Appendixs_EE_-_CID_Package.pdf

REQUEST FOR PROPOSAL: DESIGN BUILD 05 OCTOBER 2016

RENOVATE DORMITORY BUILDING 98, THULE AIR BASE, GREENLAND

Appendices

APPENDIX EE

COMPREHENSIVE INTERIOR DESIGN (CID) PACKAGE

THIS PAGE INTENTIONALLY LEFT BLANK

29 CID (Concept Phase)

Repair Dormitory Building 98 Thule Air Base, Greenland

05 October 2016

Prepared for:

U.S. Army Corps of Engineers

Air Force Space Command

Prepared by:

Jacobs/Ammann & Whitney

299 Madison Ave, Suite 1

JACOBS / AMMANN & WHITNEY

299 Madison

Repair Dormitory, Building 98

Concept Phase Submission October 5, 2016

Proj. No. : WWCX-10-3006

Table of Contents

Chapter 1 – General Information

1.1 Statement of Design Objectives

1.2 Structural Interior Design (SID) Manufacturer Summary List

1.3 Furniture, Fixtures & Equipment (FF&E) Manufacturer Summary List

Chapter 2 – Structural Interior Design

2.1 Room Finish and Finish Material Key Schedule

I-601 Interior Finish and Interior Finish Materials Key-Structural

2.2 Colorboards

2.2.1 Interior Finishes

2.3 Material Cut Sheets

2.4 Warranties

Chapter 3 – Comprehensive Interior Design

3.1 Furniture Plans

I-101 First Floor Furniture Plan

I-102 Second Floor Furniture Plan

I-103 Third Floor Furniture Plan

3.2 Enlarged Furniture Plans

I-401 Enlarged Furniture Plans – First Floor

I-402 Enlarged Furniture Plans – Second and Third Floors

3.3 Furniture Order Forms

Chapter 1 – General Information

1.1 Statement of Design Objectives

The Comprehensive Interior Design (CID) package for the Thule Dormitory in Greenland provides the specifications, selections and warranty information for the interior finishes and furniture of this facility. This package is being developed to meet the furniture and finish requirements for this project. Finishes and furniture have been selected with the chosen ‘Recycled Glass’ CID motif selected by Air Force Officials for this particular building.

A. Function: The relationship of all interior and exterior spaces has been developed to facilitate daily operations, enhance operational efficiencies, and provide customer satisfaction.

B. Cost Effectiveness: All finishes provided will reflect the best value in terms of aesthetic value and life-cycle costs. There will be consideration in appointing funds to appropriate locations. Areas that provide the most impact on the customer’s experience will be considered important locations.

C. Durability: Selection of quality materials will ensure that the facility will look fresh and clean for years to come.

D. Maintainability: Finishes will be selected to limit future maintenance requirements.

E. Design: The design objective of this facility is simple; people should feel comfortable and productive in their living and work environment.

F. Creativity: The project will rely on innovation and creativity in color and style. Providing the best value is the goal for the functions of this facility and the personnel who will use it.

G. Flexibility: Where finishes are more imbedded into the building design, such as porcelain tile, a more neutral color scheme is appropriate. Finishes that can be updated easily, such as paint, allow for more popular colors to be used. This allows for future renovations with little cost impact.

H. Timelessness: The interior image of this building should stand the test of time and minimize becoming outdated. Materials and finishes that relate to a more timeless standard or that may be easily updated with minimal cost will be incorporated.

I. Sustainability: Creating a healthy building for its users and for our planet will be at the forefront of the design. Finishes and adhesives with low VOC’s will help maintain a healthy indoor environment.

Natural or recycled/recyclable materials will be a part of the design where possible. Also, materials that do not need a lot of maintenance will aid in the sustainability effort.

1.2 SID Manufacturer Summary

List

Armstrong Flügger A/S JJ Haines & Company Islevdalvej 151 6950 Aviation Blvd. 2610 Rødovre Glen Burnie, MD 21061 Tel: +45 70 15 15 05 Tel: 800.638.1406 X2022 E-mail: flugger@flugger.com A/S reg. nr. 46.095 Tandus Flooring CVR-nr. 32788718 311 Smith Industrial Blvd.

PO Box 1147 Dalton, GA 30722-1447 Tel: 800.248.2878

Daltile 791 Paul Birch Drive Crownsville, MD 21032 Tel: 410.923.5680 Fax: 410.923.5681

StarQuartz Industries, Inc.

211 Boston Street Middleton, MA 01949 Tel: 800.726.7845 Fax: 978.750.7306

Mats Inc.

P.O. Box 839 37 Shuman Avenue Stoughton, MA 02072 Tel: 800.MATS.INC Fax: 781.344.1537

Armstrong Denmark A/S Naverland 8 DK-2600 Glostrup Denmark Tel: +45 44 91 00 36 Fax: +45 44 91 06 10

1.3 FF&E Manufacturer Summary List

Avanti Products The HON Company 10880 NW 30th Street 200 Oak Street Miami, FL 33172 Muscatine, Iowa 52761 Tel: 800.323.5029 Tel: 563.272.7100 Fax: 305.591.3629

Bosch Kitchen Aid 5551 McFadden Ave. 553 Benson Rd.

Huntington Beach, CA 92649 Benton Harbor, MI 49022 Tel: 800.944.2904 Tel: 800.422.1230 Fax: 714.901.5360

Broan Nu-Tone, LLC. Maharam P.O. Box 270140 146 Greene Street Hartford, WI 53027 New York, NY 10012 Tel: 800.558.1711 Tel: 212.334.7222

Casson Art Nessen Lighting Accessories for Contract Sales, Inc. P.O. Box 187 Customer Service 420 Railroad Way P.O. Box 4187 Mamaroneck, NY 10543 Martinsville, VA 24115 Tel: 914.698.7799 Tel: 800.550.4278 Fax: 914.698.5577

Follett Corporation Quiltcraft 801 Church Lane 1230 East Ledbetter Drive Easton, PA 18040 Dallas, TX 75216 Tel: 800.523.9361 Tel: 214.376.1841 Fax: 610.250.0696

GE Appliances Whirlpool GE Answer Center 553 Benson Road Tel: 800.626.2005 Benson Harbor, MI 49022 Tel: 866.698.2538

IDEmobler Max Jessen A/S Industrivej 2 Thomasville Contract Group DK-9575 Terndrup Tel: 636.537.9548 Tel: +45 9833 5333 Fax: 636.778.9278 Fax: +45 9833 6111

1.3 FF&E Manufacturer Summary List

(Continued)

HTH Headquarter

HTH Kitchen

Industrivej 6

DK-6870 Ølgod Tel: +75 24 4777 Catalogue link: http://www.hth-kitchen.com/view-catalouge/

American Energy Restaurant Equipment 7538 Fullerton Court Springfield, VA 22153

Tel: 703.644.6666

Chapter 2 – Structural Interior Design

2.1 Room Finish and Finish Materials Key Schedule

2.2 Colorboards

2.2.1 Interior Finishes

SU-1

SU-4

BS-1

VFC-1

P-1 – P-4 P-1, 2, 3, 4

CPT-1

P-5

SU-4

GFC-1, 2

SU-2

SU-3

PT-1, PTB-1

PT-2

ACT-1

GT-1

MAT-1

PLAM-1

2.3 Material Cut Sheets

DUNE™

Square Lay-in & Tegular fine texture

Dune™ Square Lay-in panels with Prelude® XL® 15/16" suspension system (Pgs. 279-280)

