596A4-22-700 Drawings 07 - Electrical.pdf

ELECTRICAL EQUIPMENT

DISCONNECT SWITCHT

NOTE: THE ACTUAL SIZE OF EQUIPMENT IS SHOWN ON THE DRAWINGS AND MAY

DIFFER FROM WHAT IS SHOWN BELOW.

ELECTRICAL DISTRIBUTION EQUIPMENT

TYPE AS INDICATED ON DRAWINGS

TRANSFORMER

FUSED DISCONNECT

SWITCH

MOTOR STARTER

VFD MOTOR STARTER

SPD SURGE PROTECTION DEVICE

M ELECTRICAL METER

START/STOP,

MOMENTARY CONTACT

PUSHBUTTON SWITCH

NOTE 4,5

NOTE 1 NOTE 2

SINK OR

BASIN

FINISHED FLOOR

DEVICE MOUNTING NOTES:

1.

2.

3.

4.

COORDINATE ABOVE COUNTER ("AC") WIRING DEVICES WITH

CASEWORK, COUNTERS AND BACKSPLASH SUCH THAT THE

DEVICES AND RECEPTACLES ARE LOCATED AT +42" AFF OR 6"

ABOVE THE COUNTERTOP OR BACKSPLASH, WHICHEVER IS

HIGHER. WIRING DEVICES IDENTIFIED AS "HZ" SHALL BE

HORIZONTALLY-INSTALLED WITHIN THE BACKSPLASH OR

APPLICABLE MOUNTING MEDIUM AND VERTICALLY-CENTERED.

ALL RECEPTACLES INSTALLED WITHIN 6'-0" OF THE EDGE OF ANY

SINK OF BASIN SHALL HAVE GFI PROTECTION. DO NOT INSTALL

RECEPTACLES WITHIN 12" OF THE EDGE OF A SINK OR BASIN.

COORDINATE WITH THE TELECOMMUNICATIONS DRAWINGS TO

ENSURE THAT A RECEPTACLE IS INSTALLED WITHIN 18"

HORIZONTAL TO ALL SIGNAL AND DATA DEVICE LOCATIONS.

SWITCHES AND OTHER FLUSH WALL-MOUNTED DEVICES SHALL BE

MOUNTED WITHIN 24" OF DOORFRAME. COORDINATE WITH

ARCHITECTURAL DRAWINGS FOR DOORS WITH SIDELITES. WHERE

DEVICES ARE TO BE INSTALLED ON A WALL ADJACENT- AND

PERPENDICULAR- TO THE DOORFRAME, MOUNT THE DEVICE 12"

BEYOND THE DOOR SWING EXTENT. COORDINATE ROUGH-IN

LOCATIONS WITH DIV. 27 AND 28 DEVICES.

NOTE 3

NOTE 6

C L

SEE FIRE ALARM GENERAL NOTES

C L

S T

U

O N

TV

FCR AA

HZM

F

TYPICAL DEVICE MOUNTING HEIGHTS:

A

DSP

FZ

REF

MW

VM

IM

ABOVE COUNTER

SEE "DEVICE MOUNTING NOTES" NOTE 1

DISPOSAL, +24" AFF

FREEZER, +24" AFF

REFRIGERATOR, +24" AFF

MICROWAVE, +6" ABOVE MICROWAVE SHELF

VENDING MACHINE, +24" AFF

ICE MACHINE, +24" AFF

DEVICE BACKBOXES SHOWN

FOR REFERENCE ONLY

5.

6.

COORDINATE MOUNTING LOCATION WITH OTHER TRADES

TO ENSURE A COMMON MOUNTING HEIGHT, UNIFORM

SPACING AND AESTHETICALLY-PLEASING APPEARANCE.

WIRING DEVICES MOUNTING HEIGHT INDICATED IN LEGEND

AND ON THE DRAWINGS SHALL BE THE DISTANCE

MEASURED FROM THE CENTER OF THE DEVICE TO THE

FINISHED FLOOR.

TYPICAL WIRING DEVICE MOUNTING DETAIL (NOT TO SCALE)

1. THE FIRE ALARM CONTENT SHOWN ON THE DRAWINGS REPRESENTS A

SCHEMATIC LAYOUT WITH CERTAIN SPECIFIC REQUIREMENTS IDENTIFIED.

PROVIDE ENGINEERED SHOP DRAWINGS (SIGNED AND SEALED) AND FINAL

INSTALLATION IN COMPLIANCE WITH THESE FIRE ALARM GENERAL NOTES,

THE SCHEMATIC FIRE ALARM CONTENT AND REQUIREMENTS SET FORTH BY

THESE DRAWINGS, AND ANY ADDITIONAL REQUIREMENTS ESTABLISHED BY

CODE, THE AUTHORITIES HAVING JURISDICTION, OR UNFORESEEN

CONDITIONS. FURNISH THESE ENGINEERED FIRE ALARM SHOP DRAWINGS

TO BOTH THE AUTHORITIES HAVING JURISDICTION (AHJ) AND THE

ARCHITECT FOR REVIEW.

2. PROVIDE ENGINEERED FIRE ALARM SHOP DRAWINGS THAT INCLUDE ALL

DEVICES, EQUIPMENT, AND APPURTENANCES AS REQUIRED BY APPLICABLE

CODES OR AS NECESSARY TO FOR A COMPLETE, FUNCTIONAL, FIRE ALARM

SYSTEM INCLUDING INTERFACES WITH OTHER SYSTEMS AS DESCRIBED IN

THE CONSTRUCTION DOCUMENTS.

3. SPECIAL REQUIREMENTS FOR CIRCUIT BREAKERS PROVIDING

OVERCURRENT PROTECTION TO FIRE ALARM SYSTEM CLASS I CIRCUITS:

PROVIDE VISUALLY-DISTINGUISHABLE RED CIRCUIT BREAKERS WITH LOCK-

ON DEVICE AND 'FIRE ALARM SYSTEM' LABEL.

FIRE ALARM SYSTEM

FIRE ALARM

CONTROL PANEL

FIRE ALARM

ANNUNCIATOR PANEL

MANUAL PULL STATION

GENERATOR

ANNUNCIATOR PANEL

HORN

WALL-MOUNTED

HORN/STROBE

WALL-MOUNTED

STROBE

WALL-MOUNTED

HEAT DETECTOR

FIXED TEMPERATURE

HEAT DETECTOR

RATE OF RISE

SMOKE DETECTOR

PHOTOELECTRIC TYPE

FACP

SD

FIRE ALARM BELL

SPRINKLER FLOW SWITCH

SPRINKLER TAMPER SWITCH

SPRINKLER SOLENOID VALVE

PRESSURE SWITCH

DOOR HOLDER

EOL RESISTOR

CONTROL RELAY

ADDRESSABLE

MONITOR MODULE

ADDRESSABLE

SMOKE DAMPER

DUCT-MOUNTED

SMOKE DETECTOR

PHOTOELECTRIC TYPE;

CLEAN AGENT HEAD;

DATA CENTER SMOKE

DETECTOR

FAAP

GAP

F

F

F#

F#

HF

HR

B

FW

FT

FV

FP

DH

FR

FM

SD

DS

F

CA

S

PLAN MARK

EQUIPMENT NUMBER

SHEET NUMBER

LINE TYPE LEGEND

DRAWING REFERENCES

NEW WORK BY THIS CONTRACTOR

(DARK, SOLID LINE)

EXISTING TO REMAIN OR NEW WORK BY OTHERS

(LIGHT, SOLID LINE)

EXISTING TO BE REMOVED BY THIS CONTRACTOR

(DARK, DASHED LINE, DEMOLITION PLANS)

NORTH ARROW

PLAN DETAIL REFERENCE TITLE

KEYED NOTE DESIGNATION

PLAN MARK

EQUIPMENT NUMBER

EQUIPMENT DESIGNATION REFER TO MEP

SCHEDULE FOR CIRCUITING AND DEVICE

REQUIREMENTS AND FLOOR PLANS FOR

LOCATIONS

ENLARGED PLAN REFERENCE

PLAN MARK

SHEET NUMBER

A101

SIM

AHU

TITLE

SCALE

PLAN

NORTH

TRUE

NORTH

MATCHLINE

1 REVISION TAG

EQUIPMENT

TAG

1. REFER TO THE MEP COORDINATION SCHEDULE SHOWN ON

E6.11 FOR MECHANICAL EQUIPMENT AND PLUMBING

EQUIPMENT REQUIREMENTS. EQUIPMENT TYPE

EQUIPMENT NUMBER

SAMPLE

EQUIPMENT

MEP COORDINATION

AHU

RACEWAYS

CABLE TRAY : TYPE AS NOTED

LADDER TRAY

WIRE IN CONDUIT, CONCEALED

WIRE IN CONDUIT, EXPOSED

CONTINUATION

HANDHOLE MANHOLEHH MH

JUNCTION AND PULL BOXES

PULL BOX

SHADING INDICATES EMERGENCY POWER

JUNCTION BOX : CEILING OR FLOOR MOUNTED. SIZE

PER N.E.C. REQUIREMENTS.

JUNCTION BOX : WALL MOUNTED. SIZE PER N.E.C.

REQUIREMENTS.J

J

P

WIRING DEVICES

RECEPTACLES (NEMA 5-20 R) - UNLESS OTHERWISE INDICATED,

ALL RECEPTACLES ARE TO BE UL LISTED AS HOSPITAL GRADE

RECESSED SIMPLEX GFI RECESSED DUPLEX

RECESSED DUPLEX RECESSED QUAD

OVERHEAD CEILING RECEPTACLE

REFER TO ELECTRICAL NEW WORK PLANS

FOR NEMA CONFIGURATION

RECESSED JBOX

TELEVISION RECEPTACLE

PROVIDE COMPARTMENTALIZED BACKBOX WITH

DUPLEX RECEPTACLE WITHIN ONE OF THE ISOLATED

COMPARTMENTS

DUPLEX CEILING RECEPTACLE

FLUSH-MOUNT WITHIN CEILING. REFER TO

TELECOMMUNICATIONS NEW WORK PLANS FOR

SIGNAL REQUIREMENTS

FLOORBOX

QUAD RECEPTACLE / SIGNAL MULTI-SERVICE FLOORBOX.

