Annex_C_to_Exhibits_TechnicalPublication_Recompete.doc

N61339-XX-X-XXXX/XXXX

Date

W900KK-16-R-0005

03/18/16

ANNEX C TO EXHIBITS

(TABLE A-II, TABLE A-IV of

MIL-STD-40051-2)

CDRL C003

CDRL C009

TECHNICAL PUBLICATIONS

FOR

INTELLIGENCE AND ELECTRONIC WARFARE TACTICAL PROFICIENCY TRAINER

(IEWTPT)

U.S. Army Program Executive Office for

Simulation, Training, and Instrumentation (PEO STRI)

12350 Research Parkway

Orlando, FL 32826-3276

_1521445661.pdf

AMSC 7542 AREA TMSS

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

NOT MEASUREMENT

SENSITIVE

MIL-STD-40051-2

w/Change 1 12 May 2006

SUPERSEDING

MIL-STD-40051-2

15 October 2004

MIL-PRF-63042F(TM)

20 April 1998

DEPARTMENT OF DEFENSE

STANDARD PRACTICE

PREPARATION OF DIGITAL TECHNICAL INFORMATION

FOR

PAGE-BASED TECHNICAL MANUALS

ii

FOREWORD

1. This standard is approved for use by the Department of the Army and the Department of the Marine Corps and is available for use by all Departments and Agencies of the Department of Defense (DoD).

2. This standard establishes the technical content requirements and mandatory style and format requirements for the preparation of technical manuals (TMs) and subsequent revisions required to support the various types of equipment and weapon systems within the Department of the Army and Department of the Marine Corps. The requirements contained in this standard cover operation and maintenance at all levels through overhaul (depot), including Depot Maintenance Work Requirements (DMWRs) and National Maintenance Work Requirements (NMWRs).

3. This 2-part book form consists of the following parts.

MIL-STD-40051-1 — Preparation of Digital Technical Information for Interactive

Electronic Technical Manuals (IETM) MIL-STD-40051-2 — Preparation of Digital Technical Information for Page-

Based Technical Manuals

4. Comments, suggestions, or questions should be addressed to USAMC Logistics Support Activity, ATTN:AMXLS-AP, Redstone Arsenal, Al 35898-7466 or emailed to tmss@logsa.redstone.army.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http://assist.daps.dla.mil/online/start/.

iii

SUMMARY OF CHANGE 1 MODIFICATIONS

The following modifications to MIL-STD-40051-2 have been made:

Paragraph/Figure/Table Modification

2.2.2 Changed

3.12 Deleted

3.13 Deleted

3.34 Changed

3.37 Deleted

3.58 Deleted

3.149 Deleted

4.4 Changed

4.7.9.2 Changed

4.7.13.2 Changed

4.7.13.3 Changed

4.7.13.5 Changed

4.7.27.2.1a Changed

4.7.27.3.2 Changed

4.7.27.3.4.1 Changed

4.7.27.4.4 Changed

5.2.1.1 Changed

5.2.1.1c Changed

5.2.1.1.2 Changed

5.2.1.1.4 Changed

5.2.1.4 Changed

5.2.1.6 Changed

5.2.2 Changed

5.2.2.6 Added

6.4 Deleted

6.6 Added

Figure 12 Changed Figure 13 Changed Figure 14 Changed Figure 15 Changed Figure 16 Changed Figure 17 Changed Figure 18 Changed Figure 24 Changed Figure 25 Added Figure 26 Added A.5.1 Changed Table A-I Changed Table A-II Changed Table A-III Changed iv

Paragraph/Figure/Table Modification Table A-IV Changed Table A-V Changed Table A-X Changed Table XI Changed Table A-XII Changed Table A-XIII Changed Table A-XIV Changed Table A-XVI Added B.5.2 Changed B.5.2.4a Changed B.5.2.4c Changed B.5.2.5 Changed B.5.2.7 Changed B.5.2.9 Changed B.5.2.20 Changed B.5.4.3 Changed B.5.5.3 Changed B.5.5.4 Changed B.5.6.3 Changed B.5.6.3.1 Added B.5.6.3.2 Added C.5.2.4.6 Changed D.5.5.5.5 Changed D.5.5.8.3.6b Changed D.5.5.8.3.6c Changed D.5.5.8.4.6 Changed E.5.3.2.3.3b Changed E.5.3.4 Changed E.5.3.4.1.3b Changed E.5.3.4.1.3c Changed E.5.3.4.1.3d(2) Changed E.5.3.4.2.3.1c Changed E.5.3.5.3 Changed E.5.3.5.3.23 Changed E.5.3.9.4 Changed E.5.3.12.3 Changed E.5.3.12.4.4 Changed E.5.3.15 Changed E.5.3.15.3 Changed E.5.3.16.4 Changed E.5.3.16.5 Deleted E.5.3.16.6 Deleted E.5.3.16.7 Deleted Figure E-12 Deleted Figure E-14 Deleted v

Paragraph/Figure/Table Modification Figure E-15A Added F.5.3.5.3 (part in quotes) Changed F.5.3.6 Changed F.5.3.12.1 Changed G.5.3.1 Deleted G.5.3.1.1 Deleted G.5.3.1.2 Deleted G.5.3.1.3 Deleted G.5.3.2 Deleted G.5.3.2.1 Deleted G.5.3.2.2 Deleted G.5.3.2.3 Deleted G.5.3.3.3 (part in quotes) Changed G.5.3.3A Added G.5.3.3A.1 Added G.5.3.3A.2 Added G.5.3.3A.3 Added G.5.3.4.4 Changed G.5.3.4.4c Changed Figure G-2 Deleted Figure G-3 Deleted Figure G-4 Changed Figure G-4A Added Figure G-5 Deleted Figure G-6 Deleted Figure G-7 Changed Figure G-7A Added Figure G-8 Changed Figure G-9 Changed Appendix H Added Index Deleted

CONTENTS

PARAGRAPH PAGE

vi

FOREWORD................................................................................................................................. ii

