RFQ W912PQ23Q0036 Amendment 0002 Conformed Copy.pdf

SEE ADDENDUM

(No Collect Calls)

W912PQ23Q0036 03-Aug-2023

b. TELEPHONE NUMBER

518-786-4739

8. OFFER DUE DATE/LOCAL TIME

11:00 AM 31 Aug 2023

5. SOLICITATION NUMBER 6. SOLICITATION ISSUE DATE

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

STANDARD FORM 1449 (REV. 2/2012)

Prescribed by GSA – FAR (48 CFR) 53.212

(TYPE OR PRINT)

(SIGNATURE OF CONTRACTING OFFICER)

ADDENDA ARE

26. TOTAL AWARD AMOUNT (For Gov t. Use Only )

23.

CODE 10. THIS ACQUISITION IS

SUCH ADDRESS IN OFFER

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT

BELOW IS CHECKED

TELEPHONE NO.

W912PQ9. ISSUED BY

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a. UNLESS BLOCK

7. FOR SOLICITATION

INFORMATION CALL:

a. NAME

ANDREW EMRICH

2. CONTRACT NO. 3. AWARD/EFFECTIVE DATE 4. ORDER NUMBER

(TYPE OR PRINT)

30b. NAME AND TITLE OF SIGNER 30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER

30a. SIGNATURE OF OFFEROR/CONTRACTOR 31a.UNITED STATES OF AMERICA

0 27a. SOLICITATION INCORPORATES BY REFERENCE FAR 52.212-1. 52.212-4. FAR 52.212-3. 52.212-5 ARE ATTACHED.

25. ACCOUNTING AND APPROPRIATION DATA

1. REQUISITION NUMBER

20.

ADDITIONAL SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED.

OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, AND 30

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

0011924781

ARE NOT ATTACHED

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA ARE ARE NOT ATTACHED

(BLOCK 5), INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE

SET FORTH HEREIN, IS ACCEPTED AS TO ITEMS:

. YOUR OFFER ON SOLICITATION

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN

% FOR:SET ASIDE:UNRESTRICTED OR X

SMALL BUSINESS

17a.CONTRACTOR/ CODE FACILITY

OFFEROR CODE

USPFO NY PURCHASING & CONTRACTING

330 OLD NISKAYUNA ROAD

LATHAM NY 12110-2224

18a. PAYMENT WILL BE MADE BY CODE

RATED ORDER UNDER

DPAS (15 CFR 700)

13a. THIS CONTRACT IS A

13b. RATING

CODE15. DELIVER TO CODE W56PPG 16. ADMINISTERED BY

12. DISCOUNT TERMS11. DELIVERY FOR FOB DESTINA-

TION UNLESS BLOCK IS

MARKED

SEE SCHEDULE

14. METHOD OF SOLICITATION

RFQ IFB RFPX

JFHQ-NY, ATTN: MNFE

MAJ TRENTON ROESKE

6900 THOMPSON RD

SYRACUSE NY 13211

TEL: FAX:

FAX:

TEL: SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

X 8(A)

HUBZONE SMALL

BUSINESS

SIZE STANDARD:

$22,000,000

NAICS:

238290

X

OFFER DATED

29. AWARD OF CONTRACT: REF.

DELIVER ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY

COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND

EMAIL:

TEL:

31c. DATE SIGNED

SEE SCHEDULE

SCHEDULE OF SUPPLIES/ SERVICESITEM NO. QUANTITY UNIT UNIT PRICE AMOUNT

24.22.21.19.

WOMEN-OWNED SMALL BUSINESS (WOSB)

ELIGIBLE UNDER THE WOMEN-OWNED

SMALL BUSINESS PROGRAM

EDWOSB

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS

(CONTINUED)

PAGE 2 OF81

ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED: ______________________________________________________

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED INSPECTED

32b. SIGNATURE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32c. DATE 32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT

REPRESENTATIVE

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE 32f . TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

37. CHECK NUMBER

FINALPARTIALCOMPLETE

36. PAYMENT35. AMOUNT VERIFIED

CORRECT FOR

34. VOUCHER NUMBER

FINAL

33. SHIP NUMBER

PARTIAL

38. S/R ACCOUNT NUMBER 39. S/R VOUCHER NUMBER 40. PAID BY

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT

41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER 41c. DATE

42a. RECEIVED BY (Print)

42b. RECEIVED AT (Location)

42c. DATE REC'D (YY/MM/DD) 42d. TOTAL CONTAINERS

STANDARD FORM 1449 (REV. 2/2012) BACK

Prescribed by GSA – FAR (48 CFR) 53.212

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

SEE SCHEDULE

20.

SCHEDULE OF SUPPLIES/ SERVICES

21.

QUANTITY UNIT

22. 23.

UNIT PRICE

24.

AMOUNT

19.

ITEM NO.

W912PQ23Q0036

Section SF 1449 - CONTINUATION SHEET

PERFORMANCE WORK STATEMENT (PWS)

FOR

Field Maintenance Shop (FMS)-5 Facility Upgrade Services

6900 Thompson Rd, Syracuse, NY 13211

1.0 General:

1.1 Scope: The contractor shall provide all personnel, equipment, tools, materials, supervision, and quality control necessary, except as specified in Paragraph 3.0 as Government Furnished, to perform various FMS-5 facility upgrades, as defined in this

PWS.

1.1.1 Objectives: FMS-5 at the Syracuse Enclave on the Hancock Field Air Base requires replacement of the vehicle exhaust system so that each of the five exhaust lines are individually piped to the exterior. Provide new exterior doors, frames, and hardware to all exterior single and double doors. Provide underground conduit to the man gate from the maintenance shop. Replace concrete apron in front of the supply room so that water pitches away from the building.

1.2 Background: FMS-5 is an NY Army National Guard (NYARNG) facility in the Syracuse Enclave on the Hancock Field Air Base.

