)

ETC NET PLUG-IN

STATION

(FOH CATWALK)

ETC NET PLUG-IN

STATION

(FOH CATWALK)

ETC NET PLUG-IN

STATION

(THIRD ELECTRIC)

ETC NET PLUG-IN

STATION

(THIRD ELECTRIC)

ETC NET PLUG-IN

STATION

(SECOND ELECTRIC)

ETC NET PLUG-IN

STATION

(SECOND ELECTRIC)

N/N PLUG-IN STATION

(CONTROL BOOTH)

ELEMENT 2

CONTROL SYSTEM

NET3

2-PORT GATEWAY

(TYP OF 6)

'SMP'

TO EXISTING

PANELBOARD

(20A, 120V, 1 PHASE)

WAP

HL1 - UH10002

CONTROL BOOTH

LADDER

HL1 - UH10002

CONTROL BOOTH

LADDER

HL1 - UH10002

CATWALK

LADDER

HL1 - UH10002

CONTROL BOOTH

HL1 - UH10002

CATWALK

TO EXISTING

DISTRIBUTION PANEL

(800A, 120/208V, 3 PHASE)

SCALE:2 THEATERICAL LIGHTING SYSTEM RISER DIAGRAM

NONE

'SC1008'

'DIM'

'ER-1'

LIGHTING

FIXTURES

AND

RECEPTACLES

TO EXISTING

EMERGENCY LIGHTS

TO EXISTING

EMERGENCY PANEL

(20A, 120-277V, 1

PHASE)

TO EXISTING

PANELBOARD

(20A, 120V, 1 PHASE)

ETC NET PLUG-IN

STATION

(FIRST ELECTRIC)

ETC NET PLUG-IN

STATION

(FIRST ELECTRIC)

ETC NET PLUG-IN

STATION

(FOH CATWALK)

ETC NET PLUG-IN

STATION

(FOH CATWALK)

ETC NET PLUG-IN

STATION

(THIRD ELECTRIC)

ETC NET PLUG-IN

STATION

(THIRD ELECTRIC)

ETC NET PLUG-IN

STATION

(SECOND ELECTRIC)

ETC NET PLUG-IN

STATION

(SECOND ELECTRIC)

N/N PLUG-IN STATION

(CONTROL BOOTH)

NET3

2-PORT GATEWAY

(TYP OF 6)

'SMP'

TO EXISTING

PANELBOARD

(20A, 120V, 1 PHASE)

WAP

HL1 - UH10002

CONTROL BOOTH

LADDER

HL1 - UH10002

CONTROL BOOTH

LADDER

HL1 - UH10002

CATWALK

LADDER

HL1 - UH10002

CONTROL BOOTH

HL1 - UH10002

CATWALK

NEW 24" M8299

TOUCH MONITOR

DIMMING NOTES:

FRONT OF HOUSE - DIM 1-24

1ST ELECTRIC - DIM 25-51

2ND ELECTRIC - DIM 52-60

3RD ELECTRIC - DIM 63-72

TWIST LOCK RECEPTACLES - DIM 79 (BOOTH), 80-83 (STAGE)

HOUSE LIGHTING - DIM 85-96

ASSUMED SPARE - DIM 61,62,73-78

CONTRACTOR TO VERIFY ALL DIMMING CIRCUITS AND UPDATE AS NECESSARY TO

REFLECT AS-BUILT CONDITIONS.

TO FIRE ALARM SYSTEM

NEW

EBDK

TO FIRE ALARM SYSTEM

NEW

DEBC-1

TO NORMAL / EMERGENCY

DMX CONTROLLED FIXTURES

Z 6

NEW 120V, 20A

CIRCUIT - A2-41

NEW 120V, 20A

EMERGENCY

CIRCUIT

EM2-33

4" RECESSED DOWN LIGHT DL2 GOTHAM NOTE 4EVO ARTC RGBW/12 4AR MD LSS 120 DMX

TRW

(TYP)

MECHANICAL ROOM

G12

PROJECTION ROOM

G11

VEST.

ENTRY

G14

LOBBY

G13

CORRIDOR

STAIR

STOR.

AUDITORIUM

STAGE

STORAGE

ELEC.

G1A

DRESS

CORRIDOR

A48

CORRIDOR

A48

VEST.