REFER TO TELECOMMUNICATIONS NEW WORK PLANS

FOR SIGNAL REQUIREMENTS

OVERHEAD JUNCTION BOX

ELECTRICAL CONNECTION

TV

J

J

E

A AMPERES

AC ALTERNATING CURRENT

ACS ACCESS CONTROL SYSTEM

AIC AMPERES INTERRUPTING CAPACITY

AV AUDIO/VIDEO

AWG AMERICAN WIRE GAUGE

BAS BUILDING AUTOMATION SYSTEM

C CONDUIT

CAT CATEGORY

CATV CABLE TELEVISION

CCTV CLOSED CIRCUIT TELEVISION

CFCI CONTRACTOR FURNISHED, CONTRACTOR INSTALLED

CPP COPPER HORIZONTAL PATCH PANEL

CT CABLE TRAY

CU COPPER

CUH CABINET UNIT HEATER

CO COPIER

CP EMERGENCY CRITICAL POWER

DC DIRECT CURRENT

DEMO REMOVE AS INDICATED

DPST DUAL POLE, SINGLE THROW

DW DISHWASHER

EC EMPTY CONDUIT

EF EXHAUST FAN

EGC EQUIPMENT GROUNDING CONDUCTOR

EIA ELECTRONICS INDUSTRIES ASSOCIATIONS

EMT ELECTRICAL METALLIC TUBING

EOC EMERGENCY OPERATIONS CENTER

EP EMERGENCY POWER

EPO EMERGENCY POWER OFF

ETR EXISTING TO REMAIN

EWC ELECTRIC WATER COOLER

FAAP FIRE ALARM ANNUNCIATOR PANEL

FACP FIRE ALARM CONTROL PANEL

FBO FURNISHED BY OTHERS

FO FIBER OPTIC

FPD FLAT PANEL DISPLAY

FPP FIBER OPTIC PATCH PANEL

FT FEET OR FOOT

GFI OR GFCI GROUND FAULT CIRCUIT INTERRUPTER

GC GENERAL CONTRACTOR

G OR GND GROUND

GFR GROUND FAULT RELAY

GFP GROUND FAULT PROTECTION

HZ HERTZ

IG ISOLATED GROUND

INV INVERTER

JBOX JUNCTION BOX

K KILO

KCMIL THOUSAND CIRCULAR MILS

KVA KILOVOLT AMPERES

KWH KILOWATT HOURS

LC LIGHTING CONTACTOR

LPI LIGHTNING PROTECTION INSTITUTE

MAX MAXIMUM

MCB MAIN CIRCUIT BREAKER

MDP MAIN DISTRIBUTION PANEL

MH MANHOLE

MLO MAIN LUGS ONLY

MM MULTIMODE

MTD MOUNTED

MW MICROWAVE

N NEUTRAL CONDUCTOR

N.C. NORMALLY CLOSED

NEC NATIONAL ELECTRICAL CODE

NEMA NATIONAL ELECTRICAL MANUFACTURES

ASSOCIATION

NP NORMAL POWER

MA MANUFACTURER'S ASSOCIATION

NIC NOT IN CONTRACT

NL NIGHT LIGHT

N.O. NORMALLY OPEN

NTS NOT TO SCALE

OC ON CENTER

OFCI OWNER FURNISHED, CONTRACTOR INSTALLED

OFOI OWNER FURNISHED,OWNER INSTALLED

ONT OPTICAL NETWORK TERMINAL

P POLE

PR PAIR

PVC POLYVINYL CHLORIDE

R RELAY

REF REFRIGERATOR

RGS RIGID GALVANIZED STEEL CONDUIT

RN REPLACE WITH NEW

RMC RIGID METAL CONDUIT

SCCR SHORT CIRCUIT CURRENT RATING

SCH SCHEDULE

ShTP SHIELDED TWISTED PAIR

SE SECURITY ELECTRONICS

SM SINGLE MODE

SPD SURGE PROTECTION DEVICE

SPECS CONTRACT SPECIFICATIONS

SPST SINGLE POLE SINGLE THROW

STR STRAND

SWBD SWITCHBOARD

T TRANSFORMER

TC TELECOMMUNICATIONS POWER CRITICAL

TN TELECOMMUNICATIONS POWER NORMAL

TR TELECOMMUNICATIONS ROOM

TYP TYPICAL

UHF ULTRA-HIGH FREQUENCY

UL UNDERWRITERS' LABORATORIES

UON UNLESS OTHERWISE NOTED

UPS UNINTERRUPTIBLE POWER SUPPLY

UTP UNSHIELDED TWISTED PAIR

V VOLTS

VA VOLT AMPERES

VFD VARIABLE FREQUENCY DRIVE

VHF VERY HIGH FREQUENCY

VM VENDING MACHINE

W WIRE OR WATT

WP WEATHERPROOF

WR WEATHER-RESISTANT

WPIU WEATHERPROOF WHILE IN USE

XFMR TRANSFORMER

XRL EXISTING TO BE RELOCATED

Z IMPEDANCE

ABBREVIATIONS

HALF-SHADING:

LIFE SAFETY POWER

NO SHADING:

NORMAL POWER

LIGHTING FIXTURES

1. "NL" INDICATES UNSWITCHED LUMINAIRE

2. NOTE THAT THE SIZE AND SHAPE OF FIXTURES AND ASSOCIATED HALF-

SHADING VARY BY FIXTURE TYPE

3. PROVIDE UNSWITCHED HOT CONDUCTOR TO FIXTURES WITH BATTERY

BACK UP, ONBOARD UL 924. REFER TO UL 924 DETAILS FOR ADDITIONAL

REQUIREMENTS.

HALF-SHADING:

CRITICAL POWER

A 1c

UPPER CASE LETTER - FIXTURE MARK

LOWER CASE LETTER - FIXTURE SWITCH LEG

NUMBER - FIXTURE CIRCUIT NUMBER

INDUSTRIAL PENDANT

LED LIGHTING, VARIOUS

LENGTHS

LINE VOLTAGE LIGHTING CONTROLS

AREA CONTROL SCHEME TAG

REFER TO LIGHTING CONTROL SCHEDULE

OCCUPANCY DETECTOR

ASTRONOMICAL TIMER SWITCH

CEILING DUAL TECHNOLOGY OCCUPANCY DETECTION

LIGHTING SENSOR

DIMMER

DT

OD

X

LC0

ROOM NAME

LC#

ROOM TAG

CONTROL SCHEME TAG

SUBSCRIPT LEGEND:

3 : 3-WAY SWITCH

4 : 4-WAY SWITCH

P : PILOT LIGHT SWITCH

C : MOMENTARY CONTACT SWITCH

a, b, ... : LOWERCASE SUBSCRIPT INDICATES SWITCH LEG

OD : WALL OCCUPANCY DETECTION

OR : OVER-RIDE SWITCH

LV : LOW VOLTAGE SWITCH

TOGGLE SWITCH

OD

1. WHERE TWO OR MORE SWITCHES ARE SHOWN ADJACENT TO EACH

OTHER, PROVIDE A COMMON GANG BOX WITH A SINGLE, SEAMLESS

FACEPLATE.

2. PROVIDE NEUTRAL AND UNSWITCHED HOT TO LINE VOLTAGE CONTROL

DEVICE WHEN REQUIRED.

3. SEE LIGHT FIXTURE CONTROL SCHEDULE FOR UL 924 AND UL 1008

REQUIREMENTS. SEE UL 924 AND UL 1008 DETAIL.

LS

D

ELECTRICAL DEMOLITION NOTES

1. REMOVE, CAP AND RELOCATE EQUIPMENT, OUTLETS, CONDUIT, WIRE, ETC.,

AS SHOWN AND SPECIFIED ON DRAWINGS, AND AS MAY BECOME NECESSARY

BECAUSE OF EXISTING FIELD CONDITIONS. VISIBLY EXAMINE ALL EXISTING

WALLS DESIGNATED FOR REMOVAL TO DETERMINE THE CONDUIT AND THE

WIRING THAT WILL REQUIRE CAPPING AND REMOVAL, WHETHER OR NOT

SUCH CONDITIONS ARE INDICATED ON THE DRAWINGS. FAILURE TO VISIT THE

SITE AND TO TAKE ALL EXISTING CONDITIONS INTO ACCOUNT WILL NOT

ALLOW FOR CHANGES TO THE SCOPE OF WORK.

2. MAINTAIN CIRCUIT CONTINUITY TO ALL EXISTING FIXTURES, EQUIPMENT,

OUTLETS, ETC., TO REMAIN IN USE WHETHER NOTED ON THE PLANS OR NOT.

FIELD VERIFY EXISTING ITEMS TO REMAIN IN USE. RECONNECT RACEWAYS

AND WIRING FOR EXISTING CIRCUITS WHICH MUST BE RE-ROUTED OR WHICH

ARE PARTIALLY ABANDONED TO POWER THE REMAINING OUTLETS ON THE

CIRCUIT.

3. REMOVE ALL UNUSED WIRING AND CABLES BACK TO THEIR SOURCE.

REMOVE ALL UNUSED CONDUIT THAT IS EXPOSED OR ABOVE ACCESSIBLE

CEILINGS WHICH IS AFFECTED BY OR IS IN THE AREA OF THE DEMOLITION

WORK.

