5._25RS0030_Addendum_01_05.08.26.pdf
PDF 34 MB Posted
- Attached to
- 25RS0030 - REDDING SERVER ROOM HVAC MINISPLIT
- Solicitation number
- 0000039339
About this file
This Addendum #1 document, issued by the California Department of Veterans Affairs (CalVet) Procurement & Contract Management Unit on May 8, 2026, modifies the Invitation for Bid (IFB) 25RS0030 for a Redding Server Room HVAC Minisplit project located at 3400 Knighton Road, Redding, California 96002. The project involves the installation of a new backup split system cooling unit—specifically a Mitsubishi 3-ton heat pump with a wall-mounted fan coil unit—in Server (MDF) Room G14 at the CalVet Redding Residential Facility. The new split system unit will be integrated into the existing Building Management System (BMS) and will operate as a backup when the existing fan coil unit serving the MDF room becomes inoperable. This addendum replaces the original bid set dated March 17, 2026 with updated construction drawings dated April 24, 2026, including modifications to architectural, mechanical, and electrical drawing sheets, specifications, and a revised list of drawings.
The addendum details specific deletions and replacements of construction documents and drawing sheets, including updates to mechanical details (addition of Detail 7 Pipe Through Roof Detail), electrical enlarged floor plans, electrical roof plans, and electrical details. All new mechanical equipment must be UL-listed and properly labeled, with manufacturer cut sheets and specifications provided. The contractor is responsible for compliance with applicable national, state, and local codes including the California Mechanical Code (CMC), California Fire Code, Title 24, ASHRAE standards, and OSHA requirements. The refrigerant piping system must use R-454B or R-32 refrigerant, comply with ASME B31.5 and ASHRAE 15 standards, and be pressure-tested and leak-tested according to specifications. The new split system is required to include a PROCON BACnet and Modbus interface for integration with the existing BMS, a disconnect switch, and 1-inch deflection spring isolators, with a recommended 35-amp fuse/breaker size for the outdoor unit.
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
- 1 - Project Number: CA25-0394
STATE OF CALIFORNIA GAVIN NEWSOM. Governor
DEPARTMENT OF VETERANS AFFAIRS
Procurement & Contract Management Unit 1227
“O” Street, Room 100
Sacramento, CA 95814
Telephone: (916) 653-2621
Fax: (916) 651-9089
Date: May 8, 2026
To: All Bidders for IFB 25RS0030 Redding Server Room HVAC Minisplit
From: California Department of Veterans Affairs
Central Business Office
Subject: Addendum #1 – 25RS0030 Redding Server Room HVAC Minisplit
This Addendum is to make deletions, additions, changes, and clarifications to the solicitation referenced above.
The scope of this addendum is to replace the original bid set 25RS0030 Construction Drawings - Delta 1 OSFM Submission V2 03/17/26 with 25RS0030 Construction Drawings - Delta V3 OSFM Submission Addendum #1-V3 04/24/26.
CONSTRUCTION PROJECT MANUAL CLARIFICATIONS:
1. DELETE specification section 00 01 15 List of Drawings.
2. ADD specification section 00 01 15 List of Drawings Addendum 1.
CONSTRUCTION DRAWING CLARIFICATIONS:
3. DELETE Sheet G-0.0 General Vicinity Map, Site Map Project Data & Drawing Index V2 dated 03/17/26 REPLACE with Sheet G-0.0 General Vicinity Map, Site Map Project Data & Drawing Index V3 dated 04/24/26
4. ADD new sheets G-1.0 - General Fire Penetration Details V3 dated 04/24/26, G-2.0 - General UL Details V3 dated 04/24/26, and Sheet G-2.1 - General UL Details V3 dated 04/24/26 to drawing set.
5. DELETE Sheet M-3.0 Mechanical Details V2 dated 03/17/26. REPLACE with Sheet M-3.0 Mechanical Details V3 dated 04/24/26. (Add Detail 7 Pipe Through Roof Detail)
6. DELETE Sheet E-1.0 Electrical Enlarged Floor Plan (Building G) – MDF G14 V2 dated 03/17/26. REPLACE with Sheet E-1.0 Electrical Enlarged Floor Plan (Building G) – MDF G14 V3 dated 04/24/26. (Add callout for Detail 2/G-1.0)
7. DELETE Sheet E-1.1 Electrical Enlarged Roof Plan V2 dated 03/17/26. REPLACE with sheet E-1.1 Electrical Enlarged Roof Plan V3 dated 04/24/26. (Add notes 1 and 4 and Electrical Room G46)
8. DELETE Sheet E-3.0 Electrical Details V2 dated 03/17/26. REPLACE with Sheet E-3.0 Electrical Details V3 dated 04/24/26. (Delete Detail 1 Fire Stop Through Penetration Details)
STATE OF CALIFORNIA DEPARTMENT OF VETERANS AFFAIRS
LISTS OF DRAWINGS
CalVet: March 2026 00 01 15 - 1 - Project Number: CA25-0394
DOCUMENT 00 01 15
LIST OF DRAWINGS ADDENDUM 1 Dated 04/24/26
Sheet Number
Description Addendum Dated
ARCHITECTURAL
G-0.0 VINCINITY MAP, SITE MAP, PROJECT DATA & DRAWING INDEX 1 04/24/26
G-1.0 GENERAL FIRE PENETRATION DETAILS 1 04/24/26
G-2.0 GENERAL UL DETAILS 1 04/24/26
G-2.1 GENERAL UL DETAILS 1 04/24/26
MECHANICAL
M-0.0 MECHANICAL NOTES, SYMBOLS, AND ABBREVIATIONS
M-0.1 MECHANICAL EQUIPMENT SCHEDULES
M-0.2 MECHANICAL SPECIFICATIONS
M-1.0 MECHANICAL OVERALL FLOOR PLAN (SITE)
M-1.1 MECHANICAL FLOOR PLAN (BUILDING G)
M-1.2 MECHANICAL ENLARGED FLOOR PLAN (BUILDING G) – MDF G14
M-2.0 MECHANICAL BUILDING ROOF PLAN – NEW WORK
M-2.1 MECHANICAL ROOF PLAN (BUILDING G ROOF WELL)
M-3.0 MECHANICAL DETAILS 1 04/24/26
MC-0.1 MECHANICAL CONTROLS
MC-0.2 MECHANICAL CONTROLS
ELECTRICAL
E-0.0 ELECTRICAL NOTES, SYMBOLS AND ABBREVIATIONS
E-0.1 ELECTRICAL PANEL SCHEDULES
E-1.0 ELECTRICAL ENLARGED FLOOR PLAN (BUILDING G) – MDF G14 1 04/24/26
E-1.1 ELECTRICAL ROOF PLAN (BUILDING G ROOF WELL) 1 04/24/26
E-2.0 ELECTRICAL SPECIFICATIONS
E-3.0 ELECTRICAL DETAILS 1 04/24/26
END OF DOCUMENT
NATURAL AREA
LEV
CA
RP
OO
L
KNIGHTON ROAD (PUBLIC)
VAN
VAN
VAN
LEV
LEV
LEV
LEV
CARPOOL
CARPOOL
CA
RP
OO
L
CA
RP
OO
L
CARPOOL CARPOOL
10 O
FF
10 O
FF
CENTRAL
UTILITY
PLANT
D
C
F
B
A G
E
H
GENERAL
VICINITY MAP,
SITE MAP,
PROJECT DATA &
DRAWING INDEX
G-0.0
REV ECO DESCRIPTION DATE
ATTENTION:
ONLY WET SIGNED DOCUMENTS CONSTITUTE ADVANCE DESIGN
CONSULTANTS, INC. PROFESSIONAL WORK AND BECAUSE OTHER
REPRODUCIBLE DOCUMENTS MAY BE EASILY ALTERED WITHOUT THE
CONSENT OF ADVANCE DESIGN CONSULTANTS, INC., THE WET
SIGNED DOCUMENTS MUST BE REFERRED TO FOR THE ORIGINAL AND
CORRECT INFORMATION. IF THERE ANY DIFFERENCES BETWEEN THE
WET SIGNED DOCUMENTS AND ANY OTHER DOCUMENTS, THE WET
SIGNED DOCUMENTS SHALL GOVERN. ADVANCE DESIGN
CONSULTANTS, INC. IS NOT RESPONSIBLE FOR ANY MODIFICATIONS
MADE TO OUR DOCUMENTS BY ANYONE OTHER THAN AUTHORIZED
REPRESENTATIVES OF ADVANCE DESIGN CONSULTANTS, INC.
CALIFORNIA DEPARTMENT OF
VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
ENGINEERS:
ENGINEERING STAMP:
CLIENT:
PROJECT MANAGER:
DESIGN ENGINEER:
QUALITY REVIEW:
PRINCIPAL-IN-CHARGE:
ADC PROJECT NUMBER:
CLIENT PROJECT NUMBER:
DWG. TITLE:
DRAWING SCALE:
SHEET:
PROJECT TITLE:
ATTENTION:
THIS DOCUMENT IS THE PROPERTY OF THE CLIENT. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR
QUOTATION OR FOR THE PERFORMANCE OF WORK FOR THE CLIENT.
CALVET REDDING SERVER ROOM
HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
V2
CALIFORNIA DEPARTMENT OF VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
CALVET REDDING SERVER ROOM HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
OFFICE OF THE STATE FIRE MARSHAL
shall be available on the project site at all times.
5/6/2026
APPROVED FIRE AND PANIC ONLY
Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval is subject to field inspection. One set of approved plans
25-5700 klumos Snapshot klumos Snapshot klumos Snapshot
REV ECO DESCRIPTION DATE
ATTENTION:
ONLY WET SIGNED DOCUMENTS CONSTITUTE ADVANCE DESIGN
CONSULTANTS, INC. PROFESSIONAL WORK AND BECAUSE OTHER
REPRODUCIBLE DOCUMENTS MAY BE EASILY ALTERED WITHOUT THE
CONSENT OF ADVANCE DESIGN CONSULTANTS, INC., THE WET
SIGNED DOCUMENTS MUST BE REFERRED TO FOR THE ORIGINAL AND
CORRECT INFORMATION. IF THERE ANY DIFFERENCES BETWEEN THE
WET SIGNED DOCUMENTS AND ANY OTHER DOCUMENTS, THE WET
SIGNED DOCUMENTS SHALL GOVERN. ADVANCE DESIGN
CONSULTANTS, INC. IS NOT RESPONSIBLE FOR ANY MODIFICATIONS
MADE TO OUR DOCUMENTS BY ANYONE OTHER THAN AUTHORIZED
REPRESENTATIVES OF ADVANCE DESIGN CONSULTANTS, INC.