G15

ENTRY

G16

HBR NCONSOLE

V E V E

S E S E

A2TO

PROJ

FROM FIELD

DEVICES

SPEAKERS

L(14)

HBT E

SUBSUB

FOLDFOLD

EEE

UI1 N

V E V E

11 12

6 6

10 6 10

7 74

9 9

S L(14)

EA101

AUDIO VISUAL

PLANS

SCALE:1 AUDITORIUM - AUDIO VISUAL PLAN

1/8" = 1'-0"SCALE:2 PROJECTION ROOM - AUDIO VISUAL PLAN

1/8" = 1'-0"

NO. DATE REVISIONS

1 2 3 4 5

CHECKED BY: DW

DRAWN BY: SP / SK

ENVISION PROJECT NO: 2025-247.01

DATE:

ISSUE:

04/01/2026

CONSTRUCTION DOCUMENTS

6 7

240 E. MORRIS AVE. SUITE 200

SALT LAKE CITY, UT 84115

P (801) 534-1130 F (801) 534-1080 www.envisioneng.com

Fil e N am e:

\25

\20

-2

.00

- A ud ito riu m Up gr ad es \01

_D wg s\E lk

Ri dg e M idd le\

1.d wg La st Pl ott ed

: 2

6/0 3/3

0 @ 6:

:18

P M

By : S

L D

L L

, U T

GENERAL NOTES:

1. NEW CABLING IS REQUIRED FOR ALL NEW, IN WALL DEVICES. EXISTING CABLES MAY BE

REUSED FOR ALL EXISTING DEVICES, IF IN GOOD CONDITION.

KEYED NOTES:

1. INSTALL NEW 'HBT' IN DOUBLE GANG SURFACE MOUNT JUNCTION BOX AT OUTLET HEIGHT.

1.1. INSTALL AUTO MODE 'PB' IN SINGLE GANG BOX, AT SWITCH HEIGHT.

1.2. PROVIDE MIN 1" C BETWEEN 'HBT' AND 'PB' PROVIDE ADDITIONAL 1" C. FROM 'PB' TO

ACCESSIBLE CEILING ABOVE AUDITORIUM. PROPERLY MOUNT AND SUPPORT CONDUIT

AND CABLE, ACCORDING TO BEST PRACTICES.

2. INSTALL 'HBR' IN RACK 'A2'. CONNECT OUTPUT TO AVAILABLE DIGITALINX INPUT.

3. REPLACE EXISTING SPEAKER DRIVER, AND CONNECT TO EXISTING SPEAKER CABLES. CLEAN

AND REUSE EXISTING BACK CAN AND GRILLE.

4. EXISTING POLE MOUNTED PROJECTOR, REMOVE EXISTING PROJECTOR, AND INSTALL NEW

PROJECTOR IN EXISTING LOCATION. DELIVER EXISTING PROJECTOR TO OWNER FOR FINAL

DISPOSITION.

5. REMOVE EXISTING WALL MOUNTED GIMBAL SPEAKER, DISCONNECT SPEAKER CABLE, CAP ENDS

WITH WIRE NUT, AND TUCK BEHIND ADJACENT SPEAKER GRILL.

6. REMOVE EXISTING FOLD BACK SPEAKER. DEMO CABLE BACK TO SOURCE. INSTALL PULL STRING

IN CONDUIT, AND LABEL BOTH ENDS.

7. REMOVE EXISTING AUDIENCE DELAY FILL SPEAKERS, AND CABLE. INSTALL PULL STRING, LABEL

AND SECURE AT BOTH ENDS.

8. REMOVE EXISTING AV DEVICE, INSTALL NEW AV DEVICE IN ITS PLACE.

9. REMOVE EXISTING AV DEVICE, AND CABLE. INSTALL PULL STRING, LABEL AND SECURE AT BOTH

ENDS. INSTALL STAINLESS STEEL COVER PLATE.

10. FLY SUBWOOFER AND SIDE FILL (EFFECTS) SPEAKER ABOVE CEILING AIMED THROUGH GRILL

CLOTH. ADJUST SPEAKERS TO PROVIDE EVEN COVERAGE OF AUDITORIUM. MAXIMUM +/- 2DB

SEAT TO SEAT VARIATION.

11. REMOVE EXISTING AUX IN AND MIC PLATE, AND JUNCTION BOX ON WALL AT OUTLET HEIGHT.

INSTALL NEW USER INTERFACE 'UI1' IN DEEP DOUBLE GANG SURFACE MOUNT BOX AT SWITCH

HEIGHT.

12. REMOVE EXISTING DANTE MIC INPUT/OUTPUT PLATE. INSTALL NEW 'HBT' IN ITS PLACE.

13. INSTALL WIRELESS MIC ANTENNA ON SIDE OF PROSCENIUM WALL, NEAR TOP. IF SURFACE

MOUNT RACEWAY IS REQUIRED, IMMEDIATELY ROUTE AROUND SIDE WALL. PAINT AND TOUCH

UP RACEWAY TO MATCH WALL OR CURTAIN.