4. THE INTENTION OF THE ELECTRICAL DEMOLITION DRAWINGS IS TO

DISCONNECT AND REMOVE ALL ELECTRICAL WORK MADE VOID BY THE SCOPE

OF THE CONSTRUCTION AND ALTERATION. FIELD VERIFY EXACT MATERIAL

QUANTITIES REQUIRED TO BE REMOVED.

5. DISCONNECT AND REMOVE ALL EXISTING ELECTRICAL EQUIPMENT, DEVICES,

ASSOCIATED RACEWAYS, SUPPORTING HARDWARE, AND WIRING, WHICH

HAVE BEEN MADE OBSOLETE BY THE WORK OR IS SHOWN DASHED ON THE

ELECTRICAL DEMOLITION DRAWINGS, UNLESS OTHERWISE NOTED.

ALTHOUGH AN ATTEMPT HAS BEEN MADE TO INDICATE ALL OF THIS WORK,

TOTAL ACCURACY IS NOT GUARANTEED. VISIBLY EXAMINE ALL AREAS AND

WALLS AND CEILINGS SCHEDULED FOR REMOVAL TO DETERMINE EXISTING

ELECTRICAL ITEMS TO REMAIN.

6. WHERE THE REMOVAL OF ELECTRICAL EQUIPMENT, CONDUIT, BOXES, AND

SUPPORTING HARDWARE REQUIRES WALL PATCHING AND REFINISHING,

REFER TO ARCHITECTURAL FRONT-END SPECIFICATIONS FOR PATCH AND

FINISH WORK.

7. WHERE BURIED CONDUITS EXTENDING OUT OF A CONCRETE SLAB BECOME

ABANDONED, CUT AND GRIND THE CONDUITS OFF FLUSH WITH TOP OF SLAB

AND PLUG WITH NON-SHRINK WATERPROOF GROUT FILL.

8. TAKE ALL REMOVED MATERIALS FROM THE PROJECT SITE, EXCEPT FOR

THOSE TO BE RELOCATED, STORED, OR TURNED OVER TO THE OWNER.

9. ACCEPTANCE OF CONTRACT MEANS INSTALLER ACCEPTS EXISTING

CONDITIONS.

10. COORDINATE ALL DEMOLITION WORK WITH ALL OTHER TRADES.

11. PROVIDE A BLANK COVER OVER THE OUTLET WHERE A FLUSH DEVICE IS

BEING REMOVED FROM FLOORS AND WALLS THAT ARE TO REMAIN. MATCH

THE COLOR AND MATERIAL TO THE EXISTING REMAINING COVERS IN THE

ROOM OR SPACE.

12. WHEN HAVING TO DISPOSE OF HAZARDOUS MATERIALS INCLUDING REMOVAL

OF FLUORESCENT LIGHT FIXTURES WHERE BALLASTS CONTAIN PCBS AND

LAMPS CONTAIN MERCURY, REFER TO ARCHITECTURAL FRONT-END

SPECIFICATIONS FOR HAZARDOUS MATERIAL DISPOSAL GUIDELINES, AND

COMPLY WITH ALL FEDERAL, STATE, AND LOCAL LAWS.

13. MODIFY EXISTING PANEL DIRECTORIES (OR REPLACE) FOR PANELBOARDS

WHICH HAVE HAD ALTERATIONS TO THE CIRCUITS ORIGINATING THEREIN.

DESCRIBE THE LOAD AND LOCATION. TYPE, DO NOT HAND LETTER NEW

PANELBOARD DIRECTORIES.

ELECTRICAL GENERAL NOTES

1. MAKE ALL INSTALLATIONS IN ACCORDANCE WITH THE ARCHITECTURAL

BARRIERS ACT (ABA).

2. MOUNTING HEIGHTS INDICATED WITHIN PLANS AND SCHEDULES ARE

DIMENSIONED TO THE CENTER LINE OF THE DEVICE, EQUIPMENT,

LUMINAIRE, ETC. UNLESS OTHERWISE NOTED.

3. COORDINATE EXACT EQUIPMENT LOCATIONS WITH OTHER TRADES.

EQUIPMENT LOCATIONS SHOWN ON ELECTRICAL PLANS ARE

DIAGRAMMATICAL ONLY AND MIGHT NOT BE EXACT.

4. CIRCUIT IDENTIFICATION NUMBERS BESIDE ELECTRICAL DEVICES AND

CONNECTION POINTS ON PLANS CORRESPOND TO AN OVERCURRENT

DEVICE IN THE DESIGNATED PANELBOARD. NOTE ALL CIRCUIT NUMBER

CHANGES MADE IN THE FIELD AT EACH ELECTRICAL DEVICE AND

CONNECTION POINT. ALSO CORRECT THE DIRECTORIES AND DEVICE

MARKINGS AT PANELBOARDS, SWITCHBOARDS AND SWITCHGEAR TO

ACCURATELY REFLECT THE AS-BUILT CONDITIONS.

5. INSTALL EMERGENCY AND EXIT LUMINAIRE WIRING IN A SEPARATE

RACEWAY FROM THAT OF ANY NORMAL POWER DEVICE.

6. CONCEAL ALL CONDUIT IN WALLS, PARTITIONS, ABOVE CEILINGS, AND IN

FLOOR SLABS, ETC. UNLESS OTHERWISE INDICATED ON THE PLANS OR IN

THE SPECIFICATIONS. CONDUIT ROUTED IN MECHANICAL ROOMS,

ELECTRICAL ROOMS, AND STORAGE ROOMS WITHOUT CEILINGS MAY BE

ROUTED EXPOSED.

7. COORDINATE VERTICAL CONDUIT ROUTING TO WALL MOUNTED DEVICES

TO ENSURE DEVICES LOCATED WITHIN AN 18-INCH HORIZONTAL

DIMENSION WILL BE CENTER-ALIGNED VERTICALLY.

8. FIELD COORDINATE ALL ELECTRICAL AND TELECOMMUNICATIONS

EQUIPMENT MOUNTING LOCATIONS TO AVOID ENCROACHMENT OF

OPERATION AND ACCESS TO EQUIPMENT FROM OTHER TRADES.

COORDINATE THE APPROPRIATE MOUNTING LOCATION WITH THE

AFFECTED DISCIPLINES WHEN EQUIPMENT IS SPECIFIED TO BE MOUNTED

ONTO THE SURFACE OF ANOTHER DISCIPLINE'S EQUIPMENT.

9. REPAIR ALL OPENINGS MADE IN EXISTING WALLS, PARTITIONS, ETC TO

ACCOMMODATE WORK OF THIS DISCIPLINE TO MATCH THE SURROUNDING

CONDITIONS, USING WORKERS QUALIFIED IN THE APPROPRIATE TRADE.

APPROPRIATELY GROUT OR SEAL ALL CONDUITS THROUGH WALLS.

10. ALL MATERIALS USED TO SEAL PENETRATIONS OF FIRE RATED WALLS

AND FLOORS MUST HAVE BEEN TESTED AND CERTIFIED AS A SYSTEM PER

ASTM E814 STANDARDS FOR FIRE TESTS OF THROUGH-PENETRATION

FIRESTOPS.

11. PERFORM ALL WELDING ACCORDING TO AMERICAN WELDING SOCIETY

STANDARDS. FURNISH CERTIFICATES QUALIFYING EACH WELDER TO THE

ARCHITECT OR ENGINEER PRIOR TO START OF WORK. THE ARCHITECT

OR ENGINEER RESERVES THE RIGHT TO REQUIRE QUALIFYING

DEMONSTRATION, AT NO ADDITIONAL EXPENSE, OF ANY WELDERS

ASSIGNED TO THE JOB.

12. REPLACE OR REINSTALL ALL PORTIONS OF THE BUILDING (CEILING TILES,

WALLS, ETC) REMOVED TO ACCOMMODATE THE INSTALLATION OF ANY

ELECTRICAL DEVICE, EQUIPMENT, ETC., USING WORKERS QUALIFIED IN

THE APPROPRIATE TRADE.

13. COORDINATE LUMINAIRE LOCATIONS SUCH THAT LUMINAIRES RUN

PARALLEL TO THE FACE OF THE EQUIPMENT AND OVER AISLES BETWEEN

EQUIPMENT IN ALL MECHANICAL AND ELECTRICAL EQUIPMENT AREAS.

INSTALL AT PROPER LOCATIONS AND HEIGHTS TO PROPERLY ILLUMINATE

ALL GAGES, PANELS, ELECTRICAL EQUIPMENT, CONTROLS, VALVES, ETC.

CHAIN HANGING, STEM HANGING, CHANNEL HANGING, ETC. ARE

ACCEPTABLE METHODS.

14. PROVIDE FIRE RATED AND WEATHER SEALANT AS REQUIRED TO SEAL

PENETRATIONS.

15. UNLESS OTHERWISE NOTED, CONTRACTOR SHALL ROUTE NEW CONDUIT

AS HIGH AS POSSIBLE IN CEILING SPACES. COORDINATE ROUTING WITH

EXISTING SYSTEMS AND OWNER.

ELECTRICAL PHASING NOTES

1. PRIOR TO STARTING CONSTRUCTION OF NEW TELECOM ROOM (TR)

ROOMS AND DATA CENTER WORK, CONTRACTOR WILL PARTICIPATE IN

PHASING MEETINGS WITH OWNER AND CONTRACTORS OF OTHER

DISCIPLINES TO DISCUSS MEANS AND METHODS FOR PHASING THE

INSTALLATION OF NEW IT EQUIPMENT AND THE REMOVAL OF OLD

EQUIPMENT AFTER NEW EQUIPMENT IS RUNNING, VERIFIED, AND

CIRCUITS CUT OVER. IT IS IMPORTANT THAT NEW IT EQUIPMENT BE

INSTALLED AND TESTED PRIOR TO REMOVING OLD EQUIPMENT.