1. SCOPE

1.1 Scope

1.2 Paragraphs with limited applicability

1.3 Use of the technical content

2. APPLICABLE DOCUMENTS

2.1 General

2.2 Government documents

2.2.1 Specifications, standards and handbooks

2.2.2 Other Government documents and publications

2.3 Non-Government publications

2.4 Order of precedence

3. DEFINITIONS

4. GENERAL REQUIREMENTS

4.1 General

4.2 Types of technical manuals

4.3 Selective application and tailoring

4.4 Preparation of digital data for electronic delivery

4.5 Use of the DTDs/Style sheets

4.6 Obtaining the DTDs/Style sheets

4.7 Style and format

4.7.1 Examples of style and format

4.7.2 TM divisions

4.7.2.1 Volume size and content

4.7.2.2 Chapters

4.7.2.3 Work packages

4.7.2.3.1 Work package size

4.7.2.3.2 Work package content

4.7.2.3.3 Development of individual work packages

4.7.3 Type size and style

4.7.4 Page size and orientation

4.7.5 Foldout pages

4.7.6 Final reproducible copy (FRC)

4.7.7 Warnings, cautions, and notes

4.7.7.1 Warning <warning>

4.7.7.2 Caution <caution>

4.7.7.3 Notes <note>

4.7.7.4 Display of warnings, cautions and notes

4.7.7.5 Icons

4.7.7.5.1 Development of icons

4.7.7.5.2 Safety warnings with icons <icon>

4.7.7.5.3 Hazardous materials warnings <warning>

vii

4.7.7.5.3.1 Format for hazardous materials warnings with icons <icon>

4.7.7.5.3.2 Abbreviated format hazardous materials warnings with icons <icon>

4.7.7.5.4 Equipment damage caution icons <icon>>

4.7.8 Chapters

4.7.8.1 Chapter title page <titlepg>

4.7.8.2 Chapter numbering

4.7.9 Work packages

4.7.9.1 Work package identification information <wpidinfo>

4.7.9.2 Initial setup information <wpinfo>

4.7.9.3 Work package sequential numbering

4.7.9.3.1 Assignment of new work packages sequence numbers for a change

4.7.9.3.2 Assignment of work package sequence numbers in volumized TMs

4.7.9.4 Work package page numbering

4.7.9.5 Work package identification number

4.7.10 Maintenance tasks and descriptive information

4.7.11 Paragraphs

4.7.11.1 Paragraph numbering

4.7.11.2 Paragraphs and subparagraph titles

4.7.11.2.1 Format

4.7.12 Procedural steps

4.7.12.1 Procedural step levels

4.7.12.2 Procedural step titles

4.7.13 Tables and lists

4.7.13.1 Table locations

4.7.13.2 Table numbering

4.7.13.3 Table titles

4.7.13.4 Table format

4.7.13.5 Standard information tables

4.7.13.6 Footnotes to tables

4.7.13.7 Tabular information

4.7.13.8 Lists

4.7.14 Placement of text

4.7.15 Placement of illustrations

4.7.15.1 Rotating illustrations

4.7.15.2 Placement of text and related illustrations for pocket TMs

4.7.15.3 Repeating illustrations

4.7.16 Margin data

4.7.16.1 Headers

4.7.16.2 Footers

4.7.16.2.1 Page numbering

4.7.16.2.1.1 Front matter

4.7.16.2.1.2 Rear matter

4.7.16.2.1.3 Blank pages

4.7.16.2.1.4 Foldout page numbers

4.7.17 Abbreviations and acronyms

viii

4.7.18 Symbols

4.7.18.1 General information for symbols

4.7.18.2 Metric symbols

4.7.19 Nuclear hardness (hardness-critical processes) marking

4.7.20 Electrostatic Discharge (ESD) sensitive marking

4.7.21 Quality Assurance (QA)

4.7.22 Security classification, emergency page and protective markings

4.7.22.1 Security classification markings

4.7.22.2 Overall security classification

4.7.22.3 Blank page backing a classified page

4.7.22.4 Emergency page markings

4.7.22.5 Protective markings

4.7.22.6 COMSEC protective markings

4.7.23 Referencing

4.7.23.1 Other documents

4.7.23.2 Government specifications and standards

4.7.23.3 Referencing within the TM

4.7.23.3.1 TM divisions

4.7.23.3.2 Volumes

4.7.23.3.3 Work packages

4.7.23.3.4 Maintenance tasks, procedures, and paragraphs

4.7.23.3.5 Tables

4.7.23.3.6 Footnotes

4.7.23.3.7 Figures and multisheet figures

4.7.23.3.8 Index numbers

4.7.23.3.9 Items on diagrams

4.7.23.4 Repeating information

4.7.23.5 Equipment, components, and parts

4.7.23.6 National Stock Numbers (NSNs) and Part Numbers (P/Ns)

4.7.23.7 Equipment panel markings (placarding)

4.7.23.8 Metric and U.S standard measurements

4.7.23.9 Temperature

4.7.24 Equations

4.7.25 Nomenclature

4.7.25.1 Nomenclature consistency and applicability

4.7.25.2 Official/approved nomenclature

4.7.25.3 Military terms

4.7.25.4 Automatic electronic test and checkout terminology

4.7.26 Comprehensibility

4.7.27 Graphics

4.7.27.1 Graphic format

4.7.27.2 Types of graphics

4.7.27.2.1 Line drawings

4.7.27.2.2 Multiview and multisheet illustrations

4.7.27.2.3 Photographs

ix

4.7.27.2.3.1 Photograph quality

4.7.27.2.3.2 Retouching

4.7.27.2.3.3 Use of photographs in place of line drawings

4.7.27.2.4 Engineering drawings

4.7.27.2.5 Diagrams

4.7.27.2.5.1 Diagram specifications

4.7.27.2.5.2 Types of diagrams

4.7.27.2.6 Charts and graphs

4.7.27.2.7 Tools and test equipment illustrations

4.7.27.3 Elements of illustrations