Dune Tegular panels with Interlude® XL HRC 9/16" suspension system (Pg. 274)

TYPICAL APPLICATIONS

• Offices

• Corridors

• Retail

• Hospitality

KEY SELECTION ATTRIBUTES

• Upgrade look at a modest price

• Ceiling-2-Ceiling™ Post-consumer Recycled Content options: Items

1773HRC, 1774HRC, 1775HRC,

1776HRC, 1777HRC

(check armstrong.com/greengenie)

• USDA Certified Biobased Product – 100%

• Durable – Scratch-resistant

• Non-directional visual reduces scrap and installation time

• 30-Year Limited System Warranty against visible sag (excludes items 1796 and 1798), mold and mildew

COLOR

White

This durable, fine-textured panel offers a non-directional visual.

TechLineSM 877 ARMSTRONG armstrong.com/commceilings

DETAILS (Other Suspension Systems compatible. Refer to listing on page 180.)

1. Dune™ Tegular

2. Dune™ Square Lay-in with Prelude 15/16" suspension system

3. Dune™ Tegular with Suprafine® 9/16" suspension system

4. Dune™ Tegular with Silhouette® XL® 9/16" suspension system with 1/4" reveal

5. Dune™ Tegular with Interlude® XL® HRC 9/16" suspension system 1 2 3 4 5

1772, 1773, 1774, 1775, 1776 bowmanar Text Box

DUNE™

Square Lay-in & Tegular fine texture

VISUAL SELECTION PERFORMANCE SELECTION Dots represent high level of performance.

30-Year Performance Guarantee & Warranty When installed with Armstrong® Suspension System.

Details at armstrong.com/warranty (Excludes items 1796, 1798, and large other size panels)

Weight; Square Feet/Carton 1772 – 0.94 lbs/SF; 64 SF/ctn 1773 – 0.88 lbs/SF; 64 SF/ctn 1796 – 1.33 lbs/SF; 67 SF/ctn 1798 – 1.14 lbs/SF; 50 SF/ctn 1850 – 1.19 lbs/SF; 48 SF/ctn 1851 – 1.22 lbs/SF; 64 SF/ctn 1774, 1775 – 0.75 lbs/SF; 64 SF/ctn 1776, 1777 – 0.75 lbs/SF; 64 SF/ctn 1852, 1853 – 1.20 lbs/SF; 48 SF/ctn

Minimum Order Quantity 1 carton, excludes other size panels

Metric Items Available 1772M, 1850M, 1773M, 1851M, 1796M, 1798M, 1775M, 1777M – Metric items are subject to extended lead times and minimum quantities.

Contact your representative for more details.

PHYSICAL DATA

Material Wet-formed mineral fiber

Surface Finish Factory-applied latex paint

Fire Performance ASTM E84 and CAN/ULC S102 surface burning characteristics. Flame Spread Index 25 or less.

Smoke Developed Index 50 or less (UL labeled.)

Fire Guard: A fire-resistive ceiling when used in applicable UL assemblies

ASTM E1264 Classification Type III, Form 2, Pattern C E Fire Class A

Humidity/Sag Resistance HumiGuard® Plus ceiling panels maintain superior sag resistance. Recommended for areas subject to high humidity, up to, but not including, standing water and outdoor applications. Excludes items 1796, 1798, and large other size panels.

Anti-Mold/Mildew Ceiling panels with BioBlock® coating contain a mold-inhibiting agent that resists the growth of mold and mildew.

VOC Emissions Third-party certified compliant with California Department of Public Health CDPH/EHLB/Standard Method Version 1.1, 2010. This standard is the guideline for low emissions in LEED, CalGreen Title 24, ANSI/ASHRAE/USGBC/IES Standard 189; ANSI/GBI Green Building Assessment Protocol.

Primary (Embodied) Energy See all LCA information on our EPD’s.

High Recycled Content Contains greater than 50% total recycled content.

Total recycled content based on product composition of post-consumer and pre-consumer (post-industrial) recycled content per FTC guidelines.

Insulation Value R Factor – 1.6 (BTU units) R Factor – 0.28 (Watts units)

100%

Edge Profile

Susp. Dwg.

Pgs. 295-299 armstrong.com/ catdwgs

Item No.

Dimensions (Inches)

UL Classified

Acoustics

To ta l Ac ou st ic s1

Fi re

Ra tin g

Li gh t Re fle ct

An ti-

M ol d

M ild ew

Sa g

Re si st

Ce rt ifi ed

L ow

VO

C Em is si on s

Sc ra tc h

Re cy cl ed

Co nt en t

Re cy cl e

Pr og ra m

-Y r W ar ra nt y

NRC + =

DUNE™ Square Lay-in Bio-

Block Humi-

Guard+ Durability

15/16" Square Lay-in

1 1772 24 x 24 x 5/8" 0.50 30 – Class A

0.83

• • • • Std • •

1 1850 24 x 24 x 5/8" 0.50 35

– Fire

Guard™

0.83

• • • • Std • •

1 1773

1773HRC

24 x 48 x 5/8" 0.50 30 – Class A

0.83

• • • • Std • •

1 1851 24 x 48 x 5/8" 0.50 35

– Fire

Guard 0.83

• • • • Std • •

1 1796 20 x 60 x 3/4" 0.50 35

– Class

A 0.83

• Std • • • • 1-Yr

1 1798 30 x 30 x 3/4" 0.50 35

– Class

A 0.83

• Std • • • • 1-Yr

1 Other Size Panels

W: 12" – 30" / L: 18" – 72" 5/8" or 3/4" Thick

N/A N/A – Class A

0.83

• Std • • Std • 1-Yr

DUNE Tegular

15/16" Angled Tegular

12 1774

1774HRC

24 x 24 x 5/8" 24 x 24 x 5/8"

0.50 35

– Class

A 0.83

• • • • Std

12 1853 24 x 24 x 5/8" 0.50 35

– Fire

Guard 0.83

• • • • Std • •

12 1776

1776HRC

24 x 48 x 5/8" 24 x 48 x 5/8"

0.50 35

– Class

A 0.83

• • • • Std

12 Other Size Panels

W: 12" – 30" / L: 18" – 72" 5/8" Thick

N/A N/A – Class A

0.83

• Std • • Std • 1-Yr

9/16" Beveled Tegular

29, 44, 48, 52, 56, 60

1775HRC

24 x 24 x 5/8" 24 x 24 x 5/8"

0.50 35*

– Class A

0.83

• • • • Std

29, 44, 48, 52, 56, 60

1852 24 x 24 x 5/8" 0.50 35

– Fire

Guard 0.83

• • • • Std • •

29, 44, 48, 52, 56, 60

1777HRC

24 x 48 x 5/8" 24 x 48 x 5/8"

0.50 35

– Class

A 0.83

• • • • Std

29, 44, 48, 52, 56, 60

Other Size Panels

W: 12" – 30" / L: 18" – 72" 5/8" Thick

N/A N/A – Class A

0.83

• Std • • Std • 1-Yr

1 Total Acoustics™ ceiling panels have an ideal combination of noise reduction and sound-blocking performance in one product.