1.3 Period of Performance (PoP): The Period of Performance shall be 1 Year from award date.

1.4 General Information:

1.4.1 Place and Performance of Services: The contractor shall provide services between the hours of 0730-1600 hours on Monday through Friday, except on recognized US holidays or when the Government facility/installation is closed due to local or national emergencies, administrative closings, or similar Government-directed facility/installation closings. Performance shall be at 6900 Thompson Rd, Syracuse, NY 13211. The contractor shall at all times maintain an adequate work force for the uninterrupted performance of all tasks defined within this PWS when the Government facility/installation is not closed for the above reasons. When hiring personnel, the contractor shall keep in mind that the stability and continuity of the work force are essential. Teleworking is not authorized.

1.4.1.1 Telework: The Government does not permit the contractor to telework in support of this requirement. In furtherance of Continuity of Operations Planning

(COOP), a telework program may be enacted to ensure that the Government's mission-critical operations stay operational during times of national emergency or incidents of national significance. Telework shall be at no additional cost to the Government.

1.4.1.2 Unscheduled gate closures by the Security Police may occur at any time causing all personnel entering or exiting a closed installation to experience a delay. This cannot be predicted or prevented. Contractors are not compensated for unexpected closures or delays. Vehicles operated by contractor personnel are subject to search pursuant to applicable regulations. Any moving violation of any applicable motor vehicle regulation may result in the termination of the contractor employee’s installation driving privileges.

1.4.1.3 The contractor’s employees shall become familiar with and obey the regulations of the installation; including fire, traffic, safety and security regulations while on the installation. Contractor employees should only enter restricted areas when required to do so and only upon prior approval. All contractor employees shall carry proper identification with them at all times and shall be subject to such checks as may be deemed necessary. The contractor shall ensure compliance with all regulations and orders of the installation, which may affect performance. The Government reserves the right to direct the removal of an employee from Government property or revoke access to Government systems for misconduct, security reasons, or any overt evidence of communicable disease. Removal of contractor employees for reasons stated above does not relieve the Contractor from responsibility for total performance of this contract.

1.4.2 Recognized Holidays: The following are recognized United States (US) holidays.

The contractor shall not perform services on these days:

1.4.2.1 New Year’s Day: January 1st

1.4.2.2 Martin Luther King, Jr.’s Birthday

1.4.2.3 President’s Day

1.4.2.4 Memorial Day

1.4.2.5 Juneteenth National Independence Day: June 19th

1.4.2.6 Independence Day: July 4th

1.4.2.7 Labor Day

1.4.2.8 Columbus Day

1.4.2.9 Veteran’s Day: November 11th

1.4.2.10 Thanksgiving Day

1.4.2.11 Christmas Day: December 25th

1.4.3 Quality Control (QC): The contractor shall develop and maintain an effective QC Plan (QCP) to ensure services are performed in accordance with this PWS. The contractor shall develop and implement procedures to identify, prevent, and ensure non-recurrence of defective services. The contractor’s QCP is the means by which it assures itself that its work complies with the requirements of the contract. As a minimum, the contractor shall develop QC procedures that address the areas identified in Technical Exhibit 1, Performance Requirements Summary (PRS). A list of deliverables can be found in Technical Exhibit (TE) 2, Deliverables Schedule. A final QCP shall be submitted to the Contracting Officer Representative (COR) NLT 10 days after contract award. After acceptance of the QCP, the contractor shall obtain the Contracting Officer’s (KO’s) acceptance in writing of any proposed changes to its QCP.

1.4.4 Quality Assurance (QA): The Government will evaluate the contractor’s performance under this contract in accordance with the Quality Assurance Surveillance Plan (QASP). This plan is primarily focused on what the Government will do to ensure that the contractor has performed in accordance with the performance standards. It defines how the performance standards will be applied, the frequency of surveillance, and acceptable quality level(s) or defect rate(s).

1.4.5 Installation Access and Security Requirements. The contractor shall comply with all applicable installation/facility access and local security policies and procedures, which may be obtained from the COR. The contractor and all associated subcontractor employees shall provide all information required for background checks to meet installation access requirements to be accomplished by installation Provost Marshal Office, Director of Emergency Services, or Security Office. The contractor shall ensure compliance with all personal identity verification requirements as directed by Department of Defense (DoD), Headquarters Department of Army (HQDA) and/or local policy (see PWS 6.0). Should the Force Protection Condition (FPCON) change, the Government may require changes in contractor security matters or processes.

1.4.5.2 For contractors that do not require a CAC, but require access to a DoD facility or installation: Contractor and all associated sub-contractors employees shall comply with adjudication standards and procedures using the National Crime Information Center Interstate Identification (NCIC-III) and Terrorist Screening Database (TSDB) (Army Directive 2014-05), and applicable installation, facility and area commander installation/facility access, and local security policies and procedures (provided by a Government representative).

1.4.5.3 Awareness Training (AT) Level 1: N/A

1.4.5.5 Communications Security/Information Technology (COMSEC/IT) Security. All communications with DoD organizations are subject to COMSEC review. All telephone communications networks are continually subject to intercept by unfriendly intelligence organizations. DoD has authorized the military departments to conduct COMSEC monitoring and recording of telephone calls originating from, or terminating at, DoD organizations. Therefore, the contractor is advised that any time contractor personnel place or receive a call they are subject to COMSEC procedures. The contractor shall ensure wide and frequent dissemination of the above information to all employees dealing with DoD information. The contractor shall abide by all Government regulations concerning the authorized use of the Government's computer network, including the restriction against using the network to recruit Government personnel or advertise job openings.

1.4.5.11 OPSEC Training: N/A

1.4.6 Physical Security. The contractor shall safeguard all Government property provided for contractor use. At the close of each work period, Government facilities, equipment and materials shall be secured.