4.7.27.3.1 Border rules and boxes

4.7.27.3.2 Use of the human figure

4.7.27.3.3 Credit lines

4.7.27.3.4 Callouts

4.7.27.3.4.1 Index numbers

4.7.27.3.4.2 Leader lines and arrowheads

4.7.27.3.5 Illustration legends

4.7.27.3.6 Procedures on illustrations

4.7.27.4 Graphic techniques

4.7.27.4.1 Figure numbers

4.7.27.4.2 RPSTL figure numbering

4.7.27.4.3 Foldout figure numbering

4.7.27.4.4 Multisheet numbering

4.7.27.4.5 Figure titles

4.7.27.4.5.1 Figure title format

4.7.27.4.5.2 Figure title placement

4.7.27.4.6 Illustration identification numbers

4.7.27.4.7 Portraying signal flow

4.7.27.4.8 Color in illustrations

4.8 Changes/Revisions

4.8.1 Changes for TMs

4.8.1.1 Changes

4.8.1.2 Changed work packages

4.8.1.3 Changed front and rear matter pages

4.8.1.4 Change symbols for text and tables

4.8.1.5 Change symbols for illustrations

4.8.1.6 Changes to RPSTL work packages

4.8.2 Complete TM revisions

5. DETAILED REQUIREMENTS

5.1 Technical content preparation

5.2 Preparation of front and rear matter

5.2.1 Front matter <paper.frnt>

5.2.1.1 Front cover <frntcover>

5.2.1.1.1 TM number for joint service TMs <tminfono>

x

5.2.1.1.2 National Overhaul Standards statement (TM/NMWR/DMWR with NMP

Overhaul Standards Only)

5.2.1.1.3 Weapon system name <weapon-system>

5.2.1.1.4 Availability statement (DMWR/NMWR only) <avail>

5.2.1.1.5 Supersedure notice for revisions only <super>

5.2.1.1.6 Disclosure notice <disclos>

5.2.1.1.7 Distribution statement <dist>

5.2.1.1.8 Export Control Warning <export>

5.2.1.1.9 Destruction notice <destr>

5.2.1.1.10 General purpose notice <general_purpose_notice>

5.2.1.1.11 Service nomenclature <servnomen>

5.2.1.1.12 TM Publication date <date>

5.2.1.1.13 For Army communications security (COMSEC) manuals use

5.2.1.2 (MC) Promulgation letter <promulgation>

5.2.1.3 Warning summary (including first aid data) <warnsum>

5.2.1.3.1 First Aid <first_aid>

5.2.1.4 Change transmittal page <chgsheet>

5.2.1.5 List of effective pages/work packages <loepwp>

5.2.1.5.1 Types of publications

5.2.1.5.2 Exempted publications

5.2.1.5.3 Types of pages to be included

5.2.1.5.4 Exempted pages

5.2.1.5.5 Change numbers

5.2.1.5.6 Listing the pages

5.2.1.5.7 Numbering the list of effective pages/work packages

5.2.1.5.8 List of effective pages/work packages for RPSTLS

5.2.1.5.9 Multi-service manuals

5.2.1.5.10 Multi-volume manuals

5.2.1.5.11 Dates of Issue for changes

5.2.1.6 Title block page <titleblk>

5.2.1.6.1 Reporting errors and recommending improvements statement <reporting> ...53

5.2.1.7 Preventive maintenance services and phased maintenance inspection manuals title block page with warning data (Aviation only)

5.2.1.8 Table of contents <contents>

5.2.1.9 “How To Use This Manual” information (Except RPSTLs and

DMWRs/NMWRs) <howtouse>

5.2.1.9.1 International standardization agreements

5.2.2 Rear matter <rear>

5.2.2.1 Glossary (Except RPSTL) <glossary>

5.2.2.2 Alphabetical index (Except RPSTL) <aindx>

5.2.2.3 Reporting errors and recommending improvements DA Form 2028

<da2028>

5.2.2.4 Authentication page <authent>

5.2.2.5 Foldout pages (Except RPSTL) <foldsect>

5.2.2.6 Blank forms

xi

5.2.2.7 Back cover <back>

6. NOTES

6.1 Intended use

6.2 Acquisition Requirements

6.3 Tailoring guidance

6.4 DELETED

6.5 Subject Term (Keyword) Listing

6.6 Change notations

A CONTENT SELECTION MATRIXES

A.1 SCOPE

A.1.1 Scope

A.2 APPLICABLE DOCUMENTS

A.3 DEFINITIONS

A.4 GENERAL REQUIREMENTS

A.5 DETAILED REQUIREMENTS

A.5.1 Tailoring requirements for technical manuals A.5.1.1 Publication Titles A.5.1.2 Technical content tables A.5.2 Intended use A.5.3 Acquisition requirements

B GENERAL INFORMATION, EQUIPMENT DESCRIPTION, AND THEORY

OF OPERATION

B.1 SCOPE

B.1.1 Scope

B.2 APPLICABLE DOCUMENTS

B.3 DEFINITIONS

B.4 GENERAL REQUIREMENTS

B.4.1 General B.4.2 Maintenance level applicability B.4.3 Preparation of digital data for electronic delivery B.4.4 Use of the DTD/XSLs B.4.5 Content structure and format B.4.6 Style and format B.4.7 Work package development xii

B.4.8 Safety devices and interlocks B.4.9 Electrostatic discharge (ESD) sensitive parts B.4.10 Nuclear hardness B.4.11 Selective application and tailoring

B.5 DETAILED REQUIREMENTS

B.5.1 Preparation of general information, equipment description, and theory of operation B.5.1.1 Required general information, equipment description, and theory of operation data work packages B.5.2 General information work package <ginfowp> B.5.2.1 Work package identification information <wpidinfo> B.5.2.2 Initial setup information <wpinfo> B.5.2.3 Scope <scope> B.5.2.4 Maintenance forms, records, and reports <mfrr> B.5.2.5 Reporting equipment improvement recommendations <eir> B.5.2.5.1 (MC) Additional reporting equipment improvement recommendations

