DMEA_SBIR_26BZ_R5.pdf
PDF 188 KB Posted
- Attached to
- Additive Manufacturing for Flexible Electronics
- Solicitation number
- DME26BZ05-NV001
- Issued by
-
Defense Microelectronics Activity
About this file
This is a Proposal Submission Instructions document for the Defense Microelectronics Activity (DMEA) FY26 Small Business Innovation Research (SBIR) BAA Release 05. Proposers must follow all general Department of War (DoW) SBIR Program instructions with DMEA-specific requirements detailed in this document. All proposals must be submitted via the DoW SBIR/STTR Innovation Portal (DSIP); proposals submitted by other means will be disregarded. The solicitation is a small business set-aside exclusively for SBIR/STTR eligible companies.
Phase I proposals must include five volumes: a coversheet prepared on DSIP; a technical volume not exceeding 20 pages addressing solution feasibility; a cost volume with itemized detail including special tooling, materials, direct costs, labor, travel, cost sharing, subcontracts, and consultants; a Company Commercialization Report; and supporting documents. The Phase I base amount must not exceed $200,000.00 with a technical period of performance not exceeding six months. Phase II proposals (available only to Phase I awardees) may request up to $1,340,000.00 with a 24-month performance period and a 40-page technical volume limit. Phase I awardees may submit Phase II proposals without invitation within 60 calendar days following Phase I contract completion. DMEA will provide up to $6,500 in discretionary Technical and Business Assistance (TABA) for Phase I projects and up to $50,000 for Phase II projects. Proposers will be notified of Phase I selection status within 90 days of topic closing. Only unclassified proposals are accepted. A single topic is listed: DME26BZ05-NV001, titled "Additive Manufacturing for Flexible Electronics," which seeks development of additive manufacturing of electronics (AME) processes to create interconnects and passive components, with Phase I focusing on feasibility studies for Radio Frequency multichip modules and Phase II requiring prototype development and testing meeting specified technical targets.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| DME26BZ05-NV001.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
DMEA - 1
Defense Microelectronics Activity (DMEA) FY26 Small Business Innovation Research (SBIR)
BAA
Release 05
Proposal Submission Instructions
INTRODUCTION
The Defense Microelectronics Activity (DMEA) SBIR/STTR Program is implemented, administrated, and managed by the DMEA Office of Small Business Programs (OSBP).
Proposers responding to a topic in this solicitation must follow all general instructions provided in the Department of War (DoW) SBIR Program solicitation. DMEA requirements in addition to or deviating from the DoW Program solicitation are provided in the instructions below.
Proposers are encouraged to thoroughly review the DoW solicitation and register for the DSIP Listserv to remain apprised of important programmatic and contractual changes.
• The full DoW solicitation is available on DSIP at https://www.dodsbirsttr.mil/submissions/solicitation-documents/active-solicitations. Be sure to select the tab for the appropriate solicitation cycle.
• Register for the DSIP Listserv at: https://www.dodsbirsttr.mil/submissions/login.
Specific questions pertaining to the administration of the DMEA SBIR/STTR Program and these proposal preparation instructions should be directed to: DMEA SBIR/STTR Program at osd.mcclellanpark.dmea.list.sbir-sttr1@mail.mil
PHASE I PROPOSAL GUIDELINES
The DoW SBIR/STTR Innovation Portal (DSIP) is the official portal for DoW SBIR/STTR proposal submission. Proposers are required to submit proposals via DSIP; proposals submitted by any other means will be disregarded. Detailed instructions regarding registration and proposal submission via DSIP are provided in the DoW solicitation.
Proposal Coversheet (Volume 1)
The proposal coversheet is prepared on DSIP and in accordance with the DoW solicitation.
Technical Volume (Volume 2) The technical volume is not to exceed 20 pages and must follow the formatting requirements provided in the DoW SBIR solicitation. Technical volumes exceeding 20 pages will be deemed non-compliant and will not be evaluated.
Content of the Technical Volume Read the DoW SBIR Program BAA for detailed instructions on proposal format and program requirements. When you prepare your proposal submission, keep in mind that Phase I should address the feasibility of a solution to the topic. Only UNCLASSIFIED proposals will be accepted.
