20008-26-BRMA-FURN-REPOST-1.pdf

ADDENDUM NO. 1

August 12, 2026

PROJECT: Baton Rouge Metropolitan Airport – Terminal Furniture 9430 Jackie Cochran Drive Baton Rouge, LA 70807

ARCHITECT: Washer Hill Lipscomb Cabaniss Architecture (LA) LLC, WHLC Architecture 1744 Oakdale Drive Baton Rouge, LA 70810

Incorporate in the plans and the project manual the following additions, deletions, changes and clarifications. Each item shall be governed by the conditions set forth in Division 1 General Requirements of this Project Manual and the specific conditions set forth in the sections of the specifications pertaining to the item:

ADDENDUM NO. 1

Total Pages: 8 - (8 ½” x 11”) including Title Sheet 2 - (24” x 36”)

SPECIFICATIONS

DIVISION 12 FURNISHINGS

Section 12 25 00 FURNISHINGS

Attached spec section to Replace previously issued section. Clarifications noted in red.

3 pages ( 8-1/2” x 11”)

FURNITURE SPECIFICATIONS

Attached spec section to Replace previously issued section. Finish clarifications noted in red.

5 pages ( 8-1/2” x 11”)

DRAWINGS

Sheet PH1.2 + PH2.3: See attached revised sheet. 2 pages (24”x36”). Clarification: Phasing Plans revised to (2) installs and phases.

Phasing Plan Sheet PH2.4 Deleted.

Furnishings

12 52 00-1

SECTION 12 52 00

FURNISHINGS

PART 1 GENERAL

1.01 SUMMARY

A. Provide furniture shown on the Drawings, as specified herein, and as needed for a complete and proper installation.

B. Related work:

1. Refer to drawing for locations of furniture, furnishings, equipment, and power locations corresponding with item codes.

2. Refer to the following Furniture, Furnishings and Equipment

Specification Forms for each item code found on Drawings.

1.02 QUALITY ASSURANCE

A. Use adequate numbers of skilled workmen thoroughly trained and experienced in the necessary crafts and completely familiar with the specified requirements and methods needed for proper performance of the work of this Section.

B. It is imperative that the Owner receives the finest possible quality. As a result, these performance requirements should be considered a minimum.

All equipment must be equal to, or higher than the standard defined. The

Owner shall be the sole judge of equivalency. All Bidders must comply so that the Owner is assured that all bids are on the same basis. Any

Bidder found to be in default of any of these requirements shall be deemed to be non-responsive to the specifications. An award will not be made to a non-responsive bid. All Bidders must submit with their bid a statement that their proposal complies with all of the requirements set forth in these specifications. In addition, a product mock-up, installed on site, must be submitted for review.

C. Participating manufacturers must demonstrate no less than 10 years of production experience with published literature clearly indicating general compliance of products with requirements of this section.

1.03 SUBMITTALS

A. Product Data: For each type of product

1. Include construction details, material descriptions, dimensions of components, and finishes

B. Samples for selections if not already specified below for each type of exposed color, finish, texture, and pattern indicated.

1. Include samples of accessories involving color and finish selection.

12 52 00-2

C. Product Certifications including BABA (Buy America, Build America) certification if applicable.

D. Material Certificates: for each type of flame-retardant treatment of upholstery fabric

E. Warranty information

1.04 CLOSE OUT SUBMITTALS

A. Operation and Maintenance Data:

a. Maintenance of seat mechanism and other operating components.

b. Methodes for maintaining upholstery fabric.

c. Precautions for cleaning materials and methods that could be detrimental to seating finishes and performance.

1.05 WARRANTY

A. Manufacturer agrees to repair or replace components that fail in materials or workmanship within specified warranty period.

1. Failures include, but not limited to the following:

a. Structural failures including standards, beams, and pedestals.

b. Faulty operation of self-rising seat mechanism

c. Faulty operation of electrical components.

d. Wear and deterioration of fabrics and sticking beyond normal use.

e. Deterioration of metals, metal finishes, and other materials beyond normal weathering and use.