CALIFORNIA DEPARTMENT OF
VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
ENGINEERS:
ENGINEERING STAMP:
CLIENT:
PROJECT MANAGER:
DESIGN ENGINEER:
QUALITY REVIEW:
PRINCIPAL-IN-CHARGE:
ADC PROJECT NUMBER:
CLIENT PROJECT NUMBER:
DWG. TITLE:
DRAWING SCALE:
SHEET:
PROJECT TITLE:
ATTENTION:
THIS DOCUMENT IS THE PROPERTY OF THE CLIENT. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR
QUOTATION OR FOR THE PERFORMANCE OF WORK FOR THE CLIENT.
CALVET REDDING SERVER ROOM
HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
V2G-1.0
OFFICE OF THE STATE FIRE MARSHAL
shall be available on the project site at all times.
5/6/2026
APPROVED FIRE AND PANIC ONLY
Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval is subject to field inspection. One set of approved plans
25-5700 klumos Text Box klumos Snapshot klumos Text Box klumos Snapshot klumos Text Box
ONLY WET SIGNED DOCUMENTS CONSTITUTE ADVANCE DESIGN
CONSULTANTS, INC. PROFESSIONAL WORK AND BECAUSE OTHER
REPRODUCIBLE DOCUMENTS MAY BE EASILY ALTERED WITHOUT THE
CONSENT OF ADVANCE DESIGN CONSULTANTS, INC., THE WET
SIGNED DOCUMENTS MUST BE REFERRED TO FOR THE ORIGINAL AND
CORRECT INFORMATION. IF THERE ANY DIFFERENCES BETWEEN THE
WET SIGNED DOCUMENTS AND ANY OTHER DOCUMENTS, THE WET
SIGNED DOCUMENTS SHALL GOVERN. ADVANCE DESIGN
CONSULTANTS, INC. IS NOT RESPONSIBLE FOR ANY MODIFICATIONS
MADE TO OUR DOCUMENTS BY ANYONE OTHER THAN AUTHORIZED
REPRESENTATIVES OF ADVANCE DESIGN CONSULTANTS, INC.
CALIFORNIA DEPARTMENT OF
VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
ENGINEERS:
ENGINEERING STAMP:
CLIENT:
PROJECT MANAGER:
DESIGN ENGINEER:
QUALITY REVIEW:
PRINCIPAL-IN-CHARGE:
ADC PROJECT NUMBER:
CLIENT PROJECT NUMBER:
DWG. TITLE:
DRAWING SCALE:
SHEET:
PROJECT TITLE:
ATTENTION:
THIS DOCUMENT IS THE PROPERTY OF THE CLIENT. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR
QUOTATION OR FOR THE PERFORMANCE OF WORK FOR THE CLIENT.
CALVET REDDING SERVER ROOM
HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
V2G-2.0
OFFICE OF THE STATE FIRE MARSHAL
shall be available on the project site at all times.
5/6/2026
APPROVED FIRE AND PANIC ONLY
Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval is subject to field inspection. One set of approved plans
25-5700
ONLY WET SIGNED DOCUMENTS CONSTITUTE ADVANCE DESIGN
CONSULTANTS, INC. PROFESSIONAL WORK AND BECAUSE OTHER
REPRODUCIBLE DOCUMENTS MAY BE EASILY ALTERED WITHOUT THE
CONSENT OF ADVANCE DESIGN CONSULTANTS, INC., THE WET
SIGNED DOCUMENTS MUST BE REFERRED TO FOR THE ORIGINAL AND
CORRECT INFORMATION. IF THERE ANY DIFFERENCES BETWEEN THE
WET SIGNED DOCUMENTS AND ANY OTHER DOCUMENTS, THE WET
SIGNED DOCUMENTS SHALL GOVERN. ADVANCE DESIGN
CONSULTANTS, INC. IS NOT RESPONSIBLE FOR ANY MODIFICATIONS
MADE TO OUR DOCUMENTS BY ANYONE OTHER THAN AUTHORIZED
REPRESENTATIVES OF ADVANCE DESIGN CONSULTANTS, INC.
CALIFORNIA DEPARTMENT OF
VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
ENGINEERS:
ENGINEERING STAMP:
CLIENT:
PROJECT MANAGER:
DESIGN ENGINEER:
QUALITY REVIEW:
PRINCIPAL-IN-CHARGE:
ADC PROJECT NUMBER:
CLIENT PROJECT NUMBER:
DWG. TITLE:
DRAWING SCALE:
SHEET:
PROJECT TITLE:
ATTENTION:
THIS DOCUMENT IS THE PROPERTY OF THE CLIENT. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR
QUOTATION OR FOR THE PERFORMANCE OF WORK FOR THE CLIENT.
CALVET REDDING SERVER ROOM
HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
V2G-2.1
OFFICE OF THE STATE FIRE MARSHAL
shall be available on the project site at all times.
5/6/2026
APPROVED FIRE AND PANIC ONLY
Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval is subject
ONLY WET SIGNED DOCUMENTS CONSTITUTE ADVANCE DESIGN
CONSULTANTS, INC. PROFESSIONAL WORK AND BECAUSE OTHER
REPRODUCIBLE DOCUMENTS MAY BE EASILY ALTERED WITHOUT THE
CONSENT OF ADVANCE DESIGN CONSULTANTS, INC., THE WET
SIGNED DOCUMENTS MUST BE REFERRED TO FOR THE ORIGINAL AND
CORRECT INFORMATION. IF THERE ANY DIFFERENCES BETWEEN THE
WET SIGNED DOCUMENTS AND ANY OTHER DOCUMENTS, THE WET
SIGNED DOCUMENTS SHALL GOVERN. ADVANCE DESIGN
CONSULTANTS, INC. IS NOT RESPONSIBLE FOR ANY MODIFICATIONS
MADE TO OUR DOCUMENTS BY ANYONE OTHER THAN AUTHORIZED
REPRESENTATIVES OF ADVANCE DESIGN CONSULTANTS, INC.
CALIFORNIA DEPARTMENT OF
VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
ENGINEERS:
ENGINEERING STAMP:
CLIENT:
PROJECT MANAGER:
DESIGN ENGINEER:
QUALITY REVIEW:
PRINCIPAL-IN-CHARGE:
ADC PROJECT NUMBER:
CLIENT PROJECT NUMBER:
DWG. TITLE:
DRAWING SCALE:
SHEET:
PROJECT TITLE:
ATTENTION:
THIS DOCUMENT IS THE PROPERTY OF THE CLIENT. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR
QUOTATION OR FOR THE PERFORMANCE OF WORK FOR THE CLIENT.
CALVET REDDING SERVER ROOM
HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
V2
MECHANICAL
GENERAL NOTES,
ABBREVIATIONS
AND SYMBOLS
M-0.0
OFFICE OF THE STATE FIRE MARSHAL
shall be available on the project site at all times.
3/23/2026
APPROVED FIRE AND PANIC ONLY
Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval is subject to field inspection. One set of approved plans
25-5700
AutoCAD SHX Text 25-081
AutoCAD SHX Text
IFR-90%
AutoCAD SHX Text 11/17/25
AutoCAD SHX Text 25-092
AutoCAD SHX Text
IFR-100%
AutoCAD SHX Text 12/15/25
AutoCAD SHX Text 25-095
AutoCAD SHX Text
OSFM SUBMISSION V1
AutoCAD SHX Text 12/22/25
AutoCAD SHX Text 25-129
AutoCAD SHX Text
OSFM SUBMISSION V2
AutoCAD SHX Text 3/17/26
AutoCAD SHX Text 25-315-20
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 03/17/26
AutoCAD SHX Text
AutoCAD SHX Text
RUDY ALANIS
AutoCAD SHX Text O
AutoCAD SHX Text
EXP. 06/30/2027
AutoCAD SHX Text
NO. M 21000
AutoCAD SHX Text F
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text E
AutoCAD SHX Text T
AutoCAD SHX Text A
AutoCAD SHX Text T
AutoCAD SHX Text S
AutoCAD SHX Text N
AutoCAD SHX Text H
AutoCAD SHX Text C
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text I
AutoCAD SHX Text O
AutoCAD SHX Text F
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text I
AutoCAD SHX Text L
AutoCAD SHX Text E
AutoCAD SHX Text M
AutoCAD SHX Text N
AutoCAD SHX Text Z
AutoCAD SHX Text D
AutoCAD SHX Text E
AutoCAD SHX Text T
AutoCAD SHX Text R
AutoCAD SHX Text E
AutoCAD SHX Text G
AutoCAD SHX Text S
AutoCAD SHX Text I
AutoCAD SHX Text L
AutoCAD SHX Text O
AutoCAD SHX Text E
AutoCAD SHX Text R
AutoCAD SHX Text R
AutoCAD SHX Text E
AutoCAD SHX Text O
AutoCAD SHX Text R
AutoCAD SHX Text F
AutoCAD SHX Text R
AutoCAD SHX Text O
AutoCAD SHX Text A
AutoCAD SHX Text P
AutoCAD SHX Text
AutoCAD SHX Text E
AutoCAD SHX Text S
AutoCAD SHX Text S
AutoCAD SHX Text I