Marine Corps TMs B.5.2.6 Hand receipt (HR) manuals (Field or below only) <handreceipt> B.5.2.7 Corrosion prevention and control <cpcdata> B.5.2.8 Ozone depleting substances (ODS) <odsdata> B.5.2.9 Destruction of Army materiel to prevent enemy use <destructmat> B.5.2.10 Preparation for storage or shipment <pssref> B.5.2.11 Warranty information <wrntyref> B.5.2.12 Nomenclature cross-reference list <nomenreflist> B.5.2.13 List of abbreviations/acronyms <loa> B.5.2.14 Quality Assurance (QA) (DMWR/NMWR and aviation only) <qainfo> B.5.2.15 Quality of material (Field and above only) <qual.mat.info> B.5.2.16 Safety, care, and handling <sftyinfo> B.5.2.17 Nuclear hardness <hcp> B.5.2.18 Calibration <calref> B.5.2.19 Engineering Change Proposals (ECPs) (DMWR/NMWR only) <ecp> B.5.2.20 Modifications list (DMWR/NMWR only) <modification> B.5.2.21 Deviations and exceptions (DMWR/NMWR only) <deviation> B.5.2.22 Mobilization requirements (DMWR/NMWR only) <mobreq> B.5.2.23 Flight safety critical aircraft parts (FSCAP) (Aircraft only) <fscapreq> B.5.2.24 Cost considerations (DMWR/NMWR only) <cost> B.5.2.25 Supporting information for repair parts, special tools, TMDE, and support equipment (Field and above only) <supdata> B.5.2.25.1 Common tools and equipment B.5.2.25.2 Special tools, TMDE, and support equipment B.5.2.25.3 Repair parts B.5.2.26 Copyright credit line <copyrt> B.5.2.26.1 Proprietary names B.5.2.26.2 Advertising xiii

B.5.3 Equipment description and data work package <descwp> B.5.3.1 Work package identification information <wpidinfo> B.5.3.2 Initial setup information <wpinfo> B.5.3.3 Equipment characteristics, capabilities, and features <eqpinfo> B.5.3.4 Location and description of major components (Except Conventional

Ammunition and Chemical Manuals) <locdesc> B.5.3.5 Differences between models <eqpdiff> B.5.3.6 Equipment data <eqpdata> B.5.4 Theory of operation work package (Except Conventional and Chemical

Ammunition) <thrywp> B.5.4.1 Work package identification information <wpidinfo> B.5.4.2 Initial setup information <wpinfo> B.5.4.3 Theory presentation B.5.5 General information work package (Preventive Maintenance Services

Manual only) <pms-ginfowp> B.5.5.1 Work package identification information <wpidinfo> B.5.5.2 Initial setup information <wpinfo> B.5.5.3 Maintenance activities <scope> B.5.5.4 General information <geninfo> B.5.6 General information work package (Phased Maintenance Inspection

Manual only) <pm-ginfowp> B.5.6.1 Work package identification information <wpidinfo> B.5.6.2 Initial setup information <wpinfo> B.5.6.3 General information <geninfo> B.5.6.3.1 Phased schedule B.5.6.3.2 Additional general information

B.6 NOTES

C OPERATOR INSTRUCTIONS

C.1 SCOPE

C.1.1 Scope

C.2 APPLICABLE DOCUMENTS

C.3 DEFINITIONS

C.4 GENERAL REQUIREMENTS

C.4.1 General C.4.2 Maintenance level applicability C.4.3 Preparation of digital data for electronic delivery C.4.4 Use of the DTD/XSLs C.4.5 Content structure and format C.4.6 Style and format xiv

C.4.7 Work package development C.4.8 Safety devices and interlocks C.4.9 Electrostatic discharge (ESD) sensitive parts C.4.10 Nuclear hardness C.4.11 Selective application and tailoring

C.5 DETAILED REQUIREMENTS

C.5.1 Preparation of operator instructions C.5.2 Operator instructions work packages C.5.2.1 Work package content C.5.2.2 Types of operator instructions work packages C.5.2.3 Description and use of controls and indicators work package <ctrlindwp>..191 C.5.2.3.1 Work package identification information <wpidinfo> C.5.2.3.2 Initial setup information <wpinfo> C.5.2.3.3 Controls and indicators description tabular option C.5.2.3.4 Controls and indicators description narrative option C.5.2.4 Operation under usual conditions work package <opusualwp> C.5.2.4.1 Work package identification information <wpidinfo> C.5.2.4.2 Initial setup information <wpinfo> C.5.2.4.3 Security measures for electronic data <secref> C.5.2.4.4 Siting requirements <site> C.5.2.4.5 Shelter requirements <shelter> C.5.2.4.6 Assembly and preparation for use <prepforuse> C.5.2.4.7 Initial adjustments, before use, and self-test <initial> C.5.2.4.8 Operating procedures <oper> C.5.2.4.8.1 Operating procedure considerations C.5.2.4.8.2 Decals and instruction plates <instructplt> C.5.2.4.9 Operating auxiliary equipment <operaux> C.5.2.4.10 Preparation for movement <prepmove> C.5.2.5 Operation under unusual conditions work package <opunuwp> C.5.2.5.1 Work package identification information <wpidinfo> C.5.2.5.2 Initial setup information <wpinfo> C.5.2.5.3 Operations under unusual tasks <opunutsk> C.5.2.5.3.1 Security measures for electronic data <secref> C.5.2.5.3.2 Unusual environment/weather <unusualenv> C.5.2.5.3.3 Fording and swimming <fording> C.5.2.5.3.4 Interim Nuclear, Biological, and Chemical (NBC) decontamination procedures <decon> C.5.2.5.3.5 Jamming and Electronic Countermeasures (ECM) procedures <ecm> C.5.2.5.3.6 Degraded operation procedures <degraded> C.5.2.6 Emergency work package <emergencywp> C.5.2.6.1 Work package identification information <wpidinfo> C.5.2.6.2 Initial setup information <wpinfo> C.5.2.6.3 Emergency operation <emergency> C.5.2.6.4 Emergency shutdown <emergency> xv

C.5.2.7 Stowage and decal/data plate guide work package <stowagewp> C.5.2.7.1 Work package identification information <wpidinfo> C.5.2.7.2 Initial setup information <wpinfo> C.5.2.7.3 Introduction <intro> C.5.2.7.4 Stowage guide <stowinfo> C.5.2.7.5 Decal/data plate guide <decalinfo> C.5.2.8 On-vehicle equipment loading plan work package <eqploadwp> C.5.2.8.1 Work package identification information <wpidinfo> C.5.2.8.2 Initial setup information <wpinfo> C.5.2.8.3 Introduction <intro> C.5.2.8.4 Illustrated loading plan list(s) <loaddesc>