1.4.7 Special Qualifications: The contractor shall ensure all employees possess all required licenses including all electrical connections will be made by a New York State Certified Electrician for the performance of this contract. This does not include education or other qualifications for the position in which the contractor employee is performing, dress codes, or other information. (NOTE: The Government does not provide training to contractors. Contractors must ensure that any personnel performing under a contract are fully trained, licensed, certified, and otherwise qualified to provide services.)

1.4.8 Post Award Conference/Periodic Progress Meetings: The contractor agrees to attend any post award conference convened by the KO in accordance with FAR 42.5.

The KO, COR and other Government personnel, as appropriate, may meet periodically with the contractor to review the contactor’s performance. At these meetings, the KO will apprise the contractor of how the Government views the contractor’s performance and the contractor shall apprise the Government of problems, if any, being experienced.

The contractor shall resolve outstanding issues raised by the Government. Contractor attendance at these meetings shall be at no additional cost to the Government.

1.4.9 Contract Manager (CM): The contactor shall designate a CM who shall ensure performance under this contract. The name of this person, and an alternate who shall act for the contractor when the CM is absent, shall be designated in writing to the KO.

The CM or alternate shall have full authority to act for the contractor on all contract matters relating to daily operation of this contract. The CM shall work through the COR, to resolve issues, receive technical instructions, and ensure adequate performance of services. The CM shall ensure that contractor employees do not perform any services outside the scope of the contract without an official modification issued by the KO. The CM shall ensure contractor employees understand that services performed outside the scope of the contract are performed wholly at the expense of the contractor.

1.4.10 Identification of Contractor Employees: All contractor personnel attending meetings, answering Government telephones and working in other situations where their contractor status is not obvious to third parties are required to identify themselves as such to avoid creating an impression that they are Government employees. The contractor shall ensure that all documents or reports produced by contractor personnel are suitably marked as contractor products or that contractor participation is appropriately disclosed. The contractor’s status as a “contractor” shall be predominantly displayed in all correspondence types (to include signature blocks on e-mail) and dealings with Government or non-Government entities. Contractor personnel shall wear identification badges distinguishing themselves as such. The badges shall have the company name, employee name and the word “contractor” displayed.

1.4.10.1 The contractor shall retrieve all identification media (including vehicle passes) from its employees who depart employment for any reason. The contractor shall return all identification media (i.e., badges and vehicles passes) to the Air Base Security Office within 14 days of an employee’s departure.

1.4.11. Combating Trafficking in Persons: The United States Government has adopted a zero tolerance policy regarding trafficking in persons. Contractors and contractor employees shall not engage in severe forms of trafficking in persons during the period of performance of the contract; procure commercial sex acts during the period of performance of the contract; or use forced labor in the performance of the contract. The Contractor shall notify its employees of the United States Government’s zero tolerance policy, the actions that will be taken against employees for violations of this policy. The contractor shall take appropriate action, up to and including termination, against employees or subcontractors that violate the US Government policy as described at

FAR 22.17.

1.4.14 Organizational Conflicts of Interest (OCI): The contractor and subcontractor personnel performing services under this contract may receive, have access to or participate in the development of proprietary or source selection information (e.g., cost or pricing information, budget information or analyses, specifications or work statements, etc.) or perform evaluation services which may create a current or subsequent OCIs, as defined in FAR Subpart 9.5. The contractor shall notify the KO immediately whenever it becomes aware that such access or participation may result in any actual or potential OCI and shall promptly submit a plan to the KO to avoid or mitigate any such OCI. The contractor’s mitigation plan will be determined to be acceptable solely at the discretion of the KO. In the event the KO unilaterally determines that any such OCI cannot be satisfactorily avoided or mitigated, the KO may impose other remedies as he or she deems necessary, including prohibiting the contractor from participation in subsequent contracted requirements which may be affected by the OCI.

2.0 Definitions and Acronyms:

2.1 Definitions:

2.1.1 Contractor: A supplier or vendor awarded a contract to provide specific supplies or service to the Government. The term used in this contract refers to the prime.

2.1.2 Defective Service: A service output that does not meet the standard of performance associated with the PWS.

2.1.3 Deliverable: Anything that can be physically delivered and includes non-manufactured things such as meeting minutes or reports.

2.1.4 Key Personnel: Contractor personnel that are evaluated in a source selection process and that may be required to be used in the performance of a contract by the PWS. When key personnel are used as an evaluation factor in best value procurement, an offer can be rejected if it does not have a firm commitment from the persons that are listed in the proposal.

2.1.5 Physical Security: Actions that prevent the loss or damage of Government property.

2.1.6 Quality Assurance: The Government procedures to verify that services being performed by the Contractor are performed according to acceptable standards.

2.1.7 Quality Assurance Surveillance Plan (QASP): An organized written document specifying the surveillance methodology to be used for surveillance of contractor performance.

2.1.8 Quality Control: All necessary measures taken by the Contractor to ensure that the quality of an end product or service shall meet contract requirements.

2.1.9 Subcontractor: One that enters into a contract with a prime contractor. The Government does not have privity of contract with the subcontractor.

2.2 Acronyms:

AEI Army Enterprise Infostructure AR Army Regulation AT/OPSEC Antiterrorism/Operational Security BI Background Investigation CM Contract Manager COR Contracting Officer Representative DA Department of the Army DD254 Department of Defense Contract Security Classification Specification DFARS Defense Federal Acquisition Regulation Supplement DoD Department of Defense DSCA Defense Counterintelligence and Security Agency FAR Federal Acquisition Regulation GFP/M/E/S Government Furnished Property/Material/Equipment/Services HQDA Headquarters, Department of the Army HSPD Homeland Security Presidential Directive IA Information Assurance IS Information System(s) KO Contracting Officer NGB National Guard Bureau OCI Organizational Conflict of Interest PII Personally Identifiable Information PIPO Phase In/Phase Out POC Point of Contact PRS Performance Requirements Summary PWS Performance Work Statement QA Quality Assurance

QASP Quality Assurance Surveillance Plan QC Quality Control QCP Quality Control Program SCR Service Contract Reporting SSN Social Security Number TE Technical Exhibit USD(I) Under Secretary of Defense for Intelligence

3.0 Government Furnished Property, Material, Equipment and Services (GFP/M/E/S):

The Government will provide the property, material, equipment, and/or services listed below solely for the purpose of performance under this contract:

3.1 Property: Not Applicable

3.2 Materials: Not Applicable

3.3 Equipment: Not Applicable

3.4 Services: Not Applicable

3.5 Utilities: All utilities in the facility will be available for the contactor’s use in the performance of this contract. The contractor shall instruct employees in utilities conservation practices. The contractor shall operate under conditions that preclude the waste of utilities, which include turning off the water faucets or valves after using the required amount.