AutoCAD SHX Text 4.1

AutoCAD SHX Text

AutoCAD SHX Text 4.9

AutoCAD SHX Text

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text C

AutoCAD SHX Text C1

AutoCAD SHX Text E

AutoCAD SHX Text 4.9

AutoCAD SHX Text 4.1

AutoCAD SHX Text

AutoCAD SHX Text E

1 HDMI INPUT

NO SCALE

DOUBLE GANG

FACEPLATE WITH

DECORA INSERTS

HBT

HDMI IN

2 AUTO MODE PUSH BUTTON

NO SCALE

TRIPPLE GANG

FACEPLATE WITH

DECORA INSERTS

UI1

AUTO

LIGHTED

MOMENTARY

PUSH BUTTON

ENGRAVED TEXT

W/CONTRASTING

COLOR, TYPICAL

RCA CONNECTORS

3.5mm CONNECTORS

DOUBLE GANG

FACEPLATE WITH

DECORA INSERTS

BLUETOOTH

RECEIVER

IN 3/4 A

IN 3/4 B

OUT 1/2 A

PAIR

QTYSYM DESCRIPTION ACCEPTABLE TYPES

MIXING CONSOLE, AUDIO W/

DANTE LINK CARDCONSOLE 1 EXISTING

AV EQUIPMENT CABINET, FLOOR STANDING 0 EXISTING

A2 AV EQUIPMENT CABINET, ON COUNTER 0 EXISTING

HDMI HDBASET WALL TRANSMITTER EXTRON DTP3 T 101 DOFPHBT

V 0VOLUME CONTROL, EXISTING EXISTING

USER INTERFACE PLATE

AUTO MODE BUTTON

METAL DECORA INSERT PLATE

LIGHTED MOMENTARY PUSH BUTTON

24VDC POWER SUPPLY FOR LED

SEE DETAIL

CUSTOM, BLACK

SCHNEIDER, XB6ECW3B2P OR EQUAL)

RDL PS-24AS INSTALL IN RACK

OFP

1/PLATE

1/EA

UI1

BLUETOOTH CONNECTION PLATE W/

TWISTED PAIR RECEIVER

RDL D-BTN21

RDL TX TPR3A

1/PLATE

S RECESSED SPEAKER, SQUARE, 8", EXISTING W/

SPEAKER DRIVER

SPEAKER BACK BOX

SPEAKER GRILL

ATLAS SOUND CX803

REUSE EXISTING

CLEAN, TOUCHUP PAINT, AND REINSTALL

OFP

1/EA

PROJ

PROJECTOR, POLE MOUNTED, IN EXISTING LOCATION EPSON EB-PU2216B W/ ELPLM15 LENS1

AUDIO-VIDEO CABLE EQUIPMENT LIST

SYM DESCRIPTION QTY ACCEPTABLE TYPES

GENERAL PROJECT NOTES

CONTROL CABLE, WHITE JACKET (X) INDICATES

NUMBER OF CABLES, IF MORE THAN ONE

A/R BELDEN 1872A

WEST PENN 4246

LIBERTY 24-4P-L6-EN

OR AS APPROVED BY CONSULTANT

MICROPHONE CABLE, (X) INDICATES NUMBER OF

CABLES, IF MORE THAN ONE

A/R LIBERTY 22-1P-EZ

BELDEN 9451

WEST PENN 454

OR AS APPROVED BY CONSULTANT

HDBASE T CABLE, BLACK JACKET,

(X) INDICATES NUMBER OF CABLES, IF MORE THAN

ONE

A/R WEST PENN 4246AF

COMMSCOPE 1291B F/UTP

OR AS APPROVED BY CONSULTANT

LINE LEVEL CABLE, (X) INDICATES NUMBER

OF CABLES, IF MORE THAN ONE

A/R BELDEN 9451

WEST PENN 454

LIBERTY 22-1P-EZ

OR AS APPROVED BY CONSULTANT

SPEAKER CABLE, (X) INDICATES NUMBER

OF CABLES, IF MORE THAN ONE

A/R BELDEN 8471

WEST PENN 225

LIBERTY 16-2C-GRY

OR AS APPROVED BY CONSULTANT

BELDEN 10GX62F

C(X)

M(X)

H(X)

L(X)

S(X)