AutoCAD SHX Text O
AutoCAD SHX Text I
AutoCAD SHX Text S
AutoCAD SHX Text R
AutoCAD SHX Text N
AutoCAD SHX Text O
AutoCAD SHX Text A
AutoCAD SHX Text L
AutoCAD SHX Text I
AutoCAD SHX Text S
AutoCAD SHX Text T
AutoCAD SHX Text A
AutoCAD SHX Text N
AutoCAD SHX Text G
AutoCAD SHX Text E
AutoCAD SHX Text N
AutoCAD SHX Text O
AutoCAD SHX Text L
AutoCAD SHX Text L
AutoCAD SHX Text I
AutoCAD SHX Text R
AutoCAD SHX Text N
AutoCAD SHX Text E
AutoCAD SHX Text E
AutoCAD SHX Text E
AutoCAD SHX Text N
AutoCAD SHX Text A
AutoCAD SHX Text L
AutoCAD SHX Text
ABBREVIATIONS:
AutoCAD SHX Text
ABBR.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
ABBR.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
AMB
AutoCAD SHX Text
AMBIENT
AutoCAD SHX Text
BDD
AutoCAD SHX Text
BACKDRAFT DAMPER
AutoCAD SHX Text
BHP
AutoCAD SHX Text
BRAKE HORSEPOWER
AutoCAD SHX Text
BTU
AutoCAD SHX Text
BRITISH THERMAL UNIT
AutoCAD SHX Text
BTUH
AutoCAD SHX Text
BTU PER HOUR
AutoCAD SHX Text
CFM
AutoCAD SHX Text
CUBIC FEET PER MINUTE
AutoCAD SHX Text
COND
AutoCAD SHX Text
CONDENSATE
AutoCAD SHX Text
CU
AutoCAD SHX Text
CONDENSING UNIT
AutoCAD SHX Text
CUBIC FEET
AutoCAD SHX Text
DB
AutoCAD SHX Text
DRY BULB
AutoCAD SHX Text (E)
AutoCAD SHX Text
EXISTING
AutoCAD SHX Text
EAT
AutoCAD SHX Text
ENTERING AIR TEMPERATURE
AutoCAD SHX Text
EDB
AutoCAD SHX Text
ENTERING DRY BULB TEMPERATURE
AutoCAD SHX Text
EF
AutoCAD SHX Text
EXHAUST FAN
AutoCAD SHX Text
ELEC
AutoCAD SHX Text
ELECTRICAL
AutoCAD SHX Text
ESP
AutoCAD SHX Text
EXTERNAL STATIC PRESSURE
AutoCAD SHX Text °F
AutoCAD SHX Text
DEGREE FAHRENHEIT
AutoCAD SHX Text
FLA
AutoCAD SHX Text
FULL LOAD AMPS
AutoCAD SHX Text
FC
AutoCAD SHX Text
FAN COIL
AutoCAD SHX Text
FT
AutoCAD SHX Text
FEET
AutoCAD SHX Text
GPM
AutoCAD SHX Text
GALLONS PER MINUTE
AutoCAD SHX Text
GPH
AutoCAD SHX Text
GALLONS PER HOUR
AutoCAD SHX Text
HP
AutoCAD SHX Text
HORSEPOWER
AutoCAD SHX Text
HZ
AutoCAD SHX Text
HERTZ
AutoCAD SHX Text
IN
AutoCAD SHX Text
INCHES
AutoCAD SHX Text
LB
AutoCAD SHX Text
POUND
AutoCAD SHX Text
LBD
AutoCAD SHX Text
LEAVING DRY BULB TEMPERATURE
AutoCAD SHX Text
MAX
AutoCAD SHX Text
MAXIMUM
AutoCAD SHX Text
MBH
AutoCAD SHX Text
THOUSAND BTU PER HOUR
AutoCAD SHX Text
MIN
AutoCAD SHX Text
MINIMUM
AutoCAD SHX Text (N)
AutoCAD SHX Text
NEW
AutoCAD SHX Text
OA
AutoCAD SHX Text
OUTSIDE AIR
AutoCAD SHX Text
PSI
AutoCAD SHX Text
POUNDS PER SQUARE INCH
AutoCAD SHX Text
PSIG
AutoCAD SHX Text
POUNDS PER SQUARE INCH GAUGE
AutoCAD SHX Text
RA
AutoCAD SHX Text
RETURN AIR
AutoCAD SHX Text
SA
AutoCAD SHX Text
SUPPLY AIR
AutoCAD SHX Text
SD
AutoCAD SHX Text
SMOKE DETECTOR
AutoCAD SHX Text
SQ.FT.
AutoCAD SHX Text
SQUARE FEET
AutoCAD SHX Text
TEMP
AutoCAD SHX Text
TEMPERATURE
AutoCAD SHX Text
TSP
AutoCAD SHX Text
TOTAL STATIC PRESSURE
AutoCAD SHX Text
TYP
AutoCAD SHX Text
TYPICAL
AutoCAD SHX Text
VAV
AutoCAD SHX Text
VARIABLE AIR VOLUME
AutoCAD SHX Text
WB
AutoCAD SHX Text
WET BULB
AutoCAD SHX Text
WC
AutoCAD SHX Text
WATER COLUMN
AutoCAD SHX Text
WG
AutoCAD SHX Text
WATER GAUGE
AutoCAD SHX Text
MPT
AutoCAD SHX Text
MALE PIPE THREAD
AutoCAD SHX Text
NPT
AutoCAD SHX Text
NOMINAL PIPE THREAD
AutoCAD SHX Text
FPT
AutoCAD SHX Text
FEMALE PIPE THREAD
AutoCAD SHX Text
MCA
AutoCAD SHX Text
MINIMUM CIRCUIT AMPACITY
AutoCAD SHX Text
DN
AutoCAD SHX Text
DOWN
AutoCAD SHX Text (R)
AutoCAD SHX Text
RELOCATED
AutoCAD SHX Text
AHU
AutoCAD SHX Text
AIR HANDLING UNIT
AutoCAD SHX Text
AP
AutoCAD SHX Text
ACCESS PANEL
AutoCAD SHX Text
CT
AutoCAD SHX Text
COOLING TOWER
AutoCAD SHX Text
TF
AutoCAD SHX Text
TRANSFER FAN
AutoCAD SHX Text
CWR
AutoCAD SHX Text
CONDENSER WATER RETURN
AutoCAD SHX Text
CWS
AutoCAD SHX Text
CONDENSER WATER SUPPLY
AutoCAD SHX Text
CD
AutoCAD SHX Text
CONDENSATE DRAIN
AutoCAD SHX Text
BFP
AutoCAD SHX Text
BACKFLOW PREVENTER
AutoCAD SHX Text
MAV
AutoCAD SHX Text
MANUAL AIR VENT
AutoCAD SHX Text
FSD
AutoCAD SHX Text
FIRE-SMOKE DAMPER
AutoCAD SHX Text
CTP
AutoCAD SHX Text
COOLING TOWER PUMP
AutoCAD SHX Text
CWP
AutoCAD SHX Text
CONDENSER WATER PUMP
AutoCAD SHX Text
SYMB.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
CONCENTRIC REDUCER
AutoCAD SHX Text T
AutoCAD SHX Text P
AutoCAD SHX Text
PRESSURE GAUGE
AutoCAD SHX Text
TEMPERATURE GAUGE
AutoCAD SHX Text
CIRCUIT SETTER
AutoCAD SHX Text
2-WAY CONTROL VALVE
AutoCAD SHX Text
3-WAY CONTROL VALVE
AutoCAD SHX Text
FLEXIBLE CONNECTOR
AutoCAD SHX Text
UNION
AutoCAD SHX Text
FLOW METER
AutoCAD SHX Text
BUTTERFLY VALVE
AutoCAD SHX Text
ACTUATED BUTTERFLY VALVE
AutoCAD SHX Text
SHUT-OFF VALVE
AutoCAD SHX Text
BALL VALVE
AutoCAD SHX Text
PRESSURE REGULATOR
AutoCAD SHX Text
PNEUMATIC VALVE
AutoCAD SHX Text
Y-STRAINER
AutoCAD SHX Text
DIAPHRAGM VALVE
AutoCAD SHX Text
CHECK VALVE
AutoCAD SHX Text
RELIEF VALVE
AutoCAD SHX Text
AIR VENT
AutoCAD SHX Text
FM
AutoCAD SHX Text
PIPING
AutoCAD SHX Text
DHW
AutoCAD SHX Text
DOMESTIC HOT WATER
AutoCAD SHX Text
HW
AutoCAD SHX Text
HOT WATER
AutoCAD SHX Text
CW
AutoCAD SHX Text
CITY WATER
AutoCAD SHX Text
HWR
AutoCAD SHX Text
HOT WATER RETURN
AutoCAD SHX Text
HWS
AutoCAD SHX Text
HOT WATER SUPPLY
AutoCAD SHX Text
HWP
AutoCAD SHX Text
HOT WATER PUMP
AutoCAD SHX Text
ET
AutoCAD SHX Text
EXPANSION TANK
AutoCAD SHX Text
WH
AutoCAD SHX Text
WATER HEATER
AutoCAD SHX Text GENERAL NOTES: A. CODE COMPLIANCE: THE CONTRACTOR SHALL COMPLY WITH ALL APPLICABLE NATIONAL, STATE, AND LOCAL CODES ISSUED BY THE AUTHORITIES HAVING JURISDICTION. THE COMPLETE MECHANICAL INSTALLATION SHALL BE IN ACCORDANCE WITH THE ADOPTED EDITION OF CMC, UMC, UPC, UFC, UBC, TITLE 24, OSHA, NFPA, AND ALL CLIENT REQUIREMENTS, THE LATEST RULES AND REGULATIONS OF THE SAFETY ORDERS ISSUED BY THE DIVISION OF INDUSTRIAL SAFETY, STATE OF CALIFORNIA. B. "AS-BUILT" DRAWINGS: THE CONTRACTOR SHALL MAINTAIN AT THE JOB AN UP-TO-DATE "AS-BUILT" DRAWING SET. THE "AS-BUILT" DRAWING SET SHALL REFLECT ALL APPROVED CHANGES TO THE DESIGN DRAWINGS. THE "AS-BUILT" DRAWINGS SET SHALL BE KEPT CLEAN AND IN GOOD CONDITION AND SHALL BE TURNED OVER THE PROJECT MANAGER TWO (2) WEEKS AFTER COMPLETION OF THE PROJECT. C. FUNCTIONAL TEST AND ACCEPTANCE: UPON COMPLETION OF THE PROJECT, THE CONTRACTOR SHALL SCHEDULE AND PERFORM A COMPLETE FUNCTIONAL TEST TO DEMONSTRATE TO THE PROJECT MANAGER THAT THE MECHANICAL SYSTEMS ARE OPERATING AS INTENDED. ANY DEFECTS OR DISCREPANCIES IN THE MATERIAL OR WORK SHALL BE CORRECTED IMMEDIATELY TO THE SATISFACTION OF THE PROJECT MANAGER AT NO ADDITIONAL COST, NOISY OPERATION AND/OR VIBRATION TRANSMISSION TO THE BLDG. STRUCTURE WILL NOT BE ACCEPTED. D. CONTRACTOR'S RESPONSIBILITY: CONTRACTOR SHALL BE RESPONSIBLE FOR OBTAINING ACCURATE SHOP DRAWING INFORMATION SUCH AS WEIGHT, SIZE, ROOF OPENING LOCATIONS, WEIGHT DISTRIBUTION, ETC., FOR ALL EQUIPMENT AND MATERIALS. ANY CORRECTIVE MEASURE ARISING FROM LACK OF COORDINATION WILL BE THE SOLE RESPONSIBILITY OF THE CONTRACTOR. E. GENERAL REQUIREMENTS: 1. ALL EQUIPMENT SHALL BE INSTALLED IN STRICT ACCORDANCE WITH THE EQUIPMENT ALL EQUIPMENT SHALL BE INSTALLED IN STRICT ACCORDANCE WITH THE EQUIPMENT MANUFACTURE'S RECOMMENDATIONS. PROVIDE ALL FITTINGS, TRANSITIONS, DAMPERS, AND OTHER DEVICES REQUIRED FOR A COMPLETE WORKABLE INSTALLATION. 