W912QR-22002077A_CERTFinal_Specs-0002.pdf

REPLY TO

ATTENTION OF

DEPARTMENT OF THE ARMY

LOUISVILLE DISTRICT, CORPS OF ENGINEERS

P.O. BOX 59

LOUISVILLE,KENTUCKY 40201-0059

Contracting Division 10 February 2025

A&H Ambica JV, LLC

Butt Construction Company, Inc.

Howard W. Pence, Inc.

KUNJ Construction Corp.

SES Construction and Fuel Services, LLC

FUTRON, Inc.

HDD JV

Dear MATOC Contractors:

Reference is made to Solicitation Number W912QR-22002077A for the IN ANG Small Indoor

Arms Range at Terre Haute, IN.

• See the attached Summary of Changes for Amendment 0002.

The proposal due date remains 11:00 AM ET on 17 February 2025. Submit your proposal by email to Stephanie Drees at Stephanie.N.Drees@usace.army.mil. Proposals not received by the stated date/time will not be considered. Please acknowledge receipt of this RFP amendment by signing below in the space provided and returning it with your proposal.

Please contact Stephanie Drees at Stephanie.N.Drees@usace.army.mil with any remaining questions. If an Offeror believes that the requirements in the RFP contain an error, omission, or are otherwise unsound; the offeror shall immediately notify the Contract Specialist in writing with supporting rationale. The Offeror is reminded that the Government reserves the right to award this RFP based on the initial proposals, as received, without discussion.

Sincerely, WESTGATE.JOSHUA.K

.1521895124

2025.02.10 12:41:16

-05'00'

Joshua K. Westgate

Contracting Officer

W912QR-22002077A_CERTFinal_Specs-000 mailto:Stephanie.N.Drees@usace.army.mil mailto:Stephanie.N.Drees@usace.army.mil

-2-

W912QR-22002077A AMENDMENT 0002 ACKNOWLEDGEMENT:

(Signature) (Date)

(Printed Name)

(Firm Name)

W912QR-22002077A_CERTFinal_Specs-000

-3-

SUMMARY OF CHANGES – AMENDMENT 0002

SUMMARY OF CHANGES

1. The following DIV 00 and DIV 01 SPECIFICATION SECTIONS have been revised and replaced in their entirety:

01 02 10.00 PROJECT DESCRIPTION AND DESIGN REQUIREMENTS

2. The submission date is changed from 17 February 2025 to 25 February 2025 at 11:00 AM ET.

Acknowledgement of receipt of this amendment and proposals are due at that time.

-4-

"General Decision Number: IN20250003 01/31/2025

Superseded General Decision Number: IN20240003

State: Indiana

Construction Type: Building

Counties: Clay, Gibson, Greene, Owen, Parke, Posey, Putnam, Sullivan, Vanderburgh, Vermillion, Vigo and Warrick Counties in

Indiana.

BUILDING CONSTRUCTION PROJECTS (does not include residential construction consisting of single family homes and apartments up to and including 4 stories)

Note: Contracts subject to the Davis-Bacon Act are generally required to pay at least the applicable minimum wage rate required under Executive Order 14026 or Executive Order 13658.

Please note that these Executive Orders apply to covered contracts entered into by the federal government that are subject to the Davis-Bacon Act itself, but do not apply to contracts subject only to the Davis-Bacon Related Acts, including those set forth at 29 CFR 5.1(a)(1).

|If the contract is entered |. Executive Order 14026 |

|into on or after January 30, | generally applies to the |

|2022, or the contract is | contract. |

|renewed or extended (e.g., an |. The contractor must pay |

|option is exercised) on or | all covered workers at |

|after January 30, 2022: | least $17.75 per hour (or |

| | the applicable wage rate |

| | listed on this wage |

| | determination, if it is |

| | higher) for all hours |

| | spent performing on the |

| | contract in 2025. |

|If the contract was awarded on|. Executive Order 13658 |

|or between January 1, 2015 and| generally applies to the |

|January 29, 2022, and the | contract. |

|contract is not renewed or |. The contractor must pay all|

|extended on or after January | covered workers at least |

|30, 2022: | $13.30 per hour (or the |

| | applicable wage rate listed|

| | on this wage determination,|

-5-

| | if it is higher) for all |

| | hours spent performing on |

| | that contract in 2025. |

The applicable Executive Order minimum wage rate will be adjusted annually. If this contract is covered by one of the

Executive Orders and a classification considered necessary for performance of work on the contract does not appear on this wage determination, the contractor must still submit a conformance request.

Additional information on contractor requirements and worker protections under the Executive Orders is available at http://www.dol.gov/whd/govcontracts.

Modification Number Publication Date 0 01/03/2025

1 01/17/2025 2 01/31/2025

ASBE0018-003 06/01/2024

CLAY, GREENE, OWEN, PARKE, PUTNAM, VERMILLION AND VIGO COUNTIES

Rates Fringes

ASBESTOS WORKER/HEAT & FROST

INSULATOR (includes application of all insulating materials protective coverings, coatings and finishes to all types of mechancial systems).............. $ 38.55 23.53

HAZARDOUS MATERIAL HANDLER

(includes preparation, wettings stripping, removal, scrapping, vacuuming, bagging

& disposing of all insulation materials, whether they contain asbestos or not, from mechanical systems).............. $ 23.00 14.40

ASBE0037-002 04/02/2023

GIBSON, POSEY, SULLIVAN, VANDERBURGH AND WARRICK COUNTIES

http://www.dol.gov/whd/govcontracts

-6-

ASBESTOS WORKER/HEAT & FROST

INSULATOR (includes application of all insulating materials protective coverings, coatings an finishes to all types of mechanical systems. Also the application of firestopping material openings and penetrations in walls, floors, ceilings, curtain walls and all lead abatement).......................$ 32.00 21.84

