Attachment 0019 - SPI AM60201888-01 - MAIN FRAME ASSEMBLY_COMBINED.DOCX

SPECIAL PACKAGING INSTRUCTION

Form Approved OMB No. 0704-0188

Public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, Va 222024302, and to the Office of Management and Budget, Paperwork Reduction Project(07040188). Washington, DC 20503. Please do not return your form to either of these addresses.

18.

STEPS

19.

REQD

20.

DESCRIPTION

14. DRYING

15. PACKING

a. LEVEL A

MIL-STD-2073-1

b. LEVEL B

MIL-STD-2073-1

16. MARKING

17. NOTES/DRAWING

SPECIFICATIONS, STANDARDS AND DRAWINGS LISTED HEREIN WHICH ARE IN EFFECT ON THE DATE OF THE SOLICITATION FORM A PART OF THIS PACKAGING INSTRUCTION. THE APPLICABLE GENERAL AND REFERENCED REQUIREMENTS OF SPECIFICATION MIL-STD-2073-1 FORM PART OF THESE INSTRUCTIONS. UNLESS OTHERWISE SPECIFIED, MATERIALS WILL BE MINIMUM SIZE IN ACCORDANCE WITH MIL-STD-2073-1. WEIGHTS AND SIZES ARE ESTIMATED AND MAY VARY SLIGHTLY. INTERMEDIATE PACKAGING AND PACKING WILL BE IN ACCORDANCE WITH SPECIFICATION MIL-STD-2073-1 OR AS OTHERWISE SPECIFIED HEREIN.

TOLERANCES SHALL BE IN ACCORDANCE WITH MATERIAL SPECIFICATIONS. QUALITY PERFORMANCE AND TESTING REQUIREMENTS SHALL BE IN CONFORMANCE WITH MIL-STD-2073-1, OR AS OTHERWISE SPECIFIED.

* UNLESS OTHERWISE SPECIFIED, CLEANING AND DRYING SHALL BE IN ACCORDANCE WITH PARAGRAPH 5.2.1 OF MIL-STD-2073-1.

IN ACCORDANCE WITH THE REQUIREMENTS OF INTERNATIONAL STANDARDS FOR PHYTOSANITARY MEASURES (ISPM) 15, THE FOLLOWING COMMERCIAL HEAT TREATMENT PROCESS HAS BEEN APPROVED BY THE AMERICAN LUMBER STANDARDS COMMITTEE (ALSC) AND IS REQUIRED FOR ALL WOOD PACKAGING MATERIAL (WPM). WPM IS DEFINED AS WOOD PALLETS, SKIDS, LOAD BOARDS, PALLET COLLARS, WOODEN BOXES, REELS, DUNNAGE, CRATES, FRAMES, AND CLEATS. PACKAGING MATERIALS EXEMPT FROM THE REQUIREMENTS ARE MATERIALS THAT HAVE UNDERGONE A MANUFACTURING PROCESS SUCH AS CORRUGATED FIBERBOARD, PLYWOOD, PARTICLEBOARD, VENEER AND ORIENTED STRAND BOARD. ALL WPM SHALL BE CONSTRUCTED FROM HEAT TREATED (HT TO 56 DEGREES CENTIGRADE FOR 30 MINUTES) LUMBER AND CERTIFIED BY AN ACCREDITED AGENCY RECOGNIZED BY THE ALSC IN ACCORDANCE WITH WOOD PACKAGING MATERIAL POLICY AND WOOD PACKAGING MATERIAL ENFORCEMENT REGULATIONS (SEE URL:

HTTP://WWW.ALSC.ORG). ALL MATERIALS MUST INCLUDE CERTIFICATION MARKINGS IN ACCORDANCE WITH ALSC STANDARDS AND BE PLACED IN AN UNOBSTRUCTED AREA THAT WILL BE READILY VISIBLE TO INSPECTORS. PALLET MARKINGS SHALL BE APPLIED TO THE STRINGER OR BLOCK ON DIAGONALLY OPPOSITE SIDES AND ENDS OF THE PALLET AND BE CONTRASTING AND CLEARLY VISIBLE. ALL DUNNAGE USED IN CONFIGURING AND/OR SECURING THE LOAD SHALL ALSO COMPLY WITH ISPM 15 AND BE MARKED WITH AN ALSC APPROVED DUNNAGE STAMP. FAILURE TO COMPLY WITH THE REQUIREMENTS OF THIS RESTRICTION MAY RESULT IN REFUSAL, DESTRUCTION, OR TREATMENT OF

MATERIALS AT THE POINT OF ENTRY.

A. CAP CONNECTORS WITH PROTECTIVE CAPS IF APPLICABLE. IF NO CAPS ARE PROVIDED, WRAP ENDS OF ITEM IN ONE LAYER OF PPP-C-795, CELLULAR PLASTIC FILM CUSHIONING CLASS 1; OR A-A-3129, OPEN CELL PLASTIC CUSHIONING TYPE II, GRADE A; OR PPP-C-1797, POLYPROPYLENE FOAM CUSHIONING TYPE I AND SECURE WITH TAPE.

DO NOT ALLOW TAPE TO BE IN CONTACT WITH CABLE OR CONNECTOR.

WSC: ITEM SIZE: 46.0 X 40.8 X 34.0 ITEM WEIGHT: 525.0 APPROVED: NELSON OLIVEIRA

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

DD Form 2169, JUN 97 Previous editions are obsolete Page 1 of 2 Pages

SPECIAL PACKAGING INSTRUCTION (CONTINUATION SHEET)

Form Approved OMB No. 0704-0188

The public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, Va 222024302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subjected to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THIS ADDRESS.

17. NOTES/DRAWINGS

B. ITEM SHALL BE WRAPPED IN A-A-59136 CUSHIONING AND SECURED WITH SPECIFIED TAPE SO THAT CORNERS AND SMALL EXTRUSIONS OF ITEM SHALL BE PROTECTED. TAPE MAY NOT COME IN CONTACT WITH ITEM.

C. THE CONTAINER WILL BE CONSTRUCTED IN ACCORDANCE WITH THIS PACKAGING INSTRUCTION AND ASTM D6251/D6251M, TYPE III, CLASS 2, STYLE A WITH 2 SKIDS. SKIDS WILL BE CONSTRUCTED OF 4” x 4” LUMBER AND HAVE A 45 DEGREE BEVEL ON SKID ENDS. INSIDE DIMENSIONS SHALL BE 31.0” x 11.0” x 14.0”. ALL SIDES SHALL BE CONSTRUCTED FROM B/C FINISH PLYWOOD. CLEATS SHALL BE CONSTRUCTED USING 1” x 2” NOMINAL LUMBER. CLEATS ARE REQUIRED ON THE TOP PANEL RUNNING BOTH THE LENGTH AND WIDTH OF THE CONTAINER. INTERMEDIATE CLEATS SHALL BE USED ON ALL SIDES OF THE CONTAINER FOR REINFORCEMENT. ITEM SHALL HAVE A TIGHT FIT WITHIN CRATE TO PREVENT MOVEMENT DURING TRANSIT. TO ENSURE TIGHT FIT, BRACE AS NECESSARY OR FILL VIOD SPACE WITH DUNNAGE.

D. THIS SPECIAL PACKAGING INSTRUCTION SHALL ALSO BE USED TO DETAIL THE PACKAGING REQUIREMENTS OF THE FOLLOWING ITEMS:

· 60201888-03-C02-L01 – TR MAIN FRAME ASSEMBLY

· 60206055-08-CXX-L01 – LP MAIN FRAME ASSEMBLY

· 60207888-03-C01-L01 – TR MAIN FRAME ASSEMBLY

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

DD Form 2169, JUN 97 Previous editions are obsolete Page 2 of 2 Pages