090690 - COLOR SCHEDULE.pdf

NGBJV/ILL-RENOVATE BUILDING P-17 183dWing-Illinois Air National Guard Springfield, IL.

Addendum #03 04/07/2021

COLOR SCHEDULE

090690 - 1

SECTION 090690 - COLOR SCHEDULE (Addendum #03)

PART 1 - GENERAL

1.1 SYSTEM DESCRIPTION

A. This section covers only the color of the exterior and interior materials and products that are exposed to view in the finished construction. The word "color", as used herein, includes surface color and pattern. Requirements for quality and method of installation are covered in other appropriate sections of the specifications. Specific locations where the various materials are required are shown on the drawings. Items not designated for color in this section may be specified in other sections. When color is not designated for items, the Contractor shall propose a color for approval.

1.2 SUBMITTALS

A. Submit the following in accordance with Section 013300 SUBMITTAL PROCEDURES:

1. Color Schedule: 3 sets of color boards, 30 days after the Contractor is given Notice to proceed, complying with the following requirements:

a. Color boards shall reflect all actual finish textures, patterns, and colors required for this contract.

b. Materials shall be labeled with the finish type, manufacturer's name, pattern, and color reference.

c. Samples shall be on size 8-1/2 by 11 inch boards with a maximum spread of size 25-1/2 by 33 inches for foldouts.

d. Samples for this color board are required in addition to samples requested in other specification sections.

090690 - 2

PART 2 - PRODUCTS

2.1 COLOR SCHEDULE

A. The color schedule information provided in the following paragraphs lists the colors, patterns and textures required for exterior and interior finishes, including both factory applied and field applied colors. Where color is shown as being specific to one manufacturer, an equivalent color by another manufacturer may be submitted for approval. Manufacturers and materials specified are not intended to limit the selection of equal colors from other manufacturers. In the case of difference between the drawings and specifications, colors identified in this specification govern.

2.2 EXTERIOR FINISHES

A. Standing Seam Metal Roof

1. Color: Award Blue/McElroy Metals

B. Split-Faced Integral Colored CMU

1. Match Existing Canopies at Building P-1

2. Colored Mortar to Match Existing Canopies at Building P-1

C. Smooth Faced Cast Stone

1. Match Existing Canopies at Building P-1.

2. Colored Mortar to Match Canopies at P-1.

D. Exposed Structural Steel

1. Paint Color: Award Blue/McElroy Metals

2.3 INTERIOR FINISHES

A. New Interior Floor Finishes

1. Provide flooring materials to match the colors listed below.

090690 - 3

a. Transition Strips

1) TS-1 - Johnsonite- 28 Medium Grey CG

b. Industrial Floor Coating:

1) EF-1 - Dex-O-Tex - Light Grey

2) ETR - "Existing to Remain."

c. Ceramic Floor Tile:

a) CFT-1 - Dal Tile, Severino, Ceramic Floor Tile, Cenere Fog SV98, 12" x 12" (field tile).

d. Carpet Tile:

1) CPT-1 - Mowhawk Group, Nutopia Matrix, Urban Transit Tile 12BY36- GT414, Intrigue 989, 12" x 36"Transit Tile

e. Exposed Concrete Floor

1) CONC-1 - "Exposed Concrete Floor with Sealer."

B. New Interior Base Finishes

1. Provide base materials to match the colors listed below.

a. Ceramic Tile Base:

a) CB-1 - Dal Tile, Severino, Ceramic Tile Base, Cenere Fog SV98, 3" x 12" (bullnose-P-43C9)

b. Integral Cove Base:

1) ICB-1 - Dex-O-Tex - Light Grey

C. New Interior Wall Finishes

090690 - 4

1. Apply interior wall color to the entire wall surface, including reveals, vertical furred spaces and columns, grilles, diffusers, electrical and access panels, and piping and conduit adjacent to wall surfaces unless otherwise specified. Paint items not specified in other paragraphs to match adjacent wall surface. Provide wall materials to match the colors listed below.

a. Paint:

1) PT-1 - Sherwin Williams - SW 7014 - Eider White

b. Ceramic Wall Tile:

a) CWT-1 - Dal Tile, Severino, Ceramic Wall Tile, Cenere Fog SV98, 6" x 6" (wall tile).

D. New Interior Ceiling Finishes

1. Apply ceiling colors to ceiling surfaces including soffits, furred down areas, grilles, diffusers, registers, and access panels. In addition, apply ceiling color to joists, underside of roof deck, and conduit and piping where joists and deck are exposed and required to be painted. Provide ceiling materials to match the colors listed below.

a. New Exposed Metal Deck:

1) PT-1 - Sherwin Williams - SW 7014 - Eider White

b. New Exposed Structural Framing:

1) PT-1 - Sherwin Williams - SW 7014 - Eider White

c. New Exposed Ductwork and MEP Piping and Equipment:

1) PT-1 - Sherwin Williams - SW 7014 - Eider White

d. Ceiling Panels:

a) ACT-1 - Armstrong - Textured, Color: White (#942), Contractor Series

e. Existing Spaces:

090690 - 5

a) ETR - Existing to Remain.

b) EXP - Exposed to Structure

E. Interior Trim

1. Provide interior trim to match the colors listed below.

a. New Steel Doors:

a) PT-2 - Sherwin Williams SW7016 - Mindful Gray

b. New Steel Door Frames:

1) PT-3 - Sherwin Williams SW7017 - Dorian Gray

c. New Fire Extinguisher Brackets:

1) Factory Standard Red

F. Interior Miscellaneous

1. Provide miscellaneous items to match the colors listed below.

a. Signage Message Color:

1) Match Base Signage

b. Signage Background Color:

1) Match Base Signage

c. Signage Frame:

1) Match Base Signage

d. New Access Panels:

1) Match adjacent wall surfaces

e. Millwork

090690 - 6

a) (SS-1) Countertops- Formica- Everform Solid Surface - Luna Steel, (415).

b) (PL-2) - Lower Cabinet-Formica-Fog, Matte Finish (961-58)

f. New Electrical Switches and Receptacles:

1) White

g. New Electrical Switch and Receptacle Wall Plates:

1) White

h. New Telecommunication Receptacle Wall Plates:

1) White

i. New Electrical Panels:

1) Match adjacent wall surfaces

PART 3 - EXECUTION

A. (Not Applicable)

END OF SECTION 090690