B. This warranty shall be in addition to and not a limitation of other rights the Owner may have against the Dealer under the Contract documents.

The warranty periods detailed below will be effective after the date of substantial completion of the project installation.

1. Structural Warranty: 25-Years Minimum

2. Upholstery Warranty: 3-5 Years dependent on specified material

3. Table Materials: 10-Years Minimum

4. Power Warranty: 10-Years Casing / 2-Years Componentry

1.06 DELIVERY, STORAGE, AND HANDLING

A. Make specific arrangements with furniture suppliers to provide clear plastic sheet full covering on each item, and to provide heavy-duty shipping crates as required for proper protection during shipping and handling.

B. Storage of any items shall be the sole responsibility of the vendor and will not be provided any on site storage.

C. Dealer shall be responsible for offsite delivery, storage and handling of all furniture. Furniture shall be preassembled offsite and delivered per phasing plans. Refer to schedule for anticipated install dates.

PART 2 PRODUCTS

12 52 00-3

2.01 FURNITURE

A. Provide the following items, in the quantities indicated, and according to the following Furniture, Furnishings and Equipment Specification

Forms. See individual sheets that follow at the end of this specification.

B. Apply Owner provided “property tags”, if required, to all furniture as specified prior to completion of the installation.

1. Labels - Locate “property tags” on a concealed surface or where required for observation after installation, on an accessible surface that is not conspicuous.

2.02 BASIS OF DESIGN FOR TERMINAL BEAM SEATING SYSTEM

A. The design should offer a system of homogeneous elements in a variety of finishes for ultimate flexibility. The system should include: seat, back, beam, double arm spacing, leg, and reversible tables where and if applicable.

B. The design should facilitate virtually unlimited permutations – back to back seating, continuous rows arranged in configurations of seats and tables if applicable. It should be possible to introduce tables at any point, replacing a seat according to layout requirements.

C. The seats, backs and benches should be available with upholstery mounted on a steel seat structure or suspended molded soft feel polyurethane. If particular requirements demand other combinations the system should be able to be customized.

D. Ease of cleaning is important, the seat and back junction should have a gap of to allow spilt liquid and garbage to fall through for easy cleaning. If beams are provided as the supporting structure they should have no flat surface so to avoid dust and dirt accumulation.

E. Both Seating product and Power Product should offer future-proof protection to the airport in respect of reconfigurability and updatability.

F. Airport Designed and Certified Power Modules (Double Arm Positioning)

G. Provide at least (two) or recommended quantity per manufacturer: Transportation trolley’s allowing single person operation, manual lifting is not acceptable on the basis of health and safety.

H. Back-to-Back Spacer Bars, Available for maintaining the correct distance between seat rows when placed back to back.

I. ADA / PRM / WC full compliancy

Subject to compliance requirements, basis of design for seating system is:

A. Zoeftig Ltd, Kings Hill Industrial Estate, Bude, Cornwall, United Kingdom EX23 8QN.

12 52 00-4 email: sales@zoeftig.com web: www.zoeftig.com

Martin Sharp Senior Regional Director msharp@zoeftig.com UK Cell:44 0 7525 128466

2.03 STANDARD COMPONENTS

A. Supporting Beams: Fabricated from 3” diameter x 10 SWG mild steel tube. Wall thickness tolerance 3.01 mm - 3.06 mm. The beam system should include an integral leveling system whereby it can be leveled for uneven floors within the beam therefore avoiding the need for adjustable glides. The leveling of the system should not involve lifting the beam, adjustment should be semi-automatic. Beam ends should be capped, using caps manufactured from machined solid aluminum billet, highly polished, secured to end of beam by anti tamper socket grub screws.

B. Seat & Back Forms (Panels): Formed to shape using CR1 cold rolled mild steel sheet 10

AWG/0.098 inch (2.5mm) thick. Seat and back forms to be supported by mild steel profiled supports. Forms should be ergonomically shaped, the profile should also be of a design that helps prevent the user from sliding forward out of the seat.