C.6 NOTES

D TROUBLESHOOTING PROCEDURES

D.1 SCOPE

D.1.1 Scope

D.2 APPLICABLE DOCUMENTS

D.3 DEFINITIONS

D.4 GENERAL REQUIREMENTS

D.4.1 General D.4.2 Development of troubleshooting instructions D.4.3 Maintenance level applicability D.4.5 Preparation of digital data for electronic delivery D.4.5 Use of DTD/XSLs D.4.6 Content structure and format D.4.7 Style and format D.4.8 Work package development D.4.9 Safety devices and interlocks D.4.10 Electrostatic discharge (ESD) sensitive parts D.4.11 Nuclear hardness D.4.12 Selective application and tailoring

D.5 DETAILED REQUIREMENTS

D.5.1 Testing and troubleshooting philosophy D.5.2 Information to be provided D.5.2.1 Methods of testing and troubleshooting D.5.2.1.1 Manual (nonautomatic) troubleshooting D.5.2.1.2 Semi-automatic or automatic testing and troubleshooting D.5.2.1.3 Testing and troubleshooting using built-in-test equipment D.5.2.1.4 Sensor derived failures D.5.2.1.5 Failure interpretation xvi

D.5.2.2 Types of testing and troubleshooting information D.5.2.2.1 Fault reporting/fault isolation information D.5.2.2.2 Integrated system testing and troubleshooting D.5.2.2.2.1 Integrated systems having self-test or built-in test capability D.5.2.2.2.2 Integrated systems requiring the use of system peculiar test sets D.5.2.2.2.3 Integrated systems requiring the use of common test equipment D.5.3 Troubleshooting procedures content D.5.4 Types of testing and troubleshooting D.5.4.1 Aviation testing and troubleshooting category (Aircraft Troubleshooting

TMs only) <troubleaviationcategory> D.5.4.2 Standard testing and troubleshooting category <troublecategory> D.5.4.3 DMWR/NMWR testing and troubleshooting category (depot only)

<troubledmwrnmwrcategory> D.5.4.4 Master index testing and troubleshooting category

<masterindexcategory> D.5.5 Testing and troubleshooting work packages D.5.5.1 Work package content D.5.5.2 Types of testing and troubleshooting work packages D.5.5.3 Introduction work package (Aircraft Troubleshooting TMs only)

<tsintrowp> D.5.5.3.1 Work package identification information <wpidinfo> D.5.5.3.2 Initial setup information <wpinfo> D.5.5.4 Technical description work packages <techdescwp> (Aircraft

Troubleshooting Manuals only) D.5.5.4.1 Work package identification information <wpidinfo> D.5.5.4.2 Initial setup information <wpinfo> D.5.5.4.3 Equipment description and data <descproc> D.5.5.4.4 Controls and indicators <ctrlindproc> D.5.5.4.5 Theory of operation <thryproc> D.5.5.5 Troubleshooting index work package <tsindxwp> D.5.5.5.1 Work package identification information <wpidinfo> D.5.5.5.2 Initial setup information <wpinfo> D.5.5.5.3 Malfunction/symptom index <tsindx.symptom>/<tsindx.messageword> D.5.5.5.4 Master malfunction/symptom index <tsindx.symptom> D.5.5.5.5 System/subsystem index <tsindx.system> D.5.5.6 Preshop analysis work package (DMWR/NMWR only) <pshopanalwp> D.5.5.6.1 Work package identification information <wpidinfo> D.5.5.6.2 Initial setup information <wpinfo> D.5.5.6.3 Scope <scope> D.5.5.6.4 Preparation Procedures <proc> D.5.5.6.5 Preshop analysis procedures <pshopanal> D.5.5.7 Component checklist work package (DMWR/NMWR only)

<compchklistwp> D.5.5.7.1 Work package identification information <wpidinfo> D.5.5.7.2 Initial setup information <wpinfo> xvii

D.5.5.7.3 Introduction <intro> D.5.5.7.4 Component checklist <compchklist> D.5.5.8 Operational checkout and troubleshooting procedures work packages D.5.5.8.1 Operational checkout and troubleshooting procedures content D.5.5.8.2 Operational checkout and troubleshooting procedure work package development D.5.5.8.3 Operational checkout work package <opcheckwp> D.5.5.8.3.1 Work package identification information <wpidinfo> D.5.5.8.3.2 Initial setup information <wpinfo> D.5.5.8.3.3 Introduction <intro> D.5.5.8.3.4 General procedures and precautions <proc> D.5.5.8.3.5 Pretest setup procedures <hookup> D.5.5.8.3.6 Operational checkout procedures <opcheckproc> D.5.5.8.3.7 Post-operational shutdown procedures <disconnect> D.5.5.8.4 Troubleshooting work package <tswp> D.5.5.8.4.1 Work package identification information <wpidinfo> D.5.5.8.4.2 Initial setup information <wpinfo> D.5.5.8.4.3 Introduction <intro> D.5.5.8.4.4 General procedures and precautions <proc> D.5.5.8.4.5 Pretest setup procedures <hookup> D.5.5.8.4.6 Troubleshooting procedures <tsproc> D.5.5.8.4.7 Post-operational shutdown procedures <disconnect> D.5.5.8.5 Combined operational checkout and troubleshooting work package

<opcheck-tswp> D.5.5.8.5.1 Work package identification information <wpidinfo> D.5.5.8.5.2 Initial setup information <wpinfo> D.5.5.8.5.3 Introduction <intro> D.5.5.8.5.4 General procedures and precautions <proc> D.5.5.8.5.5 Pretest setup procedures <hookup> D.5.5.8.5.6 Operational checkout and troubleshooting procedures D.5.5.8.5.7 Post-operational shutdown procedures <disconnect> D.5.5.8.6 Integrated system troubleshooting procedures work packages

D.6 NOTES

E MAINTENANCE INSTRUCTIONS

E.1 SCOPE

E.1.1 Scope

E.2 APPLICABLE DOCUMENTS

E.3 DEFINITIONS

E.4 GENERAL REQUIREMENTS

E.4.1 General E.4.2 Development of maintenance instructions xviii

E.4.3 Maintenance level applicability E.4.4 Depot Maintenance Work Requirement (DMWR) and National

Maintenance Work Requirement (NMWR) E.4.5 Preparation of digital data for electronic delivery E.4.6 Use of the DTD/XSLs E.4.7 Content structure and format E.4.8 Style and format E.4.9 Work package development E.4.10 Safety devices and interlocks E.4.11 Electrostatic discharge (ESD) sensitive parts E.4.12 Nuclear hardness E.4.13 Selective application and tailoring