Cost Volume (Volume 3) The Phase I Base amount must not exceed $200,000.00. DMEA will conduct a price analysis to determine whether cost proposals, including quantities and prices, are fair and reasonable. The technical period of performance for the Phase I effort shall be no more than six (6) months.
https://www.dodsbirsttr.mil/submissions/solicitation-documents/active-solicitations https://www.dodsbirsttr.mil/submissions/solicitation-documents/active-solicitations https://www.dodsbirsttr.mil/submissions/login https://www.dodsbirsttr.mil/submissions/login https://www.dodsbirsttr.mil/submissions/login
DMEA - 2
Contractors should expect that cost proposals will be negotiated. Costs must be separated and clearly identified on the Proposal Cover Sheet (Volume 1) and in Volume 3.
The on-line cost volume for Phase I proposal submissions must be at a level of detail that would enable DMEA personnel to determine the purpose, necessity, and reasonability of each cost element. Provide sufficient information (a. through h. below) on how funds will be used if the contract is awarded. Include the itemized cost volume information (a. through h. below) as an appendix in your technical proposal. The itemized cost volume information (a. through h. below) will not count against the 20-page limit on Phase I proposal submissions.
a. Special Tooling and Test Equipment and Material: The inclusion of equipment and materials will be carefully reviewed relative to need and appropriateness of the work proposed.
The purchase of special tooling and test equipment must, in the opinion of the Contracting Officer, be advantageous to the Government and relate directly to the specific effort. They may include such items as innovative instrumentation and/or automatic test equipment. Title to furnished property by the Government or acquired with Government funds will be vested with the DoW Component; unless it is determined that transfer of the title to the contractor would be more cost effective than recovery of the equipment by the DoW Component.
b. Direct Cost Materials: Justify costs for materials, parts, and supplies with an itemized list containing types, quantities, price, and where appropriate, purposes.
c. Other Direct Costs: This category of costs includes specialized services such as machining or milling, special testing or analysis, costs incurred in obtaining temporary use of specialized equipment. Proposals, which include leased hardware, must provide an adequate lease versus purchase justification or rationale.
d. Direct Labor: Identify key personnel by name if possible or by labor category if specific names are not available. The number of hours, labor overhead and/or fringe benefits and actual hourly rates for each individual are also necessary.
e. Travel: Travel costs must relate to the needs of the project. Break out travel cost by trip, with the number of travelers, airfare, and per diem. Indicate the destination, duration, and purpose of each trip.
f. Cost Sharing: Cost sharing is permitted. However, cost sharing is not required, nor will it be an evaluation factor in the consideration of a proposal.
g. Subcontracts: Involvement of university or other consultants in the planning and /or research stages of the project may be appropriate. If the offeror intends such involvement, describe the involvement in detail and include information in the cost proposal. The proposed total of all consultant fees, facility leases, or usage fees and other subcontract or purchase agreements may not exceed one-third of the total contract price or cost, unless otherwise approved in writing by the Contracting Officer. Support subcontract costs with copies of the subcontract agreements. The supporting agreement documents must adequately describe the work to be performed (i.e., Cost Volume). At the very least, a statement of work with a corresponding detailed cost volume for each planned subcontract must be provided.
DMEA - 3
h. Consultants: Provide a separate agreement letter for each consultant. The letter should briefly state what service or assistance will be provided, the number of hours required, and the hourly rate.
Please review the updated Percentage of Work (POW) calculation details included in the DoW solicitation. Deviations from the POW requirements are not permitted.
Company Commercialization Report (CCR) (Volume 4) Completion of the CCR as Volume 4 of the proposal submission in DSIP is required. Please refer to the DoW solicitation for full details on this requirement. Information contained in the CCR will be considered by DMEA during proposal evaluations.
Supporting Documents (Volume 5) Volume 5 is provided for proposing SBCs to submit additional documentation to support the Coversheet (Volume 1), Technical Volume (Volume 2), and the Cost Volume (Volume 3). Please refer to the DoW solicitation for more information.
Fraud, Waste and Abuse Training (Volume 6) Fraud, Waste and Abuse training material can be found in the Volume 6 section of the proposal submission module in DSIP and must be thoroughly reviewed once per year to proceed with proposal submission.