BOIL0374-002 01/01/2024

Rates Fringes

BOILERMAKER......................$ 42.41 35.72

BRIN0001-001 06/01/2023

EVANSVILLE

POSEY, VANDERBURGH and WARRICK COUNTIES

Rates Fringes

Bricklayer, Stonemason...........$ 34.17 20.14

Marble, Tile & Terrazzo

Finisher.........................$ 22.09 16.34

Marble, Tile & Terrazzo

Workers..........................$ 28.49 16.46

BRIN0004-012 06/01/2024

BLOOMINGTON

OWEN COUNTY

Bricklayer, Stonemason. ......... $ 35.21 18.19

TERRAZZO FINISHER ............... $ 25.33 14.19

TERRAZZO WORKER/SETTER ........... $ 37.97 18.06

Tile & Marble Finisher........... $ 25.33 14.19

Tile, Marble Setter. ............ $ 37.22 18.05

-7-

BRIN0005-001 09/21/2023

TERRE HAUTE CLAY, GIBSON, REENE, PARKE, SULLIVAN, VERMILLION

and VIGO COUNTIES

BRICKLAYER

BRICKLAYER, STONE MASON

and POINTER/CLEANER/CAULKER.$ 30.13 11.65

CEMENT MASON (GREENE and

SULLIVAN COUNTIES). ......... $ 27.78 11.02

CEMENT MASON (REMAINING

COUNTIES)...................$ 27.93 11.02

TERRAZZO FINISHER. ..........$ 23.38 1315

TERRAZZO....................$ 27.50 15.20

TILE and MARBLE FINISHER .... $ 19.83 6.32

TILE, MARBLE, MOSAIC ....... $ 35.63 17.23

CARP0088-001 10/01/2024

CLAY, OWEN, PARKE, PUTNAM, VERMILLION AND VIGO COUNTIES

Carpenters:

Carpenters, Drywall

Installers, Piledrivers.....$ 35.55 23.80

Millwright..................$ 36.94 25.42

Soft Floor Layers...........$ 34.45 21.08

CARP0224-004 04/01/2024

POSEY, VANDERBURGH AND WARRICK COUNTIES

CARPENTER

Carpenter...................$ 31.49 25.46

Piledriver..................$ 32.49 25.36

CARP0224-005 04/01/2024

GREENE, GIBSON and SULLIVAN COUNTIES

-8-

CARPENTER

Carpenter...................$ 31.48 25.46

Piledriver..................$ 28.71 22.45

CARP1080-002 04/01/2024

MILLWRIGHT

ZONE 1

POSEY, VANDERBURGH and

WARRICK COUNTIES...........$ 34.40 27.61

ZONE 2

GIBSON, GREENE AND

SULLIVAN COUNTIES..........$ 33.10 28.57

ELEC0016-004 04/01/2024

GIBSON, POSEY, VANDERBURGH AND WARRICK COUNTIES

ELECTRICIAN......................$ 43.51 20.92

ELEC0481-001 05/31/2024

PUTNAM COUNTY

ELECTRICIAN......................$ 42.15 26.88

* ELEC0538-002 06/01/2024

VERMILLION COUNTY

ELECTRICIAN......................$ 40.00 26.01

ELEC0725-003 10/01/2024

CLAY, GREENE, OWEN, PARKE, SULLIVAN AND VIGO COUNTIES

ELECTRICIAN......................$ 43.30 25.32

-9-

ELEC0725-010 06/01/2022

CLAY, GREENE, OWEN, PARKE, SULLIVAN AND VIGO COUNTIES

Communication Technician.........$ 30.00 18.07

Includes the installation, operation, inspection, maintenance, repair and service of radio, television, recording, voice sound and vision production and reproduction apparatus, equipment and appliances used for domestic, commercial, education, entertainment and private telephone systems.

ELEV0003-002 01/01/2023

GIBSON, POSEY, VANDERBURGH and WARRICK COUNTIES

ELEVATOR MECHANIC................$ 57.69 37.335+a+b

FOOTNOTES:

a) Employer contributes as a vacation pay credit 8% basic hourly rate for more than 5 years of service and 6% basic hourly rate for less than 5 years of service.

b) Eight Paid Holidays: Thanksgiving Day; New Year's Day;

Memorial Day; Independence Day; Labor Day; Veteran's Day, Thanksgiving Day, the Friday after Thanksgiving Day and

Christmas Day.

ELEV0034-002 01/01/2024

CLAY, GREENE, OWEN, PARKE, PUTNAM, SULLIVAN, VERMILLION and

VIGO COUNTIES

ELEVATOR MECHANIC................$ 57.68 37.885+a+b

a) PAID HOLIDAYS: New Year's Day, Memorial Day, Independence

Day, Labor Day, Vetern's Day, Thanksgiving Day, the Friday

-10-after Thanksgiving, and Christmas Day.

b) Employer contributes 8% of regular hourly rate to vacation pay credit for employee with more than 5 years of service;

6% for less than 5 years' service.

ENGI0181-013 04/01/2024

GIBSON, POSEY, VANDERBURGH, and WARRICK COUNTIES

Power equipment operators:

GROUP A.....................$ 41.28 19.72

GROUP B.....................$ 33.15 19.72

POWER EQUIPMENT OPERATOR CLASSIFICATIONS

GROUP A: A-Frame Winch Truck, Articulating dump, autograde

(CMI), auto patrol, ballast regulator (RR), batcher plant

(electrical control concrete), bending machine (pipe), bituminous plant (engineer), bituminous plant, bituminous mixer travel plant, bituminous paver, bituminous roller, boring machine, buck hoist, bull dozer, cable way, Chicago boom, chimney hoist, clamshell, concrete mixer (21 cu. ft.

or over), concrete paver, concrete pump (crete), construction elevator (Allmac or similar) crane, craneman, crawler backhoe, crawler high-lift, crusher plant, derrick, derrick boat, dinkey, directional/boring machine, dope pots

(pipeline), double drum tugger (electric or air), dragline, dredge operator, dredge engineer, drill operator, elevating grader, extendable boom forklift, formless paver, gantry crane, gator (or similar type tiller), gradeall, grader, grademan, greaser ( on grease facility servicing heavy equipment), G.P.S System (on equipment with the classifications), grout pump, head greaser, helicopter crew, Hetherington paver, hoist (motorized, gas or diesel), hydraulic crane, hydro blaster, Industrial type forklift

(over 9,000 lbs), laser concrete screed, laser or remote contrlled equipment (within the classifications), locomotive crane, locomotive, mechanic, mobile mixer, motor crane, mucking machine, multiple tamping machine (RR) overhead crane, pile driver, pulls, push dozer, push boats, roller (sheep foot), rough terrain crane, R.T. backhoe, R.T. endloader, Ross carrier, scoop, shovel, side boom, skidstter loader (obcat or similar type), swing crane, tail boom, tar machine (pipeline), tower crane, trench machine, -11-welder (heavey duty), truck mounted concrete pump, truck-mounted drill, vacuum truck, well point whirleys.