E.5 DETAILED REQUIREMENTS

E.5.1 Preparation of maintenance instructions E.5.2 Types of maintenance E.5.2.1 Preventive Maintenance Checks and Services (PMCS) (Except for aircraft TMs, DMWR and NMWR) <pmcscategory> E.5.2.2 Weapon system/equipment, component, assembly, subassembly, and software maintenance with required PMCS (Except for aircraft TMs, DMWR and NMWR) <maintenancepmcscategory>

E.5.2.3 Weapon system/equipment, component, assembly, subassembly, and software maintenance without PMCS (Except for aircraft TMs, DMWR and NMWR) <maintenancecategory>

E.5.2.4 Depot weapon system/equipment, component, assembly, and subassembly maintenance <depotcategory>

E.5.2.5 Aircraft maintenance (aircraft only) <aviationcategory> E.5.2.6 Auxiliary equipment maintenance <auxiliarycategory> E.5.2.7 Ammunition maintenance <ammunitioncategory> E.5.2.8 Test and inspection maintenance (Conventional and chemical ammunition only) <testinspectioncategory> E.5.2.9 Shipment/movement and storage maintenance (Conventional and chemical ammunition only) <shipmentmovementstoragecategory> E.5.2.10 Ammunition marking maintenance (Conventional and chemical ammunition only) (Field or above only) <ammomarkingcategory> E.5.2.11 Preventive maintenance services (Aircraft preventive maintenance services only) <pmscategory> E.5.2.12 Phased maintenance inspections (Aircraft phased maintenance inspection only) <checklistcategory> E.5.3 Maintenance work packages E.5.3.1 Work package content E.5.3.2 Service upon receipt work package (Field only) <surwp> E.5.3.2.1 Work package identification information <wpidinfo> E.5.3.2.2 Initial setup information <wpinfo> E.5.3.2.3 Service upon receipt tasks <surtsk> xix

E.5.3.2.3.1 Siting <siting> E.5.3.2.3.2 Shelter requirements <shltr> E.5.3.2.3.3 Service upon receipt of materiel <surmat> E.5.3.2.3.4 Installation instructions <install> E.5.3.2.3.4.1 Assembly of equipment E.5.3.2.3.4.2 Installation of the equipment E.5.3.2.3.4.3 Special applications E.5.3.2.3.4.4 Van and shelter installations E.5.3.2.3.5 Preliminary servicing of equipment <preserv> E.5.3.2.3.6 Preliminary checks and adjustment of equipment <prechkadj> E.5.3.2.3.7 Preliminary calibration of equipment <precal> E.5.3.2.3.8 Circuit alignment <calign> E.5.3.2.3.9 Ammunition service upon receipt tasks E.5.3.2.3.9.1 Ammunition markings <ammo.markings> E.5.3.2.3.9.2 Classification of defects <ammo.defect> E.5.3.2.3.9.3 Handling <ammo.handling> E.5.3.2.3.9.4 Procedures needed to activate ammunition, mine, etc. <arm> E.5.3.2.3.10 Other service upon receipt task <other.surtsk> E.5.3.2.3.11 Follow-on maintenance <followon.maintsk> E.5.3.3 Equipment / user fitting instructions work package (Field or above only)

<perseqpwp> E.5.3.4 Preventive maintenance checks and services (PMCS), including lubrication instructions (Except for Conventional and Chemical Ammunition, aircraft TMs, DMWR and NMWR)

E.5.3.4.1 PMCS introduction work package <pmcsintrowp> E.5.3.4.1.1 Work package identification information <wpidinfo> E.5.3.4.1.2 Initial setup information <wpinfo> E.5.3.4.1.3 PMCS data E.5.3.4.2 PMCS work package <pmcswp> E.5.3.4.2.1 Work package identification information <wpidinfo>

E.5.3.4.2.2 Initial setup information <wpinfo> E.5.3.4.2.3 PMCS procedures E.5.3.4.2.3.1 PMCS data preparation <pmcstable> E.5.3.4.2.4 Mandatory replacement parts <mrplpart> E.5.3.4.3 Preventive Maintenance Checklist (PMC) (operator only) E.5.3.5 Maintenance work packages (Not required for aircraft PM and PMS manuals only) <maintwp> E.5.3.5.1 Work package identification information <wpidinfo> E.5.3.5.2 Initial setup information <wpinfo> E.5.3.5.3 Maintenance tasks <maintsk> E.5.3.5.3.1 Maintenance task requirements E.5.3.5.3.2 Assembly and preparation for use (aviation only) <prepforuse> E.5.3.5.3.3 Servicing <service> E.5.3.5.3.4 Ground handling <groundtsk> xx

E.5.3.5.3.5 Inspection of installed items <inspinstitm> E.5.3.5.3.6 Removal <remove> E.5.3.5.3.7 Disassembly <disassem> E.5.3.5.3.8 Cleaning <clean> E.5.3.5.3.9 Inspection-acceptance and rejection criteria <acptrejinsp> E.5.3.5.3.10 Nondestructive Testing Inspection (NDTI) <ndti> E.5.3.5.3.11 Repair or replacement <repair-rplc> E.5.3.5.3.12 Alignment <align> E.5.3.5.3.13 Painting <paint> E.5.3.5.3.14 Lubrication <lube> E.5.3.5.3.15 Assembly <assem> E.5.3.5.3.16 Test and inspection <test-inspect> E.5.3.5.3.16.1 Inspection and test of conventional and chemical ammunition or components containing radioactive materials (Field, Below Depot Sustainment, and ASB only) <test-inspect>

E.5.3.5.3.16.2 Pre-embarkation inspection of material in units alerted for overseas movement <test-inspect>

