Specifications_Volume_2_-_BTC4_Phase_2_AMD2.pdf

Fort Jackson, South Carolina

Solicitation Number

W912HP-19-R-2001

BCT4, Phase 2 Volume 2 of 4: Specification Divisions 06 - 22

PN 76218

July 2019

U.S. ARMY ENGINEER DISTRICT, SAVANNAH

CORPS OF ENGINEERS

100 WEST OGLETHORPE AVENUE

SAVANNAH, GEORGIA 31401-3640

US Army Corps of Engineers

BCT 4 Phase 2 JA76218 Ft. Jackson, SC

PROJECT TABLE OF CONTENTS

DIVISION 01 - GENERAL REQUIREMENTS

01 11 00 SUMMARY OF WORK

01 30 00 ADMINISTRATIVE REQUIREMENTS

01 32 01 PROJECT SCHEDULE

01 33 00 SUBMITTAL PROCEDURES

01 33 29 SUSTAINABILITY REPORTING

01 35 26 GOVERNMENTAL SAFETY REQUIREMENTS

01 42 00 SOURCES FOR REFERENCE PUBLICATIONS

01 45 00 QUALITY CONTROL

01 45 00.15 RESIDENT MANAGEMENT SYSTEM CONTRACTOR MODE (RMS CM)

01 45 35 SPECIAL INSPECTIONS

01 50 00 TEMPORARY CONSTRUCTION FACILITIES AND CONTROLS

01 57 19 TEMPORARY ENVIRONMENTAL CONTROLS

01 57 19.37 INDOOR AIR QUALITY (IAQ) MANAGEMENT

01 74 19.37 CONSTRUCTION AND DEMOLITION WASTE MANAGEMENT

01 78 00 CLOSEOUT SUBMITTALS

01 78 23 OPERATION AND MAINTENANCE DATA

01 91 00.15 TOTAL BUILDING COMMISSIONING

DIVISION 03 - CONCRETE

03 11 13 STRUCTURAL CAST-IN-PLACE CONCRETE FORMING

03 15 00 CONCRETE ACCESSORIES

03 20 00 CONCRETE REINFORCING

03 30 00 CAST-IN-PLACE CONCRETE

03 35 00 CONCRETE FINISHING

03 39 00 CONCRETE CURING

DIVISION 04 - MASONRY

04 20 00 MASONRY

DIVISION 05 - METALS

05 05 23.16 STRUCTURAL WELDING

05 12 00 STRUCTURAL STEEL

05 21 00 STEEL JOIST FRAMING

05 30 00 STEEL DECKS

05 40 00 COLD-FORMED METAL FRAMING

05 50 13 MISCELLANEOUS METAL FABRICATIONS

05 51 00 METAL STAIRS

05 51 33 METAL LADDERS

05 52 00 METAL RAILINGS

DIVISION 06 - WOOD, PLASTICS, AND COMPOSITES

06 10 00 ROUGH CARPENTRY

06 20 00 FINISH CARPENTRY

06 41 16 LAMINATE CLAD ARCHITECTURAL CASEWORK

06 61 16 SOLID POLYMER (SOLID SURFACING) FABRICATIONS

DIVISION 07 - THERMAL AND MOISTURE PROTECTION

07 05 23 PRESSURE TESTING AN AIR BARRIER SYSTEM FOR AIR TIGHTNESS

07 21 13 BOARD AND BLOCK INSULATION

07 21 16 MINERAL FIBER BLANKET INSULATION

PROJECT TABLE OF CONTENTS Page 1 (Revised by Amendment 0002)

07 22 00 ROOF AND DECK INSULATION

07 27 10 BUILDING AIR BARRIER SYSTEM

07 41 00 METAL SOFFIT PANELS

07 41 13 METAL ROOF PANELS

07 42 13 METAL WALL PANELS

07 53 23 ETHYLENE-PROPYLENE-DIENE-MONOMER ROOFING

07 60 00 FLASHING AND SHEET METAL

07 81 00 *2 SPRAY-APPLIED FIREPROOFING

07 84 00 FIRESTOPPING

07 92 00 JOINT SEALANTS

DIVISION 08 - OPENINGS

08 11 13 STEEL DOORS AND FRAMES

08 11 16 ALUMINUM DOORS AND FRAMES

08 14 00 WOOD DOORS

08 34 59 VAULT DOORS AND DAY GATES

08 34 73 SOUND CONTROL DOOR ASSEMBLIES

08 44 00 CURTAIN WALL AND GLAZED ASSEMBLIES

08 51 13 ALUMINUM WINDOWS

08 71 00 DOOR HARDWARE

08 81 00 GLAZING

08 91 00 METAL WALL LOUVERS

DIVISION 09 - FINISHES

09 06 00 SCHEDULES FOR FINISHES

09 22 00 SUPPORTS FOR PLASTER AND GYPSUM BOARD

09 29 00 GYPSUM BOARD

09 30 10 CERAMIC, QUARRY, AND GLASS TILING

09 51 00 ACOUSTICAL CEILINGS

09 65 00 RESILIENT FLOORING

09 67 23.13 STANDARD RESINOUS FLOORING

09 90 00 PAINTS AND COATINGS

DIVISION 10 - SPECIALTIES

10 09 00 MISCELLANEOUS ITEMS

10 10 00 VISUAL COMMUNICATIONS SPECIALTIES

10 14 00.20 INTERIOR SIGNAGE

10 21 13 TOILET COMPARTMENTS

10 26 00 WALL AND DOOR PROTECTION

10 28 13 TOILET ACCESSORIES

DIVISION 11 - EQUIPMENT

11 06 40.13 FOODSERVICE EQUIPMENT SCHEDULE

11 81 29 *2 FACILITY FALL PROTECTION

DIVISION 12 - FURNISHINGS

12 21 00 *2 DELETED WINDOW BLINDS

12 24 13 ROLLER WINDOW SHADES

12 24 13.11 ROLLER WINDOW SHADES

12 48 13 ENTRANCE FLOOR MATS AND FRAMES

12 93 00 SITE FURNISHINGS

DIVISION 13 - SPECIAL CONSTRUCTION

PROJECT TABLE OF CONTENTS Page 2 (Revised by Amendment 0002)

13 34 19 METAL BUILDING SYSTEMS (COVERED TRAINING CANOPY)

13 48 00 SEISMIC PROTECTION FOR MISCELLANEOUS EQUIPMENT

13 48 00.22 SEISMIC PROTECTION FOR MECHANICAL EQUIPMENT

DIVISION 21 - FIRE SUPPRESSION

21 13 13 WET PIPE SPRINKLER SYSTEM, FIRE PROTECTION

DIVISION 22 - PLUMBING

22 00 00 PLUMBING, GENERAL PURPOSE

DIVISION 23 - HEATING, VENTILATING, AND AIR CONDITIONING (HVAC)

23 00 00 AIR SUPPLY, DISTRIBUTION, VENTILATION, AND EXHAUST SYSTEMS

23 05 48 VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND

EQUIPMENT

23 05 93 TESTING, ADJUSTING, AND BALANCING FOR HVAC

23 07 00 THERMAL INSULATION FOR MECHANICAL SYSTEMS

23 09 00 INSTRUMENTATION AND CONTROL FOR HVAC

23 09 13 INSTRUMENTATION AND CONTROL DEVICES FOR HVAC

23 09 23.01 LONWORKS DIRECT DIGITAL CONTROL FOR HVAC AND OTHER

BUILDING CONTROL SYSTEMS

23 11 25 FACILITY GAS PIPING

23 23 00 REFRIGERANT PIPING

23 25 00 CHEMICAL TREATMENT OF WATER FOR MECHANICAL SYSTEMS

23 52 00 HEATING BOILERS

23 57 10 FORCED HOT WATER HEATING SYSTEMS USING WATER HEAT

EXCHANGERS

23 64 10 WATER CHILLERS, VAPOR COMPRESSION TYPE

23 64 26 CHILLED, CHILLED-HOT, AND CONDENSER WATER PIPING SYSTEMS

23 82 02 UNITARY HEATING AND COOLING EQUIPMENT

DIVISION 25 - INTEGRATED AUTOMATION

25 05 11 CYBERSECURITY FOR FACILITY-RELATED CONTROL SYSTEMS (HVAC)

25 05 12 CYBERSECURITY FOR FACILITY-RELATED CONTROL SYSTEMS (DMS)

25 05 13 CYBERSECURITY FOR FACILITY-RELATED CONTROL SYSTEMS

(FA/MNS)

