36E77619R0073-0004003.pdf

Project Number

Building Number

Drawing Number

Project Title

Location

Issue Date Checked Drawn

Drawing Title

Approved:

VA FORM 08 - 6231

A

CONSTRUCTION

DOCUMENTS

FULLY SPRINKLERED

Office of Construction and Facilities Management

U.S. Department of Veterans Affairs

B

C

D

E

F

A

B

C

D

E

F

21 4 5 6 7 8 9 10

Phase

ARCHITECT/ENGINEER OF RECORD STAMPCONSULTANT

321 4 5 6 7 8 9 10

AE PROJECT NUMBER: Dwg. of 78Dunham Project No: 0419950-004

I hereby certify that this plan, specification, or report was prepared by me or under my direct supervision and that I am a duly Licensed Professional Engineer under the laws of the state of Minnesota.

STAMP

I hereby certify that this plan, specification, or report was prepared by me or under my direct supervision and that I am a duly Licensed Professional Engineer under the laws of the state of Minnesota.

CONSTRUCTION DOCUMENTS

C R e v it P ro je c ts

\1

M p ls P h a rm a c y R e n o

M E

P R ja s o n g .r v t

/2

/2

:5

:4

P

M

1361-M603

MECHANICAL ELELCTRICAL

SCHEDULES

UPGRADE PHARMACY 18

MINNEAPOLIS, MN

618-16-120

06/04/2019 JG SAProject Number 47

06/04/2019

06/04/2019

EQUIPMENT

TAG APPLICATION

FAN COOLING COIL HEATING HUMIDIFIER FILTER

MANUFACTURER MODEL NUMBER MECHANICAL NOTES

NUMBER

OF FANS

MOTOR HP

(EACH) CFM

ESP

(IN)

WATER AIR SENSIBLE

CAPACITY

(MBH)

TOTAL

CAPACITY

(MBH) TYPE LBS/HR KW TYPE MERV

EFFICIENCY

PRESSURE DROP

AT 50% LOADING

(IN W.C.)

EWT

(F)

LWT

(F) GPM GLYCOL TYPE

WPD

(FT)

EAT DB

(F)

EAT WB

(F)

LAT DB

(F)

LAT WB

(F)

AC 01 BR-118B COOLING 1 1.3 1450 0.8 44 54 6.1 NA 4.3 68 57 50 49 28.6 30.4 NA 10.8 - CANISTER 11 65 0.5 LEIBERT PW011CC1 1S209HCMRBF 1,2,3,4,5,6,7,8

AC 02 BR-118 COOLING 1 1.3 900 0.8 44 54 4.3 NA 4.3 68 56 50 49 17.8 21.5 NA 10.8 - CANISTER 11 65 0.5 LEIBERT PW011CC1 1S209HCMRBF 1,2,3,4,5,6,7,8

AC 03 BR-118C COOLING 1 1.3 1750 0.8 44 54 6.3 NA 4.3 58 57 49 48.5 17,270 31.5 NA 10.8 - CANISTER 11 65 0.5 LEIBERT PW011CC1 1S209HCMRBF 1,2,3,4,5,6,7,8

EQUIPMENT

TAG HP/LOAD VOLTAGE PHASE

CALCULATED

AFC

CONTROLLER DISCONNECT AT MOTOR

PANEL CIRCUIT NUMBER CONDUIT/FEEDER SIZE ELECTRICAL NOTESTYPE

FURNISHED BY/

INSTALLED BY LOCATION CTRL WIRE BY AMPS/TYPE

FUSE SIZE

(AMPS) NEMA TYPE

FURNISHED BY/

INSTALLED BY LOCATION

AC 01 7.6 FLA 480 V 3 - CP MANUFACTURER INTEGRAL MANUFACTURER 15/CB N/A 1 DIV 26/DIV 26 AT UNIT EHBM3-1 31,33,35 3/4"C. (3)#12, (1)#12G 1

AC 02 7.6 FLA 480 V 3 - CP MANUFACTURER INTEGRAL MANUFACTURER 15/CB N/A 1 DIV 26/DIV 26 AT UNIT EHBM3-1 31,33,35 3/4"C. (3)#12, (1)#12G 1