C. Aluminum Parts:

LM6/M

Tensile strength (N/MM2)

Elongation: 13%

Brinall hardness: 60

D. Paint,:

Powder coat thickness: 50-70 microns

Lacquer thickness: 50-70 microns

Overall thickness: 100-140 microns

Gross % (after power coating and lacquer): 105-120%

E. Foam: Pressure reducing seat cushion in response to growing demand for a remedy to combat problems associated with sitting for lengthy periods of time. Foam/Cushion design should help prevent circulatory pressures which can cause discomfort. Foam should comprise of two distinct layers which carry out different but equally important functions. The upper layer should form to the body's shape. The supporting layer should improve support and flexibility for the upper layer. Seat cushion to be fully supported by seat and back steel panels/forms, suspended seat cushions are not acceptable.

Density of foam cushion to be a combination of CMF60F and Reflex650F. All foams to be X rated for continuous use as per ISO 3385 1989. (CM = Combustion Modified/Fire retardant, Reflex = Fire retardant memory foam, X = Extremely severe)

F. Upholstery:

(1) Unit shall have separate seat and back cushions

(2) Cushions must be easily removable in the field for ease of re-upholstery

(3) Manufacturer must supply seat and back cushions for replacement fabric

(vinyl)

(4) PVC Vinyl: Refer to Fabric Legend for information.

(5) Re-upholstery should require no specialist tools or knowledge other than those used by an experienced furniture upholsterer.

(6) Injection molded high-density nylon upholstery trims should be fitted to

12 52 00-5 protect the top of the back and front of the seat from impact damage of trolleys, suit cases and carry-on’s etc.

G. Arm rests shall be provided at ends of each unit and between each seat, unless otherwise noted. Arms shall be removable in the field for ease of retrofit. Arms to be cast aluminum polished to a high standard with close tolerance machined housings which should mount to the beam by clamping both inside and outside of the beam, direct fixing to the beam without a clamping system is not acceptable.

J. Dimensions: Seat Size:

Width: 24” (600 mm) on centers

Depth: 25.5” (650 mm)

Height: 33” (835 mm)

Weight per seat place (based on a 4 seat beam): 4- 55lb (25 kg)

J. Support feet or bases

(1) Feet/Base to be cast aluminum polished to a high standard with close tolerance machined housings which should mount to the beam by clamping both inside and outside of the beam, direct fixing to the beam without a clamping system is not acceptable. Foot should be fitted with nylon toe to help prevent damage to floor.

(2) Base must not protrude beyond the units of the seat back or the front seat edge into aisle widths

K. Table unit

(1) Composed of ½” (13mm) solid laminate with bullnose edge, decorative finish to top and bottom surface.

(2) Size 23” X 23” (585mm X 585mm)

(3) Attached to steel beam bracket, through bolted with flat cap on table top, balancer should be of same finish to enable reversing of the table top in the future.

2.04 STRENGTH RATING

A. Certified to ISO EN12727 Level 4 Severe Contract Use.

B. Or certified as tested to the following:

1. Seat shall be tested and professionally certified through an

2. independent testing laboratory to support and withstand a worst case positional static load of 450lb (200kg), cycled 10 times without failure or irregularities that would impair usefulness.

3. Seat shall be tested and professionally certified to withstand

4. 10 vertical impacts of a 55lb (25kg) impactor from 12” (300mm) onto a point most likely to cause failure. i.e.front corner of seat.

5. Seat durability shall be tested and certified to withstand a load of 200lb (90kg) applied vertically down onto the seat 200,000 times.

6. Back shall withstand a front or rear static load of 165lb (75kg) applied horizontally, cycled 10 times at a position 4” (100mm) from the top edge of the back. And a 200lb (90kg) for applied vertically cycled 10 times on the top edge of the back.