GROUP B: Air Compressor (1 or more, 600 cfm and over), air compressor with throttle valve, bituminous distrubtor, brakeman, bullfloat, cement gun, concrete mixer, concrete mixer, concrete saw, concrete spreader or puddlers, conveyor, deck hand oiler, deck engine, drill helper, earth roller, electric vibrator compactor (earth or rock), elevator (in-plant, automatic), finishing machine, fireman, form grader, generator, guard-rail driver, heater, oiler, Industrial type forklift (9,000 lbs and under), material pump, motor boats, paving joint machine, post hole digger, power broom, power traffic signals, rock roller, rock spreader, Roller (earth or rock), spike machine (RR), steam jenny, sub grader, tamping machine, truck crane oiler, truck mounted drill oiler, Tugger (one-drum, air or electric) vibrator, vibro-piling hammer-hydraulic hammer or auger, water pump, widener (apsco or similar type) welding machine, JLG lifts and scissor lifts or similar machine.

ENGI0841-001 04/01/2023

REMAINING COUNTIES

Power equipment operators:

GROUP 1.....................$ 33.90 23.00

GROUP 2.....................$ 26.75 23.00

GROUP 1: Power Cranes, Draglines, Derricks, Shovels, Gradalls, Mechanics, Tractor Highlift, Tournadozer, Concrete Mixers with Skip, Tournamixer, Two-Drum Machine, One-Drum Hoist with Tower or Boom, Cableways, Tower

Machines, Motor Patrol, Boom Tractor, Boom or Winch Truck, Winch or Hydraulic Boom Truck, Truck Crane, Tournapull, Tractor Operating Scoops, Bulldozer, Push Tractor, Asphalt

Planer, Finishing Machine on Asphalt, Large Rollers on

Earth, Rollers on Asphalt Mix, Ross Carrier or Similar

Machine, Gravel Processing Machine, Asphalt Plant Engineer, Paver Operator, Farm Tractor with Half Yard Bucket and/or

Backhoe Attachments, Dredge Engineer, or Dredge Operator, Central Mix Plant Engineer, CMI or Similar Type Machine, Truck or Skid Mounted Concrete Pump, Tower Crane, Engine or

Rock Crusher Plant, Concrete Plant Engineer, Ditching

Machine with Dual Attachment, Tractor Mounted Loaders, -12-

Cherry Picker, Hydro Crane, Standard or Dinkey Locomotives, Scoopmobiles, Euclid Loader, Soil Cement Machine, Back

Filler, Elevating Machine, Power Blade, Drilling Machines

Including Well Testing, Caissons, Shaft or Any Similar Type

Drilling Machines, Motor Driven Paint Machine, Pipe

Cleaning Machine, Pipe Wrapping Machine, Pipe Bending

Machine, Apsco Paver, Boring Machine, (Equipment Greased), Barber-Greene Loaders, Formless Paver, (Well Point System), Concrete Spreader, Hydra Ax, Span Saw and Similar Types, Marine Scoops, Brush Mulcher, Brush Burner, Mesh Placer, Tree Mover, Helicopter Crew (3), Piledriver - Skid or

Crawler, Stump Remover, Root Rake, Tug Boat Operator, Refrigerating Machine, Freezing Operator, Chair Cart-Self

Propelled, Hydra Seeder, Straw Blower Power Sub Grader, Bull Float, Finishing Machine, Self-Propelled Pavement

Breaker (Backhoe Attached), Lull (or Similar Type Machine), Two Air Compressors, Compressors Hooked in Maifold, Overhead Crane, Chip Spreader, Mud Cat, Sull-Air Fork Lifts

(Except When Used For Landscaping Work), Soil Stabilazer

(Seaman Tiller, Bo Mag, Rago Gator and Similar Types or

Equipment), Tube Float, Spray Machine, Curing Machine, Concrete or Asphalt Milling Machine, Snooper Truck Operator.

GROUP 2: Concrete Mixers Without Skips, Rock Crusher, Ditching Machine Under 6', Curbing Machine, One Drum

Machines without Tower or Boom, Air Tugger, Self-Propelled

Concrete Saw, Machine-Mounted Post Hole Digger, Two to Four

Generators, Water Pumps, or Welding Machines within 400 ft., Air Compressor 600 cu. ft. and Under, Rollers on

Aggregate and Seal Coat Surfaces, Fork Lifts (When Used For

Landscaping Work, Concrete and Blacktop Curb Machine, Farm

Tractor with less than Half Yard Bucket, One Water Pump, Iolers, Air Valves or Steam Valves, One Welding Machine, Truck Jack, Mud Jack, Gunnite Machine, House Elevators when used for Hoisting Material, Engine Tenders, Wagon Drill, Flex Plane, Conveyor, Siphons and Pulsometer, Switchman, Fireman on Paint Pots, Fireman on Asphalt Plants, Distributor Operators on Trucks, Tampers, Self-Propelled

Power Broom, Striping Machine (Motor Driven), Form Tamper, Bulk Cement Plan Equipment Greaser, Deck Hands, Truck Crane

Oiler Driver, Cement Blimps, Form Grader, Temporary Heat, Throttle Valve, Farm Tractor, Super Sucker (And Similar

Type of Equipment).

FOOTNOTE: Employees operating booms from 149 ft. to 199 ft.

including jib, shall receive an additional seventy five cents (.75) per hour above the rate. Employees operating booms over 199 ft. including jib, shall receive an

-13-additional one dollar and twenty five cents ($1.25) per hour above the regular rate.

IRON0022-003 06/01/2024

CLAY, DAVIESS, GREENE, KNOX, LAWRENCE, MARTIN, MONROE,

MONTGOMERY, OWEN, PARKE, PUTNAM, SULLIVAN, VERMILLION AND VIGO

COUNTIES

Rates Fringes

IRONWORKER.......................$ 36.70 26.09

The following holidays shall be observed: New Year's Day, Memorial Day, Independence Day, Labor Day, Thanksgiving Day and the day after Thanksgiving and Christmas Day. Any holiday which occurs on a Sunday shall be observed the following Monday, unless the legal observance of these holidays is changed by law.