AC 03 7.6 FLA 480 V 3 - CP MANUFACTURER INTEGRAL MANUFACTURER 15/CB N/A 1 DIV 26/DIV 26 AT UNIT EHBM3-1 31,33,35 3/4"C. (3)#12, (1)#12G 1

MECHANICAL NOTES:

1. PROVIDE WITH UPFLOW DISCHARGE PLENUM WITH DUCT COLLAR.

2. PROVIDE WITH REAR RETURN FLOORSTAND.

3. PROVIDE WITH 2-WAY CONTROL VALVE AND ALL VENT/DRAIN, ISOLATION VALVES, STRAINERS, AND CIRCUIT SETTER FOR BALANCING PURPOSES.

4. PROVIDE WITH TWO SETS OF 2" PLEATED MERV 11 FILTERS. COORIDNATE STOARGE OF REPLACEMENT SET OF FILTERS WITH VA FACILITIES.

5. PROVIDE LIEBERT ICOM CONTROLLER MOUNTED DIRECTLY TO FRONT OF UNIT. INCLUDE BACNET NETWORK CARD FOR FULL INTEGRATION INTO EXISTING BUILDING AUTOMATION SYSTEM.

6. PROVIDE CONDENATE PUMP. ROUTE ALL CONDENSATE TO NEAREST FLOOR DRAIN OR SINK. INCLUDE CABLE TYPE LEAK DETECTION AROUND FLOOR DRAIN AND WIRE ALARM NOTIFICATION INTO BUILDING AUTOMATION AND LOCAL AUDIBLE ALARM.

7. PROVIDE BOTH HIGH TEMP AND SMOKE DETECORS WITHIN UNIT. WIRE BOTH ALARM NOTRIFICATION INTO BUILDING AUTOMATION SYSTEM.

8. PROVIDE WITH LARGE COMMUNICATION DISPLAY.

9. MANUFACURER TO SEND TECHNICIAN ON-SITE FOR FACTORY START-UP, VA FACILITY TRAINING, AND PERFORMANCE TESTING.

COMPUTER ROOM AIR CONDITIONING UNIT SCHEDULE - CHILLED WATER

GENERAL ELECTRICAL NOTES:

A. WHEN THE CONTROLLER TYPE IS A VFD OR MAGNETIC STARTER, REFER TO THE VARIABLE FREQUENCY

DRIVE CONTROLLER

SCHEDULE OR THE MAGNETIC STARTER SCHEDULE FOR MORE INFORMATION.

B. MECHANICAL EQUIPMENT AND CORRESPONDING ELECTRICAL DISCONNECTS/CONTROLLERS SHALL HAVE A

STANDARD SHORT-

CIRCUIT CURRENT RATING HIGHER THAN THE CALCULATED VALUE SHOWN IN THE SCHEDULE.

MECHANICAL (238123)

ELECTRICAL

ELECTRICAL NOTES:

CONTROLLER TYPES:

MMS - MANUAL MOTOR STARTER (WITH OVERLOADS)

CP - CONTROL PANEL

MAGS - MAGNETIC STARTER

MRS/MS - MOTOR RATED SWITCH (WITHOUT

OVERLOADS)

A. REFER TO CALCULATED AVAILABLE FAULT CURRENT COLUMN IN THE ELECTRICAL SCHEDULE BELOW FOR MINIMUM

REQUIRED AVAILABLE FAULT CURRENT (AFC) FOR SCHEDULED MANUFACTURER.

GENERAL MECHANICAL NOTES:

