J065--FujiFilm Imaging Equipment Preventative Maintenance Service Base and Four Option Year

Intent to Sole Source- FujiFilm Healthcare Americas Corporation

The Department of Veterans Affairs intends to issue sole-source firm-fixed priced contract to FujiFilm Healthcare Americas Corporation 81 Hartwell Ave STE 300 Lexington, Massachusetts 02421-3160.

A sole source procurement will be issued to FujiFilm Healthcare Americas Corporation because they are the only vendor capable of fully performing the service and software updates for the below equipment. Due to the specialized nature of the work, it must be conducted by personnel with a high level of training and qualifications. Software updates and remote monitoring are available only through Fujifilm directly, as the author/owner of these codes. This procurement is being conducted in accordance with FAR Part 6.302-1 Only One Responsible Source and No Other Supplies or Services will satisfy agency requirements. The NAICS code is 811219 and has a size standard of $22 Million for this procurement.

Period of Performance: 10/01/2022-09/30/2027

SCOPE OF WORK:

The James H. Quillen VA Healthcare System (VAHCS) has a requirement for a service contract on FujiFilm Healthcare Americas Corporation, Radiology equipment, which shall provide routine preventative and corrective maintenance in order to ensure optimal working condition and lessen the likelihood of down time. The equipment listed below in the 1. EQUIPMENT section. All parts, labor and travel during normal business hours (8:30AM-5PM Local Time M-F), 24x7 / 365 phone support by a Certified Technical Support Engineer, one (1) preventative maintenance inspection and calibration (if applicable) per service agreement year, unless otherwise specified in FSMU Service Manual. During the annual PM, FMSU will update the Fujifilm application software to the latest version that the Operating System and PC hardware will support. FMSU does not install Microsoft Operating Systems patches or Antivirus software. If a new software version requires a new operating system or PC hardware, customer can elect to purchase at then current pricing for these items. One-hour phone response and a four-hour on-site response time for hard down systems within 150 miles of FMSU personnel. This contract is Base Plus Four, to be in effect no later than October 1, 2022, and will expire September 30, 2027.

It is required that service personnel are factory trained and certified on the FujiFilm Healthcare Americas Corporation, the equipment listed below in the 1. EQUIPMENT section. Training and certification documentation must be provided to the Contracting Officer s Representative (COR), listed in section 2. DEFINITIONS/ACRONYMS, upon execution of the contract and requested by the COR. This documentation is to remain on file with the COR.

1. EQUIPMENT:

Equipment to be serviced and/or maintained includes, but is not limited to: (Equipment is located at the James H. Quillen VA Medical Center, Mountain Home, TN)

Equipment Description

Serial Number

VISONARY Suite (no Panels)

MP95AA98A001

VISONARY Tube (Non-Discountable)

RM6D9278A001

IIP/FXD Monitor

721906313610.00

IIP/FXD Workstation

MXL8382JZQ

COLLIMATOR N FD 11 EL

MPC299D85004

VE FDR CH-200 F2W TOMO-S OTC

LZC5C5B8A005

VS FDR D-EVO Advanced Bucky Table

MP9C4558A003

VS FDR D-EVO Advanced Tilting Wall buckeye

MPA16648A002

VS FDR DR-ID900 MP

86820891

VS FDR DR-ID900 MC

86220562

AC-3CS CONTROL CONSOLE

2082125301

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i, 613 C24i

96420837

D-EVO I/II FDX No Fault DR-ID G35, G35i, G43i, C24i, C35i, C43i 2nd Panel

96520845

FDR GO without Panels (X-Ray Tube and Battery Panel Coverage Optional)

41F1168B85004

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i, 613 C24i

86652543

COLLIMATOR N FD 11 EL

LZ61AC685004

FDR GO (Shimadzu) Tube (Non-Discountable)

rm74b5a85002

FDR GO (Shimadzu) Battery Coverage with Main Contract

N/A

FDR GO without Panels (X-Ray Tube and Battery Panel Coverage Optional)

MQ0001289005

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i, 613 C24i

86952842

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i, 613 C24i 2nd Panel

87050656

FDR GO (Shimadzu) Tube (Non-Discountable)

rm74b6e88029

FDR GO (Shimadzu) Battery Coverage with Main Contract

N/A

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i, 613 C24i

96290050

IIP/FXD Monitor

B15C057432

IIP/FXD Workstation

2UA5041STP

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i, 613 C24i

87190262

FDR AcSelerate Suite - Two Panel Configuration

09-C0003

D-EVO MC(Control Cabinet)

