Amendment 4 - Questions and Answers Round 3 REVISED.pdf
PDF 232 KB Posted
- Attached to
- Construct 176WG Munitions Inspection/Assembly Facility Federal contract opportunity
- Solicitation number
- W50S6L-20-B-0010
About this file
This document contains an amendment to the solicitation for the construction of a Munitions Inspection Assembly Facility project. Work includes constructing the maintenance and inspection facility, insulation, power, surge protection, communications infrastructure, HVAC, plumbing, grounding, and lighting. Utilities relocation and an exterior parking area are also required. The option to provide, terminate, and connect associated telecommunications cabling is included. The project value is between $1 million to $5 million. A bid bond of 20% is required and the construction duration is 365 days after notice to proceed. The solicitation is available on betaSAM and contractors must be registered in SAM with a CAGE code. The requirement is a total small business set-aside with a NAICS code of 236220 and size standard of $39.5 million average annual revenue.
View the file
Other files for this federal contract opportunity
Show all 20
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Amendment No. 4 – Q&A Round 3 (REVISED)
Date: 07/24/20
Project: Construct Munitions Inspection Assembly Facility
Project No.: FXSB162207
The following changes, additions, and/or clarifications shall be made to the drawings/specifications for the work of the above project.
This addendum forms a part of the contract documents and in case of a conflict between drawings, specifications, and this addendum, the addendum shall govern.
Question 1:
Drawing CS101 shows no profile for water service. Specification section 221113 3.4 E calls for bury piping with depth of cover over top at least 36 inches, with top at least 12 inches below level of maximum frost penetration. Specifications and drawings do not call out a frost level. Is the intent to install the water line with only 36” of cover?
176 CES Response: Drawing CS101, design is based on means and methods which leaves room for contractor to develop best solutions. Specification section 221113 3.4, in addition to existing verbiage, add that contractor is to cover line with 2 inches of blue board insulation for every foot shy of ten (10) feet that they decide to bury the line and that the width of blue board will need to be extended out and buried at a depth to form a 45 degree angle with the line.
Question 2:
Drawing sheet M210 shows a 2” CW pipe extending out from under the slab 5’ at an elevation ‐
2’3”. Please confirm it is the intent to install this water piping install BOP at ‐2’3”
176 CES Response: Extension out shall be adequately insulated and covered with blue board in same fashion as described in question 1.
Question 3:
Drawing CS101/102 shows no profile for sewer service. Specification section 221313 3.2 F‐2 calls install piping with 36‐inch minimum cover. Please confirm it is the intent to install the sewer line with only 36” of cover.
176 CES Response: Same response as question 1 above regarding covering.
Question 4:
Question 4: Drawing Sheet M210 shows a 4” sewer pipe extending out from the slab 5’ at an elevation ‐2’6”. Please confirm it is the intent to install this sewer piping at I.E ‐2’6”
176 CES Response: Same response as question 2 above regrading requirement for covering.
Question 5:
What is the size and type of watermain that we are tying into on CS101 note 13?
176 CES Response: The size of the pipe is 6”, the type is currently unknown. Bid accordingly based on the information in the specification.
Question 6:
CS101 calls for a 4” water line M 210 calls for a 2” water line. Please confirm that we are to install a 4” waterline and reduce it to a 2” waterline at the building service.
176 CES Response: Confirmed
File details come from the government source that posted it. Updated .