IRON0103-003 04/01/2024

IRONWORKER.......................$ 35.34 25.75

LABO0204-002 06/01/2024

CLAY, GREENE, OWEN, PARKE, PUTNAM, SULLIVAN, VERMILLION, and

Laborers:

Caisson and Tunnel Work in

Compressed and Free Air

GROUP 1....................$ 23.18 16.00

GROUP 2....................$ 23.93 16.00

GROUP 3....................$ 24.18 16.00

GROUP 4....................$ 24.18 16.00

LABORERS

GROUP 1....................$ 26.93 18.00

-14-

GROUP 2....................$ 27.68 18.00

GROUP 3....................$ 28.43 18.00

LABORER CLASSIFICATIONS

GROUP1: Building and construction laborers; Scaffold builders (other than for masons or plasterers); Mechanic tenders; Flag & signal person; Window washers & cleaners;

Waterboys & toolhousemen; Railroad workers; Masonry wall washers (interior & exterior); Curing compound; All portable water pumps with discharge up to 3 inches;

Waterproofing; Handling of creosote lumber or like treated material (excluding railroad material); Asphalt rakers & lutemen; Kettlemen; Air tool operators and all pneumatic tool operators; Air & electric vibrators & chipping hammer operators: Earth compactors; Jackmen & sheet men working ditches deeper than 6 ft. in depth; Laborers working ditches 6 ft. in depth or deeper; Assembly of unicrete pump; Tile layers (sewer or field) & sewer pipe layer

(metallic or non-metallic); Motor-driven wheelbarrows & concrete buggies; Hyster operators; Pumpcrete assemblers;

Core drill operator; Cement, lime or silia clay handlers

(bulk or bag); Handling of toxic materials damaging to clothing; Pneumatic spikers; Deck engine & winch operators:

Water main & cable ducking (metallic/non-metallic); Screed man or screw operator on asphalt paver; Chain saw and demolition saw operators; Concrete conveyor assemblers;

Asbestos removal; Hazardous waste removal.

GROUP 2: Plasterers' tenders; Mortar mixers; Welders

(acetylene or electric); Cutting torch or burner; Cement nozzle laborers; Cement gun operators; Scaffold builders when working for plasterers and for masons; Water blast machine operators.

GROUP 3: Dynamite men; Mason Tenders; Drillers-air track or wagon drilling for explosives

LABORERS CLASSIFICATIONS For CAISSON And TUNNEL WORK In

COMPRESSED And FREE AIR

GROUP 1: Cage Tenders, Dump Men, Flagman, Signalman, Top

Laborers, Rod Men

GROUP 2: Concrete Repairmen, Lock Tenders (pressure side), Motor men, Muckers, Grout Machine, Track Layers, Air Hoist, Key Board, Agitator Car, Car Pushers, Concrete Laborers, -15-

Grout Laborers, Lock Tenders (free air side), Steel

Setters, Tuggers, Tuggers, Switchmen.

GROUP 3: Mucking Machine, Laser Beam, Liner Plate & Ring

Setter, Shield Drivers, Power Knife, Welders Burners, Pipe

Jacking Machine, Skinners, Maintenance Technician, Miner, Bricklayer Tenders, Concrete Blowers, Drillers, Erectors, Form Men, Jackhammermen, Mining Machine.

GROUP 4: Dynamite Men, Drillers air track or wagon drilling for explosives.

LABO0561-005 04/01/2023

GIBSON, POSEY, VANDERBURGH and WARRICK COUNTIES

Laborers:

GROUP 1.....................$ 27.12 18.10

GROUP 2.....................$ 27.42 18.10

GROUP 3.....................$ 28.62 18.10

GROUP 4.....................$ 28.87 18.10

LABORER CLASSIFICATIONS

GROUP 1: Building & Construction Laborers; Scaffold Builders

(other than for Masons or Plasterers); Ironworker Tender;

Mechanic Tender; Civil Engineer Tender; Rodmen and

Chainmen; Signalmen and Flagman, Window Washer & Cleaner;

Waterboy and Toolhouseman; Roofer Tender; Railroad Worker;

Masonry Wall Washer (Interior & Exterior); Cement Finisher

Tender; Carpenter Tender; All Other Tenders not listed;

Portable Water Pump with discharge up to 3""; Wiremesh; Fire

Prevention; Fire Watch; Fire Stop Tender

GROUP 2: Waterproofing; Handling of creosote Lumber or like treated material (Excluding Railroad Material); Asphalt

Raker & Luteman; Kettleman; handling and removal Hazardous materials damaging to clothing; Air Tool Operator;

Vibrator; Chipping Hammer Operator and all pneumatic tool operator and earth compactor; Jack Man & Sheeting Man

Working in Ditches 6 Feet in depth or deeper; Laborers working ditches six (6) feet in depth or deeper; Assembly of Unicrete Pump; Chain Saw Operator; Water line layers, five (5) feet outside the building foundation; Tile layers

(Sewer or Field); Sewer Pipe Layer (Metallic and

-16-

Non-metallic) five (5) feet outside the building; Motor

Driven Wheelbarrow & Concrete Buggy; Hyster Operator; Grout pump operator; Pump crete Assembler; Conveyor Assembler;

Core Drill Operator; Cement/Lime/Silica Clay Handler (Bulk or Bar); Pneumatic Spiker; Deck/Engine/Winch Operator;

Water Main & Cable Decking (Metallic or Non-metallic);

Remote Controlled Compactor

GROUP 3: Plasterer Tender; Mason Tender; Mortar Mixer; Welder

(Acetylene or Electric); Cutting Torch or Burner; Cement

Gun Operator; Scaffold Builder (When working for Plasterer or Mason)

GROUP 4: Dynamite Man

PAIN0156-002 04/01/2024

Painters:

BRUSH & ROLLER..............$ 29.62 18.32

DRYWALL FINISHERS...........$ 30.37 19.32

SPRAY, SANDBLAST, POWER

TOOLS, WATERBLAST & STEAM

CLEANING....................$ 30.62 19.32

FOOTNOTE A:

All Structures over 40? $0.75/ hour above base wage

All Structures over 75? $1.50/ hour above base wage

All Structures over 100? $2.50/ hour above base wage

PAIN0197-002 06/01/2024

CLAY, GREENE, OWEN, PARKE, PUTNAM, SULLIVAN, VERMILLION AND

VIGO COUNTIES:

Painters:

Brush & Roller..............$ 30.25 15.50

Drywall & Paper hangers

(with tools)................$ 31.25 15.50

Sandblasting................$ 32.25 15.50

-17-

Spray & Pot Man.............$ 30.75 15.50

FOOTNOTE A: $1.00 premium for work on structures over 40 ft.

above floor/ground level

$2.00 premium for work on structures over 100 ft above floor/ground level

PAIN1165-007 06/01/2024

GIBSON, POSEY, VANDERBURGH, WARRICK COUNTIES

Rates Fringes

GLAZIER..........................$ 32.86 19.34

PAIN1165-012 01/01/2024

CLAY; GREENE; OWEN; PARKE; PUTNAM; SULLIVAN; VERMILLION and

VIGO COUNTIES

GLAZIER..........................$ 34.03 20.05

PLAS0075-001 06/01/2017

CLAY, OWEN, PARKE, PUTNAM, VERMILLION AND VIGO COUNTIES:

CEMENT MASON/CONCRETE FINISHER...$ 25.75 13.50

PLAS0075-002 06/01/2017

GREENE and SULLIVAN COUNTIES

CEMENT MASON/CONCRETE FINISHER...$ 28.50 13.50

PLAS0566-001 04/01/2018

-18-

CEMENT MASON/CONCRETE FINISHER...$ 26.30 16.91

PLAS0692-001 06/01/2024

AREA #46

CLAY, GIBSON, GREENE, OWEN, PARKE, POSEY, PUTNAM, SULLIVAN,

VANDERBURGH, VERMILLION, VIGO and WARRICK COUNTIES

Rates Fringes

PLASTERER........................$ 30.50 17.62

PLUM0136-002 04/01/2024

REMAINING COUNTIES

Plumbers and Pipefitters.........$ 43.67 21.35

PLUM0157-001 01/01/2025

CLAY, GREENE, PARKE, PUTNAM (Part), SULLIVAN, VERMILLION and

Plumbers and Pipefitters.........$ 45.45 22.50

PLUM0440-001 06/04/2024

PUTNAM COUNTY (EAST OF ROAD 43 EXCEPT TERRITORY ON A EAST MILE

RADIUS FROM THE COURT HOUSE)

Plumbers and Pipefitters.........$ 46.50 19.89

ROOF0106-001 04/01/2023

REMAINING COUNTIES:

-19-

Roofers:

COMPOSITION.................$ 31.60 19.43

SLATE & TILE................$ 31.60 19.43

ROOF0119-001 09/01/2024

PUTNAM COUNTY

Roofers:.........................$ 31.00 14.21

ROOF0150-002 07/01/2024

CLAY, GREENE, OWEN, PARKE, SULLIVAN, VERMILLION AND VIGO

COUNTIES

Rates Fringes

ROOFER...........................$ 30.00 18.30

SFIN0669-002 04/01/2024

SPRINKLER FITTER.................$ 45.40 27.29

SHEE0020-018 07/01/2023

CLAY, GREENE, OWEN, PARKE, PUTNAM, SULLIVAN, VERMILLION, and

Sheet metal worker...............$ 39.53 22.92

HVAC Duct Work

SHEE0020-019 07/01/2023

GIBSON, POSEY, VANDERBURGH, and WARRICK COUNTIES

Sheet metal worker...............$ 34.58 29.98

HVAC Duct Work

-20-

TEAM0135-006 04/01/2024

CLAY, GREENE OWEN, PARKE, PUTNAM, SULLIVAN, VERMILLION, and

Truck drivers:

GROUP 1.....................$ 32.10 .42+a+b

GROUP 2.....................$ 32.60 .42+a+b

GROUP 3.....................$ 32.80 .42+a+b

GROUP 4.....................$ 32.95 .42+a+b

GROUP 5.....................$ 33.45 .42+a+b

A: $36.40 PER DAY & 450.00 PER WEEK.

TRUCK DRIVER CLASSIFICATIONS:

GROUP 1: Single Axle Trucks seven (7) cu.yds. or less than ten and 0ne-half (10 1/2) tons, dumpsters, scoop-mobiles five (5) cu. yds. and under or less than seven and one-half

(7 1/2) tons, mixer trucks three (3) cu.yds. and under, air compressors and welding machines, including those pulled by separate units, batch trucks-wet or dry-2""34-E batches or less, truck driver helpers, warehousemen, mechanic's helpers, greasers and tiremen, all pick-up trucks and other vehicles. Drivers on dumpsters or similar dumpsters, mounted on four

(4) wheel truck rated two (2) cu.yds. or less, and small pallet type fork-lift operator and drivers on pallet jacks or similar type equipment.

GROUP 2: Drivers on tandem axle eighteen (18) cu.yds.or twenty- four (24) tons gross, six (6) wheel trucks, Koehring or similar dumpsters, tract trucks, Euclids, hug bottom dumps, tournapulls, tournatrailers, tournarockers, or similar equipment when used for transportation purposes under nine (9) cu.yds. or less than thirteen and one-half

(13 1/2) tons, tandems and semi-trailer service trucks, mixer trucks over three (3) cu. yds. and including six and one-half (6

1/2) cu.yds., fork lift, four (4) wheel A frame trucks when used for transportation purposes, four (4) wheel winch trucks, pavement breakers, batch trucks - wet or dry - over

2 up to and including 4-""34-E"" batches two (2) men oil distributors, fork-lift under four (4) ton and vacuum trucks.

-21-

GROUP 3: Koehring or similar dumpsters, tract trucks, semi-trailer water trucks, Euclids, hug bottom dumps, tournapulls, tournatrailers, tournarockers, tractor trailers, tandems Q frame winch trucks, hydrolift trucks or similar equipment when used for transportation purposes, mixer trucks over six and one-half (6 1/2) cu.yds. batch trucks wet or dry over 4-""34-E"" batches single axle low boy trailers, and Contractor's mechanics when working on equipment operated by employees within this Bargaining

Unit. Six (6) wheel pole trailers and one (1) man oil distributors, fork- lift over four (4) ton and mobile mixers.

GROUP 4: Drivers on heavy equipment over sixteen (16) cu.yds. or twenty-four ton, such as Koehring or similar dumpsters, tract trucks, Euclids, hug bottom dumps, tournapulls, tournarockers or similar equipment wen used for transportation purposes, pole trailers over six (6) wheels, water pulls, low-boy trailers tandem axles, quad axle or more no-weight limitation, diseal and/or heavy equipment mechanics when working on equipment operated by employees with this Bargaining Unit.

GROUP 5: Mechanic furnishing his own tools.

TEAM0215-005 04/01/2024

GIBSON, POSEY, VANDERBURGH AND WARRICK COUNTIES:

Truck drivers:

GROUP 1.....................$ 27.08 21.45

GROUP 2.....................$ 27.54 21.45

GROUP 3.....................$ 27.76 21.45

GROUP 1 - Pickup Trucks, Winch Trucks, Warehouseman, Mechanic, Street sweepers, Single axle trucks

GROUP 2 - Tandem Trucks or Dump Trucks; Farm Tractor Pulling trailer; Bituminous Distributors, Pavement Breakers

GROUP 3 - Mixer Trucks, all types; Lowboys, all types; Semi-trucks, all types; All Tri-axle Dump Trucks; Articulated

End Dumps; End Dumps; Heavy Equipment Type Water Wagons;

Hazardous Waste Warehouseman; Hazardous Waste Driver; and

-22-

Drivers on equipment when not self-loaded or pusher loaded, such as Koehring or similar dumpsters, track trucks, Euclid bottom dump and hug bottom dump, Tournatrailers, Tournarockers or similar equipment.