97220975

AC-3CS Control Unit

26820051

AC-3CS Control Console

11-J0001

IIP/FXD Workstation

MXL3470S0P

IIP/FXD Monitor

H13C011340

FPD (For Wall and Table) R/Y898V 100835A

B120194

SMNS STA LT LOAD TNT STAND

5115

COLLIMATOR N FD 11 EL

1376

RAD CM TABLE MOVING GRID

5091

D-EVO I/II FDX no Fault DR-ID 611 C35i, 612 C43i, 613 C24i

37000280

D-EVO MP (POWER SUPPLY UNIT)

97190023

AcSelerate Tube Only (Non-Discountable)

H23579/57561-Q9

FDR AcSelerate Suite - Two Panel Configuration

14-I0146

AC-3CS Control Console

14-G0004

IIP/FDX Workstation

MXL51512PG

D-EVO MP (POWER SUPPLY UNIT)

97190015

D-EVO MC(Control Cabinet)

MXL8382JAZ

IIP/FDX Monitor

B15C057307

COLLIMATOR N FD 11 EL

6268

FPD (FOR Table) ALSO 898Y-100711

5173

FPD (FOR WALLSTAND) ALSO 898Y-100711

5204

371 Detector Unit

B120310

CARBON XL SUITE CHST BKY OTC-MAN-80KW

5182

DR200 PATIENT STAND FOR LV E

27020086

AcSelerate Tube Only (Non-Discountable)

H236170/61444-R9

E-DVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i, 613 C24i

6855463

FDR GO PLUS without Panels (X-ray tube & battery coverage optional) Contract Dates 1026/2022 to 9/30/2023

MQ00012B1008

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i , 613 C24i

Contract Dates 1026/2022 to 9/30/2023

6953010

FDR GO PLUS (Shimadzu) Tube (non-discountable)

Contract Dates 1026/2022 to 9/30/2023

N/A

FDR GO PLUS (Shimadzu) Battery Coverage with main contract, Contract Dates 1026/2022 to 9/30/2023

N/A

FDR GO PLUS without Panels (X-ray tube & battery coverage optional) Contract Dates 1026/2022 to 9/30/2023

MQ00012B1006

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43 , 613 C24i

Contract Dates 1026/2022 to 9/30/2023

6953011

FDR GO PLUS (Shimadzu) Tube (non-discountable)

Contract Dates 1026/2022 to 9/30/2023

N/A

FDR GO PLUS (Shimadzu) Battery Coverage with main contract, Contract Dates 1026/2022 to 9/30/2023

N/A

FDR GO PLUS without Panels (X-ray tube & battery coverage optional) Contract Dates 1026/2022 to 9/30/2023

MQ00012B1005

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43i , 613 C24i

Contract Dates 1026/2022 to 9/30/2023

6852956

FDR GO PLUS (Shimadzu) Tube (non-discountable)

Contract Dates 1026/2022 to 9/30/2023

N/A

FDR GO PLUS (Shimadzu) Battery Coverage with main contract, Contract Dates 1026/2022 to 9/30/2023

N/A

FDR GO PLUS without Panels (X-ray tube & battery coverage optional)

MQ00012B3022

D-EVO I/II FDX No Fault DR-ID 611 C35i, 612 C43 , 613 C24i

97090067

FDR GO PLUS (Shimadzu) Tube (non-discountable)

N/A

FDR GO PLUS (Shimadzu) Battery Coverage with main contract

N/A

4. CONFORMANCE STANDARDS:

Contract service shall ensure that the equipment functions in conformance with the latest published edition of NFPA-99, OSHA, includes performance standards and specifications.

5. UNSCHEDULED MAINTENANCE:

A. Contractor shall maintain the equipment in accordance with the Conformance Standards Section. The Contractor will provide repair service which may consist of calibration, cleaning, oiling, adjusting, replacing parts, (without additional cost to the Government), and maintaining the equipment, including all intervening calls necessary between regular services and calibrations. The contractor shall furnish all required parts. Parts being replaced for accidental damage, customer abuse or consumables (including but not limited to batteries) are not covered under this contract. Vendor will notify Contracting Officer to attain approval and separate PO prior to replacement.