SUSPENSION SYSTEMS

15/16" 9/16"

Prelude®

Prelude XL® Fire Guard

Silhouette 1/4" Reveal

Silhouette® 1/8" Reveal

Suprafine®

Suprafine® XL® Fire Guard™

Interlude® Sonata® Trimlok®

* CAC reduced two points on these suspension systems

HRC items contain 15% or greater post-consumer recycled ceilings

LOCATION DEPENDENT

RECYCLED

CONTENT

LEED®

e n e rg y m a n a g e m e n t re c y c la b le e x te n d p ro d u c e r re s p m a te ri a l in re d ie n t re p o rt in g re c y c le c o n te n t s o u rc in g f ra w m a te ri a ls lo w e m it ti n g m a te ri a ls li g h ti q u a li ty b io b a s m te ri a ls re g io n a l m a te ri a ls d e s ig n f o r fl e x ib il it y c o n s tr u c ti w s te m g m t

E P

D a c o u s ti c s

Calculate LEED contribution at armstrong.com/greengenie56%U

P T

O

LEED® is a registered trademark of the U.S. Green Building Council All other trademarks used herein are the property of AWI Licensing Company and/or its affiliates © 2015 AWI Licensing Company Printed in the United States of America

TechLineSM / 1 877 ARMSTRONG armstrong.com/commceilings

(search: dune)

M

IN

E R

A L

F

IB

E R

BPCS-4351-715

bowmanar

ACT-1 (CONT.)

bowmanar

CPT-1

Field Tile fl oo r w al l c ou nt er to p

COLORBODY™ PORCELAINFLORENZA™

SABBIA FZ01

BRUN FZ03

OLIVA FZ02

AZZURRO FZ04

Cover photo features Azzurro 18 x 18 field tile in a diamond pattern on the floor bowmanar

PT-1, PT-2, PTB-1

SABBIA/BRUN ACCENT FZ10

OLIVA/AZZURRO ACCENT FZ11

Pattern Ideas

Decorative Accents

COLORBODY™ PORCELAINFLORENZA™

MODULAR RECTANGLE GRID PATTERN GRID WITH ACCENT DIAMOND PATTERN

CREATIVE IDEAS

A cc en t

C ol or

SABBIA FZ01 BRUN FZ03

ADIGE WARM BLEND DA81

NATURAL STONE

3 x 1 Decorative Accent

STONEGATE DA75

NATURAL STONE

2 x 12 Accent

OLIVA FZ02 AZZURRO FZ04

SMOKY TOPAZ CR51

CRISTALLO GLASS

1 x 8 Rope Accent

ALTURAS BLUE F007

FASHION ACCENTS

3 x 12 Accent bowmanar Text Box

(CONT.)

SIZES

SQ.FT.

CARTON

PCS. PER

CARTON

24 x 24 Field Tile (23-1/2" x 23-1/2") (59.8 cm x 59.8 cm) 15.50 4

18 x 18 Field Tile (17-5/8" x 17-5/8") (44.8 cm x 44.8 cm) 13.08 6

12 x 24 Field Tile (11-3/4" x 23-1/2") (29.8 cm x 59.8 cm) 11.62 6

12 x 12 Field Tile (11-3/4" x 11-3/4") (29.8 cm x 29.8 cm) 11.62 12

3 x 12 Field Tile (2-3/4" x 11-3/4") (6.9 cm x 29.8 cm) -- 10

COMMERCIAL USAGE

INTERIOR EXTERIOR

RESIDENTIAL

LIGHT

COMMERCIAL

RESIDENTIAL

Floors/Patios

Walls/Backsplashes

Countertops

Pool Decking

Pool Linings

Suitable for exterior walls in freezing and non-freezing climates when proper installation methods are followed.

TRIM

TYPE NUMBER SIZE PCS. PER

CARTON

Bullnose S-43C9 3 x 12 30

Cove Base* S-36C9T 6 x 12 30

Cove Base Outcorner SC-36C9T 1 x 6 15

* Cove Base trim is intended to coordinate with floor field tile in the standard 90-degree installation position.

RESIDENTIAL USAGE

FLOORS

WALLS

COUNTERTOPS

EXTERIOR

PATIOS

EXTERIOR POOL

DECKS

F W C EP ED

SHADE VARIATION

RANDOM (V4)

Extreme color and texture variation from tile to tile and within each tile;

a random look.

NOTES

Water, oil, grease, etc. create slippery conditions. Floor applications with exposure to these conditions require extra caution in product selection. Not for use on ramps.

For additional information, refer to “Factors to Consider” at http://daltile.com/factors-to-consider.cfm.

Since there is shade variation in all natural products, the tile and trim supplied for your particular installation may not match these samples. Final selection should be made from actual tiles and trim and not from tile and trim samples or color reproductions.

Manufactured in accordance with ANSI A137.1 standards.

Strong random shading is a part of the natural beauty of this product. To achieve the maximum intended results, tile should be pulled from multiple cartons and placement decided upon prior to installation.

Special care should be taken when grouting with dark pigmented colors. A grout release is recommended to prevent finely powdered pigments from lodging in the pores of the surface. Use of a latex modified thin-set is recommended for installation.

Special consideration needs to be given when installing tiles 20” and larger. Please refer to www.daltile.com/LargeTiles for more information.

INSTALLATION

THICKNESS GROUT JOINT RECOMMENDATION

5/16" 1/8" (3/16" when rectangular sizes are used in a staggered brick-joint pattern, where the overlap does not exceed 33%)

TEST RESULTS

ASTM# RESULT

Water Absorption C373 < 0.5%

Breaking Strength C648 > 450 lbs

Scratch Hardness MOHS 8.0

Chemical Resistance C650 Resistant

Dynamic C.O.F. A137.1 ≥ 0.42

Static C.O.F. C1028 Wet: ≥ 0.60 Dry: ≥ 0.70

Dynamic C.O.F. (Wet) value as measured by the DCOF AcuTest™ helps to assess a products suitability for a commercial environment. For more information, visit our website at www.daltile.com/DCOF.

DYNAMIC C.O.F. (WET) : 2

The higher the rating, the higher the slip resistance.

1 < .42

2 ≥ .42

STATIC C.O.F. (WET) : 3

1 < .50

2 .50 - .59

3 ≥ .60 bowmanar Text Box

Urethane Grout Technical Data Sheet

S T A R Q U A R T Z I N D U S T R I E S , I N C . • 1 3 0 0 R U S S E L L S T R E E T • B A L T I M O R E , M D • 2 1 2 3 0 P H O N E : 8 6 6 - 2 2 0 - 4 5 0 0 • F A X : 8 6 6 - 2 2 0 - 4 7 0 0 • W W W . S T A R Q U A R T Z . C O M

PRODUCT DESCRIPTION

QuartzLock™ 2 Grout is a PRE MIXED, READY TO USE URETHANE and colored quartz based grout for ceramic, porcelain, glass and natural stone tiles on floors and walls.