Disclosures of Foreign Affiliations or Relationships to Foreign Countries (Volume 7) Small business concerns must complete the Disclosures of Foreign Affiliations or Relationships to Foreign Countries webform in Volume 7 of the DSIP proposal submission. Please be aware that the Disclosures of Foreign Affiliations or Relationships to Foreign Countries WILL NOT be accepted as a PDF Supporting Document in Volume 5 of the DSIP proposal submission. Do not upload any previous versions of this form to Volume 5. For additional details, please refer to the DoW Program BAA.
PHASE II PROPOSAL GUIDELINES
Phase II proposals may only be submitted by Phase I awardees. Phase II is the prototype/demonstration of the technology that was found feasible in Phase I. DMEA encourages, but does not require partnership and outside investment as part of discussions with DMEA sponsors for potential Phase II efforts.
The Technical Volume is not to exceed forty (40) pages and consists of a single PDF file with your firm name, topic number, and proposal number in the header of each page. All documentation should use no smaller than 10-point font on standard 8.5" X 11" paper with one-inch margins and not be in two-column format. Do not include blank pages.
Phase II proposals may be submitted for an amount not to exceed $1,340,000.00. The technical period of performance for the Phase II effort shall be no more than twenty-four (24) months.
Phase I awardees may submit a Phase II proposal without invitation not later than sixty (60) calendar days following the end of the Phase I contract. The Phase II proposal submission instructions are identified in the Phase I contract, Special Contract Requirements, “SBIR Phase II Proposal Submission Instructions”.
DMEA - 4
All Phase II proposals must have a complete electronic submission per the Proposal Volumes area listed in Phase I. Your proposal must be submitted via the submission site on or before the DMEA-specified deadline or it will not be considered for award.
Due to limited funding, DMEA’s ability to award any Phase II, regardless of proposal quality or merit, is subject to availability of funds. Please ensure that your proposal is valid for 180 days after submission Any extension to that time period will be requested by the Contracting Officer.
A Phase II contractor may receive up to one sequential Phase II award for continuing work on a project. A sequential Phase II award has the same guideline amounts and limits as an initial Phase II award. The sequential Phase II proposals shall be initiated by the Government Technical Point of Contact and must be approved by the DMEA SBIR/STTR Program Manager in advance.
DISCRETIONARY TECHNICAL AND BUSINESS ASSISTANCE (TABA)
The Small Business Innovation and Economic Security Act Section 7 mandates agencies to offer TABA.
DMEA will provide up to $6,500 per Phase I project and up to $50,000 per Phase II project.
EVALUATION AND SELECTION
All proposals will be evaluated in accordance with the evaluation criteria listed in the DoW solicitation.
Proposing firms will be notified of selection or non-selection status for a Phase I award within 90 days of the closing date of the topic.
Refer to the DoW solicitation for procedures to protest the Announcement.
As further prescribed in FAR 33.106(b), FAR 52.233-3, Protests after Award should be submitted to:
DMEA SBIR/STTR Program at osd.mcclellan-park.dmea.list.sbir-sttr1@mail.mil
DMEA - 5
DMEA SBIR DOW 2026 BAA
Topic Index
Release 5
DME26BZ05-NV001 TITLE: Additive Manufacturing for Flexible Electronics
DMEA - 6
DME26BZ05-NV001 TITLE: Additive Manufacturing for Flexible Electronics
OUSW (R&E) CRITICAL TECHNOLOGY AREA(S): Contested Logistics Technologies (LOG)
COMPONENT TECHNOLOGY PRIORITY AREA(S): Microelectronics
PROJECTED CMMC LEVEL REQUIREMENT: Level 1
OBJECTIVE: The Department of War (DoW) is seeking the development of additive manufacturing of electronics (AME) processes by small businesses. Additive Manufacturing Methods are being investigated as an alternative to standard commercial Advanced Packaging techniques and Organic Substrate Fabrication. The AME process should have the ability to create interconnects between two or more components, or a component and printed circuit board. The process of additive manufacturing should specify its abilities to print the passive electronic components with electrical rating of the components and tolerances associated with target values.