MANUFACTURER'S NAMES AND TELEPHONE NUMBERS ARE LISTED IN THE SPECIFICATIONS

A/R = AS REQUIRED

AUDIO-VIDEO EQUIPMENT LIST

ADSP

IN 1

OUT 1

IN 2

IN 3

IN 4

IN 5

IN 6

IN 7

IN 8

FLEX 1

FLEX 2

FLEX 3

FLEX 4

FLEX 5

FLEX 6

FLEX 7

FLEX 8

OUT 2

OUT 3

OUT 4

OUT 5

OUT 6

OUT 7

OUT 8

ADSP

IN 1

IN 2

IN 3

IN 4

IN 5

IN 6

IN 7

IN 8

FLEX 1

FLEX 2

FLEX 3

FLEX 4

FLEX 5

FLEX 6

FLEX 7

FLEX 8

LAN A

LAN B

LAN A

LAN B

DANTE

CONSOLE

DANTE

GPIO 1

GPIO 2

GPIO 3

GPIO 4

GPIO 5

GPIO 6

GPIO 7

GPIO 8

DANTE

RXABT

AMP 1

WMR

UI1

HDMI 1

HDMI 2

HDMI 3

BLUERAY

HBT HBR2

HDMI

OUT

RS232 1

PROJ N

PROJECTOR

CONSOLE

HBT2

HBR2

HDMI HDBASET RECEIVER, FURNITURE MOUNT

RACK SHELF

EXTRON DTP3 R 201

EXTRON RSB 123 W/ RFF FACEPLATES

OFP

A/R

HBR2

HDMI HDBASET RECEIVER, FURNITURE MOUNT

RACK SHELF

EXTRON DTP3 T 202

EXTRON RSB 123 W/ RFF FACEPLATES

OFP

A/R

HBT2

ANTENNA DISTRIBUTION AMPLIFIER, 1X4 A/R SHURE UA845UWBANTD

VIDEO SWITCH, DIGITALINX, EXISTING 0 EXISTINGVS

NETWORK SWITCH, DANTE CAPABLE 1 NETGEAR AVLINENS

BLUERAY PLAYER, RACK MOUNTED, EXISTING 0 EXISTINGBLUERAY

AUDIO DSP, NETWORKED, W/

ALL NECESSARY LICENSES

OFP Q-SYS CORE 24FADSP

1 AV RISER

NO SCALE

GOD MIC

GENERAL CONFIGURATION NOTES

1. 'ADSP' AND CONTROL/LOGIC WIRING IS GENERIC. SEE MANUFACTURER'S INSTRUCTION SHEET FOR WIRING

DETAILS.

2. CONFIGURE NETWORK SWITCH TO SUPPORT ALL NECESSARY PROTOCOLS FOR AUDIO SWITCHING AND

CONTROL.

3. CONFIGURE 'ADSP' SO PUSHING BUTTON ON AUTO MODE BUTTON PANEL 'BP' ENABLES AND DISABLES AUTO MODE, AND BUTTON IS LIT, WHEN AUTO MODE IS ACTIVE. PROVIDE BUTTON DEBOUCE, AND 10 SEC TIME OUT

BETWEEN MODE CHANGES.

3.1. WHEN AUTO MODE IS ENGAGED, AUDIO INPUTS SHALL BE ROUTED DIRECTLY THROUGH 'ADSP', AND THEN

TO AMPLIFIERS.

3.2. WHEN AUTO MODE IS OFF, AUDIO INPUTS ARE CONVERTED TO DANTE STREAMS/CHANNELS, AND ROUTED TO CONSOLE. CONSOLE MIX IS ROUTED BACK TO 'ADSP' THROUGH DANTE STREAMS AND SENT TO

AMPLIFIERS.

3.3. PROVIDE ANY NECESSARY MIC LEVELS, SUCH THAT ALL INPUTS PROVIDE THE SAME OUTPUT LEVELS WHEN THE SAME SOURCE IS APPLIED. NO ADDITIONAL ROOM EQ IS REQUIRED. SYSTEM SPEAKERS HAVE BEEN

TUNED IN EXISTING AMPLIFIERS.

4. MAINTAIN PROJECTOR CONTROL VIA RS-232 FROM EXISTING VIDEO SWITCH (DIGITALINX ARK SYSTEM).

5. USE DEFAULT FACTORY NAMES FOR ALL Q-SYS PERIPHERAL DEVICES. ADJUST NAMES IN 'ADSP'

CONFIGURATION FILE TO MATCH FACTORY NAMES.

6. ALL CONFIGURATION FILES SHALL BE THE PROPERTY OF THE OWNER, AND SHALL BE DOCUMENTED AND

DELIVERED TO OWNER PRIOR TO PROJECT CLOSE OUT.