QuartzLock Grout requires no sealing and is resistant to typical food stains and most household chemical products.

FEATURES AND BENEFITS

Pre mixed, ready to use Excellent chemical, stain and mildew resistance Semi flexible, low shrinkage and high crack resistance No color fading, streaking or shading – Even when wet!

Fast and easy clean up when compared to epoxy and cement grouts Excess product can be saved and used later UV stable colors (non yellowing) Self sealing – no sealing required Non sag formula great for vertical surfaces Free of BPA (bisphenol A) found in epoxy grouts Dust free mixing Fast, easy installation – installs up to 50% faster than other grouts Superior to cement grout Contributes to USGBC LEED Credits: MR 4.1 & 4.2 (Recycled Content), MR 5.1 & 5.2 (Regional Materials), and EQ, 4.1 (Low Emitting Materials).

PRODUCT USES

QuartzLock Grout can be used in grout joint widths from 1/16” to 1/2” on vertical or horizontal surfaces in both interior and exterior installations of ceramic, porcelain, glass and natural stone tiles.

INSTALLATION

Read and understand Technical Data Sheet and Material Safety Data Sheet completely before beginning installation.

Follow applicable ANSI, TCNA and NTCA installation standards. Always do a test area to ensure product satisfaction, including adhesion to substrate, and/or to become familiar with proper application techniques prior to use.

QuartzLock Grout is a READY TO USE Urethane Grout and different installation techniques are required for successful product use. Please read the following instructions carefully.

Preparation for Grouting:

DO NOT add any water, liquid, or other material to QuartzLock Grout! This will cause grout failure and void all warranties.

A milky, white liquid may be present on the surface of the grout when opened. This is from normal settling during shipment. The use of a margin trowel is recommended to bring grout into suspension. If a drill mixer is used, mix at low speed for no more than 30 seconds. Over mixing with a drill mixer may introduce excessive air into the product and cause grout sagging on vertical applications and/or other performance issues. Continue to mix with a margin trowel throughout the grouting process.

Ensure tile is firmly set and mortar is completely dry (always follow manufacturer’s instructions) before grouting. Remove all spacers, water, debris and adhesive from tile joints.

For best results, surface of tile should be at room temperature (70°F to 75°F). Urethane materials are affected by temperature and humidity variations. Cool temperatures and/or high humidity will slow cure time.

To facilitate cleaning, pre seal all porous tile and natural stone before grouting.

For glass tile, polished marble, stone and other soft surfaces, test grout on a small area to ensure compatibility.

Make sure grout joints are clean, dry, and free from solvents and residue before grouting.

Application:

Spread grout using a green, sharp edged, firm rubber grout float. Work the grout diagonally across the joints, packing them full.

Remove excess grout from the tile surface, pulling the edge of the float diagonally across the joint to prevent grout removal.

Grout Cleaning:

For best results, remove grout haze AS YOU WORK, particularly in warm or dry climates. If working alone, only grout as far as you can reach (10 12 square foot area) before initial cleaning. If working as a team, one person should grout, with the other(s) cleaning immediately behind the first person.

Rinse sponge in water and wring out completely. Since urethane grout requires very little water during cleanup, make sure that the sponge is wrung nearly dry. Wipe lightly, leaving sponge flat on the tile surface to prevent grout removal from joints. Excessive water during cleanup bowmanar

S T A R Q U A R T Z I N D U S T R I E S , I N C . • 1 3 0 0 R U S S E L L S T R E E T • B A L T I M O R E , M D • 2 1 2 3 0 P H O N E : 8 6 6 - 2 2 0 - 4 5 0 0 • F A X : 8 6 6 - 2 2 0 - 4 7 0 0 • W W W . S T A R Q U A R T Z . C O M can dilute the urethane binder and cause curing issues that may lead to grout failure.

Wipe up spilled water immediately. Do not allow water to sit on grout surface or in ungrouted joints.

Change water mixture after each 100 square feet, for each new bucket of grout, or when dirty.

Check work as you clean. Repair any low spots with additional grout. Unlike other grouts, DO NOT over wash.

Allow cleaned areas to dry, and then inspect tile / stone surface. If a second cleaning is necessary, wait 24 hours and spray a film remover (Aqua Mix® Heavy Duty Tile and Grout Cleaner, Miracle Tile & Stone Cleaner, or DuPont™ StoneTech® Professional KlenzAll™ Cleaner) on a white scrubby Doodlebug™ cleaning pad, rubbing the tile lightly to remove any remaining urethane haze, then using a damp sponge and clean water, wipe the surface to remove the film remover (do not flood surface with cleaner).

Finish by drying the tile surface with a clean towel or cloth. Contact StarQuartz if persistent haze exists.

Installation Requirements

For use in joints 1/16” or greater. Ensure that joints are well packed. Smaller joints may require extra effort.

To speed up installation, or for quarry and other porous tile and/or outdoor applications, pre wet tile surface using clean water with a damp sponge prior to spreading grout, being careful not to leave standing water in the grout joints.

Maintain temperature above 40°F (5°C) during installation and curing.

CURING

Protect finished surface from light traffic for at least 24 hours at 70°F (21°C). Heavy foot traffic requires 72 hours at 70°F and 50% relative humidity. See Limitations/Cautions below for further curing requirements.

If needed, cover ONLY with kraft or breathable paper after initial 24 hour curing period.

Full cure depends on grout depth. Normal cure of a ¼” grout joint with a 3/8” thick tile is 28 days.

SHOWERS / STEAM SHOWERS / WET APPLICATIONS

Use an approved waterproof sealer for mud bed applications and follow manufacturer’s recommendations for sealer installation. For liquid applied waterproofing materials, apply to within 1” of any drains to prevent weep hole blockage. The use of pre sloped, waterproof trays (instead of mud beds) is highly recommended.

Shower, steam shower, pool, fountain and wet area installations must be protected from moisture and allowed to cure for 7 days before use.

LIMITATIONS/CAUTIONS

Do not apply or clean up this product like traditional cement based or epoxy grouts; QuartzLock Grout is a new technology that requires a simpler and easier application and clean up process.

Follow all manufacturers’ instructions for all other setting materials, waterproofing, anti fracture membranes, etc. to be used on the job.

Minimum recommended grout joint width is 1/16”.

Maximum recommended grout joint width is 1/2”.

Ensure that grout joints are fully packed, especially in tight and irregular joints. Take special care in all wet and outdoor applications.

Do not use as a setting mortar.

Not for use in heavy industrial applications (i.e. chemical plants), in areas subjected to harsh or persistent chemicals, or areas exposed to very aggressive cleaning routines such as steam or pressure washing.

QuartzLock Grout is not a replacement for a waterproofing membrane. When a waterproofing system solution is required, please contact StarQuartz Technical Service.

Protect grout from staining agents and chemicals during the cure process.

Grouting when tile surface is above 90°F (32°C) is not recommended. Cool tile surface with damp sponge if tile surface is above 90°F (32°C). Be careful not to add excessive water during the tile cooling process.

Do not use vinegar or acid solutions for clean up; this could damage uncured grout.

Always use protective clothing (gloves and eye protection) when working with grout.