3.6 Trash Removal: The Contractor is responsible for removal of all trash, waste, or other packaging material from the site and installation. The Contractor will NOT utilize the installation dumpsters or other trash or waste receptacles.

4.0 Contractor Furnished Property, Materials, and Equipment (CFP/M/E):

4.1 General: Except for those items specifically stated to be Government-Furnished in Paragraph 3.0, the contractor shall furnish everything required to perform these services as indicated in Paragraph 1.1.

4.1.1 Testing: Contractor to provide final CFM testing of vehicle exhaust system at the intake nozzle. Utilize an anemometer to measure the exhaust ventilation airflow velocity.

The required reading needs to be over 900 CFM. The recommended procedure is to take velocity readings at multiple points across the nozzle opening. Average these readings to calculate the average face velocity and then multiply by the area of the nozzle opening.

4.2 Warranties:

4.2.1 Door Closers: Ten-year minimum manufacturer’s warranty for door closers.

4.2.2 Locksets: Three-year minimum manufacturer’s warranty for locksets.

5.0 Requirements: The contractor shall:

5.1. Contractor is responsible to verify field measurements and device counts prior to quote submission.

5.2. Remove four double steel exterior doors and frames from existing locations as identified on document “Field Maintenance Shop #5 Provide Various Improvements.PDF”.

5.3. Replace four double steel exterior doors and frames to include new door closers and panic bar hardware.

5.4. Remove six single steel exterior doors and frames as identified on document “Field Maintenance Shop #5 Provide Various Improvements.PDF

5.5. Replace five single steel exterior doors and frames to include new door closers and panic bar hardware. The four bay doors have a wire inlayed transom window and a transom window above the door that is a part of the frame. Two of the doors do not have any transom windows (see attached document for floor plan and photo descriptions).

5.6. Provide at the eastern main entrance a single steel exterior door and frame that accepts magnetic lock hardware. (Magnetic lock and wiring to be completed by facility) Provide new door closers and panic hardware. Lock to be same as other doors. Frame has an overhead transom window and a side transom window.

5.7. Key all locks the same. Best Lock is brand used by the facility. Provide six keys to the government representative (COR).

5.8. Door closers: Door closers shall be a hold open style and sized appropriately for the doors they are installed on. Grade 2 or 3 for heavy use. Closer arms are to be non-handed and of forged steel. Provide all-weather fluid to eliminate seasonal adjustment of closer speed. Provide powder coated closer body, arm, and adapter plate.

5.9. Panic bar hardware: Panic bar hardware shall be ADA compliant and non-handed.

Panic hardware shall be a touch-bar style. Do not use cross-bar style. Exterior levers and interior panic hardware to be installed 3 feet 2 inches from finished floor or as by current international building and fire codes.

5.10. Steel door frames: Minimum 16 gage steel with integral exposed flange not less than 1 inch wide around the perimeter and anchorage for concrete/masonry as adjustable metal masonry anchors. Frame supports to be galvanized and compatible with steel door frames complying with ASTM A 153, Class B. Anchors, bolts, and other fasteners to galvanized and comply with ASTM A 153, Class C or D as applicable.

5.11. Steel doors: Flush type and minimum 14 gage steel with concealed type set to open a minimum of 135 degrees with finish to match existing.

5.12. For all doors, provide a means to stop rain runoff from leaking into the building over the threshold. Current issue is that water leaks into the building via the doorway threshold. This solution cannot cause a tripping hazard.

5.13. Excavate the concrete and a portion of the asphalt in front of the supply room doors.

Compact subbase and pour new apron (concrete or asphalt) so that water is pitched away from the building. The issue is that currently water is pitched towards the door and water leaks into the supply room. Confirm with the COR and Facility Superintendent that there are no utilities under the slab.

5.14. Excavate from the building to the man gate at the eastern fence line, either near the mechanical room or install conduit through the building to the Eastern face and then excavate from there to the man gate at the eastern fence line. Lay two 1-inch conduit (conduit to be of material rated for buried in the ground) in the trench.

Provide pull lines in the conduit and stub up with a cap 12 inches at the man gate at the fence line.

5.15. Remove the current Vehicle Exhaust System. Any Unistrut and threaded rods not being repurposed will be removed. Remove all wiring and replace with new wiring that supports the three phase, three horsepower blower motors.

5.16. Provide new vehicle exhaust system (basis of design is Fume-A-Vent with MIL spec materials) that has five independent lines run from current window exhaust point via a fabricated manifold with five holes cut out. Provide an exterior exhaust hood to over the five exhaust ports. Try to reduce as many elbows as possible with straight line runs and angling to hose reels in the direction the fan motor will blow. Each of the five lines will have a spring actuated hose reel, with 30 feet (field verify length needed) of hose to reach from hose reel to the floor, with a stainless-steel nozzle with clamp, and a 3HP/3PH motor attached to the hose reel. The lines will be 8 inch in diameter or the recommended diameter by the manufacturer to achieve over 900 CFM at the nozzle. Wire new control panels at chest height in each work bay.

Breaker boxes are located in the mechanical room. Re-configure the breaker boxes as needed to support a three-phase system for the blower motors at each of the five work bays.