7. Back shall be tested and professionally certified to withstand,

8. without failure, 10 swinging impacts to the rear of the back by 20lb (8.5kg) x 40”

12 52 00-6

(1 meter) pendulum striker from an angle of 68 degrees.

9. Back durability shall be tested and certified to withstand a load of 73lb (33kg) applied horizontally to the front of the back rest 200,000 times.

10. Armrests shall be tested and professionally certified to withstand, without failure, a 200 lb.(90kg) static load applied both perpendicular to and vertically down on the arm.

11. Armrests shall be tested and certified to withstand an impact of 20lb (8.5kg) x

40” (1 meter) pendulum striker from an angle of 68 degrees.

PART 3 EXECUTION

3.01 EXAMINATION

A. Examine floor, walls, and other adjacent work and conditions with Installer present for compliance with requirements and other conditions affecting performance of work.

B. Verify that electrical connections are properly located.

C. Proceed with installation only after unsatisfactory conditions have been corrected.

D. Upon receiving furniture shipment, dealer to inspect for any defects, damages, or missing items. Any damage or missing items are to be reported immediately.

3.02 SCHEDULE

A. Timeline: the installation of furniture is based on the completion date of the Baton

Rouge Terminal Interiors Upgrades project. Furniture should be installed upon completion of each individual phase. Refer to phasing plans for number of installs.

B. Vendor to work in conjunction with Awarded Contractor of the Baton Rouge Terminal

Interior Upgrades project to finalize scheduling.

C. All furniture is to be ordered as one package. Dealer is responsible for storage of all furniture for the duration of the project.

D. Anticipated install schedule per phase:

1. Phase 1 Install Date: February 8, 2027-February 22, 2027

• Refer to phasing plans for all furniture included in

Phase 1

2. Phase 2 Install Date: July 12, 2027-July 30th, 2027

• Refer to phasing plans for all furniture included in

Phase 2

3.03 DELIVERY AND INSTALLATION

A. Remove and dispose of existing furniture as required.

B. See drawings for locations and layout of all furniture items.

C. Provide furniture and install per phasing plans.

D. Vendor shall be responsible for any storage fees.

12 52 00-7

E. Installation to be performed by experienced and trained mechanics have a minimum of three (3) years’ experience doing similar installations.

F. Installer and/or any personnel involved in the installation must be able to pass required airport background checks. Vendor is responsible for any payment associated with background checks and obtaining badge access.

Refer to airport safety documents.

G. When designated spaces are ready, as determined by the Architect, carefully uncrate each item remove all protective material and place it in its designated location. All furniture shall be preassembled at (dealer responsible) offsite location to minimize disruption of the Airport. No staging area for assembly of furniture will be provided onsite.

H. Bolted Furniture, where indicated per specifications, installer shall be responsible for bolting furniture to the floor.

I. Modular furniture, properly secure all modular furniture with ganging brackets and hardware per manufacturer's instructions. Configurations to match furniture layouts per plan.

J. Hours of installation may vary depending on flight schedules. Refer to

Summery section 01 10 00.

K. Upon completion of the installation, touchup all scratches and abrasions to be completely invisible to the unaided eye to the approval of the

Architect.

L. Promptly remove from the job site all crates and other packing material derived from items furnished under this Section. Vendor responsible for removing and disposing of all boxes, trash, and any other debris.

M. Job Protection: make all reasonable efforts to protect finished building surfaces, carpet and access area. Should damage occur, immediately cover the expenses of all repairs or replacements necessary to the approval of the Owner or Architect. Use every means possible to protect installed materials both during and after installation.

3.04 PUNCHLIST

A. Punch list required. Vendor to walk and review items per plan with both architect and owner. All punch list items to be taken care of by vendor in a timely manner. Appropriate funds will be withheld at the owner discrepancy per the natural of damaged or unfinished item.