2. FOR NEW TELECOM ROOMS (TR’S) AND DATA CENTER, NEW DATA RACKS

WILL BE CONSTRUCTED, POWERED, AND DATA CIRCUITS CUT OVER

PRIOR TO REMOVAL OF EXISTING IT RACKS. NOTE THAT EXISTING AND

NEW RACKS WILL HAVE TO BOTH BE POWERED AT THE SAME TIME FOR

CONSTRUCTION PHASING.

3. FOR DATA CENTER SPACE, EXISTING CONDUITS IN CEILING AND UNDER

FLOOR THAT ARE IDENTIFIED TO BE RELOCATED, VERIFY WHETHER

CONDUITS CONTAIN ACTIVE CIRCUITS AND WHAT LOADS THESE CIRCUITS

FEED. ACTIVE CIRCUITS MUST BE RE-ROUTED AND CUT-OVER TO NEW

PANELS AS REQUIRED. ALL CIRCUITS IDENTIFIED AS ABANDONED OR

UNUSED WILL BE REMOVED TO FREE UP SPACE IN CEILING AND UNDER

FLOOR.

4. POWER OUTAGES WILL BE REQUESTED AND DISCUSSED A MINIMUM OF 4

WEEKS PRIOR TO SCHEDULING THE OUTAGE. EACH OUTAGE AND

METHOD OF PROCEDURE WILL BE DISCUSSED IN DETAIL WITH THE

OWNER AND ALL INVOLVED CONTRACTORS PRIOR TO OUTAGE.

CONTRACTOR SHALL VERIFY WHAT EQUIPMENT OR CIRCUITS WILL BE

IMPACTED IN ORDER THAT ALL PERTINENT STAFF CAN BE NOTIFIED IN

TIMELY MANNER. VERIFY OWNER’S OUTAGE TIMEFRAME CONSTRAINTS

WHEN SCHEDULING OUTAGES.

5. MOST KEY WORK REQUIRING OUTAGES, CUT-OVERS, ETC. WILL BE

PERFORMED DURING PREMIUM TIME, (NIGHTS OR WEEKENDS), WITHIN

DESIGNATED ALLOWABLE TIME-FRAME DICTATED BY THE OWNER.

6. FOR EXISTING ACTIVE CIRCUITS THAT NEED TO BE CUT-OVER TO NEW

PANEL, ENSURE THAT CIRCUITS ARE CUT-OVER PRIOR TO REMOVING OLD

PANEL. EC SHALL VERIFY ALL EXISTING ACTIVE CIRCUITS THAT REQUIRE

NEW FEED.

7. COORDINATE ALL ELECTRICAL WORK AFFECTING IT RACKS IN TR ROOMS

AND DATA CENTER CLOSELY WITH OWNER, CONSTRUCTION MANAGER,

AND CONTRACTORS OF OTHER DISCIPLINES.

CARD READER WITH PIN PAD WALL MOUNT AT +48" A.F.F.

SECURITY ALARM SYSTEMS

ACCESS CONTROL SYSTEMS

SECURITY CAMERA

PUSHBUTTON : +48" A.F.F. OR AS NOTED

KEYSWITCH : WALL MOUNT AT +48" A.F.F.

CARD READER : WALL MOUNT AT +48" A.F.F.

POWER SUPPLYPS

CR

CRP

KS

CAM 360 DEGREE SECURITY CAMERA

REX REQUEST TO EXIT

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

1 & 1A

E-000

BKM

ELECTRICAL SYMBOLS AND ABBREVIATIONS

BKM5/16/23

D007 C121 C222

RISERS

RISERS

WALL BEING REMOVED WALL BEING REMOVED

1. FOR EXISTING TR ROOM WALLS SCHEDULED FOR DEMO,

CONTRACTOR SHALL REMOVE ALL DEVICES AS REQUIRED

FOR WALL DEMO. THIS WORK SHALL BE PHASED KEEPING

EXISTING SYSTEMS POWERED AND ACTIVE UNTIL NEW

SYSTEMS ARE UP AND RUNNING. COORDINATE WORK

WITH CONSTRUCTION MANAGER AND OWNER.

2. CONDUIT RISER LOCATIONS SHOWN ARE APPROXIMATE.

KEEP EMERGENCY CRITICAL POWER CONDUITS GROUPED

SEPARATE FROM NORMAL POWER CONDUITS WITH 6-

INCH SEPARATION MINIMUM. PROVIDE OFFSETS /

CONDUIT BENDS AND PULL BOXES TO ROUTE AROUND

OBSTACLES AS REQUIRED. KEEP CONDUITS AS TIGHT TO

WALL AS POSSIBLE. ENSURE THAT CONDUITS DO NOT

COVER UP OR PREVENT ACCESS TO ACTIVE SYSTEMS.

CONFIRM EXACT CONDUIT ROUTING WITH CONSTRUCTION

MANAGER AND OWNER. SEE ENLARGED TR ROOM PLANS

FOR LOCATION OF NEW / RELOCATED DEVICES.

PICTURE REFERENCE GEN NOTES

RISER LOCATION

RISER

LOCATION

RISER LOCATION

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

1A

E-010

BKM

BUILDING 1A PICTURE REFERENCES PAGE 1

BKM5/16/23

1B

2B

1C 3C 5C

2C

4C

3B

4B

NEW PANELS

NEW PANELS

NOT TO SCALE

LEFT WALL

NOT TO SCALE

RIGHT WALL

NOT TO SCALE

DEMO RIGHT

1B

NOT TO SCALE

DEMO MIDDLE

2B

NOT TO SCALE

DEMO LEFT

3B

NOT TO SCALE

WAITING ROOM EXPANSION

4B

NOT TO SCALE

E-10 PIC 7 BACK LEFT DEMO LOW

1C

NOT TO SCALE

E-10 PIC 8 EXPANSION AREA FRONT

2C

NOT TO SCALE

E-10 PIC 9 BACK LEFT DEMO HIGH

3C

NOT TO SCALE

E-10 PIC 10 EXPANSION AREA BACK

4C

NOT TO SCALE

RISER RIGHT WALL, BACK WALL DEMO

5C

13'-5 7/8"

TECH

CLOSET

C580

C333 CU411 C580

RISER

RISERSRISERS

WALLS BEING REMOVED

WALLS BEING REMOVED

RISERS

WALLS BEING REMOVED

1. FOR EXISTING TR ROOM WALLS SCHEDULED FOR DEMO,

CONTRACTOR SHALL REMOVE ALL DEVICES AS REQUIRED

FOR WALL DEMO. THIS WORK SHALL BE PHASED KEEPING

EXISTING SYSTEMS POWERED AND ACTIVE UNTIL NEW

SYSTEMS ARE UP AND RUNNING. COORDINATE WORK

WITH CONSTRUCTION MANAGER AND OWNER.

2. CONDUIT RISER LOCATIONS SHOWN ARE APPROXIMATE.

KEEP EMERGENCY CRITICAL POWER CONDUITS GROUPED

SEPARATE FROM NORMAL POWER CONDUITS WITH 6-

INCH SEPARATION MINIMUM. PROVIDE OFFSETS /

CONDUIT BENDS AND PULL BOXES TO ROUTE AROUND

OBSTACLES AS REQUIRED. KEEP CONDUITS AS TIGHT TO

WALL AS POSSIBLE. ENSURE THAT CONDUITS DO NOT

COVER UP OR PREVENT ACCESS TO ACTIVE SYSTEMS.

CONFIRM EXACT CONDUIT ROUTING WITH CONSTRUCTION

MANAGER AND OWNER. SEE ENLARGED TR ROOM PLANS

FOR LOCATION OF NEW / RELOCATED DEVICES.

PICTURE REFERENCE GEN NOTES

RISER LOCATION

RISER LOCATION

RISER LOCATION

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

1A

E-011

BKM

BUILDING 1A PICTURE REFERENCES PAGE 2

BKM5/16/23

1B

4B

6B 2B

5B

7B

3B 1C 2C

3C

NOT TO SCALE

BACK LEFT DEMO

NOT TO SCALE

RISER LOCATION

NOT TO SCALE

BACK RIGHT DEMO

NOT TO SCALE

EXPANSION

NOT TO SCALE

BACK WALL DEMO HIGH

NOT TO SCALE

LAB EXPANSION 1

1B

NOT TO SCALE

BACK RIGHT DEMO

2B

NOT TO SCALE

LEFT WALL DEMO

3B

NOT TO SCALE

LAB EXPANSION 2

4B

NOT TO SCALE

RISER LOCATION

5B

NOT TO SCALE

BACK LEFT WALL DEMO

6B

NOT TO SCALE

BACK WALL DEMO HIGH

7B

NOT TO SCALE

FRONT WALL DEMO

C1

NOT TO SCALE

RIGHT WALL DEMO

C2

NOT TO SCALE

OUTSIDE WALLS DEMO

C3

FF:VCT

A002C A104 A243

A345

RISER

1. FOR EXISTING TR ROOM WALLS SCHEDULED FOR DEMO,

CONTRACTOR SHALL REMOVE ALL DEVICES AS REQUIRED

FOR WALL DEMO. THIS WORK SHALL BE PHASED KEEPING

EXISTING SYSTEMS POWERED AND ACTIVE UNTIL NEW

SYSTEMS ARE UP AND RUNNING. COORDINATE WORK

WITH CONSTRUCTION MANAGER AND OWNER.

2. CONDUIT RISER LOCATIONS SHOWN ARE APPROXIMATE.

KEEP EMERGENCY CRITICAL POWER CONDUITS GROUPED

SEPARATE FROM NORMAL POWER CONDUITS WITH 6-

INCH SEPARATION MINIMUM. PROVIDE OFFSETS /

CONDUIT BENDS AND PULL BOXES TO ROUTE AROUND

OBSTACLES AS REQUIRED. KEEP CONDUITS AS TIGHT TO

WALL AS POSSIBLE. ENSURE THAT CONDUITS DO NOT

COVER UP OR PREVENT ACCESS TO ACTIVE SYSTEMS.