25 08 10 UTILITY MONITORING AND CONTROL SYSTEM TESTING

25 10 10 UTILITY MONITORING AND CONTROL SYSTEM (UMCS) FRONT END

AND INTEGRATION

DIVISION 26 - ELECTRICAL

26 00 00 BASIC ELECTRICAL MATERIALS AND METHODS

26 05 48 SEISMIC PROTECTION FOR ELECTRICAL EQUIPMENT

26 20 00 INTERIOR DISTRIBUTION SYSTEM

26 23 00 SWITCHBOARDS

26 28 01 COORDINATED POWER SYSTEM PROTECTION

26 29 23 VARIABLE FREQUENCY DRIVE SYSTEMS UNDER 600 VOLTS

26 41 00 LIGHTNING PROTECTION SYSTEM

26 51 00 INTERIOR LIGHTING

26 56 00 EXTERIOR LIGHTING

DIVISION 27 - COMMUNICATIONS

27 05 14 CABLE TELEVISION PREMISES DISTRIBUTION SYSTEM

27 10 00 BUILDING TELECOMMUNICATIONS CABLING SYSTEM

PROJECT TABLE OF CONTENTS Page 3 (Revised by Amendment 0002)

DIVISION 28 - ELECTRONIC SAFETY AND SECURITY

28 16 01 SMALL INTRUSION DETECTION SYSTEM

28 20 01 DOOR MONITORING SYSTEM

28 31 76 INTERIOR FIRE ALARM AND MASS NOTIFICATION SYSTEMS

DIVISION 31 - EARTHWORK

31 00 00 EARTHWORK

31 05 19 GEOTEXTILE

31 11 00 CLEARING AND GRUBBING

31 31 16.13 CHEMICAL TERMITE CONTROL

31 32 11 SOIL SURFACE EROSION CONTROL

DIVISION 32 - EXTERIOR IMPROVEMENTS

32 01 19 FIELD MOLDED SEALANTS FOR SEALING JOINTS IN RIGID

PAVEMENTS

32 05 33 LANDSCAPE ESTABLISHMENT

32 11 16 BASE COURSE FOR RIGID PAVING

32 11 23 AGGREGATE AND/OR GRADED-CRUSHED AGGREGATE BASE COURSE

32 12 10 BITUMINOUS TACK AND PRIME COATS

32 12 16 HOT-MIX ASPHALT (HMA) FOR ROADS

32 13 13.06 PORTLAND CEMENT CONCRETE PAVEMENT FOR ROADS AND SITE

FACILITIES

32 16 19 CONCRETE CURBS, GUTTERS AND SIDEWALKS

32 17 23 PAVEMENT MARKINGS

32 18 23.39 *2 DELETED SYNTHETIC RUNNING TRACK SURFACING

32 31 13 CHAIN LINK FENCES AND GATES

32 32 23 *2 DELETED SEGMENTAL CONCRETE BLOCK RETAINING WALL

32 92 19 SEEDING

32 92 23 SODDING

32 93 00 EXTERIOR PLANTS

DIVISION 33 - UTILITIES

33 40 00 STORM DRAINAGE UTILITIES

33 46 16 SUBDRAINAGE PIPING

33 51 15 NATURAL-GAS DISTRIBUTION

33 61 13.13 PREFABRICATED UNDERGROUND HYDRONIC ENERGY DISTRIBUTION

33 71 02 UNDERGROUND ELECTRICAL DISTRIBUTION

33 82 00 TELECOMMUNICATIONS OUTSIDE PLANT (OSP)

-- End of Project Table of Contents --

PROJECT TABLE OF CONTENTS Page 4 (Revised by Amendment 0002)

Ft . Jackson, SC

SECTI ON TABLE OF CONTENTS

DI VI SI ON 06 - WOOD, PLASTI CS, AND COMPOSI TES

SECTI ON 06 10 00

ROUGH CARPENTRY

02/12

PART 1 GENERAL

1. 1 REFERENCES

1. 2 SUBMI TTALS

1. 3 DELI VERY AND STORAGE

1. 4 GRADI NG AND MARKI NG

1. 4. 1 Lumber

1. 4. 2 Pl ywood

1. 4. 3 Pr eser vat i ve- Tr eat ed Lumber and Pl ywood

1. 5 SI ZES AND SURFACI NG

1. 6 MOI STURE CONTENT

1. 7 PRESERVATI VE TREATMENT

1. 8 Cer t i f i cat es of Gr ade

1. 9 SUSTAI NABLE DESI GN REQUI REMENTS

PART 2 PRODUCTS

2. 1 LUMBER

2. 2 OTHER MATERI ALS

2. 2. 1 Mi scel l aneous Wood Member s

2. 2. 1. 1 Nonst r ess Gr aded Member s

2. 2. 1. 2 Si l l Pl at es

2. 2. 1. 3 Bl ocki ng

2. 2. 2 Adhesi ves

2. 3 ROUGH HARDWARE

2. 3. 1 Bol t s, Nut s, St uds, and Ri vet s

2. 3. 2 Anchor Bol t s

2. 3. 3 Expansi on Shi el ds

2. 3. 4 Lag Scr ews and Lag Bol t s

2. 3. 5 Wood Scr ews

2. 3. 6 Nai l s

2. 3. 7 Wi r e Nai l s

2. 3. 8 Cl i p Angl es

2. 3. 9 Met al Fr ami ng Anchor s

2. 3. 10 Panel Edge Cl i ps

PART 3 EXECUTI ON

3. 1 I NSTALLATI ON

3. 1. 1 Si l l s

3. 1. 2 Anchor s i n Masonr y

3. 1. 3 Anchor s i n Concr et e

3. 2 MI SCELLANEOUS

3. 2. 1 Wood Roof Nai l er s, Edge St r i ps, Cr i cket s, Cur bs, and Cant s

3. 2. 1. 1 Roof Edge St r i ps and Nai l er s

3. 2. 1. 2 Cr i cket s, Cant s, and Cur bs

SECTI ON 06 10 00 Page 1

3. 2. 2 Wood Bl ocki ng

3. 2. 3 Wood Gr ounds

3. 2. 4 Wood Fur r i ng

3. 2. 5 Tempor ar y Cl osur es

3. 2. 6 Tempor ar y Cent er i ng, Br aci ng, and Shor i ng

3. 2. 7 Si l l Pl at es

- - End of Sect i on Tabl e of Cont ent s - -

SECTI ON 06 10 00 Page 2

SECTI ON 06 10 00

ROUGH CARPENTRY

02/12

PART 1 GENERAL

1. 1 REFERENCES

The publ i cat i ons l i s t ed bel ow f or m a par t of t hi s speci f i cat i on t o t he ext ent r ef er enced. The publ i cat i ons ar e r ef er r ed t o wi t hi n t he t ext by t he basi c desi gnat i on onl y.

AMERI CAN LUMBER STANDARDS COMMI TTEE ( ALSC)

ALSC PS 20 ( 2015) Amer i can Sof t wood Lumber St andar d

AMERI CAN WOOD COUNCI L ( AWC)

AWC NDS ( 2015) Nat i onal Desi gn Speci f i cat i on ( NDS) f or Wood Const r uct i on

AWC WFCM ( 2012) Wood Fr ame Const r uct i on Manual f or One- and Two- Fami l y Dwel l i ngs

AMERI CAN WOOD PROTECTI ON ASSOCI ATI ON ( AWPA)

AWPA M2 ( 2016) St andar d f or t he I nspect i on of Pr eser vat i ve Tr eat ed Wood Pr oduct s f or I ndust r i al Use

AWPA M6 ( 2013) Br ands Used on Pr eser vat i ve Tr eat ed Materials

APA - THE ENGI NEERED WOOD ASSOCI ATI ON ( APA)

APA L870 ( 2010) Vol unt ar y Pr oduct St andar d, PS 1- 09, St r uct ur al Pl ywood

ASME I NTERNATI ONAL ( ASME)

ASME B18. 2. 1 ( 2012; Er r at a 2013) Squar e and Hex Bol t s and Scr ews ( I nch Ser i es)

ASME B18. 2. 2 ( 2015) Nut s f or Gener al Appl i cat i ons:

Machi ne Scr ew Nut s, Hex, Squar e, Hex Fl ange, and Coupl i ng Nut s ( I nch Ser i es)

ASME B18. 5. 2. 1M ( 2006; R 2011) Met r i c Round Head Shor t Squar e Neck Bol t s

ASME B18. 5. 2. 2M ( 1982; R 2010) Met r i c Round Head Squar e Neck Bol t s

ASME B18. 6. 1 ( 2016) Wood Scr ews ( I nch Ser i es)

SECTI ON 06 10 00 Page 3

ASTM I NTERNATI ONAL ( ASTM)

ASTM A153/ A153M ( 2016) St andar d Speci f i cat i on f or Zi nc Coat i ng ( Hot - Di p) on I r on and St eel Hardware

ASTM A307 ( 2014; E 2017) St andar d Speci f i cat i on f or Car bon St eel Bol t s, St uds, and Thr eaded Rod 60 000 PSI Tensi l e St r engt h