E.5.3.5.3.17 Installation <install> E.5.3.5.3.18 Adjustment <adjust> E.5.3.5.3.19 Calibration <calibration> E.5.3.5.3.20 Radio interference suppression <ris> E.5.3.5.3.21 Placing in service <pis> E.5.3.5.3.22 Testing <test-pass> E.5.3.5.3.23 Preservation, packaging, and marking (DMWR/NMWR only) <ppm> E.5.3.5.3.24 Overhaul and retirement schedule (aircraft only) <orsch> E.5.3.5.3.25 Preparation for storage or shipment <pss> E.5.3.5.3.26 Classification of defects <ammo.defect> E.5.3.5.3.27 Handling ammunition <ammo.handling> E.5.3.5.3.28 Ammunition markings <ammo.markings> E.5.3.5.3.29 Procedures needed to activate ammunition, mine, etc. <arm> E.5.3.5.3.30 Additional maintenance task <other.maintsk> E.5.3.5.3.31 Follow-on maintenance task <followon.maintsk> E.5.3.6 General maintenance work package <maintwp> E.5.3.6.1 Work package identification information <wpidinfo> E.5.3.6.2 Initial setup information <wpinfo> E.5.3.6.3 Maintenance tasks <maintsk> E.5.3.7 Lubrication instructions work package <lubewp> E.5.3.7.1 Work package identification information <wpidinfo> E.5.3.7.2 Initial setup information <wpinfo> E.5.3.7.3 Lubrication instructions E.5.3.7.4 Lubrication charts E.5.3.8 DMWR/NMWR specific maintenance work packages E.5.3.8.1 Facilities work package (DMWR/NMWR only) <facilwp> E.5.3.8.2 Overhaul inspection procedures (OIP) work package (DMWRs/NMWRs only) <oipwp> xxi

E.5.3.8.2.1 Work package identification information <wpidinfo> E.5.3.8.2.2 Initial setup information <wpinfo> E.5.3.8.2.3 Overhaul Inspection Procedures (OIP) E.5.3.8.3 Depot mobilization requirements work package (DMWR/NMWR only)

<mobilwp> E.5.3.8.3.1 Work package identification information <wpidinfo> E.5.3.8.3.2 Initial setup information <wpinfo> E.5.3.8.3.3 Introduction for depot mobilization requirements work package <intro> E.5.3.8.3.4 Mobilization requirements <mobilreq> E.5.3.8.4 QA requirements work package (DMWR/NMWR only) <qawp> E.5.3.8.4.1 Work package identification information <wpidinfo> E.5.3.8.4.2 Initial setup information <wpinfo> E.5.3.8.4.3 Statement of responsibility <responsibility> E.5.3.8.4.4 Definitions <definitions> E.5.3.8.4.5 Special requirements for inspection tools and equipment <specialreq> E.5.3.8.4.6 Certification requirements <certreq> E.5.3.8.4.7 Quality program <quality-program> E.5.3.8.4.8 In-process inspections <inprocess> E.5.3.8.4.9 Acceptance inspections <acceptance> E.5.3.8.4.10 First article inspection <first> E.5.3.9 Illustrated list of manufactured items work package (Field level or above only) <manuwp> E.5.3.9.1 Work package identification information <wpidinfo> E.5.3.9.2 Initial setup information <wpinfo> E.5.3.9.3 Introduction for illustrated list of manufactured items work package

<intro> E.5.3.9.4 Index of manufactured items <manuindx> E.5.3.9.5 Illustrations of manufactured items <graphic> E.5.3.10 Torque limits work package (Field level or above only) <torquewp> E.5.3.10.1 Work package identification information <wpidinfo> E.5.3.10.2 Initial setup information <wpinfo> E.5.3.10.3 Introduction <intro> E.5.3.10.4 Torque instructions <torqueval> E.5.3.11 Wiring diagrams work package (Field level or above only) <wiringwp> E.5.3.11.1 Work package identification information <wpidinfo> E.5.3.11.2 Initial setup information <wpinfo> E.5.3.11.3 Introduction <intro> E.5.3.11.4 Wire identification <wireid> E.5.3.11.5 Abbreviations <abbrev> E.5.3.11.6 Wiring diagrams <wiringdiag> E.5.3.12 Aircraft specific maintenance work packages E.5.3.12.1 Preventive maintenance inspections work package (aircraft only)

<pmiwp> E.5.3.12.1.1 Work package identification information <wpidinfo> E.5.3.12.1.2 Initial setup information <wpinfo> xxii

E.5.3.12.1.3 General information and introduction <geninfo> E.5.3.12.1.4 Standards of serviceability E.5.3.12.1.5 Special inspections E.5.3.12.2 Aircraft inventory master guide work package (aircraft only)

<inventorywp> E.5.3.12.2.1 Work package identification information <wpidinfo> E.5.3.12.2.2 Initial setup information <wpinfo> E.5.3.12.2.3 Introduction <intro> E.5.3.12.2.4 Security <security> E.5.3.12.2.5 Inventoriable items <inventoriable> E.5.3.12.2.6 Periods of inventory <prdinv> E.5.3.12.3 Storage of aircraft work package (aircraft only) <storagewp> E.5.3.12.3.1 Work package identification information <wpidinfo> E.5.3.12.3.2 Initial setup information <wpinfo> E.5.3.12.3.3 General information for storage of aircraft work package <geninfo> E.5.3.12.3.4 Flyable storage <flyable>, short term storage <short>, and intermediate storage <intermediate> E.5.3.12.4 Weighing and loading work package (AMC only) <wtloadwp> E.5.3.12.4.1 Work package identification information <wpidinfo> E.5.3.12.4.2 Initial setup information <wpinfo> E.5.3.12.4.3 General information <geninfo> E.5.3.12.4.4 Weighing information <formchart> E.5.3.12.4.5 Loading information <weightinst> E.5.3.13 Auxiliary equipment maintenance work package <auxeqpwp> E.5.3.13.1 Work package identification information <wpidinfo> E.5.3.13.2 Initial setup information <wpinfo> E.5.3.13.3 Auxiliary equipment procedures <maintsk>/<proc> E.5.3.14 Ammunition specific work package E.5.3.14.1 Ammunition maintenance work package <ammowp> E.5.3.14.1.1 Work package identification information <wpidinfo> E.5.3.14.1.2 Initial setup information <wpinfo> E.5.3.14.1.3 Care and handling <ammo.handling> E.5.3.14.1.4 Defective <ammo.defect> E.5.3.14.1.5 Cleaning and painting <service> E.5.3.14.2 Ammunition marking information work package (Field or above only)

<ammo.markingwp> E.5.3.14.3 Foreign ammunition (NATO) work package (Field or above only)