DESCRIPTION: Additive manufacturing, also referred to as 3D printing, has seen innovation in several critical areas in the field of electronics packaging and assembly from wafer level to printed circuit boards for low volume manufacturing and prototyping. Ceramic interposers are being manufactured using vat photopolymerization technologies to create substrates with channels for interconnects, that are backfilled through the process of metal infiltrations [1] The unique geometries enabled by the layer-to-layer technologies allow for routing options not possible with traditional fabrication techniques or fabrication quantities that are not economically viable. Semiconductor die pads to package substrate interconnects through 3D printed traces have been explored to replace traditional wire bonding connections. This enables smaller form factors as the wire height requirements are replaced with flat aerosol jet printed conductive traces created using nanoparticle inks [3]. The formulations of the conductive ink still pose challenges with material compatibility between interfaces [4], electrical resistance, and limited thermal operational ranges as each company creates material best suited to their printing system [2]. Printed interconnects open the doors for faster turnaround time, performance improvement through impedance matching for packaged devices [3], shorter interconnect lengths, and chip scaling through tool path alterations [4]. Additively manufactured printed circuit board assemblies which utilized printed traces and interconnects have also integrated printed passives such as resistors and capacitors into the boards [5].
These targets eliminating the need to pick and place passives in the assembly process as potentially any passive desired could be printed onto the boards. The three-dimensions fabrication methods also allow for the resistance values to be adjusted within a limited space.
Virtually every DoW system with electronics requires PCB manufacturing. Commercially available Substrate Manufacturing techniques and Advanced Packaging techniques are extremely expensive and require long lead times and are therefore not conducive to High Mix - Low Volume manufacturing efforts.
It is desired to improve and validate existing additive manufacturing methods for use on government and commercial systems. Existing additive substrate fabrication and additive advanced packaging methods have been proven to be flexible, adaptable, and cost effective, there remains an undefined reliability risk.
DoW is looking to enable these technologies. Specifically, by obtaining reliability data using MIL-STD quality and reliability metrics, these additive manufacturing technologies could become a viable alternative to traditional substrate manufacturing and advanced packaging. As a Phase I study, DoW is seeking the feasibility of developing a prototype via this effort directly comparable to existing Radio Frequency multichip modules (MCMs) currently used by the DoW. Additionally, the feasibility study may offer additional miniaturization or other forms of improvements that are of extreme interest to DoW. If
DMEA - 7
such technology can produce prototypes with reliability comparable to standard manufacturing or reliable enough to fulfill target DoW missions, the additive manufacturing technologies could be used extensively on relevant microelectronic designs to reduce cost and manufacturing timelines for DoW Programs.
PHASE I: Conduct a feasibility study and design of a Radio Frequency system using additive manufacturing of electronics technologies. The design includes variety of surface mount components with packaging such as QFN, BGA, passive resistors, inductors and capacitors. The goal is to integrate all the components of the RF module onto additively fabricated substrate using additive manufacturing techniques like multi-material 3D printing or Flexible Hybrid Electronics (FHE) interconnect processes.
Once assembled, such electronic module would be subjected to reliability tests. It is expected that the module produced by using AME processes would showcase the reliability of standard manufacturing processes or sufficient to meet DoW missions. The process shall meet the following target specifications.
1. Interconnect trace width of 5 mil or better
2. Interconnect pitch width of 5 mil or better
3. Ability to handle and integrate variety of surface mount components.
4. Ability to handle and integrate 12x12 BGA with 0.5mm ball pitch.
5. Printing and embedding passive components as flexible hybrid electronics.
6. Tolerance of printed passive components to be 0.1% or better.
7. Range of passive resistor from 1 ohm to 10 MOhm.
8. Range of passive capacitors from 1 picofarad to 1 microfarad.
9. Range of passive inductor from 1 picohenry to 100 nanohenry.
10. Ability to withstand 150°C temperature for long periods (10 hours) without reliability concerns.
11. Ability to be in storage at 125°C temperature for up to 4 weeks without reliability concerns.
The feasibility study shall detail the processes and techniques used along with associated costs. If there are bulk quantity discounts factored in, the report shall disclose quantity price break points and which steps were discounted wherever relevant. It must include:
1. Proposed manufacturing processes flow and techniques used including printing, bonding, interconnection, and assembly methodologies, along with figures and diagrams describing the process.
2. Bulk material and specification (i.e., substrate, printing material, materials for passives)
3. Cost breakdown for manufacturing compared to existing (both commercial and research) and comparative theoretical options.
4. Methodologies and analysis techniques used for characterizing the proposed methods.
Multiple feasibility studies may be appropriate, provided the proposed solutions address the goals in an incremental way and could be combined for a holistic final manufacturing solution and prototyped.