ASTM A653/ A653M ( 2018) St andar d Speci f i cat i on f or St eel Sheet , Zi nc- Coat ed ( Gal vani zed) or Zi nc- I r on Al l oy- Coat ed ( Gal vanneal ed) by t he Hot - Di p Pr ocess

ASTM F1667 ( 2018a) St andar d Speci f i cat i on f or Dr i ven Fast ener s: Nai l s, Spi kes, and St apl es

ASTM F547 ( 2017) St andar d Ter mi nol ogy of Nai l s f or Use wi t h Wood and Wood- Base Mat er i al s

FM GLOBAL ( FM)

FM 4435 ( 2013) Roof Per i met er Fl ashi ng

I NTERNATI ONAL CODE COUNCI L ( I CC)

I CC I BC ( 2018) I nt er nat i onal Bui l di ng Code

NATI ONAL HARDWOOD LUMBER ASSOCI ATI ON ( NHLA)

NHLA Rul es ( 2015) Rul es f or t he Measur ement & I nspect i on of Har dwood & Cypr ess

NORTHEASTERN LUMBER MANUFACTURERS ASSOCI ATI ON ( NELMA)

NELMA Gr adi ng Rul es ( 2013) St andar d Gr adi ng Rul es f or Nor t heast er n Lumber

REDWOOD I NSPECTI ON SERVI CE ( RI S) OF THE CALI FORNI A REDWOOD

ASSOCI ATI ON ( CRA)

RI S Gr ade Use ( 1998) Redwood Lumber Gr ades and Uses

SOUTHERN CYPRESS MANUFACTURERS ASSOCI ATI ON ( SCMA)

SCMA Spec ( 1986; Suppl e. No. 1, Aug 1993) St andar d Speci f i cat i ons f or Gr ades of Sout her n Cypress

SOUTHERN PI NE I NSPECTI ON BUREAU ( SPI B)

SPI B 1003 ( 2014) St andar d Gr adi ng Rul es f or Sout her n Pi ne Lumber

U. S. DEPARTMENT OF COMMERCE ( DOC)

DOC/ NI ST PS56 ( 1973) St r uct ur al Gl ued Lami nat ed Ti mber

SECTI ON 06 10 00 Page 4

U. S. GENERAL SERVI CES ADMI NI STRATI ON ( GSA)

CI D A- A- 1923 ( Rev A; Not i ce 3) Shi el d, Expansi on ( Lag, Machi ne and Ext er nal l y Thr eaded Wedge Bol t Anchors)

CI D A- A- 1924 ( Rev A; Not i ce 3) Shi el d, Expansi on ( Sel f Dr i l l i ng Tubul ar Expansi on Shel l Bol t Anchors

CI D A- A- 1925 ( Rev A; Not i ce 3) Shi el d Expansi on ( Nai l Anchors)

WEST COAST LUMBER I NSPECTI ON BUREAU ( WCLI B)

WCLI B 17 ( 2015) St andar d Gr adi ng Rul es

WESTERN WOOD PRODUCTS ASSOCI ATI ON ( WWPA)

WWPA G- 5 ( 2017) West er n Lumber Gr adi ng Rul es

1. 2 SUBMITTALS

Gover nment appr oval i s r equi r ed f or submi t t al s wi t h a " G" desi gnat i on;

submi t t al s not havi ng a " G" desi gnat i on ar e f or i nf or mat i on onl y. When used, a desi gnat i on f ol l owi ng t he " G" desi gnat i on i dent i f i es t he of f i ce t hat wi l l r evi ew t he submi t t al f or t he Gover nment . Submi t t he f ol l owi ng i n accor dance wi t h Sect i on 01 33 00 SUBMI TTAL PROCEDURES:

SD- 02 Shop Dr awi ngs

Nai l i ng St r i ps; G, RO

SD- 03 Pr oduct Dat a

LEED dat a f or r ecycl ed cont ent , r egi onal mat er i al s, cer t i f i ed wood, l ow- emi t t i ng mat er i al s.

SD- 06 Test Repor t s

Preservative-treated l umber and pl ywood

SD- 07 Cer t i f i cat es

Cer t i f i cat es of gr ade Pr eser vat i ve t r eat ment

1. 3 DELI VERY AND STORAGE

Del i ver mat er i al s t o t he s i t e i n an undamaged condi t i on. St or e, pr ot ect , handl e, and i nst al l pr ef abr i cat ed st r uct ur al el ement s i n accor dance wi t h manuf act ur er ' s i nst r uct i ons and as speci f i ed. St or e mat er i al s of f t he gr ound t o pr ovi de pr oper vent i l at i on, wi t h dr ai nage t o avoi d st andi ng wat er , and pr ot ect i on agai nst gr ound moi st ur e and dampness. St or e mat er i al s wi t h a moi st ur e bar r i er at bot h t he gr ound l evel and as a cover f or mi ng a wel l vent i l at ed encl osur e. St or e wood I - beams and gl ue- l ami nat ed beams and j oi st s on edge. Adher e t o r equi r ement s f or st acki ng, l i f t i ng, br aci ng, cut t i ng, not chi ng, and speci al f ast eni ng r equi r ement s. Remove def ect i ve and damaged mat er i al s and pr ovi de new mat er i al s. St or e separ at ed

SECTI ON 06 10 00 Page 5 r eusabl e wood wast e conveni ent t o cut t i ng st at i on and ar ea of wor k.

1. 4 GRADI NG AND MARKI NG

1. 4. 1 Lumber

Mar k each pi ece of f r ami ng and boar d l umber or each bundl e of smal l pi eces of l umber wi t h t he gr ade mar k of a r ecogni zed associ at i on or i ndependent i nspect i on agency. Such associ at i on or agency shal l be cer t i f i ed by t he Boar d of Revi ew, Amer i can Lumber St andar ds Commi t t ee, t o gr ade t he speci es used. Sur f aces t hat ar e t o be exposed t o v i ew shal l not bear gr ademar ks, st amps, or any t ype of i dent i f y i ng mar k. Hammer mar ki ng wi l l be per mi t t ed on t i mber s when al l sur f aces wi l l be exposed t o v i ew.

1. 4. 2 Plywood

Mar k each sheet wi t h t he mar k of a r ecogni zed associ at i on or i ndependent i nspect i on agency t hat mai nt ai ns cont i nui ng cont r ol over t he qual i t y of t he pl ywood. The mar k shal l i dent i f y t he pl ywood by speci es gr oup or span r at i ng, exposur e dur abi l i t y c l assi f i cat i on, gr ade, and compl i ance wi t h APA L870. Sur f aces t hat ar e t o be exposed t o v i ew shal l not bear gr ademar ks or ot her t ypes of i dent i f y i ng mar ks.

1. 4. 3 Preservative-Treated Lumber and Pl ywood

The Cont r act or shal l be r esponsi bl e f or t he qual i t y of t r eat ed wood pr oduct s. Each t r eat ed pi ece shal l be i nspect ed i n accor dance wi t h AWPA M2 and per manent l y mar ked or br anded, by t he pr oducer , i n accor dance wi t h AWPA M6. The Cont r act or shal l pr ovi de Cont r act i ng Of f i cer ' s Repr esent at i ve ( COR) wi t h t he i nspect i on r epor t of an appr oved i ndependent i nspect i on agency t hat of f er ed pr oduct s compl y wi t h appl i cabl e AWPA St andar ds. The appr opr i at e Qual i t y Mar k on each pi ece wi l l be accept ed, i n l i eu of i nspect i on r epor t s, as evi dence of compl i ance wi t h appl i cabl e AWPA t r eat ment st andar ds.

1. 5 SI ZES AND SURFACI NG

ALSC PS 20 f or dr essed si zes of yar d and st r uct ur al l umber . Lumber shal l be sur f aced f our s i des. Si ze r ef er ences, unl ess ot her wi se speci f i ed, ar e nomi nal s i zes, and act ual s i zes shal l be wi t hi n manuf act ur i ng t ol er ances al l owed by t he st andar d under whi ch t he pr oduct i s pr oduced. Ot her measur ement s ar e I P or SI st andar d.

1. 6 MOI STURE CONTENT

Ai r - dr y or k i l n- dr y l umber . Ki l n- dr y t r eat ed l umber af t er t r eat ment .