Prior to regrouting applications, remove 1/8” of old grout and any surface contaminants. Be sure to rinse any residual solvent/cleaner off grout joints, then allow joints to completely dry before re grouting.

Do not use for commercial or wet environment re grouting installations, including showers, steam showers, and outdoor applications.

Seal porous tile surfaces with a water based sealer, including the sides of the stone, prior to grouting with QuartzLock Grout.

Outdoor installations must be protected from moisture (rain) for 7 days. If rain is forecast within 7 days, protect by tenting the grouted area (at least 1 foot above surface).

Not for use in hot tubs.

bowmanar

GT-1 (CONT.)

S T A R Q U A R T Z I N D U S T R I E S , I N C . • 1 3 0 0 R U S S E L L S T R E E T • B A L T I M O R E , M D • 2 1 2 3 0 P H O N E : 8 6 6 - 2 2 0 - 4 5 0 0 • F A X : 8 6 6 - 2 2 0 - 4 7 0 0 • W W W . S T A R Q U A R T Z . C O M

Wait 7 days before rigorously cleaning tile and grout surface.

Wait 7 days prior to exposing grout to full submersion.

Use care on soft, highly polished surfaces to avoid scratching. Test a small area. Use of a sealer is always recommended on polished marble, stone, slate and other natural, porous tiles.

Use of enzymatic floor cleaners will void all warranties.

Do not ingest. Keep out of the reach of children.

Do not use StarCure® Urethane Grout Cure Accelerator.

Do not use solvent based adhesives or sealers with QuartzLock Grout.

Protect grout from freezing. Do not grout outdoors or in unheated areas when temperatures are expected to be below 40°F (5°C) within 3 days. If product freezes, return to room temperature and use as directed.

For Chemical Emergency, call CHEMTREC 24 hours, (800) 424 9300 in North America, (703) 527 3887 International (collect).

For more information, consult the MSDS for this product.

AVAILABILITY AND COST

QuartzLock Grout is available at better distributors throughout the U.S. and Canada. Contact your local distributor or StarQuartz Industries, Inc. at (866) 220 4500 or info@StarQuartz.com.

MAINTENANCE

QuartzLock Grout requires occasional cleaning with water and common grout cleaners. For best stain resistance, always clean up spills immediately.

SHELF LIFE

QuartzLock Grout is guaranteed to remain suitable for use up to a period of two (2) years if stored unopened at temperatures between 32 F (0 C) and 100 F (38 C) . After opening, QuartzLock can be saved for reuse if properly resealed in original container (always wipe the pail lip clean prior to resealing to ensure proper seal is achieved with the Vapor Lock lid). If product freezes, return to room temperature, mix well, and use as directed.

PACKAGING

Available in 9 lb. and 18 lb. units

WARRANTY

Visit to www.StarQuartz.com to see our complete warranty.

APPLICABLE STANDARD

QuartzLock Grout is a revolutionary new technology which employs state of the art urethane chemistry. As yet, there is no current ANSI or ASTM standard for this technology (ANSI 118.3 pertains only to epoxy grout products);

however, for comparative purposes, physical and chemical properties are listed in the table below. Epoxy grouts are hard, brittle and lack flexibility. QuartzLock Grout is designed to have the perfect balance of physical properties in order to provide flexibility, strength and adhesion to a variety of materials, making it the best choice for a wide variety of applications. Specifications are subject to change without notice.

Typical Properties

Description Typical Results

Water Cleanability Pass Initial Set >2 hrs.

Service Strength Pass Vertical joint sag Pass

ASTM C267 Chemical Pass Compressive strength >3,500 psi

Linear Shrinkage 0.06% Water absorption <1%

Open Time 180 minutes Color 40 available

Results shown are typical and reflect test procedures used by the Tile Council of North America (TCNA) for ANSI 118.3 and 118.3 modified.

Actual field performance will depend on installation methods, site conditions and other environmental factors.

Working Properties

Description Time

Required* Working Time 3 hrs Tack Free Time 8 hrs Ready for light foot traffic 24 hrs Ready for heavy foot traffic 72 hrs Stain resistant (food, cleaners, etc.) 3 days Showers, Outdoors, Pools, Fountains and Wet Area Installations

7 days

* Results are typical, but reflect testing procedures employed. Actual results may vary due to particular environmental conditions and other factors (e.g.

type of setting material used).

bowmanar

S T A R Q U A R T Z I N D U S T R I E S , I N C . • 1 3 0 0 R U S S E L L S T R E E T • B A L T I M O R E , M D • 2 1 2 3 0 P H O N E : 8 6 6 - 2 2 0 - 4 5 0 0 • F A X : 8 6 6 - 2 2 0 - 4 7 0 0 • W W W . S T A R Q U A R T Z . C O M

COVERAGE CHART (SQ. FT)

18 lb. Unit

Tile Size Joint Width

(inches) 1/16" 1/8" 3/16" 1/4" 3/8" 1/2"

1" x 1" x 1/4" 63 32

2" x 2" x 1/4" 126 63

4 1/4" x 4 1/4" x 5/16" 214 107 71 54 36 27

4" x 8" x 1/2" 168 84 56 42 28 21

6" x 6" x 1/2" 189 95 63 47 32 24

8" x 8" x 3/8" 337 168 112 84 56 42

12" x 12" x 3/8" 505 253 168 126 84 63

13" x 13" x 3/8" 547 274 182 137 91 68

16" x 16" x 3/8" 673 337 224 168 112 84

18" x 18" x 3/8" 758 379 253 189 126 95

24" x 24" x 3/8" 1010 505 337 253 168 126

9 lb. Unit

Tile Size Joint Width

(inches) 1/16" 1/8" 3/16" 1/4" 3/8" 1/2"

1" x 1" x 1/4" 32 16

2" x 2" x 1/4" 63 32

4 1/4" x 4 1/4" x 5/16" 107 54 36 27 18 13

4" x 8" x 1/2" 84 42 28 21 14 11

6" x 6" x 1/2" 95 47 32 24 16 12

8" x 8" x 3/8" 168 84 56 42 28 21

12" x 12" x 3/8" 253 126 84 63 42 32

13" x 13" x 3/8" 274 137 91 68 46 34

16" x 16" x 3/8" 337 168 112 84 56 42

18" x 18" x 3/8" 379 189 126 95 63 47

24" x 24" x 3/8" 505 253 168 126 84 63 bowmanar

ProductProductProductProduct datadatadatadata sheetsheetsheetsheet

FlFlFlFluguguguggergergerger FlutexFlutexFlutexFlutex 5555

ProductProductProductProduct propertiespropertiespropertiesproperties

Matt, robust acrylic paint with optimum opacity. Provides a well-cured and washable surface. Withstands ordinary cleaning, where the entire surface is cleaned. Easy to apply and to repaint.

Flutex 5 is labelled with the European ECO label:

Flutex 5 in coloured shades has a slightly higher gloss level than the white and may come off during the first application phase due to a surplus of pigments. Does not block for strike-through of aqueous colorants, water blotches or nicotine.

· Optimum opacity

· Easy and quick to repaint

· Great spreading capacity

ApplicationApplicationApplicationApplication

For interior use on ceilings and walls in living-rooms, common rooms and offices, as well as exterior on mineral facades of cement render and concrete. Perfect for restoration tasks on previously treated surfaces.

