0.1 1240LT25R0022 Amendment 0001.pdf

(x)

1240LT25R0022

x x

1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted ; or (c) By separate letter or electronic communication which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGEMENT TO BE

RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR

OFFER. If by virtue of this amendment you desire to change an offer already submitted , such change may be made by letter or electronic communication, provided each letter or electronic communication makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

x

40LT

OGDEN UT 84401-2310

324 25TH ST

USDA-FS CSA INTERMOUNTAIN 8

08/09/20250001

13. THIS ITEM ONLY APPLIES TO MODIFICATION OF CONTRACTS/ORDERS. IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

12. ACCOUNTING AND APPROPRIATION DATA (If required) is not extended.is extended, Items 8 and 15, and returning

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended , by one of the following methods: (a) By completing

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

FACILITY CODE CODE

10B. DATED (SEE ITEM 13)

10A. MODIFICATION OF CONTRACT/ORDER NO.

9B. DATED (SEE ITEM 11)

9A. AMENDMENT OF SOLICITATION NO.

CODE

8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, State and ZIP Code)

7. ADMINISTERED BY (If other than Item 6)CODE 6. ISSUED BY

PAGE OF PAGES

4. REQUISITION/PURCHASE REQ. NO.3. EFFECTIVE DATE2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO. (If applicable)

1. CONTRACT ID CODE

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

06/28/2025

CHECK ONE A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority) appropriation data, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

E. IMPORTANT: Contractor is not is required to sign this document and return __________________ copies to the issuing office.

ORDER NO. IN ITEM 10A.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

Humboldt Toiyabe National Forest

Lovell Well Construction Project

Amendment 0001 makes the following changes to the solicitation:

1. Attachment 3. Drawings, sheet D-1 (page 5), is amended as shown on page 3 below. Changes are outlined in red.

2. Questions and Answers posted will be a part of any resulting award.

The response date is 8/15/2025, at 12:00 pm MT.

Continued ...

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)15A. NAME AND TITLE OF SIGNER (Type or print)

15C. DATE SIGNED 16B. UNITED STATES OF AMERICA 15B. CONTRACTOR/OFFEROR 16C. DATE SIGNED

(Signature of person authorized to sign) (Signature of Contracting Officer)

LONNIE D. ROOT

STANDARD FORM 30 (REV. 11/2016)

Prescribed by GSA FAR (48 CFR) 53.243

Previous edition unusable

Except as provided herein, all terms and conditions of the document referenced in Item 9 A or 10A, as heretofore changed, remains unchanged and in full force and effect .

ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

NAME OF OFFEROR OR CONTRACTOR

2 3

CONTINUATION SHEET

REFERENCE NO. OF DOCUMENT BEING CONTINUED PAGE OF

(A) (B) (C) (D) (E) (F)

1240LT25R0022/0001

Period of Performance: 09/02/2025 to 11/01/2025

Contracting Specialist: Tony Taylor -tony.taylor@usda.gov

Contracting Officer Representative (COR) - Kevin

Wilmot - kevin.wilmot@usda.gov

NSN 7540-01-152-8067 OPTIONAL FORM 336 (4-86)

Sponsored by GSA

FAR (48 CFR) 53.110

DRAWN

DESIGNER

STAMPS, LOGOS, AND SEALS

PROJECT NAME

DRAWING TITLE

CHECKED

ARCHIVE NO.DATE

PROJECT NO.

DRAWING SHEET NO.

DATENO.

REVISION / ISSUE

OFSHEET

United States Department of Agriculture Forest Service

-- A

UT

OD

ES

K D

RA

W

IN

G1 .D

W G;

