DME26BZ05-NV001.pdf
PDF 77 KB Posted
- Attached to
- Additive Manufacturing for Flexible Electronics
- Solicitation number
- DME26BZ05-NV001
- Issued by
-
Defense Microelectronics Activity
About this file
This is a presolicitation document for a federal contract opportunity issued by the Department of War (DoW) for the development of additive manufacturing of electronics (AME) processes. The solicitation number is DME26BZ05-NV001, titled "Additive Manufacturing for Flexible Electronics." The projected CMMC level requirement is Level 1, and the technology areas are Electronics and Materials with a modernization priority of Microelectronics. The DoW seeks small business contractors to develop AME processes as an alternative to standard commercial advanced packaging and organic substrate fabrication techniques, with the ability to create interconnects between components and printed circuit boards while printing passive electronic components with specified electrical ratings and tolerances.
Phase I requires a feasibility study and design of a Radio Frequency system using AME technologies, with specific target specifications including interconnect trace widths and pitch widths of 5 mil or better, integration of surface mount components and 12x12 BGA with 0.5mm ball pitch, printing of passive components with 0.1% tolerance or better, passive resistor ranges from 1 ohm to 10 MOhm, capacitor ranges from 1 picofarad to 1 microfarad, inductor ranges from 1 picohenry to 100 nanohenry, and temperature stability at 150°C for extended periods and 125°C storage for up to four weeks. The feasibility study must include proposed manufacturing process flows, bulk material specifications, cost breakdowns compared to existing methods, and characterization methodologies. Phase II requires building, testing, and delivering a fully functional Radio Frequency system with detailed documentation of manufacturing yields, processes, toolsets, facility requirements, and electrical characterization. Phase III addresses dual-use applications for DoW and commercial systems. No technical point of contact is currently listed, and the document includes five technical references on additive manufacturing innovations.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| DMEA_SBIR_26BZ_R5.pdf |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
DME26BZ05-NV001: Additive Manufacturing for Flexible Electronics
PROJECTED CMMC LEVEL REQUIREMENT:
Level 1
TECHNOLOGY AREAS:
Electronics | Materials
MODERNIZATION PRIORITIES:
Microelectronics
KEYWORDS:
Additive manufacturing of electronics (AME), Flexible Hybrid Electronics (FHE), AME based Radio Frequency system, Multi-Material 3D Printing, AME Systems.
ADDITIONAL INFORMATION
N/A
OBJECTIVE:
The Department of War (DoW) is seeking the development of additive manufacturing of electronics (AME) processes by small businesses. Additive Manufacturing Methods are being investigated as an alternative to standard commercial Advanced Packaging techniques and Organic Substrate Fabrication. The AME process should have the ability to create interconnects between two or more components, or a component and printed circuit board. The process of additive manufacturing should specify its abilities to print the passive electronic components with electrical rating of the components and tolerances associated with target values.
DESCRIPTION:
Additive manufacturing, also referred to as 3D printing, has seen innovation in several critical areas in the field of electronics packaging and assembly from wafer level to printed circuit boards for low volume manufacturing and prototyping. Ceramic interposers are being manufactured using vat photopolymerization technologies to create substrates with channels for interconnects, that are backfilled through the process of metal infiltrations [1] The unique geometries enabled by the layer-to-layer technologies allow for routing options not possible with traditional fabrication techniques or fabrication quantities that are not economically viable. Semiconductor die pads to package substrate interconnects through 3D printed traces have been explored to replace traditional wire bonding connections. This enables smaller form factors as the wire height requirements are replaced with flat aerosol jet printed conductive traces created using nanoparticle inks [3]. The formulations of the conductive ink still pose challenges with material compatibility between interfaces [4], electrical resistance, and limited thermal operational ranges as each company creates material best suited to their printing system [2]. Printed interconnects open the doors for faster turnaround time, performance improvement through impedance matching for packaged devices [3], shorter interconnect lengths, and chip scaling through tool path alterations [4]. Additively manufactured printed circuit board assemblies which utilized printed traces and interconnects have also integrated printed passives such as resistors and capacitors into the boards [5]. These targets eliminating the need to pick and place passives in the assembly process as potentially any passive desired could be printed onto the boards. The three-dimensions fabrication methods also allow for the resistance values to be adjusted within a limited space.
Virtually every DoW system with electronics requires PCB manufacturing. Commercially available Substrate Manufacturing techniques and Advanced Packaging techniques are extremely expensive and require long lead times and are therefore not conducive to High Mix - Low Volume manufacturing efforts. It is desired to improve and validate existing additive manufacturing methods for use on government and commercial systems. Existing additive substrate fabrication and additive advanced packaging methods have been proven to be flexible, adaptable, and cost effective, there remains an undefined reliability risk. DoW is looking to enable these technologies. Specifically, by obtaining reliability data using MIL-STD quality and reliability metrics, these additive manufacturing technologies could become a viable alternative to traditional substrate manufacturing and advanced packaging. As a Phase I study, DoW is seeking the feasibility of developing a prototype via this effort directly comparable to existing Radio Frequency multichip modules (MCMs) currently used by the DoW.
Additionally, the feasibility study may offer additional miniaturization or other forms of improvements that are of extreme interest to DoW. If such technology can produce prototypes with reliability comparable to standard manufacturing or reliable enough to fulfill target DoW missions, the additive manufacturing technologies could be used extensively on relevant microelectronic designs to reduce cost and manufacturing timelines for DoW Programs.