<natowp> E.5.3.15 Preventive maintenance services inspection work packages (aircraft preventive maintenance services only) <pms-inspecwp> E.5.3.15.1 Work package identification information <wpidinfo> E.5.3.15.2 Initial setup information <wpinfo> E.5.3.15.3 Mandatory safety-of-flight inspection items E.5.3.15.4 Area diagram E.5.3.15.5 Standard checklist statements xxiii

E.5.3.16 Phased maintenance inspection work package (aircraft phased maintenance checklist only) <pmi-cklistwp>

E.5.3.16.1 Work package identification information <wpidinfo> E.5.3.16.2 Initial setup information <wpinfo> E.5.3.16.3 Inspection area diagrams <figure> E.5.3.16.4 Phased maintenance checklist

E.5.3.16.5 DELETED

E.5.3.16.6 DELETED

E.5.3.16.7 DELETED

E.6 NOTES

F REPAIR PARTS AND SPECIAL TOOLS LIST (RPSTL)

F.1 SCOPE

F.1.1 Scope

F.2 APPLICABLE DOCUMENTS

F.3 DEFINITIONS

F.4 GENERAL REQUIREMENTS

F.4.1 General F.4.2 Preparation of digital data for electronic delivery F.4.3 Use of the DTD/XSLs F.4.4 Content structure and format F.4.5 Style and format F.4.6 Work package development F.4.7 Selective application and tailoring

F.5 DETAILED REQUIREMENTS

F.5.1 General F.5.2 Parts information development F.5.3 Preparation of RPSTLs F.5.3.1 Separate RPSTL TM F.5.3.2 Parts information chapter <pim> F.5.3.3 RPSTL work packages requirements F.5.3.3.1 RPSTL work packages <pim> included in a maintenance TM F.5.3.3.2 RPSTL work packages included in a DMWR/NMWR F.5.3.3.2.1 Depot repair parts F.5.3.4 Repair parts list, special tools, and kits work package layout F.5.3.5 Introduction work package <introwp> F.5.3.5.1 Work package identification information <wpidinfo> F.5.3.5.2 Initial setup information F.5.3.5.3 Introduction <intro> F.5.3.5.4 Indexed RPSTL illustration and legend <figure> xxiv

F.5.3.6 Repair parts list work package <plwp> F.5.3.6.1 Work package identification information <wpidinfo> F.5.3.6.2 Initial setup information F.5.3.6.3 Repair parts list <pi.category> F.5.3.6.3.1 Repair parts figure title <title> F.5.3.6.3.2 Repair part item <pi.item> F.5.3.6.3.2.1 Item number column <callout> F.5.3.6.3.2.2 SMR code column <smr> F.5.3.6.3.2.3 NSN column <nsn> F.5.3.6.3.2.4 Commercial and Government Entity Code (CAGEC) <cageno> column F.5.3.6.3.2.5 Part number <partno> column F.5.3.6.3.2.6 Description and UOC column F.5.3.6.3.2.7 Quantity column <qty> F.5.3.6.3.2.8 (MC) USMC Quantity per equipment column F.5.3.6.3.2.9 Mandatory Replacement F.5.3.6.3.2.10 Unit of Measure F.5.3.6.3.2.11 Unit of Issue F.5.3.6.3.2.12 Reference Designator F.5.3.6.3.2.13 Next Higher Assembly F.5.3.6.3.2.14 Parts Breakdown Reference F.5.3.6.3.2.15 Other characteristics F.5.3.6.4 Basic Issue Items (BII) (repair parts) F.5.3.6.5 Expendable and durable items F.5.3.7 Repair parts for special tools list work package <stl_partswp> F.5.3.7.1 Work package identification information <wpidinfo> F.5.3.7.2 Initial setup information F.5.3.7.3 Special tools repair parts items list <pi.category> F.5.3.7.3.1 Functional group header <fncgrp> F.5.3.8 Kit parts list work package <kitswp> F.5.3.8.1 Work package identification information <wpidinfo> F.5.3.8.2 Initial setup information F.5.3.8.3 Kits part items list <pi.category> F.5.3.8.3.1 Functional group header <fncgrp> F.5.3.8.3.2 Kit part item group <kititem> F.5.3.8.3.3 Kits part item quantity <qty> F.5.3.9 Bulk items work package <bulk_itemswp> F.5.3.9.1 Work package identification information <wpidinfo> F.5.3.9.2 Initial setup information F.5.3.9.3 Bulk item <pi.item> F.5.3.9.3.1 ITEM column <callout> F.5.3.9.3.2 Functional group header <fncgrp> F.5.3.10 Special tools list work package <stlwp> F.5.3.10.1 Work package identification information <wpidinfo> F.5.3.10.2 Initial setup information F.5.3.10.3 Special tools list <pi.category> xxv

F.5.3.10.3.1 Item number column F.5.3.10.3.2 Functional group header <fncgrp> F.5.3.10.3.3 D-coded items F.5.3.10.3.4 Basis of Issue (BOI) <boi> F.5.3.10.3.5 Quantity column F.5.3.10.3.6 Components list <kititem> F.5.3.11 Cross-reference index work packages F.5.3.11.1 National stock number (NSN) index work package <nsnindxwp> F.5.3.11.1.1 Work package identification information <wpidinfo> F.5.3.11.1.2 Initial setup information F.5.3.11.1.3 NSN index <nsnindx> F.5.3.11.2 Part number index work package <pnindxwp> F.5.3.11.2.1 Work package identification information <wpidinfo> F.5.3.11.2.2 Initial setup information F.5.3.11.2.3 Part number index <pnindx> F.5.3.11.3 Reference designator index work package <refdesindxwp> F.5.3.11.3.1 Work package identification information <wpidinfo> F.5.3.11.3.2 Initial setup information F.5.3.11.3.3 Reference designator index <refdesindx> F.5.3.11.4 Bulk figure reference F.5.3.11.5 Sets and kits F.5.3.12 Illustrations F.5.3.12.1 Arrangement of illustrations F.5.3.12.2 Use of illustrations F.5.3.12.3 Identical parts/item numbers F.5.3.12.4 Identical assemblies

F.6 NOTES

G TECHNICAL MANUALS SUPPORTING INFORMATION

G.1 SCOPE

G.1.1 Scope