102800_FL-TOILET_BATH_AND_LAUNDRY_ACCESSORIES_v1.pdf

CHICOPEE ARMORY REHABILITATION MMD PROJECT NO. 985101

CHICOPEE, MASSACHUSETTS ISSUED FOR BID - 05/20/11

10090 TOILET, BATH, AND LAUNDRY ACCESSORIES 102800 - 1

SECTION 102800

TOILET, BATH, AND LAUNDRY ACCESSORIES

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary

Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section Includes:

1. Public-use washroom accessories.

2. Public-use shower room accessories.

1.3 ACTION SUBMITTALS

A. Product Data: For each type of product indicated. Include the following:

1. Construction details and dimensions.

2. Anchoring and mounting requirements, including requirements for cutouts in other work and substrate preparation.

3. Material and finish descriptions.

4. Features that will be included for Project.

5. Manufacturer's warranty.

1.4 QUALITY ASSURANCE

A. Source Limitations: For products listed together in the same Part 2 articles, obtain products from single source from single manufacturer.

1.5 COORDINATION

A. Coordinate accessory locations with other work to prevent interference with clearances required for access by people with disabilities, and for proper installation, adjustment, operation, cleaning, and servicing of accessories.

10090 TOILET, BATH, AND LAUNDRY ACCESSORIES 102800 - 2

PART 2 - PRODUCTS

2.1 MATERIALS

A. Stainless Steel: ASTM A 666, Type 304, 0.031-inch minimum nominal thickness unless otherwise indicated.

B. Brass: ASTM B 19, flat products; ASTM B 16/B 16M, rods, shapes, forgings, and flat products with finished edges; or ASTM B 30, castings.

C. Steel Sheet: ASTM A 1008/A 1008M, Designation CS (cold rolled, commercial steel), 0.036-inch minimum nominal thickness.

D. Galvanized-Steel Sheet: ASTM A 653/A 653M, with G60 hot-dip zinc coating.

E. Galvanized-Steel Mounting Devices: ASTM A 153/A 153M, hot-dip galvanized after fabrication.

F. Fasteners: Screws, bolts, and other devices of same material as accessory unit and tamper-and-theft resistant where exposed, and of galvanized steel where concealed.

G. Chrome Plating: ASTM B 456, Service Condition Number SC 2 (moderate service).

H. Mirrors: ASTM C 1503, Mirror Glazing Quality, clear-glass mirrors, nominal 6.0 mm thick.

I. ABS Plastic: Acrylonitrile-butadiene-styrene resin formulation.

2.2 PUBLIC-USE WASHROOM ACCESSORIES

A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following:

1. A & J Washroom Accessories, Inc.

2. American Specialties, Inc.

3. Bobrick Washroom Equipment, Inc.

4. Bradley Corporation.

5. GAMCO Specialty Accessories; a division of Bobrick Washroom Equipment, Inc.

B. Toilet Tissue (Roll) Dispenser :

1. Description: Roll-in-reserve dispenser with hinged front secured with tumbler lockset .

2. Mounting: Surface mounted.

3. Operation: Noncontrol delivery with theft-resistant spindle .

4. Capacity: Designed for 4-1/2- or 5-inch- diameter tissue rolls.

5. Material and Finish: Stainless steel, No. 4 finish (satin)

C. Paper Towel (Folded) Dispenser :

1. Mounting: Surface mounted.

2. Minimum Capacity: 400 C-fold or 525 multifold towels .

3. Material and Finish: Stainless steel, No. 4 finish (satin) .

4. Lockset: Tumbler type.

http://www.specagent.com/LookUp/?uid=123456793794&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123456793795&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123456793796&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123456793797&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123456793798&mf=04&src=wd

10090 TOILET, BATH, AND LAUNDRY ACCESSORIES 102800 - 3

5. Refill Indicators: Pierced slots at sides or front.

D. Grab Bar :

1. Mounting: Flanges with concealed] fasteners.

2. Material: Stainless steel, 0.05 inch thick.

a. Finish: Smooth, No. 4 finish (satin).

3. Outside Diameter: 1-1/4 inches .

4. Configuration and Length: As indicated on Drawings .

E. Mirror Unit :

1. Frame: Stainless-steel angle, 0.05 inch thick .

a. Corners: Manufacturer's standard] .

2. Hangers: Produce rigid, tamper- and theft-resistant installation, using method indicated below.

a. One-piece, galvanized-steel, wall-hanger device with spring-action locking mechanism to hold mirror unit in position with no exposed screws or bolts.

3. Size: 18” X 30” .

2.3 PUBLIC-USE SHOWER ROOM ACCESSORIES

A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following:

1. A & J Washroom Accessories, Inc.

2. American Specialties, Inc.

3. Bobrick Washroom Equipment, Inc.

4. Bradley Corporation.

5. GAMCO Specialty Accessories; a division of Bobrick Washroom Equipment, Inc.

B. Shower Curtain Rod :

1. Description: 1-inch OD; fabricated from nominal 0.0375-inch- thick stainless steel .

2. Mounting Flanges: Stainless-steel flanges designed for exposed fasteners .

3. Finish: No. 4 (satin) .

4. Size: Minimum 12 inches wider than opening by 72 inches high.

5. Material: Vinyl, minimum 0.006 inch thick, opaque, matte .

6. Color: White .

7. Grommets: Corrosion resistant at minimum 6 inches o.c. through top hem.

8. Shower Curtain Hooks: Chrome-plated or stainless-steel, spring wire curtain hooks with snap fasteners, sized to accommodate specified curtain rod. Provide one hook per curtain grommet.

C. Folding Shower Seat

1. Configuration: Stainless-steel seat designed to fold into recessed-mounted, stainless-steel wall box.

http://www.specagent.com/LookUp/?uid=123456793800&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123456793801&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123456793802&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123456793803&mf=04&src=wd http://www.specagent.com/LookUp/?uid=123456793804&mf=04&src=wd

10090 TOILET, BATH, AND LAUNDRY ACCESSORIES 102800 - 4

2. Seat: Phenolic or polymeric composite of slat-type or one-piece construction in color as selected by Architect .

3. Mounting Mechanism: Stainless steel, No. 4 finish (satin) .

D. Soap Dish

1. Description: Without washcloth bar.

2. Mounting: Surface mounted.

3. Material and Finish: Stainless steel, No. 4 finish (satin) .

E. Robe Hook

1. Description: Double -prong unit.

2. Material and Finish: Stainless steel, No. 4 finish (satin) .

2.4 FABRICATION

A. General: Fabricate units with tight seams and joints, and exposed edges rolled. Hang doors and access panels with full-length, continuous hinges. Equip units for concealed anchorage and with corrosion-resistant backing plates.

B. Keys: Provide universal keys for internal access to accessories for servicing and resupplying.

Provide minimum of six keys to Owner's representative.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Install accessories according to manufacturers' written instructions, using fasteners appropriate to substrate indicated and recommended by unit manufacturer. Install units level, plumb, and firmly anchored in locations and at heights indicated.

B. Grab Bars: Install to withstand a downward load of at least 250 lbf, when tested according to

ASTM F 446.

3.2 ADJUSTING AND CLEANING

A. Adjust accessories for unencumbered, smooth operation. Replace damaged or defective items.

B. Remove temporary labels and protective coatings.

C. Clean and polish exposed surfaces according to manufacturer's written recommendations.

END OF SECTION 102800