1. NO CHANGES SHALL BE MADE, WITH OUT PROJECT CONSULTANT AND OWNER'S WRITTEN CONSENT.

2. REFER TO DRAWINGS FOR EXACT NUMBER OF COMPONENTS REQUIRED IF NOT SPECIFIED IN EQUIPMENT

LIST.

3. FIRESEAL ALL CONDUITS AND PENETRATIONS THOUGH WALLS, FLOORS AND CEILINGS, INCLUDING AROUND

CONDUIT ENTRY AND EXIT POINTS.

4. LABEL ALL CABLES REGARDLESS OF LENGTH, SEE SPECIFICATIONS FOR LABELING REQUIREMENTS.

5. USE CADDY CLIPS OR BRIDAL RINGS TO SUPPORT ALL CABLES INSTALLED OUTSIDE OF CONDUIT, SEE CABLE

SPECIFICATIONS FOR ADDITIONAL DETAILS.

6. SITE PROJECT PHOTOS ARE AVAILIBLE FROM CONSULTANT UPON REQUEST. EMAIL

SPOULSEN@ENVISIONENG.COM

7. CONTRACTOR SHALL FILED VERIFY PROEJCTOR AND SCREEN LOCATIONS, AND EXISTING SCREEN SIZE TO

DETERMINE NECESSARY PROJECTOR LENS.

RECEIVER, TWISTED PAIR, W

POWER SUPPLY

RACK MOUNTING SYSTEM (PLATE)

RDL TX TPR3A

RDL PS-24AS

RDL TX-RA5

RXA

UI1

RACK 'A2'

RACK 'A1'

UI1

WIRELESS MIC RECEIVER, RACK MOUNTED, W/

BODYPACK RECEIVERS

HEADWORN MICROPHONE (TA4F CONNECT)

HANDHELD MICROPHONE

RECHARGEABLE BATTERIES

DUAL CHARGING TRAY

8 BATTERY CHARGER

SHURE QLXD4

SHURE QLXD1

SHURE MX153

SHURE QLXD2/SM58

SHURE SB900C

SHURE SB200

SHURE SBC800

WMR

ANTENNA, WIRELESS MIC A/R SHURE UA8WM

SPEAKER, CENTER FIRING, BI AMP 3 BLAZE AUDIO CCA10I

MOUNTING HARNESS

SUPPORT POLE, CUSTOM, BLACK

AR BLAZE AUDIO CCA10I-RIGGRID

SPEAKER, FOLD BACK 1 BLAZE AUDIO CBL528

MOUNTING HARNESS

SUPPORT POLE, CUSTOM, BLACK

AR CHIEF CMA 395

NPT POLE & CUSTOM OVERHEAD MOUNTING HARDWARE

SPEAKER, SIDE FILLS 2 BLAZE AUDIO CBL528

FLOWN, ABOVE CEILING, THROUGH GRILL CLOTH AR CUSTOM

SPEAKER, SUBWOOFER 2 BLAZE AUDIO BL118ISS

FLOWN, ABOVE CEILING, THROUGH GRILL CLOTH AR CUSTOM

AMP 1, 4 CH, 300 W/CHANNEL, 4 BLAZE AUDIO POWER ZONE CONNECT 3004

AMP 2, 125 W 1 CH, GREEN ROOM 1 BLAZE AUDIO POWER ZONE CONNECT 122D

WMR

ANTD

AMP 1

OUT 1

OUT 2

OUT 3

OUT 4

OUT 5

OUT 6

OUT 7

OUT 8

AMP 1

AMP 1 SUB

SUB

AMP 2

S E

AMP1

AMP2

SUB

ANTD

EA501

AUDIO VISUAL

SCHEDULES,

NOTES, DETAILS

AND DIAGRAMS

NO. DATE REVISIONS

1 2 3 4 5

CHECKED BY: DW

DRAWN BY: SP / SK

ENVISION PROJECT NO: 2025-247.01

DATE:

ISSUE:

04/01/2026

CONSTRUCTION DOCUMENTS

6 7

240 E. MORRIS AVE. SUITE 200

SALT LAKE CITY, UT 84115

P (801) 534-1130 F (801) 534-1080 www.envisioneng.com

Fil e N am e:

\25

\20

-2

.00

- A ud ito riu m Up gr ad es \01

_D wg s\E lk

Ri dg e M idd le\

1.d wg La st Pl ott ed

: 2

6/0 3/3

0 @ 6:

:20

P M

By : S

L D

L L

Sheets and Views

EG001-Layout1

EG101-Layout1

EG102-Layout1

ED101-Layout1

EL101-Layout1

EL501-Layout1

ET101-Layout1

ET501-Layout1

File details come from the government source that posted it. Updated Apr 3, 2026.