12 52 00-8

END OF SECTION

T S T S

BAGGAGE

CLAIM

TICKET

COUNTERS

VESTIBULE

VESTIBULE

VESTIBULE

VESTIBULE

VESTIBULE

CAR RENTAL

CONCOURSE B-

LEVEL 1

UNITED AMERICANDELTA (T)

ENTERPRISE

NATIONAL (T)

DOLLAR

HERTZ (T)

BUDGET

AVIS (T)

phasing symbol legend scope not in contract (N.I.C.)

shading indicates areas of work contractor shall submit final phasing plans with construction schedule durations for each phase for the owner's review prior to demolition and construction.

contractor shall hold preconstruction phasing coordination meeting(s) with owner, architect, and all vendors prior to demolition and construction.

contractor shall hold weekly phasing meetings with the architect and owner for the duration of the work.

phasing general notes

1A phase number washer hill lipscomb cabaniss architecture, llc copyright 2023

1744 oakdale dr

t. 225.767.1530 baton rouge, la

f. 225.767.0018 w w w . w h l c a r c h i t e c t u r e . c o m

23-027A

06.04.2026

B A

T O

N R

O U

G E T

E R

M

IN

A L F

U R

N

IT

U R

E

J a c k ie C o c h ra n D r.

B a to n R o u g e

L

A

FURNITURE BID

LEVEL 1 - FURNITURE

PHASING PLANS

B a to n

R o u g e M e tr o p o li ta n

A ir p o rt

PH1.2

SCALE 1" = 50'-0"

1 LEVEL 1 - PHASE 1 FURN

ADDENDUM #01 08.10.2026

NOT USED

NOT USED

phasing symbol legend scope not in contract (N.I.C.)

shading indicates areas of work contractor shall submit final phasing plans with construction schedule durations for each phase for the owner's review prior to demolition and construction.

contractor shall hold preconstruction phasing coordination meeting(s) with owner, architect, and all vendors prior to demolition and construction.

contractor shall hold weekly phasing meetings with the architect and owner for the duration of the work.

phasing general notes

1A phase number temporary removeable partition to be provided by the contractor & kept by the owner re: specifications shading indicates areas of work to take place after hours

CONCOURSE B

B2

B1

B3

C O

N C

O U

RSE A

A

A

TSA

ROTUNDA

G201

PEDESTRIAN

BRIDGE

A

A

PARKING

STRUCTURE

LOBBY

D

ELTA

(T

U N

IT

ED

AMERICAN

AMERICAN

CONCOURSE B

B2

B1

B3

C O

N C

O U

RSE A

TSA

ROTUNDA

G201

PEDESTRIAN

BRIDGE

PARKING

STRUCTURE

LOBBY

A

A

A4

A3

D

ELTA

U N

IT

ED

(T

AMERICAN

AMERICAN

washer hill lipscomb cabaniss architecture, llc copyright 2023

1744 oakdale dr

t. 225.767.1530 baton rouge, la

f. 225.767.0018 w w w . w h l c a r c h i t e c t u r e . c o m

23-027A

06.04.2026

B A

T O

N R

O U

G E T

E R

M

IN

A L F

U R

N

IT

U R

E

J a c k ie C o c h ra n D r.

B a to n R o u g e

L

A

FURNITURE BID

LEVEL 2 - FURNITURE

PHASING PLANS

B a to n

R o u g e M e tr o p o li ta n

A ir p o rt

PH2.3SCALE 1" = 50'-0"

1 LEVEL 2 - PHASE 1 FURNITURE

SCALE 1" = 50'-0"

2 LEVEL 2 - PHASE 2 FURNITURE

ADDENDUM #01 08.10.2026

ITEM DESCRIPTION:

PHOTOS/ SAMPLES:

ITEM CODE:

FINISH: NOTES:

UPHOLSTERY FINISH:

Diameter: Length: Width: Height: Seat Height: Arm Height:Depth:

Item:

Manufacturer Basis of Design:

Product:

Mfg. Model No:

Description:

Location:

Quantity:

Double Sided Tandem Seating, Config D Zoeftig Vista Configuration D

Double sided tandem seating with tables and tablet arms n/a

Metal Color: Black Finish Solid Surface Arm Caps: Durasein, Glacier Tundra, PM4872 Solid Surface: Durasein, Glacier Tundra, PM4872