EQUIPMENT TAG APPLICATION TYPE CFM ESP (IN W.C.) BHP FAN RPM

DRIVE

TYPE SONES

VFD

(YES/NO) MANUFACTURER MODEL NUMBER MECHANICAL NOTES

70.EF BR118C.1 BR-118C - TYPE A2 HOOD UTILITY 1400 1.5" 0.76 2809 BELT 16.5 NO GREENHECK 10 USF-300 2,3,4,5

70.EF BR118C.2 BR-118C - TYPE B2 HOOD UTILITY 800 3.5" 0.9 2809 BELT 16.5 NO GREENHECK 08 USF-300 2,3,4,5

EF 146 BR-119 - TYPE B2 HOOD UTILITY 600 3.0" EXISTING NOTE 1 BELT EXISTING NO EXISTING EXISTING 1

EQUIPMENT

TAG HP/LOAD VOLTAGE PHASE

CALCULATED

AFC

CONTROLLER DISCONNECT AT MOTOR

PANEL

CIRCUIT

NUMBER CONDUIT/FEEDER SIZE

ELECTRICAL

NOTESTYPE

FURNISHED BY/

INSTALLED BY LOCATION CTRL WIRE BY AMPS/TYPE

FUSE SIZE

(AMPS) NEMA TYPE

FURNISHED

BY/ INSTALLED

BY LOCATION

70.EF

BR118C.1

1 HP 480 V 3 - STARTER DIV 26/DIV 26 AT UNIT DIV 26 15/CB N/A 1 DIV 26/DIV 26 AT UNIT EDP-NC 14,16,18 3/4"C. (3)#12, (1)#12G

70.EF

BR118C.2

1 HP 480 V 3 - STARTER DIV 26/DIV 26 AT UNIT DIV 26 15/CB N/A 1 DIV 26/DIV 26 AT UNIT EDP-NC 13,15,17 3/4"C. (3)#12, (1)#12G

MECHANICAL NOTES:

1. REPLACE EXISTING FAN SHEAVE, DRIVE AND BELT AS REQUIRED TO ATTAIN SCHEDULED CFM.

2. CONTRACTOR TO RESHEAVE AND BALANCE UNIT ON SITE. NOTE THAT AIRFLOWS LISTED MAY BE FOR FUTURE VOLUME REQUIREMENTS AND COULD REQUIRE SIGNIFICANTLY LESS AIRFLOW BASED ON FINAL BSC HOOD SELECTION.

3. PROVIDE EACH NEW EXHAUST FAN WITH VFD FOR BALANCING PURPOSES. NO ISOLATION DAMPERS SHALL BE ALLOWED WITHIN HARZARDOUS EXHAUST DUCTWORK.

4. PROVIDE CONCRETE EQUIPMENT PAD AND SPRING TYPE VIBRATION ISOLATORS FOR EACH NEW EXHAUST FAN.

5. PROVIDE EACH FAN SCROLL WITH WELDED CONSTRUCTION AND HEAVY EPOXY COATING FOR CORROSION PROTECTION. ROUTE DISCHARGE DUCT UP THROUGH PENTHOUSE ROOF WITH DRAIN FOR WATER INFIILTRATION.

FAN SCHEDULE

GENERAL ELECTRICAL NOTES:

A. WHEN THE CONTROLLER TYPE IS A VFD OR MAGNETIC STARTER, REFER TO THE VARIABLE FREQUENCY

DRIVE CONTROLLER

SCHEDULE OR THE MAGNETIC STARTER SCHEDULE FOR MORE INFORMATION.

B. MECHANICAL EQUIPMENT AND CORRESPONDING ELECTRICAL DISCONNECTS/CONTROLLERS SHALL HAVE A

STANDARD SHORT-

CIRCUIT CURRENT RATING HIGHER THAN THE CALCULATED VALUE SHOWN IN THE SCHEDULE.

MECHANICAL (233413, 233416, 233423)

ELECTRICAL

ELECTRICAL NOTES:

CONTROLLER TYPES:

VFD - VARIABLE FREQUENCY MOTOR CONTROLLER

MMS - MANUAL MOTOR STARTER (WITH OVERLOADS)

CP - CONTROL PANEL

MAGS - MAGNETIC STARTER

MRS/MS - MOTOR RATED SWITCH (WITHOUT OVERLOADS)

MAGS - MAGNETIC STARTER

MRS/MS - MOTOR RATED SWITCH (WITHOUT OVERLOADS)

A. REFER TO CALCULATED AVAILABLE FAULT CURRENT COLUMN IN THE ELECTRICAL SCHEDULE BELOW FOR MINIMUM

REQUIRED AVAILABLE FAULT CURRENT (AFC) FOR SCHEDULED MANUFACTURER.

GENERAL MECHANICAL NOTES:

Signature

Name

Date

Registration Number

Jason R. Gottwalt, P.E.

41360

Signature

Name

Date

Registration Number

Curtis D. Barlage, P.E.

45914

Revisions: Date:

Revision 1 Date 1