Maxi mum moi st ur e cont ent of wood pr oduct s shal l be as f ol l ows at t he t i me of del i ver y t o t he j ob s i t e:

a. Fr ami ng l umber and boar d, 19 per cent maxi mum

b. Ti mber s 5 i nches and t hi cker , 25 per cent maxi mum

c. Mat er i al s ot her t han l umber ; moi st ur e cont ent shal l be i n accor dance wi t h st andar d under whi ch t he pr oduct i s pr oduced

1. 7 PRESERVATI VE TREATMENT

Pr ovi de pr eser vat i ve t r eat ment f or :

SECTI ON 06 10 00 Page 6

a. 0. 25 pcf i nt ended f or above gr ound use.

b. 0. 40 pcf i nt ended f or gr ound cont act and f r esh wat er use. 0. 60 pcf i nt ended f or Ammoni acal Copper Quat er nar y Compound ( ACQ) - t r eat ed foundations. 0. 80 t o 1. 00 pcf i nt ended f or ACQ- t r eat ed pi l i ngs. Al l wood shal l be ai r or k i l n dr i ed af t er t r eat ment . Speci f i c t r eat ment s shal l be ver i f i ed by t he r epor t of an appr oved i ndependent i nspect i on agency, or t he AWPA Qual i t y Mar k on each pi ece. Br ush coat ar eas t hat ar e cut or dr i l l ed af t er t r eat ment wi t h ei t her t he same pr eser vat i ve used i n t he t r eat ment or wi t h a 2 per cent copper napht henat e sol ut i on.

Pl ast i c l umber shal l not be pr eser vat i ve t r eat ed. The f ol l owi ng i t ems shal l be pr eser vat i ve t r eat ed:

( 1) Wood f r ami ng, woodwor k, and pl ywood up t o and i ncl udi ng t he subf l oor i ng at t he f i r st - f l oor l evel of st r uct ur es havi ng cr awl spaces when t he bot t oms of such i t ems ar e 24 i nches or l ess f r om t he ear t h under neat h.

( 2) Wood member s t hat ar e i n cont act wi t h wat er .

( 3) Ext er i or wood st eps, pl at f or ms, and r ai l i ngs; and al l wood f r ami ng of open, r oof ed st r uct ur es.

( 4) Wood si l l s , sol es, pl at es, f ur r i ng, and sl eeper s t hat ar e l ess t han 24 i nches f r om t he gr ound, f ur r i ng and nai l er s t hat ar e set i nt o or i n cont act wi t h concr et e or masonr y.

( 5) Nai l er s, edge st r i ps, cr i cket s, cur bs, and cant s f or r oof decks.

1. 8 Cer t i f i cat es of Gr ade

Submi t cer t i f i cat es at t est i ng t hat pr oduct s meet t he gr ade r equi r ement s speci f i ed i n l i eu of gr ade mar ki ngs wher e appear ance i s i mpor t ant and gr ade mar ks wi l l def ace mat er i al .

1. 9 SUSTAI NABLE DESI GN REQUI REMENTS

See Sect i on 01 33 29 SUSTAI NABI LI TY REPORTI NG f or pr oj ect r egi onal cer t i f i ed wood and r ecycl ed cont ent r equi r ement s. Pr oduct s i n t hi s sect i on t hat cont r i but e t o t hese r equi r ement s may be avai l abl e. Composi t e wood mat er i al s shal l cont ai n no added ur ea f or mal dehyde ( LEED l ow- emi t t i ng mat er i al s) . Submi t LEED pr oduct dat a f or al l cont r i but i ng and al l appl i cabl e mat er i al s.

PART 2 PRODUCTS

2. 1 LUMBER

Fr ami ng l umber such as st uds, pl at es, caps, col l ar beams, cant st r i ps, bucks, s l eeper s, nai l i ng st r i ps, and nai l er s and boar d l umber such as subf l oor i ng and wal l and r oof sheat hi ng shal l be one of t he speci es l i s t ed i n t he t abl e bel ow. Mi ni mum gr ade of speci es shal l be as l i s t ed.

Fi nger - j oi nt ed l umber may be used i n t he same appl i cat i ons as sol i d l umber of an equi val ent speci es and gr ade, pr ovi ded t he f i nger - j oi nt ed l umber meet s al l t he r equi r ement s of t he cer t i f i cat i on and t he qual i t y cont r ol pr ogr ams of t he r ul es wr i t i ng agency havi ng j ur i sdi ct i on and al l appl i cabl e r equi r ement s of DOC/ NI ST PS56. Submi t dr awi ngs of f i el d er ect i on det ai l s f or ani l i ng st r i ps, i ncl udi ng mat er i al s and met hods of f ast eni ng nai l er s i n

SECTI ON 06 10 00 Page 7 conf or mance wi t h Fact or y Mut ual wi nd upl i f t r at ed syst ems speci f i ed i n ot her Sect i ons.

Tabl e of Gr ades f or Fr ami ng and Boar d Lumber

Gr adi ng Rul es Species Framing Boar d Lumber

WWPA G- 5 st andar d gr adi ng r ul es

Aspen, Dougl as Fi r - Lar ch, Dougl as Fi r Sout h, Engelmann Spruce-Lodgepole Pi ne, Engel mann Spr uce, Hem- Fi r , I daho Whi t e Pi ne, Lodgepol e Pi ne, Mount ai n Heml ock, Mountain Hemlock-Hem-Fir, Ponderosa Pi ne- Sugar Pi ne, Ponderosa Pine-Lodgepole Pi ne, Subal pi ne Fi r , Whi t e Woods, West er n Woods, West er n Cedar s, West er n Heml ock

Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

Al l Speci es:

No. 3 Common

WCLI B 17 st andar d gr adi ng r ul es

Dougl as Fi r - Lar ch, Hem- Fi r , Mount ai n Heml ock, Si t ka Spr uce, West er n Cedar s, West er n Hemlock

Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

Al l Speci es:

Standard

SPI B 1003 st andar d gr adi ng r ul es

Sout her n Pi ne Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

No. 2 Boar ds

SCMA Spec st andar d specifications

Cypress No. 2 Common No. 2 Common

SECTI ON 06 10 00 Page 8

Tabl e of Gr ades f or Fr ami ng and Boar d Lumber

Gr adi ng Rul es Species Framing Boar d Lumber

NELMA Gr adi ng Rul es st andar d gr adi ng r ul es

Bal sam Fi r , East er n Hemlock-Tamarack, East er n Spr uce, East er n Whi t e Pi ne, Nor t her n Pi ne, Nor t her n Pi ne- Cedar

Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

Al l Speci es:

No. 3 Common except St andar d f or East er n Whi t e and Nor t her n Pi ne

RI S Gr ade Use standard specifications

Redwood Al l Speci es:

St andar d Li ght Fr ami ng or No. 3 St r uct ur al Li ght Fr ami ng ( St ud Gr ade f or 2x4 nomi nal s i ze, 10 feet and shor t er )

Const r uct i on Hear t

NHLA Rul es r ul es f or t he measur ement and i nspect i on of har dwood and cypr ess lumber

Cypress No. 2 Di mensi on No. 2 Common

2. 2 OTHER MATERI ALS

2. 2. 1 Mi scel l aneous Wood Member s

2. 2. 1. 1 Nonst r ess Gr aded Member s

Member s shal l i ncl ude br i dgi ng, cor ner br aci ng, f ur r i ng, gr ounds, and nai l i ng st r i ps. Member s shal l be i n accor dance wi t h TABLE I f or t he speci es used. Si zes shal l be as f ol l ows unl ess ot her wi se shown:

Member Si ze ( i nches) Fur r i ng 1 x 2 Nai l i ng 1 x 3 or 1 x 4 when used as i nt er i or f i ni sh, s t r i ps ot her wi se 2 i nch st ock.

2. 2. 1. 2 Si l l Pl at es

Si l l pl at es shal l be st andar d or number 2 gr ade.

2. 2. 1. 3 Blocking

Bl ocki ng shal l be st andar d or number 2 gr ade.

2. 2. 2 Adhesives

Compl y wi t h appl i cabl e r egul at i ons r egar di ng t oxi c and hazar dous mat er i al s as speci f i ed. I nt er i or adhesi ves, seal ant s, pr i mer s and seal ant s used as

SECTI ON 06 10 00 Page 9 f i l l er shal l meet t he r equi r ement s of LEED l ow emi t t i ng mat er i al s cr edi t .

2. 3 ROUGH HARDWARE

Unl ess ot her wi se i ndi cat ed or speci f i ed, r ough har dwar e shal l be of t he t ype and si ze necessar y f or t he pr oj ect r equi r ement s. Si zes, t ypes, and spaci ng of f ast eni ngs of manuf act ur ed bui l di ng mat er i al s shal l be as r ecommended by t he pr oduct manuf act ur er unl ess ot her wi se i ndi cat ed or speci f i ed. Rough har dwar e exposed t o t he weat her or embedded i n or i n cont act wi t h pr eser vat i ve t r eat ed wood, ext er i or masonr y, or concr et e wal l s or s l abs shal l be hot - di p z i nc- coat ed i n accor dance wi t h ASTM A153/ A153M.

Nai l s and f ast eni ngs f or f i r e- r et ar dant t r eat ed l umber and woodwor k exposed t o t he weat her shal l be copper al l oy or hot - di pped gal vani zed f ast ener s as r ecommended by t he t r eat ed wood manuf act ur er .

2. 3. 1 Bol t s, Nut s, St uds, and Ri vet s

ASME B18. 2. 1, ASME B18. 5. 2. 1M, ASME B18. 5. 2. 2M and ASME B18. 2. 2.