CONFIRM EXACT CONDUIT ROUTING WITH CONSTRUCTION

MANAGER AND OWNER. SEE ENLARGED TR ROOM PLANS

FOR LOCATION OF NEW / RELOCATED DEVICES.

PICTURE REFERENCE GEN NOTES

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

E-012

BKM

BUILDING 1 PICTURE REFERENCES PAGE 1

BKM5/16/23

1B

RISERS

WALL BEING

REMOVED

RISERS

RISERS

RISERS

RISERS

WALL BEING

REMOVED

RISERS

WALL BEING

REMOVED

RISER

RISER

RISER

RISER

RISER

RISER

NOT TO SCALE

LOCKER ROOM EXPANSION

NOT TO SCALE

RISER 1

NOT TO SCALE

RISER 2

NOT TO SCALE

RIGHT WALL DEMO

NOT TO SCALE

BACK LEFT WALL

1B

NOT TO SCALE

CABLE STORAGE

2B

NOT TO SCALE

RISER LOCATION

3B

2B 3B

NOT TO SCALE

DEMO LEFT LOW

1C

NOT TO SCALE

DEMO LEFT HIGH

2C

NOT TO SCALE

LEFT HIGH CABLES

3C

NOT TO SCALE

EXPANSION AREA

4C

1C 2C

3C

4C

NOT TO SCALE

HIGH BACK WALL

1D

NOT TO SCALE

LEFT WALL DEMO

2D

NOT TO SCALE

LOW BACK WALL

3D

1D 3D

2D

10'-8"

RESTROOM

A580A

DATA/TELE.

AU547

A450 AU547 A627

RISERS

WALL BEING

REMOVED

RISERS WALL BEING

REMOVED

RISERS WALL BEING

REMOVED

RISER

1. FOR EXISTING TR ROOM WALLS SCHEDULED FOR DEMO,

CONTRACTOR SHALL REMOVE ALL DEVICES AS REQUIRED

FOR WALL DEMO. THIS WORK SHALL BE PHASED KEEPING

EXISTING SYSTEMS POWERED AND ACTIVE UNTIL NEW

SYSTEMS ARE UP AND RUNNING. COORDINATE WORK

WITH CONSTRUCTION MANAGER AND OWNER.

2. CONDUIT RISER LOCATIONS SHOWN ARE APPROXIMATE.

KEEP EMERGENCY CRITICAL POWER CONDUITS GROUPED

SEPARATE FROM NORMAL POWER CONDUITS WITH 6-

INCH SEPARATION MINIMUM. PROVIDE OFFSETS /

CONDUIT BENDS AND PULL BOXES TO ROUTE AROUND

OBSTACLES AS REQUIRED. KEEP CONDUITS AS TIGHT TO

WALL AS POSSIBLE. ENSURE THAT CONDUITS DO NOT

COVER UP OR PREVENT ACCESS TO ACTIVE SYSTEMS.

CONFIRM EXACT CONDUIT ROUTING WITH CONSTRUCTION

MANAGER AND OWNER. SEE ENLARGED TR ROOM PLANS

FOR LOCATION OF NEW / RELOCATED DEVICES.

PICTURE REFERENCE GEN NOTES

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

E-013

BKM

BUILDING 1 PICTURE REFERENCES PAGE 2

BKM5/16/23

12 3

RISER

RISER

MOVE EXISTING SECURITY

AND OTHER EQUIPMENT FOR

RISER PLACEMENT

RISER

RISER

DEMO

RISER

NOT TO SCALE

BACK LEFT WALL

NOT TO SCALE

DEMO BACK LEFT

NOT TO SCALE

BACK WALL MIDDLE VIEW

NOT TO SCALE

DEMO LEFT WALL

1B

NOT TO SCALE

RISER TOP

2B

NOT TO SCALE

RISER BOTTOM

3B

1B

2B3B

NOT TO SCALE

DEMO LEFT WALL HIGH

NOT TO SCALE

DEMO LEFT WALL

NOT TO SCALE

DEMO PACU PILLAR

NOT TO SCALE

PACU OVERALL VIEW

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

E-014

BKM

POWER SOURCE AND UPS FEEDERS PICTURE

REFERNCES

BKM5/16/23

ADD BREAKERS

ADD NEW

BREAKER

ADD NEW

BREAKER

UTILIZE

SPARE

BREAKER

NOT TO SCALE

BUILDING 1A UNIT SUB - NORMAL POWER SOURCE

NOT TO SCALE

BUILDING 1 - NORMAL POWER SOURCE, SBB

NOT TO SCALE

UPS FEEDERS FROM A056 ELEC ROOM TO CRAWL SPACE (TOP VIEW)

NOT TO SCALE

BUILDING 1A GENERATOR SWITCHBOARD

NOT TO SCALE

BUILDING 1A - EMERGENCY POWER SOURCE, SBC

NOT TO SCALE

UPS FEEDERS FROM A056 ELEC ROOM RO CRAWL SPACE (BOTTOM VIEW)

NEW

RISERS

RISER LOCATION

RISERS

PULL BOX

TO A056

ELEC ROOM

TO DATA CENTER

ROUTE CONDUITS

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

E-015

BKM

CRAWL SPACE AND OTHER PICTURE

REFERENCES

BKM5/16/23

A002C RISER FROM BELOW

NOT TO SCALE

CRAWL SPACE TUNNEL TO A056 ELECTRICAL ROOM

NOT TO SCALE

CRAWL SPACE - ELEVAATOR P1, P2, P3 (DOOR SIDE)

NOT TO SCALE

CRAWL SPACE - BUILDING 1 CONDUIT RISER ORIGIN POINT - SOUTHWEST CORNER OF ELEV P3

NOT TO SCALE

CONDUIT PENETRATION FROM ABOVE CRAWL

SPACE

5A

NOT TO SCALE

CRAWL SPACE TUNNEL CONDUITS ENTERING DATA CENTER

NOT TO SCALE

CRAWL SPACE- ELECTRICAL PULL BOX UNDER AC UNIT IN ELEC A022

NOT TO SCALE

PARKING GARAGE - BLDG. 1A CONDUIT RISER ORIGIN POINT - NORTHWEST CORNER OF ELEV P4 matt.steineman Snapshot

1 2

NEW RISERS

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

E-016

BKM

MECH ROOM, CRAWL SPACE ACCESS, AND BLDG

1A PARKING GARAGE CEILING PICTURE

REFERENCES

BKM5/16/23

NOT TO SCALE

BUILDING 1 - MECHANICAL ROOM 2 (ACCESS TO CRAWL SPACE)

NOT TO SCALE

BUILDING 1 - MECHANICAL ROOM

ELECTRICAL KEYED NOTES

1. PROVIDE FLOOR-MOUNT UNISTRUT FRAME AND

HARDWARE NECESSARY FOR SECURE MOUNTING OF

NORMAL AND CRITICAL DISTRIBUTION PANELS. LINE-UP

WITH EXISTING MCC; ENSURE THERE IS SUFFICIENT

CLEARANCES FOR EXISTING EQUIPMENT.

2. PROVIDE NEW NORMAL AND CRITICAL POWER

DISTRIBUTION PANELS. SEE POWER PLAN SHEET E102.

3. PROVIDE NORMAL AND CRITICAL POWER FEEDERS ALONG

WALL NEAR FLOOR, THROUGH THIS MECHANICAL ROOM,

AND INTO CRAWL SPACE. SEE POWER PLAN SHEET E102.

4. EXISTING CRAWL SPACE ACCESS HATCH IN MECHANICAL

ROOM 2.

NOT TO SCALE

PARKING GARAGE RISER BACK VIEW

NOT TO SCALE

PARKING GARAGE RISER SIDE VIEW

NOT TO SCALE

PARKING GARAGE RISER FRONT VIEW

EMERGENCY

POWER

PA06B

NORMAL

POWER

PA06A

TR

D007D

MECH RM

D-B038

EMERGENCY

GENERATOR

D003

TRANSFORMERS &

SWITCHGEAR

D003A

CORRIDOR

DH001

STAIR

PAS06

STAIR

PAS07

ELECTRICAL

D001

TD

D002

CORRIDOR

DH002

MECH RM

D004

EMS

D005

STOR

D005A

STORAGE

D006

ELEVATOR

S6

ELEVATOR

S7

C O

R R

ID

O

R D

H

PAINT

SHOP

D007C

CORRIDOR

DH003

SIGNAL

CLOSET

D008

STORAGE

PA08

PARKING

LEVEL A

PA01

CORRIDOR

DH004

CARPENTER

SHOP

D007

STORAGE

AREA

PA06

CHIEF

D007A

LOCKSMITH

D007B

CORRIDOR

DH005

CHIEF

ELECTRICIAN

B014B

M&O

FORMAN

B013

CORRIDOR

BH002

STAIR

PAS08

M E

C H

A N

IC

A

L B

F

UP

UP DN

UP

KEY PLAN

PA

D

B

A

E-400B-1A.G

E-400A-1A.G

E-400C-1A.G

GARAGE DOOR

145 6

PLAN

NORTH

TRUE

NORTH

1. CABLE TRAY - SEE TECHNOLOGY DRAWINGS FOR CABLE TRAY

ROUTES. EC SHALL COORDINATE WITH TECHNOLOGY

CONTRACTOR AND PROVIDE ELECTRICAL WORK IN BASE BID

TO FACILITATE THE INSTALLATION OF CABLE TRAY WORK

INCLUDING: DISCONNECTING POWER AND THE REMOVAL OF

LIGHT FIXTURES AND ELECTRICAL DEVICES IN CEILING, AND

THE RE-ROUTING OF BRANCH CIRCUIT CONDUIT (TO MAKE

ROOM FOR CABLE TRAY). REINSTALL ELECTRICAL DEVICES

AND LIGHT FIXTURES IN CEILING AFTER CABLE TRAY AND

DATA CABLING WORK IS COMPLETE. COORDINATE REQUIRED

ELECTRICAL WORK WITH CONSTRUCTION MANAGER, VA STAFF

AND CABLE TRAY AND DATA CABLING CONTRACTORS.