11’-6” 24” 57” 33” 16” 26”

- 8 Seats

- 4 Tablet Arms

- 1 Full width table

- 2 Half width table

- 8 Arm

- 3 leg

- Powered, No USB

- 4 B2b Infill

FABRIC: F-6

SS-1

Rotunda

13Vista by Zoeftig

Upholstery: PVC Tomato 554285

Fire Red 554311

Melon 554361

Empire Green 554314

Quartz 554330

Royal Blue 554292

Mauve 554367

Persimmon 554303

Lox 554348

Chocolate 554318

Lime 554326

Mint Julep 554313

Blueberry 554286

Rosewood 554908

Nasturtium 554293

Indian Red 554289

Allspice 554304

Citrus 554122

Bluejay 554284

Colonial Blue 554346

Natural 554329

Marigold 554301

Melba 554365

Oak Brown 554363

Ocean Grey 554332

Marina 554283

Coal 554328

Black 554290

Saffron Silk 554294

Port 554351

Saddle Tan 554309

Moon Glow 554310

Bright Blue 554121

Cadet 554353

Slate 554316

Lemon Peel 554308

Deep Clay 554288

Camel 554305

Spruce 554325

Phoenician 554350

Fjord 554344

Grey 554358

Wheat 554327

Russet 554297

Rum Sherbert 554334

Jade 554317

Sky 554347

Expresso 554333

Light Grey 554331

New Burgundy 554287

Burnt Orange 554299

Ceylon Ivory 554334

Turk 554295

Light Blue 554123

Grape 554302

Glacier 554366

Wine 554307

Brandy 554336

Hunter Green 554296

Light Teal 554300

Cerulean 554349

Purple Iris 554291

White 554306

Candy Apple 554298

Apricot 554345

Emerald 554352

China Green 554319

Navy 554312

Lilac 554368

Snow White 554315

ITEM CODE:

FINISH: NOTES:

UPHOLSTERY FINISH:

Diameter: Length: Width: Height: Seat Height: Arm Height:Depth:

Item:

Manufacturer Basis of Design:

Product:

Mfg. Model No:

Description:

Location:

Quantity:

Double Sided Curvy Seating, Config E Zoeftig Vista Curvy Configuration E

Constructed of E1-E3 Configurations n/a

Metal Color: Black Finish Solid Surface Arm Caps: Durasein, Glacier Tundra, PM4872 Solid Surface: Durasein, Glacier Tundra, PM4872

30’-6” varies 57” 35“ 16” 26”

- 18 Seats: Seat Width 24”

- 2 Curved Collaborative Benches: 60 degrees radius

- 26 Arms

- 4 Half Tables Back to Back

- 2 Full Tables Back to Back

- Powered

- Provide all ganging and mounting hardware required to complete configuration as shown on plan

- Made up of Config E1, Config E2, Config E3, Config E4. Each configuration to be ganged together to create “Config E”.

Configurations E1-E4 must be able to be separated as needed for mainatainence FABRIC: F-6