R4

INTERMOUNTAIN REGION

LOVELL WELL

CONSTRUCTION

HUMBOLDT-TOIYABE

NATIONAL FOREST

SPRING MOUNTAINS NATIONAL

RECREATION AREA

WELL CONSTRUCTION

AND TESTING

2/21/2025

C CUBIC

C CUBIC

A.LUSTY

D-1 5 5

AutoCAD SHX Text WELL INSTALLATION NOTES: 1. DRILL WELL TO THE DEPTH REQUIRED TO PRODUCE 100 GPM OF WATER DRILL WELL TO THE DEPTH REQUIRED TO PRODUCE 100 GPM OF WATER WITHOUT SIGNIFICANT DRAWDOWN. ACTUAL DEPTH OF WELL MAY VARY BETWEEN 400 FEET AND 500 FEET. IF THE REQUIRED WATER PRODUCTION CANNOT BE PRODUCED, A LOWER PRODUCTION RATE MAY BE APPROVED BY THE CONTRACTING OFFICER. 2. THE WATER BEARING FORMATION IS EXPECTED TO BE THE WATER BEARING FORMATION IS EXPECTED TO BE DOLOMITE/LIMESTONE DEPOSITS. VOIDS MAY BE ENCOUNTERED IN THE FORMATION. 3. IF IT IS POSSIBLE TO DRILL OPEN HOLE: END THE 8" STEEL CASING 10' IF IT IS POSSIBLE TO DRILL OPEN HOLE: END THE 8" STEEL CASING 10' BELOW THE GROUT SEAL (OR 10' BELOW THE DEPTH THAT THE FORMATION CAN SUPPORT ITSELF) 4. THE LOCATION OF THE WELL AND ORIENTATION OF THE PITLESS UNIT THE LOCATION OF THE WELL AND ORIENTATION OF THE PITLESS UNIT AND HDPE PIPE WILL BE STAKED BY THE CONTRACTOR AND APPROVED BY THE CONTRACTING OFFICER BEFORE DRILLING. 5. THE CASING (TOP OF PITLESS UNIT) SHALL EXTEND FAR ENOUGH ABOVE THE CASING (TOP OF PITLESS UNIT) SHALL EXTEND FAR ENOUGH ABOVE EXISTING GROUND SO THAT WHEN THE AREA AROUND THE CASING IS GRADED, THE CASING WILL EXTEND TO THE DISTANCE INDICATED ABOVE FINAL GROUND. 6. SURFACE WATER SHALL BE DIVERTED AS NEEDED TO PREVENT SURFACE WATER SHALL BE DIVERTED AS NEEDED TO PREVENT CONTAMINATION OF THE WELL. 7. GRADE AREA AROUND WELL CASING TO DRAIN AWAY FROM CASING. GRADE AREA AROUND WELL CASING TO DRAIN AWAY FROM CASING. 8. INSTALL SWING JOINT AT PITLESS UNIT CONNECTION TO REDUCE STRAIN INSTALL SWING JOINT AT PITLESS UNIT CONNECTION TO REDUCE STRAIN CAUSED BY SETTLING SOILS. THE SWING JOINT SHALL CONSIST OF TWO 90-DEG. GALVANIZED STEEL ELBOWS. THE ORIENTATION OF THE SWING JOINT SHALL BE SUCH THAT ANY SETTLING THAT OCCURS WILL TIGHTEN THE THREADS.

AutoCAD SHX Text

2" HDPE

AutoCAD SHX Text

EXISTING GROUND

AutoCAD SHX Text

SLOPE 2%

AutoCAD SHX Text

WELL INSTALLATION DETAIL NO SCALE

AutoCAD SHX Text

2% SLOPE

AutoCAD SHX Text

NEAT CEMENT GROUT SEAL

AutoCAD SHX Text

12" OVERSIZE BOREHOLE FOR GROUT SEAL. WITHDRAW OVERSIZED CASING IF USED.

AutoCAD SHX Text

8" STEEL CASING

AutoCAD SHX Text

FIELD WELD PITLESS UNIT TO WELL CASING

AutoCAD SHX Text

INSTALL PITLESS UNIT

AutoCAD SHX Text

INSTALL LOCKABLE, SANITARY WELL CAP

AutoCAD SHX Text

CAP PIPE & MARK AT SURFACE

AutoCAD SHX Text INSTALL SWING JOINT, HDPE/GSP TRANSITION, AND 1-1/2 x 2" REDUCER (SEE NOTE 8)

AutoCAD SHX Text

WATER BEARING STRATA

AutoCAD SHX Text

6" STAINLESS STEEL WELL SCREEN

AutoCAD SHX Text

END OF 8" STEEL CASING

AutoCAD SHX Text

6" PVC RISER CASING SCH. 80 (INCLUDED IN SCHEULE OF ITEMS 332100-3)

AutoCAD SHX Text

PACKER

AutoCAD SHX Text F

AutoCAD SHX Text O

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text S

AutoCAD SHX Text T

AutoCAD SHX Text S

AutoCAD SHX Text E

AutoCAD SHX Text R

AutoCAD SHX Text V

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text E

AutoCAD SHX Text D

AutoCAD SHX Text E

AutoCAD SHX Text P

AutoCAD SHX Text A

AutoCAD SHX Text R

AutoCAD SHX Text T

AutoCAD SHX Text M

AutoCAD SHX Text E

AutoCAD SHX Text N

AutoCAD SHX Text T

AutoCAD SHX Text O

AutoCAD SHX Text F

AutoCAD SHX Text A

AutoCAD SHX Text G

AutoCAD SHX Text R

AutoCAD SHX Text I

AutoCAD SHX Text C

AutoCAD SHX Text U

AutoCAD SHX Text L

AutoCAD SHX Text T

AutoCAD SHX Text U

AutoCAD SHX Text R

AutoCAD SHX Text E

AutoCAD SHX Text

REVISION 1

AutoCAD SHX Text 8/25

AutoCAD SHX Text

AutoCAD SHX Text aseiler Polygon aseiler Polygon aseiler Polygon