2. ASBESTOS & HAZARDOUS MATERIAL - WHEN ELECTRICAL

WORK REQUIRES REMOVING CEILING TILES AND WORKING IN

CEILING SPACE, IT IS POSSIBLE TO ENCOUNTER ASBESTOS

AND DEAL WITH HAZARDOUS MATERIAL. REFER TO

ARCHITECTURAL FRONT-END SPECIFICATIONS FOR PROPER

PROCEDURES IN DEALING WITH ASBESTOS AND OTHER

HAZARDOUS MATERIALS. IT IS THE ELECTRICAL

CONTRACTOR'S RESPONSIBILITY TO ALERT THE

CONSTRUCTION MANAGER AND APPROPRIATE VA STAFF IF

THERE IS A POSSIBILITY THAT HAZARDOUS MATERIAL IS

PRESENT IN CEILING WORK SPACE.

3. CORE DRILLING - COORDINATE REQUIRED CORE DRILLING

WORK IN WALLS AND FLOORS WITH VA STAFF AND

CONSTRUCTION MANAGER. ALL NOISY WORK SHALL BE

PERFORMED DURING PREMIUM TIME. REFER TO

ARCHITECTURAL FRONT-END SPECIFICATIONS FOR FURTHER

DETAIL ON PROPER PROCURES FOR CORE-DRILLING AND

NOISY WORK.

4. ALL CONDUIT ROUTES SHOWN ARE DIAGRAMMATIC IN

MATURE. EC SHALL COORDINATE ACTUAL ROUTE AROUND

EXISTING SYSTEMS, PROVIDING BENDS, OFFSETS, PULL

BOXES, EXPANSION JOINTS, AND PROPER SUPPORTS AS

REQUIRED. ROUTE CONDUIT AS HIGH AS POSSIBLE IN CEILING

SPACES AND IN CRAWL SPACE. COORDINATE ROUTES WITH VA

MAINTENANCE TO ENSURE CONDUIT ROUTE IS NOT HINDERING

ACCESSIBILITY AND MAINTAINABILITY TO EXISTING SYSTEMS.

FOR CONDUIT RISERS, PROVIDE STRAIN-RELIEF CABLE RISER

GRIPS TO SUPPORT CONDUCTORS IN RISER CONDUIT AT NO

MORE THAN 100 FOOT INTERVALS PER NEC TABLE 300.19.

KEY ELECTRICAL COORDINATION

GENERAL NOTES

BUILDING 1A GROUND CABLE / 480V

FEEDER LIST

1. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO

NEW ELECTRICAL ROOM PA06A GROUND BAR.

2. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO TR

ROOM D007D GROUND BAR.

3. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO

BUILDING 1A TR ROOMS GROUND RISER.

4. 480V EMERGENCY FEEDER FOR ATS E-POWER FEED (E-POWER

TR RISER) FROM GENERATOR SWITCHBOARD IN BUILDING 1A

GENERATOR ROOM TO ATS-1A-EC IN ELECTRICAL ROOM

PA06B.

5. 480V NORMAL FEEDER FOR ATS N-POWER FEED (E-POWER TR

RISER) FROM BLDG 1A UNIT SUBSTATION DISTRIBUTION (T5

SIDE) TO ATS-1A-EC IN ELECTRICAL ROOM PA06B.

6. 480V NORMAL FEEDER FOR N-POWER TR RISER FROM BLDG 1A

UNIT SUBSTATION DISTRIBUTION (T6 SIDE) TO HNDP-1A IN

ELECTRICAL ROOM PA06A

X

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

1A

E-100-1A.G

BKM

OVERALL GROUND FLOOR PLAN - AREAS D & PA -

ELECTRICAL

BKM5/16/23

1/8" = 1'-0"

OVERALL GROUND FLOOR PLAN - AREAS D & PA - ELECTRICAL

ELECTRICAL KEYED NOTES

1. FROM NEW ELECTRICAL ROOMS, ROUTE MULTIPLE 208/120V TR

ROOM PANEL FEEDERS THROUGH PARKING GARAGE CEILING

TO DESIGNATED RISER LOCATION. REMOVE CEILING TILES AS

NEEDED TO FACILITATE FEEDER INSTALLATION. COORDINATE

WITH OWNER REGARDING METHOD AND PHASING OF

REMOVAL AND REINSTALLATION OF CEILING TILES. ROUTE

CONDUITS AS HIGH AS POSSIBLE SECURED TO STRUCTURE

OVERHEAD. PROVIDE OFFSETS AS NEEDED TO ROUTE ABOVE

EXISTING SYSTEMS. PROVIDE HANGERS AND PULL BOXES AS

REQUIRED. COORDINATE EXACT ROUTE WITH OWNER. SEE

ONE-LINE FOR FURTHER DETAIL.

2. PROVIDE GROUND BUS BAR IN MAIN ELECTRICAL ROOM AS

INDICATED. USE COMPRESSION 2-HOLE LUGS FOR

TERMINATING GROUND CABLES. EXPOSED GROUND SHALL BE

RUN IN PVC CONDUIT, SUPPORT AT 5-FOOT INTERVALS. FOR

GROUND CABLES ROUTED ABOVE PARKING GARAGE CEILING,

PROVIDE PVC CONDUIT RISERS ON WALL SURFACE TO ALLOW

GROUND CABLES TO PENETRATE THROUGH WALL INTO

PARKING GARAGE CEILING SPACE. SEE GROUNDING DETAIL.

3. DIVISION 27 WORK, SEE TECHNOLOGY DRAWINGS FOR

FURTHER DETAILS. PROVIDE GROUND CONDUCTOR FROM

MAIN BUILDING 1A GROUND BAR TO FIRST FLOOR

TELECOMMUNICATION ROOM (TR) SBB GROUND BAR. SEE

GROUNDING DETAIL.

4. ELECTRICAL ROOM GROUND BUS BAR. SEE GROUNDING

DETAIL SHEET. PROVIDE PVC RISERS ON WALL SURFACE FOR

GROUND CABLE PENETRATION ABOVE PARKING GARAGE

CEILING.

5. PROVIDE TRIAD GROUND SYSTEM: (3) NEW 10-FOOT 3/4-INCH

COPPER-CLAD GROUND RODS INSTALLED 10 FEET APART

MINIMUM. ALL CONNECTIONS SHALL BE EXOTHERMIC CAD-

WELD TYPE. LOCATION SHALL BE IN TRIANGULAR GRASS AREA.

COORDINATE WITH OWNER AND OTHER UNDERGROUND

UTILITIES ON-SITE.

TO BUILDING 1A TR ROOM RISERS

(SEE SHEET E101-1A)

SEAL WALL AT GROUND

PENETRATION BELOW GRADE

TRENCH AND BACKFILL.

IF HARD SURFACE, CUT

AND PATCH

MOTOR

CYCLE PARKING

WHEEL

CHAIR PARKING

UP

UP DN

UP

DN

DN

EP

NP

E-400A-1A.G

E-400B-1A.G

BUILDING 1 DATA

CENTER A073

BUILDING 1 NEW

ELECTRICAL ROOMS

A022A & A022B

BUILDING 1

GENERATOR

ROOM B037

BUILDING 1 MAIN

ELECTRICAL

ROOM B037A

E-403B-1.G

E-403E-1.G

E-403A-1.G

CONDUITS ENTER

CRAWL SPACE HERE

E-403G-1.G

E-403H-1.G

E-403C-1.G

AC REFRIGERATION

EQUIP ROOM B038

SVC ROOM

B039

ELECTRICAL

DISTRIBUTION

ROOM B037B

TR B046A

ELECTRICAL

ROOM A056

TR A002C

UPS-A

UPS-B

3 4 5 6

145 6

CRAWL SPACE

BOUNDARY

PLAN

NORTH

TRUE

NORTH

1. CABLE TRAY - SEE TECHNOLOGY DRAWINGS FOR CABLE TRAY

ROUTES. EC SHALL COORDINATE WITH TECHNOLOGY

CONTRACTOR AND PROVIDE ELECTRICAL WORK IN BASE BID

TO FACILITATE THE INSTALLATION OF CABLE TRAY WORK

INCLUDING: DISCONNECTING POWER AND THE REMOVAL OF

LIGHT FIXTURES AND ELECTRICAL DEVICES IN CEILING, AND

THE RE-ROUTING OF BRANCH CIRCUIT CONDUIT (TO MAKE

ROOM FOR CABLE TRAY). REINSTALL ELECTRICAL DEVICES

AND LIGHT FIXTURES IN CEILING AFTER CABLE TRAY AND

DATA CABLING WORK IS COMPLETE. COORDINATE REQUIRED

ELECTRICAL WORK WITH CONSTRUCTION MANAGER, VA STAFF

AND CABLE TRAY AND DATA CABLING CONTRACTORS.

2. ASBESTOS & HAZARDOUS MATERIAL - WHEN ELECTRICAL

WORK REQUIRES REMOVING CEILING TILES AND WORKING IN

CEILING SPACE, IT IS POSSIBLE TO ENCOUNTER ASBESTOS

AND DEAL WITH HAZARDOUS MATERIAL. REFER TO

ARCHITECTURAL FRONT-END SPECIFICATIONS FOR PROPER

PROCEDURES IN DEALING WITH ASBESTOS AND OTHER

HAZARDOUS MATERIALS. IT IS THE ELECTRICAL

CONTRACTOR'S RESPONSIBILITY TO ALERT THE

CONSTRUCTION MANAGER AND APPROPRIATE VA STAFF IF

THERE IS A POSSIBILITY THAT HAZARDOUS MATERIAL IS

PRESENT IN CEILING WORK SPACE.

