Additive Manufacturing for Flexible Electronics

Closed Solicitation Posted

Solicitation number
DME26BZ05-NV001
Agency
Responses due
Set-aside
Total Small Business

Opportunity facts

More information

Notice details come from DoD SBIR/STTR (DSIP). Updated .

About this opportunity

The Defense Microelectronics Activity seeks SBIR Phase I proposals for additive manufacturing of electronics processes for flexible electronics under topic DME26BZ05-NV001, with proposals due September 23, 2026, a date that has passed as of this summary. The set-aside is Total Small Business. Proposals must be submitted through the DoW SBIR/STTR Innovation Portal (DSIP), and proposals sent by other means are disregarded.

The work seeks additive manufacturing of electronics as an alternative to commercial advanced packaging and organic substrate fabrication, creating interconnects between components or between a component and a printed circuit board, and printing passive components to specified electrical ratings and tolerances. Phase I is a feasibility study and design of a Radio Frequency system, with targets that include trace and pitch widths of 5 mil or better, integration of a 12x12 BGA at 0.5mm ball pitch, and passive printing at 0.1% tolerance or better. The Phase I base amount must not exceed $200,000.00, with a technical period of performance not exceeding six months and a technical volume not exceeding 20 pages. Phase II is open only to Phase I awardees, who may submit without invitation within 60 calendar days after Phase I contract completion. Phase II may request up to $1,340,000.00 over 24 months to build, test, and deliver a functional Radio Frequency system, with a 40-page technical volume limit. DMEA provides up to $6,500 in discretionary Technical and Business Assistance for Phase I and up to $50,000 for Phase II.

Only unclassified proposals are accepted. The opportunity is listed as CMMC Level 1 and not ITAR-controlled. Phase I proposals require a coversheet, technical volume, cost volume, Company Commercialization Report, and supporting documents. Proposers receive Phase I selection notice within 90 days of topic closing. The NAICS code is 541715, and the PSC code is AC12.

Notice text

DoD SBIR topic DME26BZ05-NV001

Component: DMEA

Command: DMEA

Phase: SBIR Program Phase I Action

Technology Areas: Electronics; Materials

Focus Areas: Microelectronics

Keywords: Additive manufacturing of electronics (AME); Flexible Hybrid Electronics (FHE); AME based Radio Frequency system; Multi-Material 3D Printing; AME Systems.

ITAR: No

CMMC: Level 1

Objective:

The Department of War (DoW) is seeking the development of additive manufacturing of electronics (AME) processes by small businesses. Additive Manufacturing Methods are being investigated as an alternative to standard commercial Advanced Packaging techniques and Organic Substrate Fabrication. The AME process should have the ability to create interconnects between two or more components, or a component and printed circuit board. The process of additive manufacturing should specify its abilities to print the passive electronic components with electrical rating of the components and tolerances associated with target values.

Description:

Additive manufacturing, also referred to as 3D printing, has seen innovation in several critical areas in the field of electronics packaging and assembly from wafer level to printed circuit boards for low volume manufacturing and prototyping. Ceramic interposers are being manufactured using vat photopolymerization technologies to create substrates with channels for interconnects, that are backfilled through the process of metal infiltrations [1] The unique geometries enabled by the layer-to-layer technologies allow for routing options not possible with traditional fabrication techniques or fabrication quantities that are not economically viable. Semiconductor die pads to package substrate interconnects through 3D printed traces have been explored to replace traditional wire bonding connections. This enables smaller form factors as the wire height requirements are replaced with flat aerosol jet printed conductive traces created using nanoparticle inks [3]. The formulations of the conductive ink still pose challenges with material compatibility between interfaces [4], electrical resistance, and limited thermal operational ranges as each company creates material best suited to their printing system [2]. Printed interconnects open the doors for faster turnaround time, performance improvement through impedance matching for packaged devices [3], shorter interconnect lengths, and chip scaling through tool path alterations [4]. Additively manufactured printed circuit board assemblies which utilized printed traces and interconnects have also integrated printed passives such as resistors and capacitors into the boards [5]. These targets eliminating the need to pick and place passives in the assembly process as potentially any passive desired could be printed onto the boards. The three-dimensions fabrication methods also allow for the resistance values to be adjusted within a limited space.

Virtually every DoW system with electronics requires PCB manufacturing. Commercially available Substrate Manufacturing techniques and Advanced Packaging techniques are extremely expensive and require long lead times and are therefore not conducive to High Mix - Low Volume manufacturing efforts. It is desired to improve and validate existing additive manufacturing methods for use on government and commercial systems. Existing additive substrate fabrication and additive advanced packaging methods have been proven to be flexible, adaptable, and cost effective, there remains an undefined reliability risk. DoW is looking to enable these technologies. Specifically, by obtaining reliability data using MIL-STD quality and reliability metrics, these additive manufacturing technologies could become a viable alternative to traditional substrate manufacturing and advanced packaging. As a Phase I study, DoW is seeking the feasibility of developing a prototype via this effort directly comparable to existing Radio Frequency multichip modules (MCMs) currently used by the DoW. Additionally, the feasibility study may offer additional miniaturization or other forms of improvements that are of extreme interest to DoW. If such technology can produce prototypes with reliability comparable to standard manufacturing or reliable enough to fulfill target DoW missions, the additive manufacturing technologies could be used extensively on relevant microelectronic designs to reduce cost and manufacturing timelines for DoW Programs.