5.17. Conduct a test at each hose nozzle to validate the CFM rating. National Guard

Bureau Industrial Hygiene survey technician utilizes an ALNOR VELOMETER AVM410 anemometer. The instrument is positioned at multiple points across the face of the local exhaust opening (intake nozzle). The velocities are then recorded and averaged to provide a calculated velocity measurement by the anemometer.

The volume of exhausted air is calculated by multiplying the average face velocity by the area of the opening. This is a method approved by the National Guard Bureau Industrial Hygiene department. Other methods are acceptable if approved by the American Conference of Governmental Industrial Hygienists (ACGIH).

5.18. Contractor will replace any defective components or material in workmanship.

5.19. Contractor will replace any damage to equipment prior to acceptance to include in-transit delivery and damage during installation.

5.20. Contractor is responsible for maintaining cleanliness of the work area each day.

This includes but not limited to any debris created from drilling, removals, demolition, or installation of equipment.

5.21. All debris from delivery, unpacking, and installation will be disposed of by the

Contractor and disposed of offsite.

6.0 Applicable Publications: Publications applicable to this PWS are listed below:

Publication (Chapter/Page)

Date of Publication

Mandatory or Advisory

Website

Federal Acquisition Regulation https://www.acquisition.gov/?q=browsef ar

Defense Federal Acquisition Regulation Supplement http://www.acq.osd.mil/dpap/dars/dfars pgi/current/index.html or https://www.acquisition.gov/dfars Joint Travel Regulation (JTR) https://www.defensetravel.dod.mil/site/t ravelreg.cfm DoDM 1000.13-M-V1

DoD Identification (ID) Cards (Enclosure 2, paragraph 3.b)

01/23/2014 (Change 1:

07/28/2020) http://www.esd.whs.mil/Directives/issua nces/dodm

DoDM 5200.2 Procedures for the DoD Personnel Security Program (PSP)

04/03/2017 https://www.esd.whs.mil/Directives/issu ances/dodm/

DoDI 5200.46 DoD Investigative and Adjudicative Guidance for Issuing the Common Access Card (CAC)

09/09/14 (Change 1:

05/04/2018) https://www.esd.whs.mil/Directives/issu ances/dodi/

Homeland Security Presidential Directive (HSPD)-12 Policy for a Common Identification

Standard for Federal Employees and Contractors

08/27/2004 https://www.dhs.gov/homeland-security-presidential-directive-12

DoDI 5400.11 Department of Defense Privacy and Civil

Liberties Programs

01/29/2019 https://www.esd.whs.mil/Directives/issu ances/dodi/

DoD 5400.11-R Department of Defense Privacy Program

05/14/2007 https://www.esd.whs.mil/Directives/issu ances/dodm/

DoDD 8140.01 Cyberspace Workforce Management

10/05/2020 https://www.esd.whs.mil/Directives/issu ances/dodd/

Army Directive 2014-05 Policy and Implementation Procedures for Common Access Card Credentialing and

Installation Access for Uncleared Contractors

03/07/2014 https://armypubs.army.mil/ProductMap s/PubForm/ArmyDir.aspx

AR 530-1

Operations Security

09/26/2014 http://armypubs.army.mil/ProductMaps/ PubForm/AR.aspx

AR 525-13

Antiterrorism

12/09/2019 http://armypubs.army.mil/ProductMaps/ PubForm/AR.aspx

AR 381-12

Threat Awareness and Reporting Program

(TARP) (Section II, ¶ 2-4.b)

06/01/2016 http://armypubs.army.mil/ProductMaps/ PubForm/AR.aspx

6.1 Applicable Forms: Forms applicable to the PWS are listed below:

Form Date Website

DD 1172-2

Application for Identification Card/DEERS Enrollment

Mar 2017 http://www.dtic.mil/whs/directives/forms/index.htm

I-9 Employment Eligibility Verification

10/21/2019 https://www.uscis.gov/sites/default/files/files/form/i-9.pdf

DD 441

Department of Defense Security

Agreement

Feb 2020 http://www.dtic.mil/whs/directives/forms/dd/ddforms0001- 0499.htm

DD 250

Material Inspection and Receiving

Report

Aug 2000 https://www.esd.whs.mil/Directives/forms/dd0001_0499/

TECHNICAL EXHIBIT 1

Performance Requirements Summary (PRS)

This PRS includes performance objectives the Government will use to determine contractor performance and will compare contractor performance to the Acceptable Quality Level (AQL).

Performance Objective

Performance Standard Acceptable Quality Levels (AQL)

Surveillance Method / By Whom

5.2, 5.3, 5.7, 5.8, 5.9, 5.10, 5.11, 5.12

Remove and replace four exterior double doors and frame, provide new hardware.

99% removal; 100% Installation

1.4.3, 1.4.4

5.4, 5.5, 5.6, 5.7, 5.8, 5.9, 5.10, 5.11, 5.12

Remove and replace six exterior single doors and frame, provide new hardware. (one with magnetic lock compatible)

99% removal; 100% Installation

1.4.3, 1.4.4

5.13 Provide new apron in front

of supply room.

99% removal; 100% Installation

1.4.3, 1.4.4

5.14 Trench two 1 inch conduit

from building to man gate at fence line.

99% removal; 100% Installation

1.4.3, 1.4.4

5.15, 5.16 Remove and provide new vehicle exhaust system with five independent lines.

99% removal; 100% Installation

1.4.3, 1.4.4

5.17 New Vehicle Exhaust

System tests at 900+ CFM at nozzle (4.1.1)

> 900 CFM 1.4.3, 1.4.4

TECHNICAL EXHIBIT 2

Deliverables Schedule

PWS Reference / Deliverable Title

Frequency Number of Copies

Medium/Format Submit To

1.4.10 Identification

Media

Return within 14 days of employee’s departure from contract performance.