SS-2

Rotunda

13Vista by Zoeftig

Upholstery: PVC Tomato 554285

Fire Red 554311

Melon 554361

Empire Green 554314

Quartz 554330

Royal Blue 554292

Mauve 554367

Persimmon 554303

Lox 554348

Chocolate 554318

Lime 554326

Mint Julep 554313

Blueberry 554286

Rosewood 554908

Nasturtium 554293

Indian Red 554289

Allspice 554304

Citrus 554122

Bluejay 554284

Colonial Blue 554346

Natural 554329

Marigold 554301

Melba 554365

Oak Brown 554363

Ocean Grey 554332

Marina 554283

Coal 554328

Black 554290

Saffron Silk 554294

Port 554351

Saddle Tan 554309

Moon Glow 554310

Bright Blue 554121

Cadet 554353

Slate 554316

Lemon Peel 554308

Deep Clay 554288

Camel 554305

Spruce 554325

Phoenician 554350

Fjord 554344

Grey 554358

Wheat 554327

Russet 554297

Rum Sherbert 554334

Jade 554317

Sky 554347

Expresso 554333

Light Grey 554331

New Burgundy 554287

Burnt Orange 554299

Ceylon Ivory 554334

Turk 554295

Light Blue 554123

Grape 554302

Glacier 554366

Wine 554307

Brandy 554336

Hunter Green 554296

Light Teal 554300

Cerulean 554349

Purple Iris 554291

White 554306

Candy Apple 554298

Apricot 554345

Emerald 554352

China Green 554319

Navy 554312

Lilac 554368

Snow White 554315

Config E1

Config E2Config E

Config E2

Config E3

ITEM CODE:

FINISH: NOTES:

UPHOLSTERY FINISH:

Diameter: Length: Width: Height: Seat Height: Arm Height:Depth:

Item:

Manufacturer Basis of Design:

Product:

Mfg. Model No:

Description:

Location:

Quantity:

Single sided tandem seating, Config A1 Zoeftig Vista Configuration A1

Single sided tandem seating with tables and tablet arms n/a

Metal Color: Black Finish Solid Surface Arm Caps: Durasein, Glacier Tundra, PM4872 Solid Surface: Durasein, Glacier Tundra, PM4872

11’-6” 24” 25.5” 33” 17” 26”

- 4 Seats

- 1 Full Width Table

- 2 Tablet arms

- 2 Half Width Tables

- 4 Arm

- No Power

FABRIC: F-6

SS-3

First Floor Lobby/ Check-In

13Vista by Zoeftig

Upholstery: PVC Tomato 554285

Fire Red 554311

Melon 554361

Empire Green 554314

Quartz 554330

Royal Blue 554292

Mauve 554367

Persimmon 554303

Lox 554348

Chocolate 554318

Lime 554326

Mint Julep 554313

Blueberry 554286

Rosewood 554908

Nasturtium 554293

Indian Red 554289

Allspice 554304

Citrus 554122

Bluejay 554284

Colonial Blue 554346

Natural 554329

Marigold 554301

Melba 554365

Oak Brown 554363

Ocean Grey 554332

Marina 554283

Coal 554328

Black 554290

Saffron Silk 554294

Port 554351

Saddle Tan 554309

Moon Glow 554310

Bright Blue 554121

Cadet 554353

Slate 554316

Lemon Peel 554308

Deep Clay 554288

Camel 554305

Spruce 554325

Phoenician 554350

Fjord 554344

Grey 554358

Wheat 554327

Russet 554297

Rum Sherbert 554334

Jade 554317

Sky 554347

Expresso 554333

Light Grey 554331

New Burgundy 554287

Burnt Orange 554299

Ceylon Ivory 554334

Turk 554295

Light Blue 554123

Grape 554302

Glacier 554366

Wine 554307

Brandy 554336

Hunter Green 554296

Light Teal 554300

Cerulean 554349

Purple Iris 554291

White 554306

Candy Apple 554298

Apricot 554345

Emerald 554352

China Green 554319

Navy 554312

Lilac 554368

ITEM CODE:

FINISH: NOTES:

UPHOLSTERY FINISH:

Diameter: Length: Width: Height: Seat Height: Arm Height:Depth:

Item:

Manufacturer Basis of Design:

Product:

Mfg. Model No:

Description:

Location:

Quantity:

Single sided tandem seating Config B Zoeftig Vista Configuration B

Single sided tandem seating with tables and tablet arms n/a

Metal Color: Black Finish Solid Surface Arm Caps: Durasein, Glacier Tundra, PM4872 Solid Surface: Durasein, Glacier Tundra, PM4872

20’-4” 24” 25.5” 33” 17” 26”