TreatmentTreatmentTreatmentTreatment

The substrate must be clean, dry and solid. Clean with Fluren 37 Basic Cleaner prior to paint treatment. Interior use: Prime slightly chalking or absorbent interior substrates with Flugger Sealer. If there is any risk of strike-through from aqueous colorants, water blotches or nicotine, prime with Fugger Iso Primer

& Finish. Exterior use: Prime with Flugger Facade Primer. NB! Exterior use: Add

Flugger Additive 100. Apply 1-2 coats, by paint brush by paint roller or by bowmanar

P-1 - P-5 spraying. Depending on the substrate, the appli-cation method and the temperature, dilution with up to 10 % water is possible.

FlutexFlutexFlutexFlutex 5555 inininin 120120120120 litrelitrelitrelitre packagingpackagingpackagingpackaging

At low temperatures, the product thickens and becomes difficult to pump.

Therefore, it is important that the product is stored in a tempered environment

(approximately 20 ). Choice of nozzle when using Graco spraying unit Ultramax

695, 795, 1095, or Mark V: We recommend nozzle no. 517, 519 alternatively 521 for big projects.

GoodGoodGoodGood practicepracticepracticepractice

Matt surfaces are not suitable for walls in institutions, corridors or other places, where the surface is exposed to heavy smudging and/or wear and tear.

TechnicalTechnicalTechnicalTechnical datadatadatadata ---- whitewhitewhitewhite

Type: Acrylic paint

Specific gravity: 1,45 kg/litre

Gloss: 5, matt

Solids: Weight%: 60 Vol.%: 40

Spreading rate: 7-9 m2 per l. 4-5 m?per l when sprayed

Application temp.: Min. work. temp. during drying/curing:+5

Max atmospheric humidity 80 % RH

Drying time at 20, 60 % RH: Dry to touch: 1 h

Recoat interval: 2 h

Fully cured: Several days

Washability: Class 2, according to EN 13300

Density: Water vapour permeability: Sd= 0.18m equal to class 2, according to EN 7783-2

Dilution: Water

Cleaning of tools etc.: Water and soap

Storage: Cool, frost-free and tightly closed

Key:FLUTEX 5 April 2013, replaces February 2012

Always make sure, that the product data sheet is the latest edition.

Please also refer to the information on the label as well as to the Application Guide at www.flugger.dk

All information is based on the existing legislation, laboratory tests and practical experience.

Contact: produktsupportdk@flugger.com phone. +45 76 30 33 80.

bowmanar

P-1 - P-5 (CONT.)

11/10/2015 Flügger data blade http://gm.flugger.com/NO/prodsikk.dll?SPROD=ON&SPROD-NR=FLUTEX+20S&GO=Vis+udskrift 1/2

Product Datasheet Flügger Flutex 20S

Product Features

Rich, acrylic reinforced PVA paint with a semi-matt surface. Fremstår uniform in gloss, no matter what angle the surface seen in. Flutex 20S labeled with the EU Flower.

SV /

07/02

- Suitable for indoor use

- Limited use of hazardous substances

- Low content of solvents

Prohibits not against penetration of water-soluble dyes, water stains, nicotine

· Rich and semi-matt with neat finish

· Great and consistent results from ale angles Application

Used indoors for walls in eg living or alleys.

Is particularly useful on plaster, concrete, panels and the glass fabric and fiber felts where the product gives a rich appearance.

Treatment

The surface should be clean, dry and sustainable. Cleaning before painting treatment undertaken with Fluren 37 Gross Rent. Light infectious or absorbent substrates with Flugger Anchoring Ground.

At the risk of penetration of water-soluble dyes, water stains or nicotine, primed with Flügger Iso Primer and Finish. Applied by brush, roller or spray.

Flügger Flutex 20S in 120 l. Packaging

At low temperatures, the product will thicken and difficult to pump. It is therefore important that the storage takes place in temperate environment (approximately 20 ° C). Choice of nozzle using Graco spray equipment: Ultramax 695, 795, 1095 or Mark V: Recommended nozzle no. 517, 519, alternatively 521 to major tasks.

Cleaning and Maintenance

Flutex 20S withstand wiping with a damp cloth. Use eg. Fluren 32 Universal Interest.

Stain any damages and scratches with the same paint originally used.

Technical data

Type: Acrylic Reinforced PVA paint Curb weight: 1.4 kg / liter Gloss: 20, Semi Matt Solids: 60 wt%, 44 vol% Consumption: 7-9 m² per. liter, depending on substrate roughness.

Application temperature: Min. working temp. during application, drying and curing: + 5 ° C Max. humidity 80% RH Drying at 20 ° C, 60% RH Dust: 1 hour Recoatable: 6 hours Fully cured: Several days Total issue: ref. EN16000 9: 2006: <10 mcg / m2h after 28 days Washability: Class 2, according to EN 13300 Dilution: Water Cleaning tools: Water and soap Storage: Cool, frost-free and in dense packaging bowmanar

11/10/2015 Flügger data blade http://gm.flugger.com/NO/prodsikk.dll?SPROD=ON&SPROD-NR=FLUTEX+20S&GO=Vis+udskrift 2/2

Environment and Safety: See MSDS In certain environments can Heksesot occur, to minimize this, do the following:

Ventilate well during and after renovation, warm up the apartment up to 28c ° when furniture, furnishings and everything new is in the house, air as well, this is done 2 times. Ventilate well 2-3 times a month the first year, Limit the use of open fireplace and old wood stoves, do not use stearic / scented candles the first year.

Key: FLUTEX 20S November 2014 replaces August 2012

Always check that the MSDS is the latest.

See also information on the label and possibly. Treatment manual on www.flugger.no All information is based on current legislation, laboratory tests and practical experience.

Contact: produktsupportno@flugger.com tel. +47 23 30 21 95.

http://www.flugger.no/ mailto:produktsupportno@flugger.com bowmanar

11/10/2015 Flügger Product Sheets http://gm.flugger.com/PL/prodsikk.dll?SPROD=ON&SPROD-NR=INT+HI+50&GO=Vis+udskrift 1/2

Product Information Flügger Inter ior High Finish 50

PRODUCT DESCRIPTION:

Acrylic enamel coating tough, very strong, washable with excellent aesthetic.

It will not protect against the penetration of water-soluble dyes, water and nicotine stains. Products dyed in the store may be slightly dirty in the first period of use.

Flügger Interior High Finish 50 is marked in the European eco-label.

· incredibly beautiful in semi-gloss coating

· very tough and strong

· very easy to keep clean

APPLICATION:

Interior wood when desired is hard and tough coating with a beautiful appearance, eg. Floor, doors, kitchen cabinets, paneling, furniture and protected against corrosion metal (eg. Radiators) and the inner part of the windows.

TECHNOLOGY:

Surfaces must be clean, dry, sound. Remove chalking and non-adhesive coating. The old surface thoroughly with liquid Fluren 37. New or unpainted wood primed Flügger Interior Wood Primer.

Smooth surface roughened and paint Flügger Interior Fix Primer. Metal secure the appropriate soil corrosion.