2. DRAWINGS ARE DIAGRAMMATICAL, AND INDICATE GENERAL ARRANGEMENT OF THE DRAWINGS ARE DIAGRAMMATICAL, AND INDICATE GENERAL ARRANGEMENT OF THE HVAC SYSTEM ONLY. THE CONTRACTOR SHALL FIELD COORDINATE ALL DUCTWORK INSTALLATIONS AND SUPPORTS, WHERE REQUIRED, AND NECESSARY. 3. INSTALL SEISMIC BRACING FOR ALL NEW EQUIPMENT IN ACCORDANCE WITH INSTALL SEISMIC BRACING FOR ALL NEW EQUIPMENT IN ACCORDANCE WITH CALIFORNIA ADMINISTRATIVE CODE, TITLE 24, AND LATERAL FORCE ANCHORAGE PROVISIONS. 4. ALL NEW MECHANICAL EQUIPMENT SHALL BE LISTED BY A NATIONALLY RECOGNIZED ALL NEW MECHANICAL EQUIPMENT SHALL BE LISTED BY A NATIONALLY RECOGNIZED UL LISTED AND PROPERLY LABELED, AND PROVIDE MANUFACTURER'S CUT SHEETS AND SPECIFICATION FOR EACH UNIT. 5. REFRIGERANT PIPING SYSTEM TO BE INSTALLED PER MANUFACTURER REFRIGERANT PIPING SYSTEM TO BE INSTALLED PER MANUFACTURER RECOMMENDATIONS. PROVIDE ALL COMPONENTS FOR A COMPLETE WORKABLE SYSTEM. 6. ALL DUCTWORK SHALL BE CONSTRUCTED, ERECTED, AND TESTED IN ACCORDANCE ALL DUCTWORK SHALL BE CONSTRUCTED, ERECTED, AND TESTED IN ACCORDANCE WITH THE MOST RESTRICTIVE OF LOCAL REGULATIONS, PROCEDURES DETAILED IN THE ASHRAE HANDBOOK OF FUNDAMENTALS, OR THE APPLICABLE STANDARDS ADOPTED BY THE SHEET METAL AND AIR CONDITIONING CONTRACTORS NATIONAL ASSOCIATION. 7. DUCT SEALING/DUCT LEAKAGE SHALL NOT EXCEED 6% OF FAN AIR-FLOW. TEST DUCT SEALING/DUCT LEAKAGE SHALL NOT EXCEED 6% OF FAN AIR-FLOW. TEST DUCT SYSTEM AS REQUIRED PER PRESCRIPTIVE D COMPLIANCE REQUIREMENTS. 8. THE DUCT SYSTEMS SHALL BE CONSTRUCTED PER CMC 602.5 TABLES NOS. 6-1, THE DUCT SYSTEMS SHALL BE CONSTRUCTED PER CMC 602.5 TABLES NOS. 6-1, 6-2 AND 6-3 PER CMC STANDARD 6-1 OR 6-2. FLEXIBLE FACTORY-MADE AIR DUCTS SHALL BE CLASS 0 OR CLASS 1 MEET ALL REQUIREMENTS OF CMC 604.2. 9. MATERIAL EXPOSED WITHIN DUCTS OR PLENUM SHALL HAVE A FLAME-SPREAD MATERIAL EXPOSED WITHIN DUCTS OR PLENUM SHALL HAVE A FLAME-SPREAD INDEX OF NOT MORE THAN 25 AND SMOKE DEVELOPED RATING OF NOT MORE THAN 50 FOR MATERIAL EXPOSED WITHIN THE DUCT/PLENUM AND/OR INSULATION MATERIALS APPLIED TO THE EXTERIOR OF THE DUCTS LOCATED IN THE BUILDING. CMC 602.2 AND/OR 605.0. 10. THE CONTRACTOR IS RESPONSIBLE FOR THE COORDINATION WITH ALL OTHER THE CONTRACTOR IS RESPONSIBLE FOR THE COORDINATION WITH ALL OTHER TRADES AND PROJECT MANAGER. 11. TEST AND BALANCE HVAC SYSTEM TO CFM'S SHOWN IN THE PLANS. TEST AND BALANCE HVAC SYSTEM TO CFM'S SHOWN IN THE PLANS. 12. DUCT/PIPE PENETRATIONS THROUGH FIRE RATED WALL TO COMPLY WITH DUCT/PIPE PENETRATIONS THROUGH FIRE RATED WALL TO COMPLY WITH CALIFORNIA FIRE CODE AND SEALED WITH UL LISTED FIRE RATED RED CAULK AND LOW VOC PER CBC PART 11 SECTION 11 5.714.4.4.1. 13. ADHESIVES TO BE LOW VOC AND COMPLY WITH CALIFORNIA CODE OF REGULATIONS ADHESIVES TO BE LOW VOC AND COMPLY WITH CALIFORNIA CODE OF REGULATIONS TITLE-17 FOR AEROSOL ADHESIVES. 14. NEW EQUIPMENT SHALL NOT CONTAIN CFC'S OR HALONS. NEW EQUIPMENT SHALL NOT CONTAIN CFC'S OR HALONS. 15. DUCTS/PIPES TO BE CLEAN AND FREE OF DUST AND DEBRIS DURING DUCTS/PIPES TO BE CLEAN AND FREE OF DUST AND DEBRIS DURING INSTALLATION. 16. PROTECT DUCT OPENINGS AND MECHANICAL EQUIPMENT DURING CONSTRUCTION. PROTECT DUCT OPENINGS AND MECHANICAL EQUIPMENT DURING CONSTRUCTION. 17. PROTECT THE PUBLIC DURING THE ENTIRE PROGRESS OF WORK BY POSTING PROTECT THE PUBLIC DURING THE ENTIRE PROGRESS OF WORK BY POSTING SIGNS, GUARD LIGHTS AND BARRICADES. 18. DEBRIS SHALL BE REMOVED FROM THE PREMISES ON A DAILY BASIS. DO NOT DEBRIS SHALL BE REMOVED FROM THE PREMISES ON A DAILY BASIS. DO NOT ALLOW DEBRIS TO ACCUMULATE. PROTECT ADJACENT AREAS FROM DUST AND DEBRIS.
AutoCAD SHX Text
SYMBOLS:
AutoCAD SHX Text
SYMB.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text X
AutoCAD SHX Text
XXX
AutoCAD SHX Text
EQUIPMENT TYPE
AutoCAD SHX Text
EQUIPMENT NO.
AutoCAD SHX Text
500 CFM
AutoCAD SHX Text A/12"%%C
AutoCAD SHX Text
TYPE OF DIFFUSER
AutoCAD SHX Text
NECK DIA.
AutoCAD SHX Text
CFM
AutoCAD SHX Text
CEILING DIFFUSER. ARROWS INDICATE DIRECTIONS OF THROW
AutoCAD SHX Text
EQUIPMENT TAG.
AutoCAD SHX Text
RETURN GRILLE
AutoCAD SHX Text
EXHAUST GRILLE
AutoCAD SHX Text
THERMOSTAT
AutoCAD SHX Text
REDUCER
AutoCAD SHX Text
DEMOLITION NOTE
AutoCAD SHX Text
GENERAL NOTE
AutoCAD SHX Text
SHEET NOTE
AutoCAD SHX Text T
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
POINT OF CONNECTION
AutoCAD SHX Text
NEW
AutoCAD SHX Text
EXISTING
AutoCAD SHX Text
MECHANICAL
AutoCAD SHX Text
CHW
AutoCAD SHX Text
CHILLED WATER
AutoCAD SHX Text
CHWR
AutoCAD SHX Text
CHILLED WATER RETURN
AutoCAD SHX Text
CHWS
AutoCAD SHX Text
CHILLED WATER SUPPLY
AutoCAD SHX Text
CHWP
AutoCAD SHX Text
CHILLED WATER PUMP
AutoCAD SHX Text
PCW
AutoCAD SHX Text
PROCESS COOLING WATER
AutoCAD SHX Text
PCWP
AutoCAD SHX Text
PROCESS COOLING WATER PUMP
AutoCAD SHX Text
PCWR
AutoCAD SHX Text
PROCESS COOLING WATER RETURN
AutoCAD SHX Text
PCWS
AutoCAD SHX Text
PROCESS COOLING WATER SUPPLY
AutoCAD SHX Text
AS
AutoCAD SHX Text
AIR SEPARATOR
AutoCAD SHX Text
CHW
AutoCAD SHX Text
CU FT
AutoCAD SHX Text
CP
AutoCAD SHX Text
CONDENSATE PUMP
AutoCAD SHX Text
BG
AutoCAD SHX Text
BLAST GATE
AutoCAD SHX Text
MUW
AutoCAD SHX Text
MAKE UP WATER
AutoCAD SHX Text
VD
AutoCAD SHX Text
VOLUMETRIC DAMPER
AutoCAD SHX Text
FACP
AutoCAD SHX Text
FIRE ALARM CONTROL PANEL
AutoCAD SHX Text
PIPE SECTION
AutoCAD SHX Text
PIPE PN
AutoCAD SHX Text
PIPE UP
AutoCAD SHX Text
PIPE BRANCH DN
AutoCAD SHX Text
45° PIPE DN
AutoCAD SHX Text
CAP (WELD)
AutoCAD SHX Text
CAP THREAD
AutoCAD SHX Text
PUMP
AutoCAD SHX Text
METRAFLEX EXPANSION
AutoCAD SHX Text BUILDING G - MDF G14 1. SERVER (MDF) ROOM G14 SERVER (MDF) ROOM G14 INSTALLATION OF A NEW BACKUP SPLIT SYSTEM COOLING UNIT. NEW UNIT TO BE A MITSUBISHI 3-TON HEAT PUMP AND WALL MOUNTED FAN COIL UNIT. NEW SPLIT SYSTEM UNIT TO BE TIED INTO THE EXISTING BMS SYSTEM AND TO RUN IN THE EVENT THAT THE EXISTING FAN COIL UNIT SERVING THE MDF ROOM GOES DOWN.