3. CORE DRILLING - COORDINATE REQUIRED CORE DRILLING

WORK IN WALLS AND FLOORS WITH VA STAFF AND

CONSTRUCTION MANAGER. ALL NOISY WORK SHALL BE

PERFORMED DURING PREMIUM TIME. REFER TO

ARCHITECTURAL FRONT-END SPECIFICATIONS FOR FURTHER

DETAIL ON PROPER PROCURES FOR CORE-DRILLING AND

NOISY WORK.

4. ALL CONDUIT ROUTES SHOWN ARE DIAGRAMMATIC IN

MATURE. EC SHALL COORDINATE ACTUAL ROUTE AROUND

EXISTING SYSTEMS, PROVIDING BENDS, OFFSETS, PULL

BOXES, EXPANSION JOINTS, AND PROPER SUPPORTS AS

REQUIRED. ROUTE CONDUIT AS HIGH AS POSSIBLE IN CEILING

SPACES AND IN CRAWL SPACE. COORDINATE ROUTES WITH VA

MAINTENANCE TO ENSURE CONDUIT ROUTE IS NOT HINDERING

ACCESSIBILITY AND MAINTAINABILITY TO EXISTING SYSTEMS.

FOR CONDUIT RISERS, PROVIDE STRAIN-RELIEF CABLE RISER

GRIPS TO SUPPORT CONDUCTORS IN RISER CONDUIT AT NO

MORE THAN 100 FOOT INTERVALS PER NEC TABLE 300.19.

KEY ELECTRICAL COORDINATION

GENERAL NOTES

BUILDING 1 GROUND CABLE / 480V

FEEDER LIST

1. GREEN INSULATED COPPER STRANDED GROUND CABLE

FROM NEW GROUND BAR IN MAIN ELECTRICAL ROOM B037A

TO DATA CENTER GROUND BAR.

2. GREEN INSULATED COPPER STRANDED GROUND CABLE

FROM NEW GROUND BAR IN MAIN ELECTRICAL ROOM B037A

TO NEW ELECTRICAL ROOM A022A GROUND BAR.

3. 480V CRITICAL FEEDER FOR UPS-A POWER, FROM HCDP1-

EHRM IN MECH ROOM B038 TO UPS-A.

4. 480V CRITICAL FEEDER FOR UPS-A BYPASS POWER, FROM

HCDP1-EHRM IN MECH ROOM B038 TO UPS-A.

5. 480V NORMAL FEEDER FOR UPS-B POWER, FROM HNDP1-

EHRM IN MECH ROOM B038 TO UPS-B.

6. 480V NORMAL FEEDER FOR UPS-B BYPASS POWER, FROM

HNDP1-EHRM IN MECH ROOM B038 TO UPS-B.

7. 480V CRITICAL FEEDER FOR TR POWER, FROM HCDP1-EHRM

IN MECH ROOM B038 TO T-1-EC IN ELECTRICAL ROOM A022B.

8. 480V NORMAL FEEDER FOR TR POWER, FROM HNDP1-EHRM IN

MECH ROOM B038 TO T-1-NP IN ELECTRICAL ROOM A022A.

X

BUILDING 1A GROUND CABLE / 480V

FEEDER LIST

1. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO

NEW ELECTRICAL ROOM PA06A GROUND BAR.

2. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO TR

ROOM D007D GROUND BAR.

3. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO

BUILDING 1A TR ROOMS GROUND RISER.

4. 480V EMERGENCY FEEDER FOR ATS E-POWER FEED (E-POWER

TR RISER) FROM GENERATOR SWITCHBOARD IN BUILDING 1A

GENERATOR ROOM TO ATS-1A-EC IN ELECTRICAL ROOM

PA06B.

5. 480V NORMAL FEEDER FOR ATS N-POWER FEED (E-POWER TR

RISER) FROM BLDG 1A UNIT SUBSTATION DISTRIBUTION (T5

SIDE) TO ATS-1A-EC IN ELECTRICAL ROOM PA06B.

6. 480V NORMAL FEEDER FOR N-POWER TR RISER FROM BLDG 1A

UNIT SUBSTATION DISTRIBUTION (T6 SIDE) TO HNDP-1A IN

ELECTRICAL ROOM PA06A

X

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

1 & 1A

E-100

BKM

OVERALL GROUND FLOOR REFERENCE PLAN -

ELECTRICAL

BKM5/16/23

1" = 20'-0"

ELECTRICAL GROUND FLOOR REFERENCE PLAN

BUILDING 1A MAIN

ELECTRICAL ROOM D003A

BUILDING 1A GENERATOR

ROOM D003A

BUILDING 1A NEW

ELECTRICAL ROOMS

PA06A & PA06B

BUILDING 1A BUILDING 1

CRAWL SPACE

BELOW GROUND

FLOORBUILDING 1A TR

RISER LOCATION

BUILDING 1 TR

RISER LOCATION

MOTOR

CYCLE PARKING

WHEEL

CHAIR PARKING

PARKING

LEVEL A

PA01

STAIRWELL

PAS05

ELEVATOR

PAE04

ELEVATOR

PAE05

ELEVATOR

LOBBY

PA02

STORAGE

PA07

OTHER

SPACE

PAM03

C O

R R

ID

O

R B

H

STORAGE

A008

FOOD

STORAGE

A006A

STAIRWELL

PAS04

FROM NDP-1A FROM ECDP-1AFROM D003A

GROUND BAR

EX. SPRINKLER LINES BELOW

EX. DATA CONDUITS

EX. DATA RISERS

EX. DATA 6" CABLE TRAY

NEW TR RISERS

1. CABLE TRAY - SEE TECHNOLOGY DRAWINGS FOR CABLE TRAY

ROUTES. EC SHALL COORDINATE WITH TECHNOLOGY

CONTRACTOR AND PROVIDE ELECTRICAL WORK IN BASE BID

TO FACILITATE THE INSTALLATION OF CABLE TRAY WORK

INCLUDING: DISCONNECTING POWER AND THE REMOVAL OF

LIGHT FIXTURES AND ELECTRICAL DEVICES IN CEILING, AND

THE RE-ROUTING OF BRANCH CIRCUIT CONDUIT (TO MAKE

ROOM FOR CABLE TRAY). REINSTALL ELECTRICAL DEVICES

AND LIGHT FIXTURES IN CEILING AFTER CABLE TRAY AND

DATA CABLING WORK IS COMPLETE. COORDINATE REQUIRED

ELECTRICAL WORK WITH CONSTRUCTION MANAGER, VA STAFF

AND CABLE TRAY AND DATA CABLING CONTRACTORS.

2. ASBESTOS & HAZARDOUS MATERIAL - WHEN ELECTRICAL

WORK REQUIRES REMOVING CEILING TILES AND WORKING IN

CEILING SPACE, IT IS POSSIBLE TO ENCOUNTER ASBESTOS

AND DEAL WITH HAZARDOUS MATERIAL. REFER TO

ARCHITECTURAL FRONT-END SPECIFICATIONS FOR PROPER

PROCEDURES IN DEALING WITH ASBESTOS AND OTHER

HAZARDOUS MATERIALS. IT IS THE ELECTRICAL

CONTRACTOR'S RESPONSIBILITY TO ALERT THE

CONSTRUCTION MANAGER AND APPROPRIATE VA STAFF IF

THERE IS A POSSIBILITY THAT HAZARDOUS MATERIAL IS

PRESENT IN CEILING WORK SPACE.

3. CORE DRILLING - COORDINATE REQUIRED CORE DRILLING

WORK IN WALLS AND FLOORS WITH VA STAFF AND

CONSTRUCTION MANAGER. ALL NOISY WORK SHALL BE

PERFORMED DURING PREMIUM TIME. REFER TO

ARCHITECTURAL FRONT-END SPECIFICATIONS FOR FURTHER

DETAIL ON PROPER PROCURES FOR CORE-DRILLING AND

NOISY WORK.

4. ALL CONDUIT ROUTES SHOWN ARE DIAGRAMMATIC IN

MATURE. EC SHALL COORDINATE ACTUAL ROUTE AROUND

EXISTING SYSTEMS, PROVIDING BENDS, OFFSETS, PULL

BOXES, EXPANSION JOINTS, AND PROPER SUPPORTS AS

REQUIRED. ROUTE CONDUIT AS HIGH AS POSSIBLE IN CEILING

SPACES AND IN CRAWL SPACE. COORDINATE ROUTES WITH VA

MAINTENANCE TO ENSURE CONDUIT ROUTE IS NOT HINDERING

ACCESSIBILITY AND MAINTAINABILITY TO EXISTING SYSTEMS.

FOR CONDUIT RISERS, PROVIDE STRAIN-RELIEF CABLE RISER

GRIPS TO SUPPORT CONDUCTORS IN RISER CONDUIT AT NO

MORE THAN 100 FOOT INTERVALS PER NEC TABLE 300.19.

KEY ELECTRICAL COORDINATION

GENERAL NOTES

BUILDING 1A GROUND CABLE / 480V

FEEDER LIST

1. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO

NEW ELECTRICAL ROOM PA06A GROUND BAR.

2. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO TR

ROOM D007D GROUND BAR.

3. GREEN INSULATED COPPER STANDARD GROUND CABLE FROM

NEW GROUND BAR IN BLDG 1A MAIN ELECTRICAL ROOM TO

BUILDING 1A TR ROOMS GROUND RISER.

4. 480V EMERGENCY FEEDER FOR ATS E-POWER FEED (E-POWER

TR RISER) FROM GENERATOR SWITCHBOARD IN BUILDING 1A

GENERATOR ROOM TO ATS-1A-EC IN ELECTRICAL ROOM

PA06B.