Apply by brush, roller, spray, preferably two layers. When painting spraying do not dilute.

CLEANING AND RENOVATION:

If necessary, the surface of the wash water with Flurenu 32. The renovation is carried out the same, which were painted before.

ADDITIONAL RECOMMENDATIONS:

Until the completion of the painting and curing of the coating must be handled gently with a painted object.

TECHNICAL DATA (for white):

Product Type: Dispersion acrylic enamel Gloss: 50 semigloss Density: 1,30 kg / l Solids content: wt%. - 48% vol. - 38 Capacity: approx. 8-10 m2 / l Temperature painting: min. + 5 ° C, max humidity. 80% Also during the drying and curing Drying time at 20 ° C, 60% RH .: dry to the touch 1 h next painting 6 h at lower temperature and / or higher humidity drying time is extended completely cured - a few days Total emissions: <10 g / m 2 h after 28 days, the PN-EN ISO 16000-9: 2009 Dilution: water / spray during painting do not dilute Cleaning tools: water with detergent Storage: in a cool frost free room.

in an airtight container.

See also the information on the label and the procedures for www.flugger.com http://www.flugger.com/ bowmanar

11/10/2015 Flügger Product Sheets http://gm.flugger.com/PL/prodsikk.dll?SPROD=ON&SPROD-NR=INT+HI+50&GO=Vis+udskrift 2/2

Key: INT HI 50 November 2012, replaces the card with August 2012

Flügger Sp. z oo Rocket 20 A, 80-298 Gdansk; tel. +48 58 340 28 00 www.flugger.pl Make sure that the information is up to date edition. Product features may vary with technical development. The information provided is based on current law, laboratory testing and practical experience.

bowmanar

Product data sheet Flügger Glass Tissue (Flügger glasvæv)

Product description

Type: Woven glass tissue, starched.

Flügger woven glass is starched woven glass tissue particularly manufactured to be painted.

Woven Glass Tissue has a decorative effect on the wall and counteracts formation of cracks.

Product application

Suitable as wall covering on concrete, plaster, gypsum boards etc.

The surface must be clean, dry, even and solid. Slightly chalking or absorbent surfaces must be primed with Flügger Sealer, water-based. Hanging on old woven glass may cause an unintended pattern, and it is therefore recommended with full filling to even surface.

Adhesive: See product description of Flügger Adhesives.

Hanging: Edge to edge.

Painting: First coat should be Flügger Priming Paint for Woven Glass Tissue.

As top-coat all types of wall paint in desired gloss and colour.

The woven glass designs have been approved in Fire Class 1 acc. to SBN 1980 (Nordtest) when hung with PVA-based adhesives on concrete, light concrete etc.

or gypsum boards.

Flügger woven glass tissue 45100, 45135 and 45139 have been pre-coated. It is therefore not necessary to use Flügger Priming Paint f/Woven Glass Tissue.

Technical data

Design Weight Roll size Tensile strength kp/5 cm g/m² m vertical horizontal 44100 110 1 x 50 60 58 44135 120 1 x 50 70 25 44136 120 1 x 50 70 50 44150, 44160, 44190 150 1 x 30 60 70 44165 155 1 x 30 70 70 44170 155 1 x 30 80 80 45100 120 1 x 50 68 50 45135 130 1 x 50 70 25 45139 125 1 x 50 80 50 25322 Tissue f/wet rooms 145 0,95x25 70 25 25325 Tissue f/wet rooms 125 0.95x25 60 35 Consumption of paint: First coat:0,15-0,30 l/m2 Flwg.coats: 0,12-0,17 l/m2 The consumption depends on type of fabric, type of paint and application technique.

Key: FL GLAS May 2010, replaces January 2009

Page 1 of 2Flügger datablade

14-11-2013http://gm.flugger.com/en/PRODSIKK.DLL?PRODLIST=---FL+GLAS&amp;SPROD=ON&amp;GO4=P...

bowmanar

GFC-1, GFC-2

Always make sure, that the product data sheet is the latest edition.

Please also refer to the information on the label as well as to the Application Guide at www.flugger.dk All information is based on the existing legislation, laboratory tests and practical experience.

Contact: produktsupportdk@flugger.com phone. +45 76 30 33 80.

Page 2 of 2Flügger datablade

14-11-2013http://gm.flugger.com/en/PRODSIKK.DLL?PRODLIST=---FL+GLAS&amp;SPROD=ON&amp;GO4=P...

bowmanar

GFC-1, GFC-2 (CONT.)

PLAM-1, SM-1-SM-4 (CONT.)

Specification according EN 649 Favorite R10 PUR

St ru ct ur e

Type of flooring EN 649 Vinyl synthetic floor covering with PUR Eco System surface protection

Pattern scattered

Embossing embossed

Classification EN 685 / EN

ISO 10874

Class 23 / 34 / 43

Overall thickness EN 428 / EN

ISO 24346

2.0 mm

Sheet width EN 426 / EN

ISO 24341

183 cm

Sheet length EN 426 / EN

ISO 24341

16 - 25 m

Total weight EN 430 / EN

ISO 23997

3300 g/m²

Sa fe ty C rit er ia

Flammability EN 13501-1 Bfl - s1, adhered according to certificate, see www.dlw.eu

Slip resistance ASR A1.5 /

BGR 181

R10

Slip resistance in barefoot areas List NB Class A

Dynamic coefficient of friction EN 13893 DS (> 0.30)

REACH Regulation No. 1907/2006 Article 33 contains no substances mentioned in the SVHC-list

Pe rfo rm an ce

Impact sound reduction EN ISO 10140 3 dB

Residual indentation EN 433 / EN

ISO 24343

app. 0.04 mm

Wear group vinyl wear layer EN 649 P

Colour fastness ISO 105-B02 ≧ rating 6

Vertical resistance R₁ EN 1081 -

Surface resistance EN 1081

Electrical insulation to ground VDE 0100 > 200 kOhm

Static electrical charge EN 1815 ≦ 2.0 kV

Thermal resistance EN 12667 0.010 m² K / W

Thermal conductivity EN 12524 0.25 W / m K

Resistance against chemicals EN 423 / EN

ISO 26987

good resistance against acids and alkalis even at higher concentrations

Castor chair EN 425 suitable (Type W)

Warmwater-underfloor heating suitable max. 29°C

EN 14041:2004

DOP-201

Manufactured by:

DLW Flooring GmbH Stuttgarter Straße 75 D-74321 Bietigheim-Bissingen

DLW flooring products are to be installed in full accordance with DLW Flooring installation instructions and recognised trade standards. An effective, regular cleaning and maintenance programme is vital for retaining a high appearance level. DLW flooring products should only be used as floorcoverings. Note: DLW Flooring reserve the right to amend this specification without giving prior notice. For the latest versions of the technical specifications, check our internet site: www.dlw.eu

UK 08.07.2015

bowmanar

VFC-1

D esign er Ins er t O pt io ns Enhance the beauty of the entrance system by matching Zone 3 (lobby) matting with the Foot Grille Designer Inserts in Zone 2 (vestibule). Coordinating Zone 3 matting product pages are referenced below.