WELDERS - Receive rate prescribed for craft performing operation to which welding is incidental.

Note: Executive Order (EO) 13706, Establishing Paid Sick Leave for Federal Contractors applies to all contracts subject to the

Davis-Bacon Act for which the contract is awarded (and any solicitation was issued) on or after January 1, 2017. If this contract is covered by the EO, the contractor must provide employees with 1 hour of paid sick leave for every 30 hours they work, up to 56 hours of paid sick leave each year.

Employees must be permitted to use paid sick leave for their own illness, injury or other health-related needs, including preventive care; to assist a family member (or person who is like family to the employee) who is ill, injured, or has other health-related needs, including preventive care; or for reasons resulting from, or to assist a family member (or person who is like family to the employee) who is a victim of, domestic violence, sexual assault, or stalking. Additional information on contractor requirements and worker protections under the EO is available at https://www.dol.gov/agencies/whd/government-contracts.

Unlisted classifications needed for work not included within the scope of the classifications listed may be added after award only as provided in the labor standards contract clauses

(29CFR 5.5 (a) (1) (iii)).

The body of each wage determination lists the classifications and wage rates that have been found to be prevailing for the type(s) of construction and geographic area covered by the wage determination. The classifications are listed in alphabetical order under rate identifiers indicating whether the particular rate is a union rate (current union negotiated rate), a survey rate, a weighted union average rate, a state adopted rate, or a supplemental classification rate.

http://www.dol.gov/agencies/whd/government-contracts

-23-

Union Rate Identifiers

A four-letter identifier beginning with characters other than

""SU"", ""UAVG"", ?SA?, or ?SC? denotes that a union rate was prevailing for that classification in the survey. Example:

PLUM0198-005 07/01/2024. PLUM is an identifier of the union whose collectively bargained rate prevailed in the survey for this classification, which in this example would be Plumbers.

0198 indicates the local union number or district council number where applicable, i.e., Plumbers Local 0198. The next number, 005 in the example, is an internal number used in processing the wage determination. The date, 07/01/2024 in the example, is the effective date of the most current negotiated rate.

Union prevailing wage rates are updated to reflect all changes over time that are reported to WHD in the rates in the collective bargaining agreement (CBA) governing the classification.

Union Average Rate Identifiers

The UAVG identifier indicates that no single rate prevailed for those classifications, but that 100% of the data reported for the classifications reflected union rates. EXAMPLE:

UAVG-OH-0010 01/01/2024. UAVG indicates that the rate is a weighted union average rate. OH indicates the State of Ohio.

The next number, 0010 in the example, is an internal number used in producing the wage determination. The date, 01/01/2024 in the example, indicates the date the wage determination was updated to reflect the most current union average rate.

A UAVG rate will be updated once a year, usually in January, to reflect a weighted average of the current rates in the collective bargaining agreements on which the rate is based.

Survey Rate Identifiers

The ""SU"" identifier indicates that either a single non-union rate prevailed (as defined in 29 CFR 1.2) for this classification in the survey or that the rate was derived by computing a weighted average rate based on all the rates reported in the survey for that classification. As a weighted average rate includes all rates reported in the survey, it may include both union and non-union rates. Example: SUFL2022-007

6/27/2024. SU indicates the rate is a single non-union prevailing rate or a weighted average of survey data for that classification. FL indicates the State of Florida. 2022 is the

-24-year of the survey on which these classifications and rates are based. The next number, 007 in the example, is an internal number used in producing the wage determination. The date, 6/27/2024 in the example, indicates the survey completion date for the classifications and rates under that identifier.

?SU? wage rates typically remain in effect until a new survey is conducted. However, the Wage and Hour Division (WHD) has the discretion to update such rates under 29 CFR 1.6(c)(1).

State Adopted Rate Identifiers

The ""SA"" identifier indicates that the classifications and prevailing wage rates set by a state (or local) government were adopted under 29 C.F.R 1.3(g)-(h). Example: SAME2023-007

01/03/2024. SA reflects that the rates are state adopted. ME refers to the State of Maine. 2023 is the year during which the state completed the survey on which the listed classifications and rates are based. The next number, 007 in the example, is an internal number used in producing the wage determination.

The date, 01/03/2024 in the example, reflects the date on which the classifications and rates under the ?SA? identifier took effect under state law in the state from which the rates were adopted.

WAGE DETERMINATION APPEALS PROCESS

1) Has there been an initial decision in the matter? This can be:

a) a survey underlying a wage determination

b) an existing published wage determination

c) an initial WHD letter setting forth a position on a wage determination matter

d) an initial conformance (additional classification and rate) determination

On survey related matters, initial contact, including requests for summaries of surveys, should be directed to the WHD Branch of Wage Surveys. Requests can be submitted via email to davisbaconinfo@dol.gov or by mail to:

Branch of Wage Surveys

Wage and Hour Division

U.S. Department of Labor

200 Constitution Avenue, N.W.

mailto:davisbaconinfo@dol.gov

-25-

Washington, DC 20210

Regarding any other wage determination matter such as conformance decisions, requests for initial decisions should be directed to the WHD Branch of Construction Wage Determinations.

Requests can be submitted via email to BCWD-Office@dol.gov or by mail to:

Branch of Construction Wage Determinations

Wage and Hour Division

U.S. Department of Labor

200 Constitution Avenue, N.W.

2) If an initial decision has been issued, then any interested party (those affected by the action) that disagrees with the decision can request review and reconsideration from the Wage and Hour Administrator (See 29 CFR Part 1.8 and 29 CFR Part 7).

Requests for review and reconsideration can be submitted via email to dba.reconsideration@dol.gov or by mail to:

Wage and Hour Administrator

U.S. Department of Labor

The request should be accompanied by a full statement of the interested party's position and any information (wage payment data, project description, area practice material, etc.) that the requestor considers relevant to the issue.

3) If the decision of the Administrator is not favorable, an interested party may appeal directly to the Administrative

Review Board (formerly the Wage Appeals Board). Write to:

Administrative Review Board

U.S. Department of Labor

Washington, DC 20210.

END OF GENERAL DECISION"

W912QR-22002077A_CERTFinal_Specs-000 mailto:BCWD-Office@dol.gov mailto:dba.reconsideration@dol.gov

P2#: 500352 Indiana Air National Guard Small Arms Range Terre Haute, IN

SECTION 01 02 10.00 06

PROJECT DESCRIPTION AND DESIGN REQUIREMENTS

09/17

Amendment 0002

PART 1 DESIGN OBJECTIVES

1.1 REFERENCES

The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only. Note that the editions of the specified references shall be in accordance with the edition of UFC 1-200-01, DoD Building Code, in effect at the time of the issuance of the Design Build Request for Proposal (RFP) per Section 1-3.1 Implementation, Administration, and Enforcement of UFC 1-200-01. All Air Force Engineering Technical Letters (ETL) shall be utilized in the design and construction of this project.