Original(s) Hard Copy Air Base Security Office

Provide verification of measurements and device count

Prior to ordering materials 1 Written or Email verification

COR

Provide shipment transmittal to COR

Upon receiving and verifying material send a copy to COR

1 Original or Copy of Original

COR

Provide a copy of Electrician NYS

License

Prior to execution of any electrical or data connections

1 Email a digital PDF or JPEG copy

COR

Provide Delivery Schedule

Prior to acceptance of delivered material

1 Email schedule COR

Provide Installation Schedule

Prior to installation 1 Email schedule COR

Provide Submittal Data Sheet for all

Material Used

Within 30 Days of Award 1 Email a digital PDF copy

COR

Provide CFM Test Results

Prior to Substantial Completion

1 Email a digital PDF copy

COR

INSTRUCTIONS TO OFFERORS

1. INSTRUCTIONS, CONDITIONS, AND NOTICES TO OFFERORS

You are invited to submit a quote in response to our Request for Quote (RFQ) W912PQ23Q0036, FMS Building 5 Improvements Syracuse, NY.

2. NOTICE OF SITE VISIT:

A site visit will be held on Thursday 17 August 2023 at 11:00 am EST at FMS Building 5 on Syracuse Enclave on the Hancock Field Air Base, 6900 Thompson Rd, Syracuse, NY 13211.

Due to security concerns, all offerors must register to attend the site visit. Email the following information for allattendees to andrew.e.emrich.civ@army.mil and Melissa.Santoro2.civ@army.mil

Firm Name Vehicle Type Telephone Number Visitor's Full Name(s)

This information must be provided NLT Tuesday 15 August 2023 at 3:00pm EST to secure a spot. The furnishing of the information above is voluntary; however, your failure to furnish all or part of the requested information may result in the Government's denial of your access to the site visit. This information will be provided to the Base Security Forces who will authorize your entrance to the site.

You will be required to present the following information upon arrival:

(1) Vehicle Registration,

(2) Valid Drivers License,

(3) Proof of Insurance for Vehicle,

(4) Safety Inspection and Car Rental agreement if applicable.

Any of the above information furnished by you is protected under the Privacy Act and shall not be released unless permitted by law and/or you have consented to such.

Information provided at this site visit shall not qualify the terms and conditions of the solicitation and specifications.

Terms of the solicitation and specifications remain unchanged unless the solicitation is amended in writing. If an amendment is issued, normal procedures relating to the acknowledgment and receipt of solicitation amendments shall apply.

3. FORMAL COMMUNICATION, OFFEROR EXPLANATIONS:

Submit all questions in the format shown below by email to the contracting office at the addresses below. Do NOT contact other personnel directly. Doing so will only delay your answer. All questions must come through the Contracting Office. Email questions to: andrew.e.emrich.civ@army.mil and Melissa.Santoro2.civ@army.mil Subject Line: Reference No. SOLICITATION W912PQ23Q0036, FMS Building 5 Improvements

INQUIRY FORMAT

Date of Inquiry:

From (Company Name):

Phone Number:

Inquiry: (Please clearly state your question) (If sent via an attachment word docs are preferred to facilitate posting of answers to the master Q&A document)

Any explanation desired by an offeror regarding the meaning or interpretation of the solicitation, SOW, etc. must be requested in writing and with sufficient time allowed for a reply to reach offerors before the submission of their quote.

All questions and requests for information (RFI) must be received NOT LATER THAN the FIFTH working day prior to the due date for quotes. OFFERORS ARE STRONGLY ENCOURAGED TO SUBMIT QUESTIONS

EARLY IN THIS PROCESS.

Any changes to the SOW, etc will be issued in the form of amendment. However, any answers that clarify or provide an interpretation will NOT be posted via amendment but rather as a response to the RFI via electronic means.

4. WAGE DETERMINATION:

Service Wage Rates applicable to this project are General Decision Number: 2015-4163 Last Revised Date Jun 30, 2023. Wage determination is incorporated at the end of this RFQ.

5. QUOTE PREPARATION EXPENSES AND PRE-CONTRACT COSTS:

This RFQ does not commit the Government to pay costs incurred in preparation and submission of quotes or for other costs incurred prior to award of a formal contract.

6. CLAUSES

Clauses and provisions from the Federal Acquisition Regulation (FAR) and supplements thereto are incorporated in this document by reference and in full text. Those incorporated by reference have the same force and effect as if they were given in full text.

7. DISPOSITION OFUNSUCCESSFUL QUOTES:

In compliance with FAR Subpart 4.8, the Government will retain one copy of all unsuccessful quotes.

8. OFFERORS QUALIFICATIONS:

To establish its responsibility, the apparent winning offeror may be requested by the Government prior to award, to submit a statement regarding its previous experience in performing comparable work, its business and technical organization, and plant available to be used in performing the work. This action may be requested to determine if the contractor is responsible.

ITEM NO SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

0001 1 Job Labor

FFP

Labor to complete all requirements listed in PWS section 5.

See incorporated PWS for more details on the requirement. Service Contract Act Wage Determination No.: 2015-4163 applies and is incorporated.

FOB: Destination

PURCHASE REQUEST NUMBER: 0011924781

PSC CD: J049

NET AMT

0002 1 Job Material

FFP

Material to complete all requirements listed in PWS section 5.

See incorporated PWS for more details on the requirement.

FOB: Destination

0003 1 Job Delivery

FFP

Delivery of all materials require to complete the requirements listed in PWS section 5.

See incorporated PWS for more details on the requirement.