B. The CO, COR, or designated alternate has the authority to approve/request a service call from the contractor.

6. SCHEDULED MAINTENANCE:

A. The Contractor shall perform PM service to ensure that equipment listed in the schedule performs in accordance with Section 3. CONFORMANCE STANDARDS. The contractor shall provide and utilize procedures and checklists with worksheet originals indicating work performed and actual values obtained (as applicable) provided to the COR at the completion of the PM. PM services shall include, but need not be limited to, the following:

1. Cleaning of equipment.

2. Reviewing operating system software diagnostics to ensure that the system is operating to the manufacturer s specifications.

3. Calibrating and lubricating the equipment.

4. Performing remedial maintenance of non-emergent nature.

5. Testing and replacing faulty and worn parts and/or parts which are likely to become faulty, fail or become worn.

6. Measuring and adjusting and calibrating as necessary for optimal image quality.

7. Inspecting, and replacing where indicated, electrical wiring and cables for wear and fraying.

8. Inspecting and replacing where indicated, all mechanical components including, but not limited to: patient restraints and support devices, cables and mounting hardware, chains, belts, bearings and tracks, interlocks, clutches, motors, keyboards, and patient couches for mechanical integrity, safety, and performance.

9. Returning the equipment to the operating condition defined in Section 3. CONFORMANCE STANDARDS.

10. Providing documentation of services performed.

11. Inspecting and calibrating the hard copy image device.

PM services shall be performed in accordance with, and during the hours defined in, the preventive maintenance schedule established herein. All exceptions to the PM schedule shall be arranged and approved in advance with the COR.

Any charges for parts, services, manuals, tools, or software required to successfully complete scheduled PM are included within this contract, and it s agreed upon price, unless specifically stated in writing otherwise.

B. The contractor shall furnish all backup documentation, including photographs of all measurements and calibrations, to ensure that the system is performing in accordance with the Conformance Standards. The following specific system operation parameters shall be surveyed, and documentation provided to the COR during the first (1st) and sixth (6th) month of the contract base period and annually thereafter during the eleventh (11th) month of each subsequent option period.

7. PARTS:

The contractor has ready access to unique and/or high mortality replacement parts. All parts supplied shall be OEM or equivalent and fully compatible with existing equipment. The contract invoice shall include all parts. The contractor shall use new or like new parts. Parts being replaced for accidental damage, customer abuse or consumables (including but not limited to batteries) are not covered under this contract. Vendor will notify Contracting Officer to attain approval and separate PO prior to replacement.

8. PERIOD OF PERFORMANCE:

Base Year:10/01/2022-09/30/2023

Option Year 1:10/01/2023-09/30/2024

Option Year 2:10/01/2024-09/30/2025

Option Year 3:10/01/2025-09/30/2026

Option Year 4:10/01/2026-09/30/2027

Other important considerations: Cite any other information that is necessary for potential respondents to understand the nature of the potential requirement or proposed acquisition.Â

Capability statement /information sought: Response to this announcement shall not to exceed 10 pages and should include the following information: (1) A tailored capability statement indicating the firm s ability to provide a product and related services; (2) The respondents DUNS number, organization name, address, point of contact, and size and type of business (e.g., SDVOSB/VOSB, etc,) pursuant to the applicable NAICS code; (3) Information should be provided electronically in a Microsoft Word or Adobe PDF format.

This notice of intent is not a request for competitive quotes. However, interested parties may identify their interest and capability to respond to the requirement and submit quotations with the subject line "Special Notice # 36C24922Q0334 by 08:00 a.m. on 05/16/2022 to: Christina.Lawrence2@va.gov. Responses received will be evaluated; however, a determination by the Government not to compete the proposed procurement based upon responses received to this notice is solely within the discretion of the Government.

Disclaimer and Important Notes. This notice does not obligate the Government to award a contract or otherwise pay for the information provided in response. The Government reserves the right to use information provided by respondents for any purpose deemed necessary and legally appropriate. Any organization responding to this notice should ensure that its response is complete and sufficiently detailed to allow the Government to determine the organization s qualifications to perform the work. Respondents are advised that the Government is under no obligation to acknowledge receipt of the information received or provide feedback to respondents with respect to any information submitted. After a review of the responses received, a pre-solicitation synopsis and solicitation may be published in Federal Business Opportunities. However, responses to this notice will not be considered adequate responses to a solicitation.

Confidentiality. No proprietary, classified, confidential, or sensitive information should be included in your response. The Government reserves the right to use any non-proprietary technical information in any resultant solicitation(s).