- 8 Seats -4 Tablet arms

- 1 Full Width Table

- 3 Half table width

- 7 Arms

- No Power

FABRIC: F-6

SS-4

First Floor Lobby/ Check-In

13Vista by Zoeftig

Upholstery: PVC Tomato 554285

Fire Red 554311

Melon 554361

Empire Green 554314

Quartz 554330

Royal Blue 554292

Mauve 554367

Persimmon 554303

Lox 554348

Chocolate 554318

Lime 554326

Mint Julep 554313

Blueberry 554286

Rosewood 554908

Nasturtium 554293

Indian Red 554289

Allspice 554304

Citrus 554122

Bluejay 554284

Colonial Blue 554346

Natural 554329

Marigold 554301

Melba 554365

Oak Brown 554363

Ocean Grey 554332

Marina 554283

Coal 554328

Black 554290

Saffron Silk 554294

Port 554351

Saddle Tan 554309

Moon Glow 554310

Bright Blue 554121

Cadet 554353

Slate 554316

Lemon Peel 554308

Deep Clay 554288

Camel 554305

Spruce 554325

Phoenician 554350

Fjord 554344

Grey 554358

Wheat 554327

Russet 554297

Rum Sherbert 554334

Jade 554317

Sky 554347

Expresso 554333

Light Grey 554331

New Burgundy 554287

Burnt Orange 554299

Ceylon Ivory 554334

Turk 554295

Light Blue 554123

Grape 554302

Glacier 554366

Wine 554307

Brandy 554336

Hunter Green 554296

Light Teal 554300

Cerulean 554349

Purple Iris 554291

White 554306

Candy Apple 554298

Apricot 554345

Emerald 554352

China Green 554319

Navy 554312

Lilac 554368

ITEM CODE:

FINISH: NOTES:

UPHOLSTERY FINISH:

Diameter: Length: Width: Height: Seat Height: Arm Height:Depth:

Item:

Manufacturer Basis of Design:

Product:

Mfg. Model No:

Description:

Location:

Quantity:

Single sided tandem seating, Config A2 Zoeftig Vista Configuration A2

Single sided tandem seating with tables and tablet arms n/a

Metal Color: Black Finish Solid Surface Arm Caps: Durasein, Glacier Tundra, PM4872 Solid Surface: Durasein, Glacier Tundra, PM4872

11’-6” 24” 25.5” 33” 17” 26”

- 4 Seats

- 1 Full Width Table

- 2 Tablet arms

- 2 Half Width Tables

- 4 Arm

- Powered - No USB

FABRIC: F-6

SS-5

First Floor Lobby/ Check-In

13Vista by Zoeftig

Upholstery: PVC Tomato 554285

Fire Red 554311

Melon 554361

Empire Green 554314

Quartz 554330

Royal Blue 554292

Mauve 554367

Persimmon 554303

Lox 554348

Chocolate 554318

Lime 554326

Mint Julep 554313

Blueberry 554286

Rosewood 554908

Nasturtium 554293

Indian Red 554289

Allspice 554304

Citrus 554122

Bluejay 554284

Colonial Blue 554346

Natural 554329

Marigold 554301

Melba 554365

Oak Brown 554363

Ocean Grey 554332

Marina 554283

Coal 554328

Black 554290

Saffron Silk 554294

Port 554351

Saddle Tan 554309

Moon Glow 554310

Bright Blue 554121

Cadet 554353

Slate 554316

Lemon Peel 554308

Deep Clay 554288

Camel 554305

Spruce 554325

Phoenician 554350

Fjord 554344

Grey 554358

Wheat 554327

Russet 554297

Rum Sherbert 554334

Jade 554317

Sky 554347

Expresso 554333

Light Grey 554331

New Burgundy 554287

Burnt Orange 554299

Ceylon Ivory 554334

Turk 554295

Light Blue 554123

Grape 554302

Glacier 554366

Wine 554307

Brandy 554336

Hunter Green 554296

Light Teal 554300

Cerulean 554349

Purple Iris 554291

White 554306

Candy Apple 554298

Apricot 554345

Emerald 554352

China Green 554319

Navy 554312

Lilac 554368