2. 3. 2 Anchor Bol t s

ASTM A307, s i ze as i ndi cat ed, compl et e wi t h nut s and washer s.

2. 3. 3 Expansi on Shi el ds

CI D A- A- 1923, CI D A- A- 1924, and CI D A- A- 1925. Except as shown ot her wi se, maxi mum si ze of devi ces shal l be 3/ 8 i nch.

2. 3. 4 Lag Scr ews and Lag Bol t s

ASME B18. 2. 1.

2. 3. 5 Wood Scr ews

ASME B18. 6. 1.

2. 3. 6 Nails

ASTM F547, s i ze and t ype best sui t ed f or pur pose. For sheat hi ng, l engt h of nai l s shal l be suf f i c i ent t o ext end 1 i nch i nt o suppor t s. I n gener al , 8- penny or l ar ger nai l s shal l be used f or nai l i ng t hr ough 1 i nch t hi ck l umber and f or t oe nai l i ng 2 i nch t hi ck l umber ; 16- penny or l ar ger nai l s shal l be used f or nai l i ng t hr ough 2 i nch t hi ck l umber . Nai l s used wi t h t r eat ed l umber and sheat hi ng shal l be hot - di pped gal vani zed i n accor dance with ASTM A153/ A153M. Nai l i ng shal l be i n accor dance wi t h t he r ecommended nai l i ng schedul e cont ai ned i n AWC WFCM. Wher e det ai l ed nai l i ng r equi r ement s ar e not speci f i ed, nai l s i ze and spaci ng shal l be suf f i c i ent t o devel op an adequat e st r engt h f or t he connect i on. The connect i on' s st r engt h shal l be ver i f i ed agai nst t he nai l capaci t y t abl es i n AWC NDS.

Reasonabl e j udgment backed by exper i ence shal l ensur e t hat t he desi gned connect i on wi l l not cause t he wood t o spl i t . I f a l oad s i t uat i on exceeds a r easonabl e l i mi t f or nai l s, a speci al i zed connect or shal l be used.

2. 3. 7 Wi r e Nai l s

ASTM F1667.

SECTI ON 06 10 00 Page 10

2. 3. 8 Cl i p Angl es

Steel, 3/ 16 i nch t hi ck, s i ze best sui t ed f or i nt ended use; or z i nc- coat ed st eel or i r on commer ci al c l i ps desi gned f or connect i ng wood member s.

2. 3. 9 Met al Fr ami ng Anchor s

Const r uct anchor s t o t he conf i gur at i on shown usi ng hot di p z i nc- coat ed st eel conf or mi ng t o ASTM A653/ A653M, G90. Except wher e ot her wi se shown, St eel shal l be not l i ght er t han 18 gage. Speci al nai l s suppl i ed by t he manuf act ur er shal l be used f or al l nai l i ng.

2. 3. 10 Panel Edge Cl i ps

Ext r uded al umi num or gal vani zed st eel , H- shaped cl i ps t o pr event di f f er ent i al def l ect i on of r oof sheat hi ng.

PART 3 EXECUTI ON

3. 1 INSTALLATION

Conf or m t o AWC WFCM unl ess ot her wi se i ndi cat ed or speci f i ed. Sel ect l umber s i zes t o mi ni mi ze wast e. Fi t f r ami ng l umber and ot her r ough car pent r y, set accur at el y t o t he r equi r ed l i nes and l evel s, and secur e i n pl ace i n a r i gi d manner . Do not spl i ce f r ami ng member s bet ween bear i ng poi nt s. Set j oi st s, r af t er s, and pur l i ns wi t h t hei r cr own edge up. Fr ame member s f or t he passage of pi pes, condui t s, and duct s. Do not cut or bor e st r uct ur al member s f or t he passage of duct s or pi pes wi t hout appr oval . Rei nf or ce al l member s damaged by such cut t i ng or bor i ng by means of speci al l y f or med and appr oved sheet met al or bar st eel shapes, or r emove and pr ovi de new, as appr oved. Pr ovi de as necessar y f or t he pr oper compl et i on of t he wor k al l f r ami ng member s not i ndi cat ed or speci f i ed. Spi k i ng and nai l i ng not i ndi cat ed or speci f i ed ot her wi se shal l be i n accor dance wi t h t he Nai l i ng Schedul e cont ai ned i n I CC I BC; per f or m bol t i ng i n an appr oved manner .

Spi kes, nai l s, and bol t s shal l be dr awn up t i ght . Use sl at e or st eel shi ms when l evel i ng j oi st s, beams, and gi r der s on masonr y or concr et e. Do not use shi mmi ng on wood or met al bear i ngs. When j oi s t s, beams, and gi r der s ar e pl aced on masonr y or concr et e, a wood base pl at e shal l be posi t i oned and l evel ed wi t h gr out . The j oi s t , beam, or gi r der shal l t hen be pl aced on t he pl at e. When j oi st s, beams, and gi r der s ar e set i nt o masonr y or concr et e, a pocket shal l be f or med i nt o t he wal l . The j oi st , beam, or gi r der shal l t hen be pl aced i nt o t he pocket and l evel ed wi t h a st eel shi m.

3. 1. 1 Sills

Set s i l l s l evel and squar e and wedge wi t h st eel or s l at e shi ms; poi nt or gr out wi t h non- shr i nki ng cement mor t ar t o pr ovi de cont i nuous and sol i d bear i ng. Anchor s i l l s t o t he f oundat i ons as i ndi cat ed. Wher e s i zes and spaci ng of anchor bol t s ar e not i ndi cat ed, pr ovi de not l ess t han 5/ 8 i nch di amet er bol t s at al l cor ner s and spl i ces and space at a maxi mum of 6 f eet

o. c. bet ween cor ner bol t s. Pr ovi de at l east t wo bol t s f or each si l l member . Lap and spl i ce s i l l s at cor ner s and bol t t hr ough t he l aps or but t t he ends and t hr ough- bol t not mor e t han 6 i nches f r om t he ends. Pr ovi de bol t s wi t h pl at e washer s and nut s. Bol t s i n ext er i or wal l s shal l be zinc-coated.

3. 1. 2 Anchor s i n Masonr y

Except wher e i ndi cat ed ot her wi se, embed anchor bol t s not l ess t han 15 i nches

SECTI ON 06 10 00 Page 11 i n masonr y uni t wal l s and pr ovi de each wi t h a nut and a 2 i nch di amet er washer at bot t om end. Ful l y gr out bol t s wi t h mor t ar .

3. 1. 3 Anchor s i n Concr et e

Except wher e i ndi cat ed ot her wi se, embed anchor bol t s not l ess t han 8 i nches i n pour ed concr et e wal l s and pr ovi de each wi t h a nut and a 2 i nch di amet er washer at bot t om end. A bent end may be subst i t ut ed f or t he nut and washer ; bend shal l be not l ess t han 90 degr ees. Powder - act uat ed f ast ener s spaced 3 f eet o. c. may be pr ovi ded i n l i eu of bol t s f or s i ngl e t hi ckness pl at es on concr et e.

3. 2 MISCELLANEOUS

3. 2. 1 Wood Roof Nai l er s, Edge St r i ps, Cr i cket s, Cur bs, and Cant s

Pr ovi de s i zes and conf i gur at i ons i ndi cat ed or speci f i ed and anchor ed secur el y t o cont i nuous const r uct i on.

3. 2. 1. 1 Roof Edge St r i ps and Nai l er s

Pr ovi de at per i met er of r oof , ar ound openi ngs t hr ough r oof , and wher e r oof s abut wal l s, cur bs, and ot her ver t i cal sur f aces. Except wher e i ndi cat ed ot her wi se, nai l er s shal l be 6 i nches wi de and t he same t hi ckness as t he i nsul at i on. Anchor nai l er s secur el y t o under l y i ng const r uct i on. Anchor per i met er nai l er s i n accor dance wi t h FM 4435.

3. 2. 1. 2 Cr i cket s, Cant s, and Cur bs

Pr ovi de wood saddl es or cr i cket s, cant st r i ps, cur bs f or scut t l es and vent i l at or s, and wood nai l er s bol t ed t o t ops of concr et e or masonr y cur bs and at expansi on j oi nt s, as i ndi cat ed, speci f i ed, or necessar y and of lumber.

3. 2. 2 Wood Bl ocki ng

Pr ovi de pr oper s i zes and shapes at pr oper l ocat i ons f or t he i nst al l at i on and at t achment of wood and ot her f i ni sh mat er i al s, f i x t ur es, equi pment , and i t ems i ndi cat ed or speci f i ed.

3. 2. 3 Wood Gr ounds

Pr ovi de f or f ast eni ng wood t r i m, f i ni sh mat er i al s, and ot her i t ems t o pl ast er ed wal l s and cei l i ngs. I nst al l gr ounds i n pr oper al i gnment and t r ue wi t h an 8 f oot st r ai ght edge.