Phase I:

Conduct a feasibility study and design of a Radio Frequency system using additive manufacturing of electronics technologies. The design includes variety of surface mount components with packaging such as QFN, BGA, passive resistors, inductors and capacitors. The goal is to integrate all the components of the RF module onto additively fabricated substrate using additive manufacturing techniques like multi-material 3D printing or Flexible Hybrid Electronics (FHE) interconnect processes. Once assembled, such electronic module would be subjected to reliability tests. It is expected that the module produced by using AME processes would showcase the reliability of standard manufacturing processes or sufficient to meet DoW missions. The process shall meet the following target specifications.

 

  1.  Interconnect trace width of 5 mil or better
  2.  Interconnect pitch width of 5 mil or better
  3.  Ability to handle and integrate variety of surface mount components.
  4.  Ability to handle and integrate 12x12 BGA with 0.5mm ball pitch.
  5.  Printing and embedding passive components as flexible hybrid electronics.
  6.  Tolerance of printed passive components to be 0.1% or better.
  7.  Range of passive resistor from 1 ohm to 10 MOhm.
  8.  Range of passive capacitors from 1 picofarad to 1 microfarad.
  9.  Range of passive inductor from 1 picohenry to 100 nanohenry.
  10.  Ability to withstand 150°C temperature for long periods (10 hours) without reliability concerns.
  11.  Ability to be in storage at 125°C temperature for up to 4 weeks without reliability concerns.

 

The feasibility study shall detail the processes and techniques used along with associated costs. If there are bulk quantity discounts factored in, the report shall disclose quantity price break points and which steps were discounted wherever relevant. It must include:

 

  1.  Proposed manufacturing processes flow and techniques used including printing, bonding, interconnection, and assembly methodologies, along with figures and diagrams describing the process.
  2.  Bulk material and specification (i.e., substrate, printing material, materials for passives)
  3.  Cost breakdown for manufacturing compared to existing (both commercial and research) and comparative theoretical options.
  4.  Methodologies and analysis techniques used for characterizing the proposed methods.

 

Multiple feasibility studies may be appropriate, provided the proposed solutions address the goals in an incremental way and could be combined for a holistic final manufacturing solution and prototyped. Possible proposal topics should address one or more of the following phase 1 goals:

 

  1.  Goal 1: Demonstrate hybrid electronic manufacturing as an alternative to standard advanced packaging and soldering methods on existing organic substrate
  2.  Goal 2: Demonstrate additive manufacturing techniques for fine pitch and RF tuned circuitry on flexible substrates
  3.  Goal 3: Demonstrate hybrid electronic manufacturing techniques for printing passive components (resistors, capacitors) directly on flexible substrates
  4.  Goal 4: Provide hybrid electronic circuit design and layout for flexible substrate solution that replicates existing RF module functionality

 

The delivered report shall fully describe the proposed techniques and characterization methodologies, including a notional list of manufacturing tools, facility requirements, and a program plan for follow-on phase development. If any of the above items cannot be fully addressed, the report must include relevant research and rationale that demonstrates their inapplicability to the proposed technique. If adhering to the above items is possible, but not financially feasible, the report must include relevant justification. Finally, the challenges and special considerations for reliability testing and tolerances shall be addressed.

 

Phase II:

Build, test and deliver a fully functional Radio Frequency system based on the feasibility in Phase I. Demonstrate the capability of performance while adhering to the specifications outlined in Phase I. Production yields should be considered to keep costs with commercialization a viable option. The final report shall address manufacturing yield, reliability and reflect that the tested prototypes were selected from across multiple lots to demonstrate repeatability and quality with low variation within lots and lot to lot. If a non-random selection was required to optimize performance, the final report must detail reasoning for using non-random selection and the selection criteria used.

Deliver a detailed final report that documents the cost breakdown per device, manufacturing processes utilized, manufacturing toolset required to perform the proposed techniques, all facility requirements, all electrical characterization, and all device design data Technology Computer Aided Design (TCAD) files, modeling/simulation results, etc. If there are bulk quantity discounts factored in any of the cost breakdowns, the final report shall disclose quantity price break points and which steps were discounted wherever relevant. The final report shall contain sufficient technical detail such that an entity skilled in AME manufacturing can repeat the presented results.

Phase III:

This technology could be utilized for other DoW and commercial applications where additive manufacturing would be advantageous to cost, schedule or performance parameters.

Files

File Type Posted
DME26BZ05-NV001.pdf PDF
DMEA_SBIR_26BZ_R5.pdf PDF

On GovTribe

Work this opportunity

  • Track it in your pipeline
  • Find teaming partners
  • Similar opportunities
  • Ask GovTribe AI about this opportunity

GovTribe for Federal Contractors