AutoCAD SHX Text
%%UMECHANICAL SCOPE OF WORK
AutoCAD SHX Text
RF
AutoCAD SHX Text
RELIEF FAN
AutoCAD SHX Text
MECHANICAL DRAWING INDEX
AutoCAD SHX Text
DRAWING NUMBER
AutoCAD SHX Text
DISCIPLINE
AutoCAD SHX Text M-0.0
AutoCAD SHX Text
MECHANICAL NOTES, SYMBOLS AND ABBREVIATIONS
AutoCAD SHX Text M-0.1
AutoCAD SHX Text
MECHANICAL EQUIPMENT SCHEDULES
AutoCAD SHX Text M-0.2
AutoCAD SHX Text
MECHANICAL SPECIFICATIONS
AutoCAD SHX Text M-0.3
AutoCAD SHX Text
TITLE-24 FORMS
AutoCAD SHX Text M-1.0
AutoCAD SHX Text
MECHANICAL OVERALL FLOOR PLAN (SITE)
AutoCAD SHX Text M-1.1
AutoCAD SHX Text
MECHANICAL FLOOR PLAN (BUILDING G)
AutoCAD SHX Text M-1.2
AutoCAD SHX Text
MECHANICAL ENLARGED FLOOR PLAN (BUILDING G) - MDF G14
AutoCAD SHX Text M-2.1
AutoCAD SHX Text
MECHANICAL ROOF PLAN (BUILDING G ROOF WELL)
AutoCAD SHX Text M-3.0
AutoCAD SHX Text
MECHANICAL DETAILS
AutoCAD SHX Text
MC-0.1
AutoCAD SHX Text
MECHANICAL CONTROLS ARCHITECTURE
AutoCAD SHX Text
MC-0.2
AutoCAD SHX Text
MECHANICAL CONTROLS ARCHITECTURE
ONLY WET SIGNED DOCUMENTS CONSTITUTE ADVANCE DESIGN
CONSULTANTS, INC. PROFESSIONAL WORK AND BECAUSE OTHER
REPRODUCIBLE DOCUMENTS MAY BE EASILY ALTERED WITHOUT THE
CONSENT OF ADVANCE DESIGN CONSULTANTS, INC., THE WET
SIGNED DOCUMENTS MUST BE REFERRED TO FOR THE ORIGINAL AND
CORRECT INFORMATION. IF THERE ANY DIFFERENCES BETWEEN THE
WET SIGNED DOCUMENTS AND ANY OTHER DOCUMENTS, THE WET
SIGNED DOCUMENTS SHALL GOVERN. ADVANCE DESIGN
CONSULTANTS, INC. IS NOT RESPONSIBLE FOR ANY MODIFICATIONS
MADE TO OUR DOCUMENTS BY ANYONE OTHER THAN AUTHORIZED
REPRESENTATIVES OF ADVANCE DESIGN CONSULTANTS, INC.
CALIFORNIA DEPARTMENT OF
VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
ENGINEERS:
ENGINEERING STAMP:
CLIENT:
PROJECT MANAGER:
DESIGN ENGINEER:
QUALITY REVIEW:
PRINCIPAL-IN-CHARGE:
ADC PROJECT NUMBER:
CLIENT PROJECT NUMBER:
DWG. TITLE:
DRAWING SCALE:
SHEET:
PROJECT TITLE:
ATTENTION:
THIS DOCUMENT IS THE PROPERTY OF THE CLIENT. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR
QUOTATION OR FOR THE PERFORMANCE OF WORK FOR THE CLIENT.
CALVET REDDING SERVER ROOM
HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
V2
MECHANICAL
EQUIPMENT
SCHEDULES
M-0.1
OFFICE OF THE STATE FIRE MARSHAL
shall be available on the project site at all times.
3/23/2026
APPROVED FIRE AND PANIC ONLY
Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval is subject to field inspection. One set of approved plans
25-5700
AutoCAD SHX Text 25-081
AutoCAD SHX Text
IFR-90%
AutoCAD SHX Text 11/17/25
AutoCAD SHX Text 25-092
AutoCAD SHX Text
IFR-100%
AutoCAD SHX Text 12/15/25
AutoCAD SHX Text 25-095
AutoCAD SHX Text
OSFM SUBMISSION V1
AutoCAD SHX Text 12/22/25
AutoCAD SHX Text 25-129
AutoCAD SHX Text
OSFM SUBMISSION V2
AutoCAD SHX Text 3/17/26
AutoCAD SHX Text 25-315-20
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 03/17/26
AutoCAD SHX Text
AutoCAD SHX Text
RUDY ALANIS
AutoCAD SHX Text O
AutoCAD SHX Text
EXP. 06/30/2027
AutoCAD SHX Text
NO. M 21000
AutoCAD SHX Text F
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text E
AutoCAD SHX Text T
AutoCAD SHX Text A
AutoCAD SHX Text T
AutoCAD SHX Text S
AutoCAD SHX Text N
AutoCAD SHX Text H
AutoCAD SHX Text C
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text I
AutoCAD SHX Text O
AutoCAD SHX Text F
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text I
AutoCAD SHX Text L
AutoCAD SHX Text E
AutoCAD SHX Text M
AutoCAD SHX Text N
AutoCAD SHX Text Z
AutoCAD SHX Text D
AutoCAD SHX Text E
AutoCAD SHX Text T
AutoCAD SHX Text R
AutoCAD SHX Text E
AutoCAD SHX Text G
AutoCAD SHX Text S
AutoCAD SHX Text I
AutoCAD SHX Text L
AutoCAD SHX Text O
AutoCAD SHX Text E
AutoCAD SHX Text R
AutoCAD SHX Text R
AutoCAD SHX Text E
AutoCAD SHX Text O
AutoCAD SHX Text R
AutoCAD SHX Text F
AutoCAD SHX Text R
AutoCAD SHX Text O
AutoCAD SHX Text A
AutoCAD SHX Text P
AutoCAD SHX Text
AutoCAD SHX Text E
AutoCAD SHX Text S
AutoCAD SHX Text S
AutoCAD SHX Text I
AutoCAD SHX Text O
AutoCAD SHX Text I
AutoCAD SHX Text S
AutoCAD SHX Text R
AutoCAD SHX Text N
AutoCAD SHX Text O
AutoCAD SHX Text A
AutoCAD SHX Text L
AutoCAD SHX Text I
AutoCAD SHX Text S
AutoCAD SHX Text T
AutoCAD SHX Text A
AutoCAD SHX Text N
AutoCAD SHX Text G
AutoCAD SHX Text E
AutoCAD SHX Text N
AutoCAD SHX Text O
AutoCAD SHX Text L
AutoCAD SHX Text L
AutoCAD SHX Text I
AutoCAD SHX Text R
AutoCAD SHX Text N
AutoCAD SHX Text E
AutoCAD SHX Text E
AutoCAD SHX Text E
AutoCAD SHX Text N
AutoCAD SHX Text A
AutoCAD SHX Text L
AutoCAD SHX Text
EXISTING SPLIT SYSTEM OUTDOOR HEAT PUMP UNIT SCHEDULE
AutoCAD SHX Text
EQUIPMENT TAG
AutoCAD SHX Text
MANUFACTURER MODEL NO.
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
SERVES
AutoCAD SHX Text
COOLING
AutoCAD SHX Text
CONDENSING UNIT
AutoCAD SHX Text
ELECTRICAL
AutoCAD SHX Text
REFRIGERANT
AutoCAD SHX Text DIMENSION HxWxD
AutoCAD SHX Text
WEIGHT
AutoCAD SHX Text
REMARKS
AutoCAD SHX Text
TOTAL (MBH)
AutoCAD SHX Text
SENSIBLE (MBH)
AutoCAD SHX Text
OUTDOOR AMBIENT TEMP (°F)
AutoCAD SHX Text
COMPRESSOR
AutoCAD SHX Text
CONDENSER FAN
AutoCAD SHX Text V
AutoCAD SHX Text
PH
AutoCAD SHX Text
HZ
AutoCAD SHX Text
MOCP
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
CHARGE
AutoCAD SHX Text
GAS
AutoCAD SHX Text
LIQUID
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
FLA
AutoCAD SHX Text
WSA
AutoCAD SHX Text
HP
AutoCAD SHX Text
LBS
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
LBS
AutoCAD SHX Text
LIEBERT PFH37A
AutoCAD SHX Text
PROP-FAN CONDENSINGUNIT
AutoCAD SHX Text
MDF G14 INDOOR FAN COIL
AutoCAD SHX Text 32.8
AutoCAD SHX Text 27.4
AutoCAD SHX Text
AutoCAD SHX Text
SCROLL COMPRESSOR TYPE
AutoCAD SHX Text 7.4A
AutoCAD SHX Text 8.8A
AutoCAD SHX Text 0.2
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text R-407C
AutoCAD SHX Text
AutoCAD SHX Text 78"
AutoCAD SHX Text 12"
AutoCAD SHX Text 31"x48"x18"
AutoCAD SHX Text
AutoCAD SHX Text
PROVIDE POWER TO INDOOR FAN COIL.
AutoCAD SHX Text
EXISTING SPLIT SYSTEM INDOOR FAN COIL UNIT SCHEDULE
AutoCAD SHX Text
EQUIPMENT TAG
AutoCAD SHX Text
MANUFACTURER MODEL NO.