Possible proposal topics should address one or more of the following phase 1 goals:
1. Goal 1: Demonstrate hybrid electronic manufacturing as an alternative to standard advanced packaging and soldering methods on existing organic substrate
2. Goal 2: Demonstrate additive manufacturing techniques for fine pitch and RF tuned circuitry on flexible substrates
3. Goal 3: Demonstrate hybrid electronic manufacturing techniques for printing passive components
(resistors, capacitors) directly on flexible substrates
4. Goal 4: Provide hybrid electronic circuit design and layout for flexible substrate solution that replicates existing RF module functionality
DMEA - 8
The delivered report shall fully describe the proposed techniques and characterization methodologies, including a notional list of manufacturing tools, facility requirements, and a program plan for follow-on phase development. If any of the above items cannot be fully addressed, the report must include relevant research and rationale that demonstrates their inapplicability to the proposed technique. If adhering to the above items is possible, but not financially feasible, the report must include relevant justification. Finally, the challenges and special considerations for reliability testing and tolerances shall be addressed.
PHASE II: Build, test and deliver a fully functional Radio Frequency system based on the feasibility in Phase I. Demonstrate the capability of performance while adhering to the specifications outlined in Phase I. Production yields should be considered to keep costs with commercialization a viable option. The final report shall address manufacturing yield, reliability and reflect that the tested prototypes were selected from across multiple lots to demonstrate repeatability and quality with low variation within lots and lot to lot. If a non-random selection was required to optimize performance, the final report must detail reasoning for using non-random selection and the selection criteria used.
Deliver a detailed final report that documents the cost breakdown per device, manufacturing processes utilized, manufacturing toolset required to perform the proposed techniques, all facility requirements, all electrical characterization, and all device design data Technology Computer Aided Design (TCAD) files, modeling/simulation results, etc. If there are bulk quantity discounts factored in any of the cost breakdowns, the final report shall disclose quantity price break points and which steps were discounted wherever relevant. The final report shall contain sufficient technical detail such that an entity skilled in AME manufacturing can repeat the presented results.
PHASE III DUAL USE APPLICATIONS: This technology could be utilized for other DoW and commercial applications where additive manufacturing would be advantageous to cost, schedule or performance parameters.
REFERENCES:
1. Schaedler, Tobias A. / Porter, Kayleigh A. / Yu, Alex C. / Soukiazian, Souren / Sasse, Trevor / Wernick, Erin S. / Bui, Phuong P. / Hundley, Jacob M. / O’Masta, Mark “Additive manufacturing of interposers with curved vias for microelectronics packaging” R2025 Additive Manufacturing , Vol. 98 p. 104642
2. Seifert, Tobias / Baum, Mario / Roscher, Frank / Wiemer, Maik / Gessner, Thomas “Aerosol Jet Printing of Nano Particle Based Electrical Chip Interconnects”, 2015 Materials Today:
Proceedings , Vol. 2, No. 8 p. 4262-4271
3. Renn, Michael “Aerosol Jet Printing for Three Dimensional Interconnects”, 2025-01, IMAPSource Proceedings , Vol. 2024
4. Mengel, Manfred / Nikitin, Ivan “Inkjet printed dielectrics for electronic packaging of chip embedding modules” 2010 Microelectronic Engineering, Vol. 87, No. 4 p. 593-596
5. “Aerosol Jet Direct Writing Polymer-Thick-Film Resistors for Printed Electronics”. (2021).
Journal of Surface Mount Technology, 34(1), 24-31. https://doi.org/10.37665/smt.v34i1.13
KEYWORDS: Additive manufacturing of electronics (AME), Flexible Hybrid Electronics (FHE), AME based Radio Frequency system, Multi-Material 3D Printing, AME Systems.
| INTRODUCTION |
| PHASE I PROPOSAL GUIDELINES |
| Technical Volume (Volume 2) |
| Content of the Technical Volume |
| Cost Volume (Volume 3) |
| Company Commercialization Report (CCR) (Volume 4) |
| Supporting Documents (Volume 5) |
| Fraud, Waste and Abuse Training (Volume 6) |
| PHASE II PROPOSAL GUIDELINES |
| DISCRETIONARY TECHNICAL AND BUSINESS ASSISTANCE (TABA) |
| EVALUATION AND SELECTION |
File details come from the government source that posted it. Updated .