PHASE I:
Conduct a feasibility study and design of a Radio Frequency system using additive manufacturing of electronics technologies. The design includes variety of surface mount components with packaging such as QFN, BGA, passive resistors, inductors and capacitors. The goal is to integrate all the components of the RF module onto additively fabricated substrate using additive manufacturing techniques like multi-material 3D printing or Flexible Hybrid Electronics (FHE) interconnect processes. Once assembled, such electronic module would be subjected to reliability tests. It is expected that the module produced by using AME processes would showcase the reliability of standard manufacturing processes or sufficient to meet DoW missions. The process shall meet the following target specifications.
Interconnect trace width of 5 mil or better1.
Interconnect pitch width of 5 mil or better2.
Ability to handle and integrate variety of surface mount components.3.
Ability to handle and integrate 12x12 BGA with 0.5mm ball pitch.4.
Printing and embedding passive components as flexible hybrid electronics.5.
Tolerance of printed passive components to be 0.1% or better.6.
Range of passive resistor from 1 ohm to 10 MOhm.7.
Range of passive capacitors from 1 picofarad to 1 microfarad.8.
Range of passive inductor from 1 picohenry to 100 nanohenry.9.
Ability to withstand 150°C temperature for long periods (10 hours) without reliability concerns.10.
Ability to be in storage at 125°C temperature for up to 4 weeks without reliability concerns.11.
The feasibility study shall detail the processes and techniques used along with associated costs. If there are bulk quantity discounts factored in, the report shall disclose quantity price break points and which steps were discounted wherever relevant. It must include:
Proposed manufacturing processes flow and techniques used including printing, bonding, interconnection, and assembly methodologies, along with figures and diagrams describing the process.
1.
Bulk material and specification (i.e., substrate, printing material, materials for passives)2.
Cost breakdown for manufacturing compared to existing (both commercial and research) and comparative theoretical options.
3.
Methodologies and analysis techniques used for characterizing the proposed methods.4.
Multiple feasibility studies may be appropriate, provided the proposed solutions address the goals in an incremental way and could be combined for a holistic final manufacturing solution and prototyped. Possible proposal topics should address one or more of the following phase 1 goals:
Goal 1: Demonstrate hybrid electronic manufacturing as an alternative to standard advanced packaging and soldering methods on existing organic substrate
1.
Goal 2: Demonstrate additive manufacturing techniques for fine pitch and RF tuned circuitry on flexible substrates
2.
Goal 3: Demonstrate hybrid electronic manufacturing techniques for printing passive components (resistors, capacitors) directly on flexible substrates
3.
Goal 4: Provide hybrid electronic circuit design and layout for flexible substrate solution that replicates existing RF module functionality
4.
The delivered report shall fully describe the proposed techniques and characterization methodologies, including a notional list of manufacturing tools, facility requirements, and a program plan for follow-on phase development. If any of the above items cannot be fully addressed, the report must include relevant research and rationale that demonstrates their inapplicability to the proposed technique. If adhering to the above items is possible, but not financially feasible, the report must include relevant justification. Finally, the challenges and special considerations for reliability testing and tolerances shall be addressed.
PHASE II:
Build, test and deliver a fully functional Radio Frequency system based on the feasibility in Phase I. Demonstrate the capability of performance while adhering to the specifications outlined in Phase I. Production yields should be considered to keep costs with commercialization a viable option. The final report shall address manufacturing yield, reliability and reflect that the tested prototypes were selected from across multiple lots to demonstrate repeatability and quality with low variation within lots and lot to lot. If a non-random selection was required to optimize performance, the final report must detail reasoning for using non-random selection and the selection criteria used.
Deliver a detailed final report that documents the cost breakdown per device, manufacturing processes utilized, manufacturing toolset required to perform the proposed techniques, all facility requirements, all electrical characterization, and all device design data Technology Computer Aided Design (TCAD) files, modeling/simulation results, etc. If there are bulk quantity discounts factored in any of the cost breakdowns, the final report shall disclose quantity price break points and which steps were discounted wherever relevant. The final report shall contain sufficient technical detail such that an entity skilled in AME manufacturing can repeat the presented results.
PHASE III DUAL USE APPLICATIONS:
This technology could be utilized for other DoW and commercial applications where additive manufacturing would be advantageous to cost, schedule or performance parameters.
REFERENCES:
Schaedler, Tobias A. / Porter, Kayleigh A. / Yu, Alex C. / Soukiazian, Souren / Sasse, Trevor / Wernick, Erin S. / Bui, Phuong P. / Hundley, Jacob M. / O’Masta, Mark “Additive manufacturing of interposers with curved vias for microelectronics packaging” R2025 Additive Manufacturing , Vol. 98 p. 104642
1.
Seifert, Tobias / Baum, Mario / Roscher, Frank / Wiemer, Maik / Gessner, Thomas “Aerosol Jet Printing of Nano Particle Based Electrical Chip Interconnects”, 2015 Materials Today: Proceedings , Vol. 2, No. 8 p.
4262-4271
2.
Renn, Michael “Aerosol Jet Printing for Three Dimensional Interconnects”, 2025-01, IMAPSource Proceedings , Vol. 2024
3.
Mengel, Manfred / Nikitin, Ivan “Inkjet printed dielectrics for electronic packaging of chip embedding modules” 2010 Microelectronic Engineering, Vol. 87, No. 4 p. 593-596
4.
“Aerosol Jet Direct Writing Polymer-Thick-Film Resistors for Printed Electronics”. (2021). Journal of Surface Mount Technology, 34(1), 24-31. https://doi.org/10.37665/smt.v34i1.13
5.
TECHNICAL POINT OF CONTACT (TPOC):
None
File details come from the government source that posted it. Updated .