5. 480V NORMAL FEEDER FOR ATS N-POWER FEED (E-POWER TR

RISER) FROM BLDG 1A UNIT SUBSTATION DISTRIBUTION (T5

SIDE) TO ATS-1A-EC IN ELECTRICAL ROOM PA06B.

6. 480V NORMAL FEEDER FOR N-POWER TR RISER FROM BLDG 1A

UNIT SUBSTATION DISTRIBUTION (T6 SIDE) TO HNDP-1A IN

ELECTRICAL ROOM PA06A

X

Project Number

Building Number

Drawing Number

DrawnCheckedIssue Date

Location

Project TitlePhaseDrawing Title

Approved: Project Director

ARCHITECT OF RECORDCONSULTANT

Revisions: Date:

U.S. Department of Veterans Affairs

Construction and Facilities Management

8718 Botts Lane Phone: (210) 816-4784

San Antonio, Texas 78217 Fax: (210) 881-6808 www.hfscompany.com jbianco@hfscompany.com

FULLY SPRINKLERED

569A4-22-700100% CONSTRUCTION

DOCUMENTS

LEXINGTON-COOPER EHRM

INFRASTRUCTURE DESIGN

1101 VETERANS DRIVE

LEXINGTON, KY 40502

21 3 4 5 6 7 8 9 10

21 3 4 5 6 7 8 9 10

B

A

C

D

E

F

B

A

C

D

E

F

St. Louis

6 South Old Orchard St. Louis, MO 63119 t: +1 800.404.7677 e: hello@introba.com www.introba.com

1A

E-101-1A.G

BKM

OVERALL GROUND FLOOR PLAN - AREA PA -

ELECTRICAL

BKM5/16/23

PLAN

NORTH

TRUE

NORTH

KEY PLAN

PA

D

B

A

1/8" = 1'-0"

OVERALL GROUND FLOOR PLAN - AREA PA - ELECTRICAL

ELECTRICAL KEYED NOTES

1. FROM NEW ELECTRICAL ROOMS, ROUTE MULTIPLE 208/120V TR

ROOM PANEL FEEDERS THROUGH PARKING GARAGE CEILING

(ABOVE CEILING TILES AND INSULATION) TO DESIGNATED

RISER LOCATION. COORDINATE WITH OWNER REGARDING

METHOD AND PHASING OF REMOVAL AND REINSTALLATION OF

CEILING TILES. ROUTE CONDUITS AS HIGH AS POSSIBLE

SECURED TO STRUCTURE OVERHEAD. PROVIDE OFFSETS AS

NEEDED TO ROUTE ABOVE EXISTING SYSTEMS. PROVIDE

HANGERS AND PULL BOXES AS REQUIRED. COORDINATE

EXACT ROUTE WITH OWNER. SEE ONE-LINE FOR FURTHER

DETAIL.

2. REMOVE AND PUT BACK CEILING TILES IN PARKING GARAGE.

ROUTE AROUND EXISTING SYSTEMS IN CEILING AS REQUIRED

TO ROUTE CONDUITS RISERS ABOVE CEILING. COORDINATE

WITH OWNER.

3. DIVISION 27 WORK, SEE TECHNOLOGY DRAWINGS FOR

FURTHER DETAILS. PROVIDE GREEN INSULATED STRANDED

COPPER GROUND CONDUCTOR FROM MAIN BLDG 1A GROUND

BAR TO FIRST FLOOR TELECOMMUNICATION ROOM (TR) SBB

GROUND BAR AS INDICATED FOR TELECOMMUNICATIONS

GROUND. SEE GROUNDING DETAIL.

4. SEE PICTURE 3 ON SHEET E-016.

5. SEE PICTURE 4 ON SHEET E-016.

6. SEE PICTURE 5 ON SHEET E-016.

TR

B046A

CORRIDOR

DH005

CHIEF

ELECTRICIAN

B014B

M&O

FORMAN

B013

ELECTRONIC

B014

ELECTRIC

SHOP

B014C

STAFF

TOILET

B015A

OFFICE

B017

STORAGE

FLAMMABLE

B016

STORAGE

GENERAL

B020

WAREHOUSE

B015

MAIL RM

B015B

EMS

EQUIP

B021

SOILED

UTILITY

B022A

OFFICE

B022D

OFFICE

B022E

C O

R R

ID

O

R B

H

TOILET

FEMALE

B019

TOILET

MALE

B018

MENS

TOILET

B003

HALL

B004

STORAGE

B009A

SOILED RECEIVING

DECONTAMINATION

AREA

B005

LOGISTICS

BREAKDOWN

B006B

HALL

B006A

ELEC.

B009

ELECTRIC

CLOSET

BU002

CORRIDOR

BH003

UNION

OFFICE

B011A

LOGISTICS

STORAGE

B011

OFFICE

B012A

PROSTHETICS

STORAGE

B015C

MORGUE

B015A

CORRIDOR

BH002

STAIR

PAS08

M E

C H

A N

IC

A

L B

F

AC

PLUMBING

MACH

B012

C O

R R

ID

O

R B

H

BULK

STORAGE

B010

CORRIDOR

OX101

STERILE AND

NON-STERILE

STORAGE

A001A

PREPARATION

STERILIZATION

WORK RM

A005C

GAS CYL

STORAGE

B005D

CLEAN

RECEIVING

B007

CORRIDOR

AH003

STORAGE

A008

RETAIL

STORE

A009

C O

R R

ID

O

R A

H

LOGISTICS SVC

INVENTORY

MGMT

B022

WOMENS

TOILET

B002

CORRIDOR

BH004

OFFICE

B022C

OFFICE

B022B

OFFICE

B022A

C O

R R

ID

O

R B

H

EMERGENCY

GENERATOR

RM B037

C O

R R

ID

O

R B

H

FEMALE

TOILET

B040

MENS

TOILET

B041

EMS

B036C

LINEN B036D

CANTEEN

STORAGE

B036B

MAIN

KITCHEN

B036

ENVIRONMENTAL

MGMT SUPPLY

B045D

SURGICAL

PACK

B045C

STORAGE

B045B

MAIN

KITCHEN

B036

OFFICE

SUPVS

B036F

DAIRY

& EGG

REFRIG

B036G

STORAGE

B035A

OFFICE

B035

STORAGE

& ISSUE

B034

STAIRWELL

BS003

EMS

B005A

MANUAL

CART WASH

B005B

EQUIP

STORAGE

AREA

B001

ELECTRIC

CLOSET

BU003

EMS

A001B

DUMB

ELEVATOR

CORRIDOR

BH006

SUPV

OFFICE

B045

BREAK

RM

B045A

STORAGE

A033

PM&RS

CHIEF'S

OFFICE

A032A

SECY

OFFICE

A032B

RESIDENTS

OFFICE

A032C

HALL

A032

CONFERENCE

RM

A032D

CHARTING

A032E

IT

B046

HAS

B044

TOILET

B044A

EMS

B043

ELECTRIC

CLOSET

B043A

EMS

CHECK IN

B042B

EMS

OFFICE

B042A

HAS

B044B

HAS

B044C

SVC

RM

B039

SECY/

RECEPTIONIST

B-042

OFFICE ASST

CHIEF WORK

RM

B-042C

CORRIDOR

BH004

ELECTRICAL

DISTRIBUTION

RM

B037B

A/C

REFRIGERATION

EQUIP RM

B038

TRANSFORMER

RM

B037A

UP

DN

DN

E-403A-1.G

E-403H-1.G

SEAL WALL AT GROUND CABLE

PENETRATION BELOW GRADE

1 2

3 4 7

5 6 8

ROUTE HIGH

ROUTE UNDER STAIRS

ROUTE LOW

ON WALL

ROUTE THROUGH

WALL INTO CRAWL

SPACE

1. CABLE TRAY - SEE TECHNOLOGY DRAWINGS FOR CABLE TRAY

ROUTES. EC SHALL COORDINATE WITH TECHNOLOGY

CONTRACTOR AND PROVIDE ELECTRICAL WORK IN BASE BID

TO FACILITATE THE INSTALLATION OF CABLE TRAY WORK

INCLUDING: DISCONNECTING POWER AND THE REMOVAL OF

LIGHT FIXTURES AND ELECTRICAL DEVICES IN CEILING, AND

THE RE-ROUTING OF BRANCH CIRCUIT CONDUIT (TO MAKE

ROOM FOR CABLE TRAY). REINSTALL ELECTRICAL DEVICES

AND LIGHT FIXTURES IN CEILING AFTER CABLE TRAY AND

DATA CABLING WORK IS COMPLETE. COORDINATE REQUIRED

ELECTRICAL WORK WITH CONSTRUCTION MANAGER, VA STAFF

AND CABLE TRAY AND DATA CABLING CONTRACTORS.

2. ASBESTOS & HAZARDOUS MATERIAL - WHEN ELECTRICAL

WORK REQUIRES REMOVING CEILING TILES AND WORKING IN

CEILING SPACE, IT IS POSSIBLE TO ENCOUNTER ASBESTOS

AND DEAL WITH HAZARDOUS MATERIAL. REFER TO

ARCHITECTURAL FRONT-END SPECIFICATIONS FOR PROPER

PROCEDURES IN DEALING WITH ASBESTOS AND OTHER

HAZARDOUS MATERIALS. IT IS THE ELECTRICAL

CONTRACTOR'S RESPONSIBILITY TO ALERT THE

CONSTRUCTION MANAGER AND APPROPRIATE VA STAFF IF

THERE IS A POSSIBILITY THAT HAZARDOUS MATERIAL IS

PRESENT IN CEILING WORK SPACE.

3. CORE DRILLING - COORDINATE REQUIRED CORE DRILLING

WORK IN WALLS AND FLOORS WITH VA STAFF AND

CONSTRUCTION MANAGER. ALL NOISY WORK SHALL BE

PERFORMED DURING PREMIUM TIME. REFER TO

ARCHITECTURAL FRONT-END…