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
SERVES
AutoCAD SHX Text
SUPPLY FAN
AutoCAD SHX Text
COOLING
AutoCAD SHX Text
CONDENSATE DRAIN
AutoCAD SHX Text
REFRIGERANT
AutoCAD SHX Text DIMENSION HxWxD
AutoCAD SHX Text
WEIGHT
AutoCAD SHX Text
REMARKS
AutoCAD SHX Text
AIR FLOW (CFM)
AutoCAD SHX Text
BHP
AutoCAD SHX Text
FLA
AutoCAD SHX Text
CAPACITY (MBH)
AutoCAD SHX Text
SENS. (MBH) @ AHRI
AutoCAD SHX Text
OUTDOOR (°F)
AutoCAD SHX Text
INDOOR (°F)
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
GAS
AutoCAD SHX Text
LIQUID
AutoCAD SHX Text
DB
AutoCAD SHX Text
WB
AutoCAD SHX Text
DB
AutoCAD SHX Text
WB
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
LBS
AutoCAD SHX Text
LIEBERT MMD36E
AutoCAD SHX Text
HORIZONTAL FAN COIL
AutoCAD SHX Text
MDF G14 INDOOR FAN COIL
AutoCAD SHX Text
AutoCAD SHX Text 0.5
AutoCAD SHX Text 1.4
AutoCAD SHX Text 32.8
AutoCAD SHX Text 27.4
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 34"
AutoCAD SHX Text R-407C
AutoCAD SHX Text 78"
AutoCAD SHX Text 12"
AutoCAD SHX Text 24"x30"x57 "1316"
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
NEW SPLIT SYSTEM OUTDOOR CONDENSING UNIT SCHEDULE
AutoCAD SHX Text
EQUIPMENT TAG
AutoCAD SHX Text
MANUFACTURER MODEL NO.
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
SERVES
AutoCAD SHX Text
COOLING
AutoCAD SHX Text
CONDENSING UNIT
AutoCAD SHX Text
ELECTRICAL
AutoCAD SHX Text
REFRIGERANT
AutoCAD SHX Text DIMENSION HxWxD
AutoCAD SHX Text
WEIGHT
AutoCAD SHX Text
REMARKS
AutoCAD SHX Text
CAPACITY (MBH)
AutoCAD SHX Text
EER2
AutoCAD SHX Text
SEER2
AutoCAD SHX Text
OUTDOOR AMBIENT TEMP (°F)
AutoCAD SHX Text
COMPRESSOR
AutoCAD SHX Text
FAN
AutoCAD SHX Text V
AutoCAD SHX Text
PH
AutoCAD SHX Text
HZ
AutoCAD SHX Text
MCA
AutoCAD SHX Text
MOCP
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
PRE-CHARGE
AutoCAD SHX Text
GAS
AutoCAD SHX Text
LIQUID
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
RLA
AutoCAD SHX Text
AIRFLOW
AutoCAD SHX Text W
AutoCAD SHX Text
FLA
AutoCAD SHX Text
LBS
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
LBS
AutoCAD SHX Text
MITSUBISHI PUY-AK36NL
AutoCAD SHX Text
SPLIT COOLING ONLY
AutoCAD SHX Text
INDOOR FAN COIL
AutoCAD SHX Text 33.4
AutoCAD SHX Text 12.0
AutoCAD SHX Text 20.3
AutoCAD SHX Text
AutoCAD SHX Text
TWIN ROTARY
AutoCAD SHX Text
AutoCAD SHX Text 3,910
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text R-454B
AutoCAD SHX Text 9.0
AutoCAD SHX Text 58"
AutoCAD SHX Text 38"
AutoCAD SHX Text 52 "x41 "x14"4364"x41 "x14"1132"x14"
AutoCAD SHX Text
AutoCAD SHX Text PROVIDE POWER TO INDOOR FAN COIL. PROVIDE WITH LOW AMBIENT KIT. PROVIDE 1" DEFLECTION SPRING ISOLATORS
AutoCAD SHX Text
CU
AutoCAD SHX Text
AutoCAD SHX Text
NEW SPLIT SYSTEM INDOOR FAN COIL UNIT SCHEDULE
AutoCAD SHX Text
EQUIPMENT TAG
AutoCAD SHX Text
MANUFACTURER MODEL NO.
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
SERVES
AutoCAD SHX Text
SUPPLY FAN
AutoCAD SHX Text
COOLING
AutoCAD SHX Text
CONDENSATE DRAIN
AutoCAD SHX Text
REFRIGERANT
AutoCAD SHX Text DIMENSION HxWxD
AutoCAD SHX Text
WEIGHT
AutoCAD SHX Text
REMARKS
AutoCAD SHX Text
AIR FLOW (CFM)
AutoCAD SHX Text W
AutoCAD SHX Text
FLA
AutoCAD SHX Text
CAPACITY (MBH)
AutoCAD SHX Text
SENS. (MBH) @ AHRI
AutoCAD SHX Text
OUTDOOR (°F)
AutoCAD SHX Text
INDOOR (°F)
AutoCAD SHX Text
TYPE
AutoCAD SHX Text
GAS
AutoCAD SHX Text
LIQUID
AutoCAD SHX Text
DB
AutoCAD SHX Text
WB
AutoCAD SHX Text
DB
AutoCAD SHX Text
WB
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
INCH
AutoCAD SHX Text
LBS
AutoCAD SHX Text
MITSUBISHI PKA-AK36NL
AutoCAD SHX Text
WALL MOUNTED
AutoCAD SHX Text
MDF G14 ROOM
AutoCAD SHX Text 705, 810, 920
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 26.6
AutoCAD SHX Text 20.04
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 58"
AutoCAD SHX Text R-454B
AutoCAD SHX Text 58"
AutoCAD SHX Text 38"
AutoCAD SHX Text 14 "x46 "x11 "38"x46 "x11 "x46 "x11 "116"x11 "58"
AutoCAD SHX Text
AutoCAD SHX Text 1, 2, 3, 4
AutoCAD SHX Text
FC
AutoCAD SHX Text
AutoCAD SHX Text (E)
AutoCAD SHX Text NOTE: 1. PROVIDE WITH PROCON BACNET AND MODBUS INTERFACE AND TIE INTO EXISTING BMS PROVIDE WITH PROCON BACNET AND MODBUS INTERFACE AND TIE INTO EXISTING BMS SYSTEM TO RUN AS BACKUP. 2. PROVIDE WITH DISCONNECT SWITCH. PROVIDE WITH DISCONNECT SWITCH. 3. POWERED FROM OUTDOOR CONDENSING UNIT. POWERED FROM OUTDOOR CONDENSING UNIT. 4. 35 AMP RECOMMENDED FUSE/BREAKER SIZE (OUTDOOR) 35 AMP RECOMMENDED FUSE/BREAKER SIZE (OUTDOOR)
AutoCAD SHX Text
C-CU
AutoCAD SHX Text
AutoCAD SHX Text (E)
AutoCAD SHX Text
CRAC
ONLY WET SIGNED DOCUMENTS CONSTITUTE ADVANCE DESIGN
CONSULTANTS, INC. PROFESSIONAL WORK AND BECAUSE OTHER
REPRODUCIBLE DOCUMENTS MAY BE EASILY ALTERED WITHOUT THE
CONSENT OF ADVANCE DESIGN CONSULTANTS, INC., THE WET
SIGNED DOCUMENTS MUST BE REFERRED TO FOR THE ORIGINAL AND
CORRECT INFORMATION. IF THERE ANY DIFFERENCES BETWEEN THE
WET SIGNED DOCUMENTS AND ANY OTHER DOCUMENTS, THE WET
SIGNED DOCUMENTS SHALL GOVERN. ADVANCE DESIGN
CONSULTANTS, INC. IS NOT RESPONSIBLE FOR ANY MODIFICATIONS
MADE TO OUR DOCUMENTS BY ANYONE OTHER THAN AUTHORIZED
REPRESENTATIVES OF ADVANCE DESIGN CONSULTANTS, INC.
CALIFORNIA DEPARTMENT OF
VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
ENGINEERS:
ENGINEERING STAMP:
CLIENT:
PROJECT MANAGER:
DESIGN ENGINEER:
QUALITY REVIEW:
PRINCIPAL-IN-CHARGE:
ADC PROJECT NUMBER:
CLIENT PROJECT NUMBER:
DWG. TITLE:
DRAWING SCALE:
SHEET:
PROJECT TITLE:
ATTENTION:
THIS DOCUMENT IS THE PROPERTY OF THE CLIENT. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR
QUOTATION OR FOR THE PERFORMANCE OF WORK FOR THE CLIENT.
CALVET REDDING SERVER ROOM
HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
V2
MECHANICAL
SPECIFICATIONS
M-0.2
OFFICE OF THE STATE FIRE MARSHAL
shall be available on the project site at all times.