Department of Defense Memorandum, "Electrification of Standard Building Operations," dated 29 March 2023 is not applicable to this project.

AMERICAN CONCRETE INSTITUTE (ACI)

ACI 302.1R-15 Guide to Concrete Floor and Slab Construction

AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)

ANSI/AWWA C105/A21.5 Polyethylene Encasement for Ductile-Iron Pipe Systems

ANSI/AWS D1.1 Structural Welding Code - Steel

ANSI/BHMA A156.1 Butts and Hinges

ANSI/BHMA A156.2 Bored and Preassembled Locks and Latches

ANSI/BHMA A156.3 Exit Devices

ANSI/BHMA A156.4 Door Controls-Closers

ANSI/BHMA A156.16 Auxiliary Hardware

ANSI/BHMA A156.6 Architectural Door trim

ANSI/BHMA A156.21 Thresholds

ANSI/BHMA A156.22 Door Gasketing and Edge Seal Systems

ANSI C2 National Electrical Safety Code

AMERICAN SOCIETY OF CIVIL ENGINEERS (ASCE)

ASCE 7 Minimum Design Loads for Buildings and

SECTION 01 02 10.00 06 Page 1 Certified Final Submittal - Amendment 0002

Other Structures

AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR-CONDITIONING

ENGINEERS (ASHRAE)

ASHRAE 62.1 Ventilation for Acceptable Indoor Air Quality

ASHRAE 90.1 Energy Standard for Buildings except Low-Rise Residential Buildings

ASTM INTERNATIONAL (ASTM)

ASTM A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

ASTM A325 Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

ASTM A36 Carbon Structural Steel

ASTM A490 Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

ASTM A500 Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes

ASTM A53 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless

ASTM A615 Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement

ASTM A641/A641M Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire

ASTM A653 Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

ASTM A653/A653M Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

ASTM A706 Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement

ASTM A924 Steel Sheet, Metallic-Coated by the Hot-Dip Process

ASTM A924/A924M Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process

ASTM A992 Structural Steel Shapes

ASTM C920 Standard Specification for Elastomeric

SECTION 01 02 10.00 06 Page 2

Joint Sealants

ASTM C1036 (2021) Standard Specification for Flat Glass

ASTM C1177/C1177M Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing

ASTM A1064/A1064M Standard Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete

ASTM B209 (2014) Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

ASTM B209M Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)

ASTM C90 Standard Specification for Loadbearing Concrete Masonry Units

ASTM C1396 Gypsum Board

ASTM C475 Joint Compound and Joint Tape for Finishing Gypsum Board

ASTM C578 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

ASTM C591 Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation

ASTM C665 Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing

ASTM C834 (2017; R 2023) Standard Specification for Latex Sealants

ASTM C840 Application and Finishing of Gypsum Board

ASTM C1396/C1396M (2017) Standard Specification for Gypsum Board

ASTM D1557 Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3) (2700 kN-m/m3)

ASTM D1751 Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Non-extruding and Resilient Bituminous Types)

ASTM D1752 Preformed Sponge Rubber Cork and Recycled PVC Expansion

ASTM E283 Standard Test Method for Determining the Rate of Air Leakage Through Exterior

SECTION 01 02 10.00 06 Page 3

Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen

ASTM E331 (2000; R 2023) Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference

ASTM E84 Surface Burning Characteristics of Building Materials

ELECTRONIC INDUSTRIES ALLIANCE (EIA)

EIA/TIA 568B Commercial Building Telecommunications Cabling Standard

EIA/TIA 569 Pathways and Spaces

EIA/TIA 569A Commercial Buildings Telecommunications Pathways and Spaces

EIA/TIA 569B Commercial Buildings Telecommunications Pathways and Spaces

EIA/TIA 607-D Grounding and Bonding Requirements

INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS (IEEE)

IEEE 1584 (2018; E 2019) Guide for Performing Arc-Flash Hazard Calculations

IEEE 1584.1 (2022) Guide for the Specification of Scope and Deliverable Requirements for an Arc-Flash Hazard Calculation Study

NACE INTERNATIONAL (NACE)

NACE SP-0169 Control of External Corrosion on Underground or Submerged Metallic Piping Systems

NACE SP-0286 Electrical Isolation of Cathodically Protected Pipelines

NACE SP-0185 Extruded Polyolefin Resin Coating Systems with Soft Adhesives for Underground or Submerged Pipe

NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)

NFPA 101 Life Safety Code

NFPA 110 Emergency and Standby Power Systems

NFPA 13 Installation of Sprinkler Systems

NFPA 70 National Electrical Code

SECTION 01 02 10.00 06 Page 4

NFPA 72 National Fire Alarm and Signaling Code

NFPA 780 Installation of Lightning Protection Systems

UNIFIED FACILITIES CRITERIA (UFC)

UFC 1-200-01 DoD Building Code

UFC 1-200-02 High Performance and Sustainable Building Requirements

UFC 3-101-01 Architecture

UFC 3-120-01 Sign Standards

UFC 3-201-01 Civil Engineering

UFC 3-230-01 Water Storage and Distribution

UFC 3-410-01 Heating, Ventilating, and Air Conditioning Systems

UFC 3-410-02 Lonworks Direct Digital Control for HVAC and Other Local Building Systems

UFC 3-240-01 Wastewater Collection and Treatment

UFC 3-240-02 Domestic Wastewater Treatment

UFC 3-401-01 Mechanical Engineering

UFC 3-420-01 Plumbing Systems

UFC 3-501-01 Electrical Engineering

UFC 3-520-01 Interior Electrical Systems

UFC 3-530-01 Interior and Exterior Lighting and Controls

UFC 3-550-01 Exterior Electrical Power Distribution

UFC 3-575-01 Lightning and Static Electricity Protection Systems

UFC 3-580-01 Telecommunications Building Cabling Systems Planning and Design

UFC 3-600-01 Fire Protection Engineering for Facilities

UFC 4-010-01 DoD Minimum Antiterrorism Standards for Buildings

UFC 4-010-06 Cybersecurity of Facility-Related Control Systems

UFC 4-021-01 Design and O&M: Mass Notification Systems

UFC 4-179-02 Small Arms Ranges

SECTION 01 02 10.00 06 Page 5

FC 4-179-03F Air Force Indoor Small Arms Firing Range

UNDERWRITERS LABORATORIES (UL)

UL 2017 General-Purpose Signaling Devices and Systems

UL 305 Panic Hardware

UL 67 Panelboards

UL 864 Control Units and Accessories for Fire Alarm Systems

UL 869A Service Equipment

1.2 SCOPE OF WORK

Design and construction shall comply with the requirements contained in this Request for Proposals (RFP). The design and technical criteria contained and cited in this RFP establish minimum standards for design and construction quality. The Designers of Record shall use the Unified Facilities Guide Specifications (UFGS) and the requirements contained in this RFP to fully develop the technical specifications and construction drawings. The objective of this solicitation is to obtain a single, durable, functional building complete and adequate for assignment as an indoor small arms range and combat arms training and maintenance (CATM).