FOB: Destination

INSPECTION AND ACCEPTANCE TERMS

Supplies/services will be inspected/accepted at:

CLIN INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY

0001 Destination Government Destination Government 0002 Destination Government Destination Government 0003 Destination Government Destination Government

DELIVERY INFORMATION

CLIN DELIVERY DATE QUANTITY SHIP TO ADDRESS DODAAC /

CAGE

0001 POP 21-AUG-2023 TO

20-AUG-2024

N/A JFHQ-NY, ATTN: MNFE

MAJ TRENTON ROESKE

6900 THOMPSON RD

SYRACUSE NY 13211

W56PPG

0002 POP 21-AUG-2023 TO

20-AUG-2024

N/A (SAME AS PREVIOUS LOCATION)

0003 POP 21-AUG-2023 TO

20-AUG-2024

N/A (SAME AS PREVIOUS LOCATION)

CLAUSES INCORPORATED BY REFERENCE

52.202-1 Definitions JUN 2020 52.203-3 Gratuities APR 1984 52.203-6 Alt I Restrictions On Subcontractor Sales To The Government

(JUN 2020) -- Alternate I

NOV 2021

52.203-12 Limitation On Payments To Influence Certain Federal Transactions

JUN 2020

52.203-19 Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements

JAN 2017

52.204-4 Printed or Copied Double-Sided on Postconsumer Fiber Content Paper

MAY 2011

52.204-7 System for Award Management OCT 2018 52.204-9 Personal Identity Verification of Contractor Personnel JAN 2011 52.204-10 Reporting Executive Compensation and First-Tier

Subcontract Awards

JUN 2020

52.204-13 System for Award Management Maintenance OCT 2018 52.204-16 Commercial and Government Entity Code Reporting AUG 2020 52.204-18 Commercial and Government Entity Code Maintenance AUG 2020 52.204-23 Prohibition on Contracting for Hardware, Software, and

Services Developed or Provided by Kaspersky Lab and Other Covered Entities

NOV 2021

52.204-25 Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment

NOV 2021

52.204-27 Prohibition on a ByteDance Covered Application JUN 2023 52.209-10 Prohibition on Contracting With Inverted Domestic

Corporations

NOV 2015

52.212-4 Contract Terms and Conditions--Commercial Products and Commercial Services

DEC 2022

52.219-8 (Dev) Utilization of Small Business Concerns (Deviation 2023- O0002)

DEC 2022

52.219-27 Notice of Service-Disabled Veteran-Owned Small Business Set-Aside

OCT 2022

52.222-3 Convict Labor JUN 2003 52.222-21 Prohibition Of Segregated Facilities APR 2015 52.222-26 Equal Opportunity SEP 2016 52.222-37 Employment Reports on Veterans JUN 2020 52.222-40 Notification of Employee Rights Under the National Labor

Relations Act

DEC 2010

52.222-41 Service Contract Labor Standards AUG 2018 52.222-43 Fair Labor Standards Act And Service Contract Labor

Standards - Price Adjustment (Multiple Year And Option Contracts)

AUG 2018

52.222-50 Combating Trafficking in Persons NOV 2021 52.222-54 Employment Eligibility Verification MAY 2022

52.222-55 Minimum Wages for Contractor Workers Under Executive Order 14026

JAN 2022

52.223-5 Pollution Prevention and Right-to-Know Information MAY 2011 52.223-6 Drug-Free Workplace MAY 2001 52.223-18 Encouraging Contractor Policies To Ban Text Messaging

While Driving

JUN 2020

52.225-13 Restrictions on Certain Foreign Purchases FEB 2021 52.229-3 Federal, State And Local Taxes FEB 2013 52.229-11 Tax on Certain Foreign Procurements--Notice and

Representation

JUN 2020

52.229-12 Tax on Certain Foreign Procurements FEB 2021 52.232-17 Interest MAY 2014 52.232-33 Payment by Electronic Funds Transfer--System for Award

Management

OCT 2018

52.233-1 Alt I Disputes (May 2014) - Alternate I DEC 1991 52.233-3 Protest After Award AUG 1996 52.233-4 Applicable Law for Breach of Contract Claim OCT 2004 52.237-2 Protection Of Government Buildings, Equipment, And

Vegetation

APR 1984

52.237-3 Continuity Of Services JAN 1991 52.242-13 Bankruptcy JUL 1995 52.242-17 Government Delay Of Work APR 1984 52.246-4 Inspection Of Services--Fixed Price AUG 1996 52.247-34 F.O.B. Destination NOV 1991 52.253-1 Computer Generated Forms JAN 1991 252.203-7002 Requirement to Inform Employees of Whistleblower Rights DEC 2022 252.204-7000 Disclosure Of Information OCT 2016 252.204-7003 Control Of Government Personnel Work Product APR 1992 252.204-7008 Compliance With Safeguarding Covered Defense Information

Controls

OCT 2016

252.204-7015 Notice of Authorized Disclosure of Information for Litigation Support

JAN 2023

252.204-7016 Covered Defense Telecommunications Equipment or Services -- Representation

DEC 2019

252.204-7017 Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services -- Representation

MAY 2021

252.204-7018 Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services

JAN 2023

252.204-7024 Notice on the Use of the Supplier Performance Risk System MAR 2023 252.209-7004 Subcontracting With Firms That Are Owned or Controlled By

The Government of a Country that is a State Sponsor of Terrorism

MAY 2019

252.215-7008 Only One Offer DEC 2022 252.225-7001 Buy American And Balance Of Payments Program--Basic JAN 2023 252.225-7002 Qualifying Country Sources As Subcontractors MAR 2022 252.225-7012 Preference For Certain Domestic Commodities APR 2022 252.225-7052 Restriction on the Acquisition of Certain Magnets, Tantalum, and Tungsten.

JAN 2023

252.225-7055 Representation Regarding Business Operations with the Maduro Regime

MAY 2022

252.225-7056 Prohibition Regarding Business Operations with the Maduro Regime

JAN 2023

252.225-7059 Prohibition on Certain Procurements from the Xinjiang Uyghur Autonomous Region - Representation

JUN 2023

252.225-7060 Prohibition on Certain Procurements from the Xinjiang Uyghur Autonomous Region

JUN 2023

252.229-7014 Full Exemption from Two-Percent Excise Tax on Certain Foreign Procurements

OCT 2022

252.232-7003 Electronic Submission of Payment Requests and Receiving Reports

DEC 2018

252.232-7010 Levies on Contract Payments DEC 2006 252.239-7098 (Dev) Prohibition on Contracting to Maintain or Establish a

Computer Network Unless Such Network is Designed to Block Access to Certain Websites - Representation.