Dual Track D e ep R e cess e d Sys tem roo TTrraacckkPPro TTrack SeriesS

Pro Track Series

New York Collection Premium high durability nylon fibers (6.6)Supreme Nop Aggressive and attractive polypropylene fiber

Tweed BrownSable Brown NaturalAutumn RedSpruce

SapphireBlack Walnut Midnight BlueCharcoal Dark Gray

See Page

Advanced Track D e ep R e cess e d Sys tem roo TTrraacckkPPro TTrack SeriesS

Pro Track Series

Blue Red

Charcoal Dark GrayCocoa

Charcoal Splash

Brown

See Page

Brown Sugar Cocoa Butter

Light Gray

ACCESSORIES

FOOT GRILLESENTRANCE SYSTEMS & MAT TING

bowmanar

Depth VV or AD Frame (New Construction)

TT Overlap Frame (Retrofits)

Grille Only 1-1/2" 1-1/2"

Grille & Frame (Level Base) 1-5/8" 1-1/2"

Grille & Frame (Drain Pan) 2-1/2" 2-1/2"

2' Span 2'8" Span 3'6" Span

Advanced Track 3,831 2,653 1,583

Dual Track 3,831 2,653 1,583

Dri Track 1,608 1,248 1,004

Maximum Rolling Load Pounds per wheel for Level Base Installation

Features Zones

Exclusive, cross-bolt technology outlasts traditional welded key-lock construction Heaviest rolling load in the industry Anti-slip surface for indoor applications; ADA compliant Wide variety of Designer Insert Options available Custom shapes available Advanced Track and Dri Track can be radius cut Frames come pre-assembled Drain pan option available Common Uses–Entryways in office buildings, retail stores, malls, hospitals, hotels, schools, libraries

Specifications

Advanced Track Material Heavy gauge 6061-T6 aluminum with aluminum alloy 6063-T5 scraping rails and standard 100% nylon fiber drying inserts. 58.62% pre-consumer and 15.5% post-consumer recycled content. Recycled content varies with Designer Insert Options.

Dual Track Material Heavy gauge 6061-T6 aluminum with 43.97% pre-consumer and 14.12% post-consumer recycled content with standard 100% nylon drying inserts and vinyl scraper bars. Vinyl scraper bars available in black, gray and brown. Recycled content varies with Designer Insert Options.

Dri Track Material Heavy gauge 6061-T6 aluminum with standard 100% nylon fiber drying inserts. 51.84% pre-consumer and 14.86% post-consumer recycled content. Recycled content varies with Designer Insert Options.

Style Scraping and drying surface with bolted cross supports Size Custom made to your requirements. Consult our Product Specialists for assistance.

Maximum Panel Size 48" (front and back) x 42" (left to right) Multiple panels are used to construct the foot grille system

Possible LEED v 2009 Credits

MR Credit 2 (1-2 points) MR Credit 4 (1-2 points) MR Credit 5 (1-2 points) IEQ Credit 5 (1 point)

1 2 3 4 miVantage™ Heaviest rolling load in the industry with a wide selection of Designer Insert Options

Advanced Track, Dual Track and Dri Track

Dri Track D e ep R e cess e d Sys tem roo TTrraacckkPPro TTrack SeriesS

Pro Track Series

Level Base Installation Options for Advanced Track

VV EMBEDDED FRAME

1 5/8”

FINISHED

FLOOR

TT OVERLAP FRAME

1 1/2”

FINISHED

FLOOR

AD FRAME

1 5/8”

FINISHED

FLOOR

Level Base Installation Options for Dual Track

VV EMBEDDED FRAME TT OVERLAP FRAMEAD FRAME

Level Base Installation Options for Dri Track

VV EMBEDDED FRAME

1 5/8”

FINISHED

FLOOR

TT OVERLAP FRAME

1 1/2”

FINISHED

FLOOR

AD FRAME

1 5/8”

FINISHED

FLOOR

More product & color options

See Page 24 & 25

Chicago Collection™

Seattle Collection™

A C

C

ESSO

R

IES

FO

O

T G R

ILLES

EN

TR

A

N C

E SY

STEM

S & M

A T

TIN

G bowmanar

MAT-1 (CONT.)

2.4 Warranties

Effective May 2014 armstrong.com/ceilings

Thirty (30) Year Limited Ceiling Systems Warranty

Please read the following terms carefully, as they are affected by the installation conditions. Armstrong does not assume nor does it authorize any person to assume or extend on its behalf any other warranty obligation or liability. This express warranty constitutes the entire obligation of Armstrong World Industries, Inc., and there are no other warranties expressed or implied, including any warranty of merchantability or fitness for any purpose whatsoever.

Products:

ARMATUFF®, CALLA™, CERAMAGUARD® FINE FISSURED™, CIRRUS, Clean Room™ FL, Clean Room VL/VL, CREATE!™, DUNE™, DUNE Second Look®, ENDURA™, FINE FISSURED, FINE FISSURED Open Plan, FINE FISSURED Second Look, GEORGIAN™, GRAPHIS® Finetex™, GRAPHIS® Rustex™, KITCHEN ZONE™ (#673), LYRA™, MESA™, OPTIMA® Open Plan, OPTIMA Plank, OPTIMA Vector®, PAINTED NUBBY™ Open Plan, PEBBLE™, RANDOM FISSURED™, School Zone™ FINE FISSURED, SHASTA®, TUNDRA®, TechZone™, ULTIMA®, ULTIMA Open Plan, ULTIMA Vector, PRELUDE® XL, PRELUDE ML, PRELUDE XL Fire Guard™, PRELUDE PLUS XL Fire Guard, AL PRELUDE PLUS, SS PRELUDE PLUS and PRELUDE XL for Exterior Applications, SUPRAFINE® XL, SUPRAFINE ML, SUPRAFINE XL Fire Guard, 360° Painted, SILHOUETTE® XL 1/4" and 1/8" reveal, AXIOM® (all families), PRELUDE Concealed, CONCEALED Z™, Co-extruded Aluminum CLEAN ROOM™, INTERLUDE®, SONATA®, SERPENTINA® (including Serpentina Metal Infill Panels), TRIMLOK®, DRYWALL, and SHORTSPAN®.

(Applies only to products designated with the 30-Year Systems Warranty icon in the product catalog.)

Armstrong Commercial Suspension Systems and Commercial Ceiling products have a 30-year limited systems warranty when installed together and used under normal conditions. Products covered in this systems warranty are outlined above.

Ceiling panels and suspension systems are warranted to be free from defects in materials or factory workmanship for 30 years from the date of installation, except for obvious defects in materials or factory workmanship, of which Armstrong must be notified within 30 days of the date of installation.

Commercial Ceiling panels with HumiGuard® Max and HumiGuard Plus performance are warranted to be free from sagging and warping as a result of defects in materials or factory workmanship for 30 years from the date of installation.

Commercial Ceiling panels with BioBlock® Plus protection are warranted to be free from the growth of mold, mildew, and Gram-positive and Gram-negative odor and stain-causing bacteria for 30 years from the date of installation. Ceiling panels treated with BioBlock Plus on the painted surface contain a mold-inhibiting agent that provides broad-spectrum control for the growth of mold and mildew over the warranty period.