The building and site drawings included in this RFP illustrate the conceptual design of the project. Site and floor plans provided shall be followed by the Design/Build Contractor to comply with the end User functional needs. The building elevation provided shall be further developed to achieve architectural compatibility with the Base Facility Standard. No particular structural system is selected or recommended by the government; therefore, the structural design is the contractor's responsibility.

This contract shall consist of a base bid for the design and construction of the 10-lane small arms range with a 1,350 square foot CATM building, including administrative and operations facilities complete with associated utilities, storm drainage, communications, electric, HVAC, lightning protection, fire protection/alarm system, paving, sidewalks, curbs, gutters, access drives, exterior lighting, grading, and physical security requirements.

The contract also includes the following bid options:

Bid Option #1 - All additional work, labor, materials, and equipment required to design a 10,500 SF 14-Lane Small Arms Firing Range as described in this RFP.

Bid Option #2 - All additional work, labor, materials, and equipment required to construct a 10,500 SF 14-Lane Small Arms Firing Range as described in this RFP.

Bid Option #3 - All additional work, labor, materials, and equipment required to design 1,800 SF CATM Facility as described in this RFP.

SECTION 01 02 10.00 06 Page 6

Bid Option #4 - All additional work, labor, materials, and equipment required to construct 1,800 SF CATM Facility as described in this RFP.

Bid Option #5 - All additional work, labor, materials, and equipment required to design the Furniture, Fixture, and Equipment.

Bid Option #6 - All additional work, labor, materials, and equipment required to procure and install the Furniture, Fixture, and Equipment.

Bid Option #7 - All additional work, labor, materials, and equipment required to design the target retrieval system.

Bid Option #8 - All additional work, labor, materials, and equipment required to procure and install the target retrieval system.

Bid Option #9 - All additional work, labor, materials, and equipment required for full detailed design of the Access Control System.

Bid Option #10 - All additional work, labor, materials, and equipment required to procure and install the Access Control System.

Amdt. #0002******************************************************************

Bid Option #11 -All additional work, labor, and materials required to design the FFE of additional 450 SF.

Bid Option #12 -All additional work, labor, materials, and equipment required to procure and install the FFE of additional 450 SF.

Bid Option #13 -All additional work, labor, and materials required to design the target retrieval system of additional 4-lanes.

Bid Option #14 -All additional work, labor, materials, and equipment required to procure and install the target retrieval system of additional 4-lanes.

Bid Option #15 -All additional work, labor, and materials required for full detail design of the Access Control System of additional 4-lanes.

Bid Option #16 -All additional work, labor, materials, and equipment required to procure and install full Access Control System of additional 4-lanes.

Bid Option #17 -All additional work, labor, and materials required for full detail design of the Access Control System of additional 450 SF.

Bid Option #18 -All additional work, labor, materials, and equipment required to procure and install full Access Control System of additional

450 SF.

******************************************************************Amdt. #0002

1.3 APPLICABLE CRITERIA

Applicable design and construction criteria is specifically indicated, but not limited to that mentioned in this LRL Section 01 02 10.00 06.

Criteria shall be taken from the most current references as of the date of issue of the RFP, unless noted otherwise. Referenced codes and standards are minimum acceptable criteria. Administrative, contractual, and

SECTION 01 02 10.00 06 Page 7 procedural features of the contract shall be as described in other sections of the RFP.

1.4 SPECIFICATIONS

The technical specifications shall be developed from the Unified Facilities Guide Specifications (UFGS) by the Designers of Record. The Louisville District (LRL) versions of the UFGS shall be used in all cases where applicable. If LRL or UFGS versions are not available , the Designer of Record shall develop one using a SpecsIntact template. See LRL Section 01 03 00.00 06 DESIGN SUBMISSION REQUIREMENTS AFTER AWARD for further technical specification preparation requirements.

1.5 DESIGN QUALITY

The main objectives of this solicitation are to obtain a 10-lane small arms range with a 1,350 square foot CATM including associated site development within funds available, and to maximize design and materials quality. Design and materials quality is achieved through the integration of utility systems within the building and on the site, selection of building systems for low-cost maintenance and operation, and an overall balance of aesthetics and functionality within the parameters provided herein.

1.6 DESIGN FREEDOM

Requirements stated and illustrated in this RFP are minimums. Innovative, creative, or cost-saving proposals which meet or exceed these requirements are encouraged and shall be considered during the design charette and design submittal reviews. The drawings provided establish project floor area requirements and spatial relationships that have been reviewed for user function and preliminary code compliance. Floor and site plans may change with government approval to enhance design, comply with codes, incorporate options, include betterments, or support constructability.

1.7 ENERGY STANDARD COMPLIANCE

The building shall comply with the provisions of ASHRAE 90.1 . As a separate part or section of the Design Analysis, demonstrate compliance with ASHRAE 90.1 using calculations, vendor literature, equipment catalog sheets, compliance forms, worksheets, and narrative descriptions of the building envelope, HVAC systems, service water heating, electrical power, lighting, and other equipment and systems.

1.8 ACCESSIBILITY REQUIREMENTS

The 10-lane small arms range with a 1,350 square foot CATM facility shall be fully accessible to physically disabled persons and shall conform to the ABA Accessibility Guidelines for Buildings and Facilities.

1.9 FORCE PROTECTION & ANTI-TERRORISM CONSIDERATIONS

Project design and construction shall comply with the Department of Defense Minimum Antiterrorism Standards for Buildings which is available on the internet at http://www.wbdg.org/ccb/browse_cat.php?o=29&c=4 Unified Facilities Criteria (UFC) for UFC 4-010-01 . Mass notification systems shall be in accordance with UFC 4-021-01 .

SECTION 01 02 10.00 06 Page 8

1.