(Deviation 2021-O0003)

APR 2021

252.243-7001 Pricing Of Contract Modifications DEC 1991 252.243-7002 Requests for Equitable Adjustment DEC 2022 252.244-7000 Subcontracts for Commercial Products or Commercial

Services

JAN 2023

CLAUSES INCORPORATED BY FULL TEXT

52.203-17 CONTRACTOR EMPLOYEE WHISTLEBLOWER RIGHTS AND REQUIREMENT TO INFORM

EMPLOYEES OF WHISTLEBLOWER RIGHTS (JUN 2020)

(a) This contract and employees working on this contract will be subject to the whistleblower rights and remedies in the pilot program on Contractor employee whistleblower protections established at 41 U.S.C. 4712 by section 828 of the National Defense Authorization Act for Fiscal Year 2013 (Pub. L. 112-239) and Federal Acquisition Regulation

(FAR) 3.908.

(b) The Contractor shall inform its employees in writing, in the predominant language of the workforce, of employee whistleblower rights and protections under 41 U.S.C. 4712, as described in FAR 3.908.

(c) The Contractor shall insert the substance of this clause, including this paragraph (c), in all subcontracts over the simplified acquisition threshold, as defined in FAR 2.101 on the date of subcontract award.

(End of clause)

52.203-18 PROHIBITION ON CONTRACTING WITH ENTITIES THAT REQUIRE CERTAIN INTERNAL

CONFIDENTIALITY AGREEMENTS OR STATEMENTS--REPRESENTATION (JAN 2017)

(a) Definition. As used in this provision-- Internal confidentiality agreement or statement, subcontract, and subcontractor, are defined in the clause at 52.203- 19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements.

(b) In accordance with section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L. 113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions), Government agencies are not permitted to use funds appropriated (or otherwise made available) for contracts with an entity that requires employees or subcontractors of such entity seeking to report waste, fraud, or abuse to sign internal confidentiality agreements or statements prohibiting or otherwise restricting such employees or subcontractors from lawfully reporting such waste, fraud, or abuse to a designated investigative or law enforcement representative of a Federal department or agency authorized to receive such information.

(c) The prohibition in paragraph (b) of this provision does not contravene requirements applicable to Standard Form 312, (Classified Information Nondisclosure Agreement), Form 4414 (Sensitive Compartmented Information

Nondisclosure Agreement), or any other form issued by a Federal department or agency governing the nondisclosure of classified information.

(d) Representation. By submission of its offer, the Offeror represents that it will not require its employees or subcontractors to sign or comply with internal confidentiality agreements or statements prohibiting or otherwise restricting such employees or subcontractors from lawfully reporting waste, fraud, or abuse related to the performance of a Government contract to a designated investigative or law enforcement representative of a Federal department or agency authorized to receive such information (e.g., agency Office of the Inspector General).

(End of provision)

52.204-19 INCORPORATION BY REFERENCE OF REPRESENTATIONS AND CERTIFICATIONS (DEC

2014)

The Contractor's representations and certifications, including those completed electronically via the System for Award Management (SAM), are incorporated by reference into the contract.

52.204-20 Predecessor of Offeror (AUG 2020)

(a) Definitions. As used in this provision--

Commercial and Government Entity (CAGE) code means--

(1) An identifier assigned to entities located in the United States or its outlying areas by the Defense Logistics Agency (DLA) Commercial and Government Entity (CAGE) Branch to identify a commercial or government entity by unique location; or

(2) An identifier assigned by a member of the North Atlantic Treaty Organization (NATO) or by the NATO Support and Procurement Agency (NSPA) to entities located outside the United States and its outlying areas that the DLA Commercial and Government Entity (CAGE) Branch records and maintains in the CAGE master file. This type of code is known as a NATO CAGE (NCAGE) code.

Predecessor means an entity that is replaced by a successor and includes any predecessors of the predecessor.

Successor means an entity that has replaced a predecessor by acquiring the assets and carrying out the affairs of the predecessor under a new name (often through acquisition or merger). The term “successor” does not include new offices/divisions of the same company or a company that only changes its name. The extent of the responsibility of the successor for the liabilities of the predecessor may vary, depending on State law and specific circumstances.

(b) The Offeror represents that it [____] is or [____] is not a successor to a predecessor that held a Federal contract or grant within the last three years.

(c) If the Offeror has indicated “is” in paragraph (b) of this provision, enter the following information for all predecessors that held a Federal contract or grant within the last three years (if more than one predecessor, list in reverse chronological order):

Predecessor CAGE code: ____ (or mark “Unknown”).

Predecessor legal name: ____.

(Do not use a “doing business as” name).

52.204-21 BASIC SAFEGUARDING OF COVERED CONTRACTOR INFORMATION SYSTEMS (NOV 2021)

(a) Definitions. As used in this clause--

Covered contractor information system means an information system that is owned or operated by a contractor that processes, stores, or transmits Federal contract information.

Federal contract information means information, not intended for public release, that is provided by or generated for the Government under a contract to develop or deliver a product or service to the Government, but not including information provided by the Government to the public (such as on public websites) or simple transactional information, such as necessary to process payments.

Information means any communication or representation of knowledge such as facts, data, or opinions, in any medium or form, including textual, numerical, graphic, cartographic, narrative, or audiovisual (Committee on National Security Systems Instruction (CNSSI) 4009).

Information system means a discrete set of information resources organized for the collection, processing, maintenance, use, sharing, dissemination, or disposition of information (44 U.S.C. 3502).

Safeguarding means measures or controls that are prescribed to protect information systems.

(b) Safeguarding requirements and…