3. 2. 4 Wood Fur r i ng

Pr ovi de wher e shown and as necessar y f or f aci ng mat er i al s speci f i ed. Except as shown ot her wi se, f ur r i ng st r i ps shal l be nomi nal one by 3, cont i nuous, and spaced 16 i nches o. c. Er ect f ur r i ng ver t i cal l y or hor i zont al l y as necessar y. Nai l f ur r i ng st r i ps t o masonr y. Do not use wood pl ugs.

Pr ovi de f ur r i ng st r i ps ar ound openi ngs, behi nd bases, and at angl es and cor ner s. Fur r i ng shal l be pl umb, r i gi d, and l evel and shal l be shi mmed as necessar y t o pr ovi de a t r ue, even pl ane wi t h sur f aces sui t abl e t o r ecei ve t he f i ni sh r equi r ed. For m f ur r i ng f or of f set s and br eaks i n wal l s or cei l i ngs on 1 by 4 wood st r i ps spaced 16 i nches o. c.

SECTI ON 06 10 00 Page 12

3. 2. 5 Tempor ar y Cl osur es

Pr ovi de wi t h hi nged door s and padl ocks and i nst al l dur i ng const r uct i on at ext er i or door ways and ot her gr ound l evel openi ngs t hat ar e not ot her wi se c l osed. Cover wi ndows and ot her unpr ot ect ed openi ngs wi t h pol yet hyl ene or ot her appr oved mat er i al , s t r et ched on wood f r ames. Pr ovi de dust pr oof bar r i er par t i t i ons t o i sol at e ar eas as di r ect ed.

3. 2. 6 Tempor ar y Cent er i ng, Br aci ng, and Shor i ng

For ms and cent er i ng f or cast - i n- pl ace concr et e wor k ar e speci f i ed i n Section 03 30 00 CAST- I N- PLACE CONCRETE.

3. 2. 7 Si l l Pl at es

Si l l pl at es shal l be set l evel and squar e and anchor bol t ed at not mor e t han 6 f eet on cent er s and not mor e t han 12 i nches f r om end of each pi ece. A mi ni mum of 2 anchor s shal l be used f or each pi ece.

- - End of Sect i on - -

SECTI ON 06 10 00 Page 13

SECTI ON TABLE OF CONTENTS

DI VI SI ON 06 - WOOD, PLASTI CS, AND COMPOSI TES

SECTI ON 06 20 00

FI NI SH CARPENTRY

02/12

PART 1 GENERAL

1. 1 REFERENCES

1. 2 SUBMI TTALS

1. 3 DETAI L DRAWI NGS

1. 4 CERTI FI CATES

1. 5 DELI VERY, STORAGE, AND HANDLI NG

1. 6 QUALI TY ASSURANCE

1. 6. 1 Lumber

1. 6. 2 Pl ywood

1. 6. 3 Pr essur e- Tr eat ed Lumber and Pl ywood

1. 6. 4 Nonpr essur e- Tr eat ed Woodwor k and Mi l l wor k

1. 6. 5 Fi r e- Ret ar dant Tr eat ed Lumber

1. 7 SUSTAI NABLE DESI GN REQUI REMENTS

PART 2 PRODUCTS

2. 1 WOOD

2. 1. 1 Si zes and Pat t er ns of Wood Pr oduct s

2. 1. 2 Tr i m, Fi ni sh, and Fr ames

2. 1. 3 Sof t wood Pl ywood

2. 1. 4 Har dwood Pl ywood

2. 2 MOI STURE CONTENT OF WOOD PRODUCTS

2. 3 PRESERVATI VE TREATMENT OF WOOD PRODUCTS

2. 4 FI RE- RETARDANT TREATMENT

2. 5 HARDWARE

2. 5. 1 Wood Scr ews

2. 5. 2 Bol t s, Nut s, Lag Scr ews, and St uds

2. 5. 3 Nai l s

2. 6 FABRI CATI ON

2. 6. 1 Qual i t y St andar ds ( QS)

2. 6. 2 Tr anspar ent Wood Fi ni sh

PART 3 EXECUTI ON

3. 1 FI NI SH WORK

3. 2 SHELVI NG

SECTI ON 06 20 00 Page 1

SECTI ON 06 20 00

FI NI SH CARPENTRY

02/12

PART 1 GENERAL

1. 1 REFERENCES

The publ i cat i ons l i s t ed bel ow f or m a par t of t hi s speci f i cat i on t o t he ext ent r ef er enced. The publ i cat i ons ar e r ef er r ed t o wi t hi n t he t ext by t he basi c desi gnat i on onl y.

AMERI CAN LUMBER STANDARDS COMMI TTEE ( ALSC)

ALSC PS 20 ( 2015) Amer i can Sof t wood Lumber St andar d

AMERI CAN WOOD PROTECTI ON ASSOCI ATI ON ( AWPA)

AWPA M2 ( 2016) St andar d f or t he I nspect i on of Pr eser vat i ve Tr eat ed Wood Pr oduct s f or I ndust r i al Use

AWPA M4 ( 2015) St andar d f or t he Car e of Pr eser vat i ve- Tr eat ed Wood Pr oduct s

AWPA P5 ( 2015) St andar d f or Wat er bor ne Preservatives

AWPA U1 ( 2017) Use Cat egor y Syst em: User Speci f i cat i on f or Tr eat ed Wood

APA - THE ENGI NEERED WOOD ASSOCI ATI ON ( APA)

APA L870 ( 2010) Vol unt ar y Pr oduct St andar d, PS 1- 09, St r uct ur al Pl ywood

ASME I NTERNATI ONAL ( ASME)

ASME B18. 2. 1 ( 2012; Er r at a 2013) Squar e and Hex Bol t s and Scr ews ( I nch Ser i es)

ASME B18. 2. 2 ( 2015) Nut s f or Gener al Appl i cat i ons:

Machi ne Scr ew Nut s, Hex, Squar e, Hex Fl ange, and Coupl i ng Nut s ( I nch Ser i es)

ASME B18. 6. 1 ( 2016) Wood Scr ews ( I nch Ser i es)

ASTM I NTERNATI ONAL ( ASTM)

ASTM D2898 ( 2010; R 2017) St andar d Pr act i ce f or Accel er at ed Weat her i ng of Fi r e- Ret ar dant - Tr eat ed Wood f or Fi r e Testing

ASTM F547 ( 2017) St andar d Ter mi nol ogy of Nai l s f or Use wi t h Wood and Wood- Base Mat er i al s

SECTI ON 06 20 00 Page 2

HARDWOOD PLYWOOD AND VENEER ASSOCI ATI ON ( HPVA)

HPVA HP- 1 ( 2016) Amer i can Nat i onal St andar d f or Har dwood and Decor at i ve Pl ywood

NATI ONAL HARDWOOD LUMBER ASSOCI ATI ON ( NHLA)

NHLA Rul es ( 2015) Rul es f or t he Measur ement & I nspect i on of Har dwood & Cypr ess

NORTHEASTERN LUMBER MANUFACTURERS ASSOCI ATI ON ( NELMA)

NELMA Gr adi ng Rul es ( 2013) St andar d Gr adi ng Rul es f or Nor t heast er n Lumber

REDWOOD I NSPECTI ON SERVI CE ( RI S) OF THE CALI FORNI A REDWOOD

ASSOCI ATI ON ( CRA)

RI S Gr ade Use ( 1998) Redwood Lumber Gr ades and Uses

SOUTHERN PI NE I NSPECTI ON BUREAU ( SPI B)

SPI B 1003 ( 2014) St andar d Gr adi ng Rul es f or Sout her n Pi ne Lumber

WEST COAST LUMBER I NSPECTI ON BUREAU ( WCLI B)

WCLI B 17 ( 2015) St andar d Gr adi ng Rul es

WESTERN WOOD PRODUCTS ASSOCI ATI ON ( WWPA)

WWPA G- 5 ( 2017) West er n Lumber Gr adi ng Rul es

WI NDOW AND DOOR MANUFACTURERS ASSOCI ATI ON ( WDMA)

WDMA I . S. 4 ( 2015A) Pr eser vat i ve Tr eat ment f or Mi l l wor k

WOODWORK I NSTI TUTE ( WI )

NAAWS 3. 1 ( 2017; 2018 Er r at a Edi t i on) Nor t h Amer i can Ar chi t ect ur al Woodwor k St andar ds

1. 2 SUBMITTALS

Gover nment appr oval i s r equi r ed f or submi t t al s wi t h a " G" desi gnat i on;

submi t t al s not havi ng a " G" desi gnat i on ar e f or i nf or mat i on onl y. When used, a desi gnat i on f ol l owi ng t he " G" desi gnat i on i dent i f i es t he of f i ce t hat wi l l r evi ew t he submi t t al f or t he Gover nment . Submi t t he f ol l owi ng i n accor dance wi t h Sect i on 01 33 00 SUBMI TTAL PROCEDURES:

SD- 02 Shop Dr awi ngs

Det ai l Dr awi ngs

SD- 03 Pr oduct Dat a

LEED dat a f or r ecycl ed cont ent , r egi onal mat er i al s, cer t i f i ed wood, l ow- emi t t i ng mat er i al s.