3/23/2026
APPROVED FIRE AND PANIC ONLY
Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval is subject to field inspection. One set of approved plans
25-5700
AutoCAD SHX Text 25-081
AutoCAD SHX Text
IFR-90%
AutoCAD SHX Text 11/17/25
AutoCAD SHX Text 25-092
AutoCAD SHX Text
IFR-100%
AutoCAD SHX Text 12/15/25
AutoCAD SHX Text 25-095
AutoCAD SHX Text
OSFM SUBMISSION V1
AutoCAD SHX Text 12/22/25
AutoCAD SHX Text 25-129
AutoCAD SHX Text
OSFM SUBMISSION V2
AutoCAD SHX Text 3/17/26
AutoCAD SHX Text 25-315-20
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 03/17/26
AutoCAD SHX Text
AutoCAD SHX Text
RUDY ALANIS
AutoCAD SHX Text O
AutoCAD SHX Text
EXP. 06/30/2027
AutoCAD SHX Text
NO. M 21000
AutoCAD SHX Text F
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text E
AutoCAD SHX Text T
AutoCAD SHX Text A
AutoCAD SHX Text T
AutoCAD SHX Text S
AutoCAD SHX Text N
AutoCAD SHX Text H
AutoCAD SHX Text C
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text I
AutoCAD SHX Text O
AutoCAD SHX Text F
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text I
AutoCAD SHX Text L
AutoCAD SHX Text E
AutoCAD SHX Text M
AutoCAD SHX Text N
AutoCAD SHX Text Z
AutoCAD SHX Text D
AutoCAD SHX Text E
AutoCAD SHX Text T
AutoCAD SHX Text R
AutoCAD SHX Text E
AutoCAD SHX Text G
AutoCAD SHX Text S
AutoCAD SHX Text I
AutoCAD SHX Text L
AutoCAD SHX Text O
AutoCAD SHX Text E
AutoCAD SHX Text R
AutoCAD SHX Text R
AutoCAD SHX Text E
AutoCAD SHX Text O
AutoCAD SHX Text R
AutoCAD SHX Text F
AutoCAD SHX Text R
AutoCAD SHX Text O
AutoCAD SHX Text A
AutoCAD SHX Text P
AutoCAD SHX Text
AutoCAD SHX Text E
AutoCAD SHX Text S
AutoCAD SHX Text S
AutoCAD SHX Text I
AutoCAD SHX Text O
AutoCAD SHX Text I
AutoCAD SHX Text S
AutoCAD SHX Text R
AutoCAD SHX Text N
AutoCAD SHX Text O
AutoCAD SHX Text A
AutoCAD SHX Text L
AutoCAD SHX Text I
AutoCAD SHX Text S
AutoCAD SHX Text T
AutoCAD SHX Text A
AutoCAD SHX Text N
AutoCAD SHX Text G
AutoCAD SHX Text E
AutoCAD SHX Text N
AutoCAD SHX Text O
AutoCAD SHX Text L
AutoCAD SHX Text L
AutoCAD SHX Text I
AutoCAD SHX Text R
AutoCAD SHX Text N
AutoCAD SHX Text E
AutoCAD SHX Text E
AutoCAD SHX Text E
AutoCAD SHX Text N
AutoCAD SHX Text A
AutoCAD SHX Text L
AutoCAD SHX Text SECTION 232300 - REFRIGERANT PIPING 1.1 PERFORMANCE REQUIREMENTS: A. MINIMUM WORKING PRESSURES AND TEMPERATURES: UP TO 700 PSIG AT 250 DEG F 1.2 QUALITY ASSURANCE: A. COMPLY WITH ASME B31.5, REFRIGERATION PIPING & HEAT TRANSFER. B. COMPLY WITH ASHRAE 15, SAFETY CODE FOR REFRIGERATION SYSTEM. C. UL207 REFRIGERANT CONTAINING COMPONENTS AND ACCESSORIES 1.3 INSTALLATION: A. PROVIDE FILTER/DRYER ASSEMBLIES, MOISTURE INDICATORS, THERMAL EXPANSION VALVE AND SOLENOID VALVES FOR EACH REFRIGERATION CIRCUIT. B. PRESSURE TEST R-454B REFRIGERANT PIPING SYSTEM AT 535 PSIG FOR HIGH SIDE AND AT 300 PSIG FOR LOW SIDE. C. LEAK TEST REFRIGERANT PIPING WITH AN ELECTRONIC OR HALIDE LEAK DETECTOR. D. EVACUATE ENTIRE SYSTEM WITH AN APPROVED HIGH VACUUM PUMP SYSTEM TO 500 MICRONS. PART 2 - PRODUCTS 2.1 COPPER TUBE AND FITTINGS: A. COPPER TUBE: ASTM B280, TYPE ACR. B. WROUGHT-COPPER UNIONS AND FITTINGS: ASME B16.22. C. BRAZING FILLER MATERIAL: AWS A5.8. 2.2 VALVES AND SPECIALTIES: A. TO BE PER MANUFACTURER'S INSTRUCTION INCLUDING BUT NOT LIMITED TO THE FOLLOWINGS: 1. MOISTURE/LIQUID INDICATORS: 2. PERMANENT AND REPLACEABLE-CORE FILTER DRYERS: COMPLY WITH ARI 730 3. LIQUID ACCUMULATORS: COMPLY WITH ARI 495. PART 3 - EXECUTION 3.1 PIPING APPLICATIONS: A. REFRIGERANT: R-454B AND R-32. B. SUCTION LINES, HOT GAS AND LIQUID LINES FOR CONVENTIONAL AIR-CONDITIONING (COOLING ONLY) APPLICATIONS: ALL SIZES TO BE COPPER, TYPE ACR, ANNEALED-TEMPER TUBING AND WROUGHT-COPPER FITTINGS WITH BRAZED JOINTS. C. SUCTION LINES, HOT GAS AND LIQUID LINES FOR HEAT PUMP APPLICATIONS: ALL SIZES TO BE COPPER, TYPE ACR, ANNEALED-TEMPER TUBING AND WROUGHT-COPPER FITTINGS WITH BRAZED JOINTS. D. SAFETY RELIEF-VALVE DISCHARGE PIPING: COPPER, TYPE ACR, DRAWN-TEMPER TUBING AND WROUGHT-COPPER FITTINGS WITH BRAZED JOINTS. 3.2 VALVE AND SPECIALTY APPLICATION: A. INSTALL ALL VALVES AND SPECIALTIES PER MANUFACTURER'S INSTRUCTION. 3.3 PIPING INSTALLATION: A. INSTALL PIPING AS INDICATED UNLESS DEVIATIONS ARE APPROVED ON SHOP DRAWINGS. B. INSTALL REFRIGERANT PIPING ACCORDING TO ASHRAE 15. C. INSTALL PIPING IN CONCEALED LOCATIONS UNLESS OTHERWISE INDICATED AND EXCEPT IN EQUIPMENT ROOMS AND SERVICE AREAS. D. INSTALL PIPING FREE OF SAGS AND BENDS. E. WHEN BRAZING, REMOVE SOLENOID-VALVE COILS AND SIGHT GLASSES. ALSO REMOVE VALVE STEMS, SEATS, AND PACKING, AND ACCESSIBLE INTERNAL PARTS OF REFRIGERANT SPECIALTIES. DO NOT APPLY HEAT NEAR EXPANSION-VALVE BULB. 3.4 VALVE AND SPECIALTY APPLICATIONS: A. INSTALL DIAPHRAGM PACKLESS VALVES IN SUCTION AND DISCHARGE LINES OF COMPRESSOR. INSTALL DIAPHRAGM PACKLESS VALVES IN SUCTION AND DISCHARGE LINES OF COMPRESSOR. B. INSTALL SERVICE VALVES FOR GAUGE TAPS AT INLET AND OUTLET OF HOT-GAS BYPASS VALVES AND INSTALL SERVICE VALVES FOR GAUGE TAPS AT INLET AND OUTLET OF HOT-GAS BYPASS VALVES AND STRAINERS IF THEY ARE NOT AN INTEGRAL PART OF VALVES AND STRAINERS. C. INSTALL A CHECK VALVE AT THE COMPRESSOR DISCHARGE AND LIQUID ACCUMULATOR AT COMPRESSOR INSTALL A CHECK VALVE AT THE COMPRESSOR DISCHARGE AND LIQUID ACCUMULATOR AT COMPRESSOR SUCTION CONNECTION. D. EXCEPT AS OTHERWISE INDICATED, INSTALL DIAPHRAGM PACKLESS VALVES AT INLET AND OUTLET SIDE EXCEPT AS OTHERWISE INDICATED, INSTALL DIAPHRAGM PACKLESS VALVES AT INLET AND OUTLET SIDE OF FILTER DRYERS. E. INSTALL A FULL SIZE, THREE-VALVE BYPASS AROUND FILTER DRYER. INSTALL A FULL SIZE, THREE-VALVE BYPASS AROUND FILTER DRYER. F. INSTALL SOLENOID VALVES UPSTREAM FROM EACH EXPANSION VALVE AND HOT GAS BYPASS VALVE. INSTALL SOLENOID VALVES UPSTREAM FROM EACH EXPANSION VALVE AND HOT GAS BYPASS VALVE. INSTALL SOLENOID VALVES IN HORIZONTAL LINES WITH COIL AT TOP. G. INSTALL THERMOSTATIC EXPANSION VALVES AS CLOSE AS POSSIBLE TO DISTRIBUTORS ON INSTALL THERMOSTATIC EXPANSION VALVES AS CLOSE AS POSSIBLE TO DISTRIBUTORS ON EVAPORATORS. H. INSTALL MOISTURE/LIQUID INDICATORS IN LIQUID LINE AT THE INLET OF THERMOSTATIC EXPANSION INSTALL MOISTURE/LIQUID INDICATORS IN LIQUID LINE AT THE INLET OF THERMOSTATIC EXPANSION VALVE OR AT THE INLET OF EVAPORATOR COIL CAPILLARY TUBE. I. INSTALL STRAINERS UPSTREAM FROM AND ADJACENT TO SOLENOID VALVES, THERMOSTATIC EXPANSION INSTALL STRAINERS UPSTREAM FROM AND ADJACENT TO SOLENOID VALVES, THERMOSTATIC EXPANSION VALVES, HOT-GAS BYPASS VALVES AND COMPRESSORS, UNLESS THEY ARE FURNISHED AS AN INTEGRAL ASSEMBLY FOR DEVICE BEING PROTECTED. J. INSTALL FILTER DRYERS IN LIQUID LINE BETWEEN COMPRESSOR AND THERMOSTATIC EXPANSION INSTALL FILTER DRYERS IN LIQUID LINE BETWEEN COMPRESSOR AND THERMOSTATIC EXPANSION VALVE, AND IN THE SUCTION LINE AT THE COMPRESSOR. K. INSTALL RECEIVERS SIZED TO ACCOMMODATE PUMP-DOWN CHARGE. INSTALL RECEIVERS SIZED TO ACCOMMODATE PUMP-DOWN CHARGE. L. INSTALL FLEXIBLE CONNECTORS AT COMPRESSORS. 3.5 HANGERS AND SUPPORTS: A. ADJUST STEEL CLEVIS HANGERS FOR INDIVIDUAL HORIZONTAL RUNS LESS THAN 20 FEET LONG. B. INSTALL HANGERS FOR COPPER TUBING WITH FOLLOWING SPACING AND MINIMUM ROD SIZES: 1. NPS : MAXIMUM SPAN, 60 INCHES, MINIMUM ROD SIZE, INCH. 12: MAXIMUM SPAN, 60 INCHES, MINIMUM ROD SIZE, INCH. 14 INCH. 2. NPS : MAXIMUM SPAN, 60 INCHES, MINIMUM ROD SIZE, INCH. 58: MAXIMUM SPAN, 60 INCHES, MINIMUM ROD SIZE, INCH. 14 INCH. 3. NPS 1: MAXIMUM SPAN, 72 INCHES, MINIMUM ROD SIZE, INCH. 14 INCH. 4. NPS 1 : MAXIMUM SPAN, 96 INCHES, MINIMUM ROD SIZE, INCH. 14: MAXIMUM SPAN, 96 INCHES, MINIMUM ROD SIZE, INCH. 38 INCH. 5. NPS 1 : MAXIMUM SPAN, 96 INCHES, MINIMUM ROD SIZE, INCH. 12: MAXIMUM SPAN, 96 INCHES, MINIMUM ROD SIZE, INCH. 38 INCH. 6. NPS 2: MAXIMUM SPAN, 96 INCHES, MINIMUM ROD SIZE, INCH. NPS 2: MAXIMUM SPAN, 96 INCHES, MINIMUM ROD SIZE, INCH. 38 INCH. D. SUPPORT MULTI-FLOOR VERTICAL RUNS AT LEAST AT EACH FLOOR. END OF SECTION 232300
