34101-13791_Fence-Gate_Installation_Gordonsville_-Scope.pdf
PDF 160 KB Posted
- Attached to
- Fence-Gate Installation - Gordonsville - UPDATED
- Solicitation number
- Event 34101-13791
- Issued by
- Tennessee
About this file
This is a Scope of Work document from the State of Tennessee, Military Department, for Sourcing Event 34101-13791, which involves the installation of a new fence and gate system at the Army National Guard facility in Gordonsville, Tennessee. The project requires the contractor to provide all labor, materials, and equipment for the complete installation. The scope includes approximately 476 linear feet of 7-foot tall Ameristar Impasse II security fencing (or approved equal) with three-rail design and black Perma-Coat finish; one 24-linear-foot security gate with steel V-track roll design and two bollard posts; one 3-foot opening single swing gate; approximately 198 linear feet of 6-foot tall galvanized chain link fence with three strands of barbed wire; two dual-height gooseneck access control stands with cameras compatible with the existing AIPHONE system; and one Hy-Security SlideDriver 15 heavy-duty gate operator (or approved equal). All attendance at the mandatory site visit is required for bid submission. The project manager is Jerry Carroll (615-519-4783, jerry.carroll@tn.gov).
The bid price shall be all-inclusive of materials, equipment, and labor, with the contractor responsible for all measurements and verification of existing conditions and underground utilities. The contractor must submit specification sheets at the time of bid for any approved equal products being proposed. Installation requirements include concrete foundations for all posts with minimum 36-inch embedment for security fence posts, electrical installation from the nearest service panel with fiberglass/HDPE or PVC conduit, data communication conduit from the existing AIPHONE master station, and as-built documentation in PDF format. If communication distances exceed 300 feet, the contractor is responsible for procuring and installing necessary equipment such as repeaters. The security fence and gates include a 15-year Perma-Coat warranty, and all conduits must be bored under concrete or asphalt surfaces to maintain site aesthetics and prevent tampering.
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
State of Tennessee Sourcing Event 34101-13791
Event 34101-13791 Page 1 of 3
The State of Tennessee, Military Department is seeking procurement for installing a new fence and gates for this location shown below, per this Scope of Work.
Project Manager: Jerry Carroll Telephone Number: 615-519-4783 E-Mail Address: jerry.carroll@tn.gov
Facility: Army National Guard Gordonsville, TN 101 Transport Drive, Gordonsville, TN 38563
Mandatory Site Visit – All bidders are required to attend the mandatory site visit in person, in order to submit a bid response.
The Contractor shall provide all labor, materials and equipment to complete job as specified below. Bid Price shall include all materials, equipment, and labor. It’s the responsibility of the Contractor for all measurements; the State will not pay any additional cost due to error in measurements.
Security Fence Approved Model – Ameristar Impasse II – Gauntlet Style or written approved equal, must provide spec sheets at time of bid if another manufactured is used.
- Install approximately 476 LF of 7’ tall security
- Three-rail design
- 2.75” wide Pales
- 11 ga rails
- 12 ga I beam posts,
- Line post to be on 8’ centers, all posts set in concrete, minimum embed 36”
- Black “Perma-Coat” finish with 15-year warranty.
- All posts shall be set in concrete.
Security Gates – total of 1 Approved Model – Ameristar Passport IS – Gauntlet Style or approved equal, must provide spec sheet at time of bid if another manufacturer is used.
- Install (1) 24 LF 7’ tall security gate with steel V-Track roll gate design, 4” gate posts
- Gate to have (2) 6.625” schedule 40 weight bollard posts with yellow bollard sleeve covers for protection, a total of 4 bollard posts.
- Three-rail design
- Black “Perma-Coat” finish with 15-year warranty
- Install (1) single swing gate 3’ opening, 3” gate posts, Shut-it original B.A weld on hinges
Event 34101-13791 Page 2 of 3 with strong arm latch.
- All posts shall be set in concrete.
Chain Link Fence
- Install approximately 198 LF of 6’ tall with galvanized chain link fence
- with (3) strands of barbed wire, 12.5-gauge, 4-point barbs, max 5” o.c.
- 9-gauge fabric with 2” chain link mesh
- 3" WT/LG40 corner, end and pull posts.
- 2" WT/LG40 weight line posts,
- 1-5/8" diameter, 40-weight, top rail
- 7-gauge bottom tension wire.
- Line post to be on 10’ centers, all posts set in concrete
- Tie in new fencing to existing chain link fence post using all new mechanical ties and new barbed wire as needed.
- Selvages: Top and Bottom selvage twisted.
Access Controls
- Shall be compatible with existing AIPHONE system and tie in.
- (2) dual height gooseneck-stand with two access control pads with AI - IX-DV cameras
- Minimum 18” diameter concrete pad, embedded 24” in the ground, for gooseneck stand
- Shall install a (120v or 240v) single phase circuit, from the nearest service panel in the facility to the gate operator with 1” fiberglass/HDPE or PVC conduit with pull string
- Shall install 1” fiberglass/HDPE or PVC conduit for data communication from existing
AIPHONE master station IX-MV system to the access control pad/camera and operator with pull string
- Shall fully integrate the existing system with new components; test & verify proper operation of controls
- (2) protective 6” steel pipe bollards (at each dual height gooseneck), concrete filled, painted safety yellow, embedded 3’ in the ground in minimum 12’diameter hole with concrete. Shall extend 48” above grade and be plumb in all directions
- Conduits shall be bored under any concrete or asphalt surfaces.
- Communication Distance – In the event that the communication distances exceed 300’, it’s the responsibility of the installation Contractor to install the necessary equipment (i.e. repeater) to ensure the equipment operates correctly. As well, the Contractor must submit documentation at the end of the project that notes installation of the equipment on an “As-built” drawing in a PDF format.
Heavy Duty Gate Operators
Approved Model – Hy Security SlideDriver 15 for gates less than 1500lb or approved equal, Event 34101-13791 Page 3 of 3 must provide spec sheet at time of bid if another manufacturer is used.
- 18” minimum concrete pad thickness, minimum 8” embedded in the ground
- All conduits set in concrete pad and concealed by the operator to prevent tampering
- Install a (120v or 240v) single phase circuit, from the nearest service panel in the facility to the gate operator with 1” fiberglass/HDPE or PVC conduit with pull string
- Install 1” fiberglass/HDPE or PVC conduit for data communication from existing
AIPHONE system to the access control pad/camera and operator with pull string
- (1) free egress detector loop, cut in existing asphalt pavement
- (1) reversing detector loop, cut in existing asphalt pavement
- Accessories to be installed o Internal solenoid lock kit o Fire & Emergency Access Lock Box (with manual release) and Click2enter.
Alternatives to Ameristar Impasse II Fence and Gates – if the vendor determines they can supply an alternative to the Ameristar brand fencing, it is the responsibly of the vendor to provide documentation at time of bid that the compares the options with notes and specs sheets, easily showing the product is superior to Ameristar Impasse II.
Contractor to verify all measurements and any underground utilities before digging on site
File details come from the government source that posted it. Updated .