SECTI ON 06 20 00 Page 3

SD- 07 Cer t i f i cat es

Cer t i f i cat es of gr ade Cer t i f i cat es of compl i ance

1. 3 DETAI L DRAWI NGS

The Cont r act or shal l submi t det ai l dr awi ngs showi ng f abr i cat ed i t ems and speci al mi l l and woodwor k i t ems. Dr awi ngs shal l i ndi cat e mat er i al s and det ai l s of const r uct i on, met hods of f ast eni ng, er ect i on, and i nst al l at i on.

1. 4 CERTIFICATES

Provide cer t i f i cat es of gr ade f r om t he gr adi ng agency on gr aded but unmar ked l umber or pl ywood at t est i ng t hat mat er i al s meet t he gr ade r equi r ement s speci f i ed her ei n.

Provide cer t i f i cat es of compl i ance unl ess mat er i al s bear cer t i f i cat i on mar ki ngs or st at ement s.

1. 5 DELI VERY, STORAGE, AND HANDLI NG

Del i ver l umber , pl ywood, t r i m, and mi l l wor k t o j ob s i t e i n an undamaged condi t i on. St ack mat er i al s t o ensur e vent i l at i on and dr ai nage. Pr ot ect agai nst dampness bef or e and af t er del i ver y. St or e mat er i al s under cover i n a wel l - vent i l at ed encl osur e and pr ot ect agai nst ext r eme changes i n t emper at ur e and humi di t y. Do not st or e pr oduct s i n bui l di ng unt i l wet t r ade mat er i al s ar e dr y.

1. 6 QUALI TY ASSURANCE

1. 6. 1 Lumber

I dent i f y each pi ece or each bundl e of l umber , mi l l wor k, and t r i m by t he gr ade mar k of a r ecogni zed associ at i on or i ndependent i nspect i on agency t hat i s cer t i f i ed by t he Boar d of Revi ew, Amer i can Lumber St andar ds Commi t t ee, t o gr ade t he speci es.

1. 6. 2 Plywood

Each sheet of pl ywood shal l bear t he mar k of a r ecogni zed associ at i on or i ndependent i nspect i on agency t hat mai nt ai ns cont i nui ng cont r ol over qual i t y of t he pl ywood. Mar k shal l i dent i f y pl ywood by speci es gr oup or span r at i ng, and shal l show exposur e dur abi l i t y c l assi f i cat i on, gr ade, and compl i ance wi t h APA L870.

1. 6. 3 Pr essur e- Tr eat ed Lumber and Pl ywood

Each t r eat ed pi ece shal l be i nspect ed i n accor dance wi t h AWPA M2.

1. 6. 4 Nonpr essur e- Tr eat ed Woodwor k and Mi l l wor k

Mar k, st amp, or l abel , i ndi cat i ng compl i ance wi t h WDMA I . S. 4.

1. 6. 5 Fi r e- Ret ar dant Tr eat ed Lumber

Each pi ece t o bear Under wr i t er s Labor at or i es l abel or t he l abel of anot her nat i onal l y r ecogni zed i ndependent t est i ng l abor at or y.

SECTI ON 06 20 00 Page 4

1. 7 SUSTAI NABLE DESI GN REQUI REMENTS

See Sect i on 01 33 29 SUSTAI NABI LI TY REPORTI NG f or pr oj ect r egi onal cer t i f i ed wood and r ecycl ed cont ent r equi r ement s. Pr oduct s i n t hi s Sect i on t hat cont r i but e t o t hese r equi r ement s may be avai l abl e. Composi t e wood mat er i al s shal l cont ai n no added ur ea f or mal dehyde ( LEED l ow- emi t t i ng mat er i al s) . Fi el d- appl i ed i nt er i or adhesi ves and seal ant s shal l meet LEED l ow- emi t t i ng mat er i al s r equi r ement s. Submi t LEED pr oduct dat a f or al l cont r i but i ng and al l appl i cabl e mat er i al s.

PART 2 PRODUCTS

2. 1 WOOD

2. 1. 1 Si zes and Pat t er ns of Wood Pr oduct s

Yar d and boar d l umber s i zes shal l conf or m t o ALSC PS 20. Pr ovi de shaped l umber and mi l l wor k i n t he pat t er ns i ndi cat ed and st andar d pat t er ns of t he associ at i on cover i ng t he speci es. Si ze r ef er ences, unl ess ot her wi se speci f i ed, ar e nomi nal s i zes, and act ual s i zes shal l be wi t hi n manuf act ur i ng t ol er ances al l owed by t he appl i cabl e st andar d.

2. 1. 2 Tr i m, Fi ni sh, and Fr ames

Pr ovi de speci es and gr ades l i s t ed f or mat er i al s t o be pai nt f i ni shed.

Pr ovi de mat er i al s t hat ar e t o be st ai n, nat ur al , or t r anspar ent f i ni shed one gr ade hi gher t han t hat l i s t ed. Pr ovi de speci es i ndi cat ed f or mat er i al s t o be t r anspar ent f i ni shed. Run t r i m, except wi ndow st ool s and apr ons wi t h hol l ow backs.

TABLE OF GRADES FOR WOOD TO RECEI VE PAI NT FI NI SH

Gr adi ng Rul es Species Ext er i or and I nt er i or Tr i m, Fi ni sh, and Fr ames

WWPA G- 5

st andar d gr adi ng rules

Aspen, Dougl as Fi r - Lar ch, Dougl as Fi r Sout h, Engel mann Spr uce- Lodgepol e Pi ne, Engel mann Spr uce, Hem- Fi r , I daho Whi t e Pi ne, Lodgepol e Pi ne, Mount ai n Heml ock, Mount ai n Heml ock- Hem- Fi r , Ponder osa Pi ne- Sugar Pi ne, ( Ponder osa Pi ne- Lodgepol e Pi ne, ) Whi t e Woods, ( West er n Woods, ) West er n Cedar s, West er n Heml ock

Al l Speci es: C & Bt r .

Sel ect ( Choi ce & Bt r I daho Whi t e Pi ne) or Super i or Fi ni sh. West er n Red Cedar may be gr aded C & Bt r .

Sel ect or A & Bt r . per Speci al West er n Red Cedar Rules.

WCLI B 17

st andar d gr adi ng rules

Dougl as Fi r - Lar ch, Hem- Fi r , Mount ai n Heml ock, Si t ka Spr uce, West er n Cedar s, West er n Heml ock

Al l Speci es: C & Bt r VG, except A f or West er n Red Cedar

SPI B 1003

st andar d gr adi ng rules

Sout her n Pi ne C & Bt r

NHLA Rul es Cypress C-Select

SECTI ON 06 20 00 Page 5

TABLE OF GRADES FOR WOOD TO RECEI VE PAI NT FI NI SH

Gr adi ng Rul es Species Ext er i or and I nt er i or Tr i m, Fi ni sh, and Fr ames

NELMA Gr adi ng Rul es st andar d gr adi ng r ul es

Bal sam Fi r , East er n Heml ock- Tamar ack, East er n Spr uce, East er n Whi t e Pi ne, Nor t her n Pi ne, Nor t her n Pi ne, Nor t her n Whi t e Cedar

Al l Speci es: C- Sel ect except C & BTR f or East er n Whi t e Pi ne and Nor way Pi ne

RI S Gr ade Use standard specifications

Redwood Cl ear , Cl ear Al l Hear t

NHLA Rul es Cypress B Fi ni sh

Red Gum, Sof t El m, Bi r ch Sel ect or BTR ( f or i nt er i or use onl y)

2. 1. 3 Sof t wood Pl ywood

APA L870, t hi cknesses as i ndi cat ed.

a. Pl ywood f or Shel v i ng: I nt er i or t ype, A- B Gr ade, any speci es gr oup.

2. 1. 4 Har dwood Pl ywood

HPVA HP- 1, Type I I ( I nt er i or ) , Pr emi um ( A) Gr ade, l umber cor e const r uct i on, f ace veneer s of r ed oak, of t hi ckness i ndi cat ed.

2. 2 MOI STURE CONTENT OF WOOD PRODUCTS

Ai r - dr y or k i l n- dr y l umber . Ki l n- dr y t r eat ed l umber af t er t r eat ment .