AutoCAD SHX Text
TITLE-24 PIPE INSULATION
AutoCAD SHX Text
FLUID OPERATING TEMPERATURE (°F)
AutoCAD SHX Text
INSULATION CONDUCTIVITY (BTU/HR.FT^2 °F)
AutoCAD SHX Text
INSULATION MEAN RATING TEMPERATURE (°F)
AutoCAD SHX Text
PIPE DIAMETER (IN) <1
AutoCAD SHX Text
PIPE DIAMETER (IN) 1-<1.5
AutoCAD SHX Text
PIPE DIAMETER (IN) 1.5-<4
AutoCAD SHX Text
PIPE DIAMETER (IN) 4-<8
AutoCAD SHX Text
PIPE DIAMETER (IN) 8 88
AutoCAD SHX Text
REMARKS
AutoCAD SHX Text NON-RESIDENTIAL SPACE HEATING AND SERVICE WATER HEATING (STEAM, STEAM CONDENSATE, REFRIGERANT, SPACE HEATING AND SERVICE HOT WATER)
AutoCAD SHX Text
ABOVE 350
AutoCAD SHX Text 0.32-0.34
AutoCAD SHX Text
AutoCAD SHX Text
R-VALUE: R-37 THICKNESS: 4.5"
AutoCAD SHX Text
R-VALUE: R-41 THICKNESS: 5.0"
AutoCAD SHX Text
R-VALUE: R-37 THICKNESS: 5.0"
AutoCAD SHX Text
R-VALUE: R-27 THICKNESS: 5.0"
AutoCAD SHX Text
R-VALUE: R-23 THICKNESS: 5.0"
AutoCAD SHX Text
2022 CALIFORNIA ENERGY CODE REQUIREMENTS
AutoCAD SHX Text 251-350
AutoCAD SHX Text 0.29-0.32
AutoCAD SHX Text
AutoCAD SHX Text
R-VALUE: R-24 THICKNESS: 3.0"
AutoCAD SHX Text
R-VALUE: R-34 THICKNESS: 4.0"
AutoCAD SHX Text
R-VALUE: R-35 THICKNESS: 4.5"
AutoCAD SHX Text
R-VALUE: R-26 THICKNESS: 4.5"
AutoCAD SHX Text
R-VALUE: R-22 THICKNESS: 4.5"
AutoCAD SHX Text 201-250
AutoCAD SHX Text 0.27-0.30
AutoCAD SHX Text
AutoCAD SHX Text
R-VALUE: R-21 THICKNESS: 2.5"
AutoCAD SHX Text
R-VALUE: R-20 THICKNESS: 2.5"
AutoCAD SHX Text
R-VALUE: R-17.5 THICKNESS: 2.5"
AutoCAD SHX Text
R-VALUE: R-17 THICKNESS: 3.0"
AutoCAD SHX Text
R-VALUE: R-14.5 THICKNESS: 3.0"
AutoCAD SHX Text 141-200
AutoCAD SHX Text 0.25-0.29
AutoCAD SHX Text
AutoCAD SHX Text
R-VALUE: R-11.5 THICKNESS: 1.5"
AutoCAD SHX Text
R-VALUE: R-11 THICKNESS: 1.5"
AutoCAD SHX Text
R-VALUE: R-14 THICKNESS: 2.0"
AutoCAD SHX Text
R-VALUE: R-11 THICKNESS: 2.0"
AutoCAD SHX Text
R-VALUE: R-10 THICKNESS: 2.0"
AutoCAD SHX Text 105-140
AutoCAD SHX Text 0.22-0.28
AutoCAD SHX Text
AutoCAD SHX Text
R-VALUE: R-7.7 THICKNESS: 1.0"
AutoCAD SHX Text
R-VALUE: R-12.5 THICKNESS: 1.5"
AutoCAD SHX Text
R-VALUE: R-11 THICKNESS: 1.5"
AutoCAD SHX Text
R-VALUE: R-9 THICKNESS: 1.5"
AutoCAD SHX Text
R-VALUE: R-8 THICKNESS: 1.5"
AutoCAD SHX Text
NON-RESIDENTIAL SPACE COOLING SYSTEMS (CHILLED WATER, REFRIGERANT AND BRINE)
AutoCAD SHX Text 40-60
AutoCAD SHX Text 0.21-0.27
AutoCAD SHX Text
AutoCAD SHX Text
R-VALUE: R-3.0 THICKNESS: 0.5"
AutoCAD SHX Text
R-VALUE: R-3.0 THICKNESS: 0.5"
AutoCAD SHX Text
R-VALUE: R-7 THICKNESS: 1.0"
AutoCAD SHX Text
R-VALUE: R-6 THICKNESS: 1.0"
AutoCAD SHX Text
R-VALUE: R-5 THICKNESS: 1.0"
AutoCAD SHX Text
2022 CALIFORNIA ENERGY CODE REQUIREMENTS
AutoCAD SHX Text
BELOW 40
AutoCAD SHX Text 0.20-0.26
AutoCAD SHX Text
AutoCAD SHX Text
R-VALUE: R-8.5 THICKNESS: 1.0"
AutoCAD SHX Text
R-VALUE: R-14 THICKNESS: 1.5"
AutoCAD SHX Text
R-VALUE: R-12 THICKNESS: 1.5"
AutoCAD SHX Text
R-VALUE: R-10 THICKNESS: 1.5"
AutoCAD SHX Text
R-VALUE: R-9 THICKNESS: 1.5"
SECTION 232113 - HYDRONIC PIPING 1.1 PERFORMANCE REQUIREMENTS: A. MINIMUM WORKING PRESSURES AND TEMPERATURES: 1. CONDENSATE-DRAIN PIPING: 75 DEG F. 1.2 QUALITY ASSURANCE: A. QUALITY STANDARD: ASME B31.9. 1.3 PIPING APPLICATIONS: A. CONDENSATE-DRAIN PIPING INSTALLED ABOVEGROUND TO BE ANY OF THE FOLLOWING: 1. TYPE-K DRAWN-TEMPER COPPER TUBING, WROUGHT-COPPER FITTINGS, AND SOLDERED, BRAZED AND PRESSURE SEAL JOINTS. 2. SCHEDULE 20, PVC PLASTIC PIPE AND FITTINGS AND SOLVENT-WELDED JOINTS. END OF SECTION 232113
ONLY WET SIGNED DOCUMENTS CONSTITUTE ADVANCE DESIGN
CONSULTANTS, INC. PROFESSIONAL WORK AND BECAUSE OTHER
REPRODUCIBLE DOCUMENTS MAY BE EASILY ALTERED WITHOUT THE
CONSENT OF ADVANCE DESIGN CONSULTANTS, INC., THE WET
SIGNED DOCUMENTS MUST BE REFERRED TO FOR THE ORIGINAL AND
CORRECT INFORMATION. IF THERE ANY DIFFERENCES BETWEEN THE
WET SIGNED DOCUMENTS AND ANY OTHER DOCUMENTS, THE WET
SIGNED DOCUMENTS SHALL GOVERN. ADVANCE DESIGN
CONSULTANTS, INC. IS NOT RESPONSIBLE FOR ANY MODIFICATIONS
MADE TO OUR DOCUMENTS BY ANYONE OTHER THAN AUTHORIZED
REPRESENTATIVES OF ADVANCE DESIGN CONSULTANTS, INC.
CALIFORNIA DEPARTMENT OF
VETERANS AFFAIRS
REDDING RESIDENTIAL FACILITY
ENGINEERS:
ENGINEERING STAMP:
CLIENT:
PROJECT MANAGER:
DESIGN ENGINEER:
QUALITY REVIEW:
PRINCIPAL-IN-CHARGE:
ADC PROJECT NUMBER:
CLIENT PROJECT NUMBER:
DWG. TITLE:
DRAWING SCALE:
SHEET:
PROJECT TITLE:
ATTENTION:
THIS DOCUMENT IS THE PROPERTY OF THE CLIENT. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST FOR
QUOTATION OR FOR THE PERFORMANCE OF WORK FOR THE CLIENT.
CALVET REDDING SERVER ROOM
HVAC MINISPLIT
3400 KNIGHTON ROAD
REDDING, CA 96002
V2
MECHANICAL
TITLE-24
FORMS
M-0.3
998 Park Ave.
San Jose, CA 95126
12.11.2025
12.11.2025
(408) 297-1881
M21000
(408) 297-1881
Lorenzo Rios
Advance Design Consultants, Inc.
998 Park Ave.
San Jose, CA 95126
3400 Knighton Rd, Redding, CA 96002
OFFICE OF THE STATE FIRE MARSHAL
shall be available on the project site at all times.
3/23/2026
APPROVED FIRE AND PANIC ONLY
Approval of this plan does not authorize or approve any omission or deviation from applicable regulations. Final approval is subject to field inspection. One set of approved plans
25-5700
AutoCAD SHX Text 25-081
AutoCAD SHX Text
IFR-90%
AutoCAD SHX Text 11/17/25
AutoCAD SHX Text 25-092
AutoCAD SHX Text
IFR-100%
AutoCAD SHX Text 12/15/25
AutoCAD SHX Text 25-095
AutoCAD SHX Text
OSFM SUBMISSION V1
AutoCAD SHX Text 12/22/25
AutoCAD SHX Text 25-129
AutoCAD SHX Text
OSFM SUBMISSION V2
AutoCAD SHX Text 3/17/26
AutoCAD SHX Text 25-315-20
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
LORENZO R. RIOS
AutoCAD SHX Text
AutoCAD SHX Text
AutoCAD SHX Text 03/17/26
AutoCAD SHX Text
AutoCAD SHX Text
RUDY ALANIS
AutoCAD SHX Text O
AutoCAD SHX Text
EXP. 06/30/2027
AutoCAD SHX Text
NO. M 21000
AutoCAD SHX Text F
AutoCAD SHX Text A
AutoCAD SHX Text C
AutoCAD SHX Text E
AutoCAD SHX Text T
AutoCAD SHX Text A
AutoCAD SHX Text T
AutoCAD…
This is the start of the file's text. The full file is on GovTribe.
File details come from the government source that posted it. Updated .