Maxi mum moi st ur e cont ent of wood pr oduct s at t i me of del i ver y t o t he j ob s i t e, and when i nst al l ed, shal l be as f ol l ows:

a. I nt er i or Fi ni sh Lumber , Tr i m, and Mi l l wor k 1- 1/ 4 I nches Nomi nal or Less i n Thi ckness: 6 per cent on 85 per cent of t he pi eces and 8 per cent on remainder.

b. Moi st ur e cont ent of ot her mat er i al s shal l be i n accor dance wi t h t he appl i cabl e st andar ds.

2. 3 PRESERVATI VE TREATMENT OF WOOD PRODUCTS

Lumber and pl ywood used on t he ext er i or of bui l di ngs or i n cont act wi t h masonr y or concr et e shal l be pr essur e- t r eat ed wi t h wat er - bor ne pr eser vat i ve l i s t ed i n AWPA P5 as appl i cabl e, and i nspect ed i n accor dance wi t h AWPA M2.

I dent i f y t r eat ment on each pi ece of mat er i al by t he qual i t y mar k of an agency accr edi t ed by t he Boar d of Revi ew of t he Amer i can Lumber St andar ds Committee. Exposed ar eas of t r eat ed wood t hat ar e cut or dr i l l ed af t er t r eat ment shal l r ecei ve a f i el d t r eat ment i n accor dance wi t h AWPA M4.

I t ems of al l - hear t mat er i al of cedar , cypr ess, or r edwood wi l l not r equi r e pr eser vat i ve t r eat ment , except when i n di r ect cont act wi t h soi l .

2. 4 FI RE- RETARDANT TREATMENT

Pr essur e t r eat f i r e- r et ar dant t r eat ed l umber and pl ywood i n accor dance wi t h

SECTI ON 06 20 00 Page 6

AWPA U1. Compl y wi t h mat er i al use as def i ned i n AWPA U1 f or I nt er i or Type A and Ext er i or Type. Tr eat ment and per f or mance i nspect i on must be conduct ed by a qual i f i ed i ndependent t est i ng agency t hat est abl i shes per f or mance r at i ngs. Each pi ece or bundl e of t r eat ed mat er i al must bear i dent i f i cat i on of t he t est i ng agency t o i ndi cat e per f or mance wi t h such r at i ng. Subj ect t r eat ed mat er i al s t hat wi l l be exposed t o r ai n wet t i ng t o an accel er at ed weat her i ng t echni que i n accor dance wi t h ASTM D2898, Met hod A, pr i or t o bei ng t est ed f or compl i ance wi t h AWPA U1.

Pr ovi de f i r e- r et ar dant t r eat ed panel backboar ds as i ndi cat ed i n el ect i cal drawings.

2. 5 HARDWARE

Pr ovi de s i zes, t ypes, and spaci ngs of manuf act ur ed bui l di ng mat er i al s r ecommended by t he pr oduct manuf act ur er except as ot her wi se i ndi cat ed or specified.

2. 5. 1 Wood Scr ews

ASME B18. 6. 1.

2. 5. 2 Bol t s, Nut s, Lag Scr ews, and St uds

ASME B18. 2. 1 and ASME B18. 2. 2.

2. 5. 3 Nails

Nai l s shal l be t he s i ze and t ype best sui t ed f or t he pur pose and shal l conf or m t o ASTM F547. Nai l s shal l be hot - di p gal vani zed or al umi num when used on ext er i or wor k. For s i di ng, l engt h of nai l s shal l be suf f i c i ent t o extend 1- 1/ 2 i nches i nt o suppor t s, i ncl udi ng wood sheat hi ng over f r ami ng.

Scr ews f or use wher e nai l i ng i s i mpr act i cal shal l be s i ze best sui t ed f or purpose.

2. 6 FABRICATION

2. 6. 1 Qual i t y St andar ds ( QS)

The t er ms " Pr emi um, " " Cust om, " and " Economy" r ef er t o t he qual i t y gr ades def i ned i n NAAWS 3. 1. I t ems not speci f i ed t o be of a speci f i c gr ade shal l be Cust om gr ade. The AWI QS i s super seded by al l cont r act document r equi r ement s i ndi cat ed or st at ed her ei n.

2. 6. 2 Tr anspar ent Wood Fi ni sh

Pr ovi de a nat ur al f act or y f i ni sh on wood sur f aces af t er f abr i cat i on.

Fi ni sh shal l be f abr i cat or ' s st andar d nat ur al f i ni sh, except t hat i t shal l be equi val ent t o one coat of seal er and one coat of spar var ni sh on t he sur f aces and a second coat of spar var ni sh on sur f aces exposed t o v i ew.

Sand l i ght l y and wi pe c l ean bet ween coat s. See Sect i on 09 06 00 SCHEDULES

FOR FI NI SHES.

PART 3 EXECUTI ON

3. 1 FI NI SH WORK

Pr ovi de s i zes, mat er i al s, and desi gns as i ndi cat ed and as speci f i ed. Appl y pr i mer t o f i ni sh wor k bef or e i nst al l i ng. Wher e pr act i cabl e, shop assembl e

SECTI ON 06 20 00 Page 7 and f i ni sh i t ems of bui l t - up mi l l wor k. Joi nt s shal l be t i ght and const r uct ed i n a manner t o conceal shr i nkage. Mi t er t r i m and mol di ngs at ext er i or angl es and cope at i nt er i or angl es and at r et ur ns. Mat er i al shal l show no war p af t er i nst al l at i on. I nst al l mi l l wor k and t r i m i n maxi mum pr act i cal l engt hs. Fast en f i ni sh wor k wi t h f i ni sh nai l s. Pr ovi de bl i nd nai l i ng wher e pr act i cabl e. Set f ace nai l s f or put t y st oppi ng.

Af t er i nst al l at i on of i nt er i or f i ni sh wor k, sand exposed sur f aces smoot h.

Pr ovi de wi ndow and door t r i m i n s i ngl e l engt hs.

3. 2 SHELVING

Pl ywood shel f mat er i al wi t h sol i d wood edge bandi ng suppor t ed subst ant i al l y wi t h end and i nt er medi at e suppor t s and ar r anged t o pr event buckl i ng and saggi ng. Thi ckness and si zes as i ndi cat ed. Pr ovi de c l eat s except wher e hook st r i ps ar e speci f i ed or i ndi cat ed. Shel v i ng t o have t r anspar ent wood f i ni sh.

SECTI ON 06 20 00 Page 8

SECTI ON TABLE OF CONTENTS

DI VI SI ON 06 - WOOD, PLASTI CS, AND COMPOSI TES

SECTI ON 06 41 16

LAMI NATE CLAD ARCHI TECTURAL CASEWORK

08/10

PART 1 GENERAL

1. 1 REFERENCES

1. 2 SYSTEM DESCRI PTI ON

1. 3 SUSTAI NABI LI TY REQUI REMENTS

1. 4 SUBMI TTALS

1. 5 QUALI TY ASSURANCE

1. 5. 1 Gener al Requi r ement s

1. 5. 2 Mock- ups

1. 6 DELI VERY, STORAGE, AND HANDLI NG

1. 7 SEQUENCI NG AND SCHEDULI NG

PART 2 PRODUCTS

2. 1 WOOD MATERI ALS

2. 1. 1 Lumber

2. 1. 2 Panel Pr oduct s

2. 1. 2. 1 Pl ywood

2. 1. 2. 2 Par t i c l eboar d

2. 1. 2. 3 Medi um Densi t y Fi ber boar d

2. 2 SOLI D POLYMER MATERI AL

2. 3 HI GH PRESSURE DECORATI VE LAMI NATE ( HPDL)

2. 3. 1 Hor i zont al Gener al Pur pose St andar d ( HGS) Gr ade

2. 3. 2 Ver t i cal Gener al Pur pose St andar d ( VGS) Gr ade

2. 3. 3 Hor i zont al Gener al Pur pose Post f or mabl e ( HGP) Gr ade

2. 3. 4 Ver t i cal Gener al Pur pose Post f or mabl e ( VGP) Gr ade

2. 3. 5 Backi ng Sheet ( BK) Gr ade

2. 4 THERMOSET DECORATI VE OVERLAYS ( MELAMI NE)

2. 5 EDGE BANDI NG

2. 6 CABI NET HARDWARE

2. 6. 1 Door Hi nges

2. 6. 2 Cabi net Pul l s

2. 6. 3 Dr awer Sl i de

2. 6. 4 Adj ust abl e Shel f Suppor t Syst em

2. 6. 5 Cabi net Locks

2. 7 FASTENERS

2. 8 ADHESI VES, CAULKS, AND SEALANTS

2. 8. 1 Adhesi ves

2. 8. 1. 1 Wood Joi ner y

2. 8. 1. 2 Lami nat e Adhesi ve

2. 8. 2 Caul k

2. 8. 3 Seal ant

2. 9 WOOD FI NI SHES

2. 10 GROMMETS

2. 11 FABRI CATI ON

2. 11. 1 Cabi net Fl oor Base

SECTI ON 06 41 16…