- Attached to
- High Throughput Visible-Wavelength Multispectral Filter Arrays via Spectral Multiplexing
- Solicitation number
- SF24A-T005
About this file
This document is a Statement of Objectives for federal contract topic SF24A-T005 titled "High Throughput Visible-Wavelength Multispectral Filter Arrays via Spectral Multiplexing."
The objective is to design and fabricate a multiplexing multispectral filter array covering visible wavelengths that achieves higher optical throughput than conventional narrowband arrays with equivalent bandwidth and spectral resolution. Current visible-wavelength multispectral filter array technologies suffer from low light throughput because each pixel measures a single wavelength at a single spatial location, resulting in low signal levels at high spectral resolutions and making hyperspectral video difficult due to required integration times. The performer will develop a multiplexing filter array where each filter is sensitive to multiple wavelengths simultaneously, mount it onto an off-the-shelf monochromatic camera, and demonstrate scene sampling and demosaicking with success measured by signal-to-noise ratio, integration time, spectral resolution, and bandwidth compared to commercial narrowband multispectral filter arrays.
Phase I requires modeling and simulation to determine a deposition recipe for the multiplexing filter array onto glass, use of simulated filter transmission spectra to model sampling and demosaicking of a standard hyperspectral test image, and identification of fabrication facilities. Phase II involves fabricating the filter array using identified facilities, characterizing the array, aligning and mounting it to a calibrated sensor, acquiring hyperspectral measurements, demosaicking the data to recover the hyperspectral datacube, and comparing results to imagery from commercial pushbroom hyperspectral cameras, with the fabricated filter array attached to the provided sensor as the deliverable. Phase III includes characterizing spatial and spectral resolution, building a mounting system for drone attachment, and performing field tests acquiring hyperspectral video of moving ground targets from an aerial platform. The technology area is Sensors with Space Technology as the modernization priority. No CMMC level requirement applies. No Technical Point of Contact is designated.
View the file
Other versions and copies of SF 24A
| File | Revision | Posted | Attached to |
|---|---|---|---|
| SF24A-T007.pdf | Revision not stated | SPoC Resilient Basing | |
| SF24A-T006.pdf | Revision not stated | Low Size, Weight, and Power, High Flux Atomic Source for Scalable Manufacturing | |
| SF24A-T004.pdf | Revision not stated | Integrated lasers and non-magnetic isolators for optical clock technologies | |
| J.4._SF24a_(Payment_Bond).pdf | Revision not stated | DREDGE BOAT BASIN / ACCESS CHANNEL USCG STA. BRUNSWICK, GA |
Who attaches SF 24A
On GovTribe
Work with this file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
SF24A-T005: High Throughput Visible-Wavelength Multispectral Filter Arrays via Spectral Multiplexing
PROJECTED CMMC LEVEL REQUIREMENT:
N/A
TECHNOLOGY AREAS:
Sensors
MODERNIZATION PRIORITIES:
Space Technology
KEYWORDS:
Multispectral Filter Array; Multiplexing Optics; Hyperspectral Imaging; Remote Sensing; Optical Filter Fabrication;
Optical Coatings
ADDITIONAL INFORMATION
N/A
OBJECTIVE:
To design and fabricate a multiplexing multispectral filter array covering the visible wavelengths that achieves a higher optical throughput than a narrowband array with equivalent bandwidth and spectral resolution.
DESCRIPTION:
Describe the work you would like to see accomplished to meet the objective stated above. Character limit 25,000 NOTE: Please do not write any Acronyms in the Topic Description. Spell out everything. Also no mathematical symbols.
To design and fabricate a multiplexing multispectral filter array covering the visible wavelengths that achieves a higher optical throughput than a narrowband array with equivalent bandwidth and spectral resolution.
Current visible-wavelength multispectral filter array technologies suffer from low light throughput because every pixel on the sensor only measures a single wavelength at a single spatial location. Multiple pixels are then considered together to construct the spectral signature over that group of pixels. This approach, while intuitive, leads to low light levels as the spectral resolution increases, since each pixel sees an ever-smaller piece of the object spectrum. The result of this is that high spectral resolution hyperspectral video becomes difficult due to the high integration times necessary to measure the signal. To resolve this issue, the performer will design and fabricate a visible-wavelength multiplexing multispectral filter array, where each filter is sensitive to many wavelengths at once. The performer will then mount their fabricated array onto an off-the-shelf monochromatic camera and demonstrate scene sampling and demosaicking. Success will be defined by the SNR, integration time, and spectral resolution and bandwidth compared to those of an off-the-shelf narrowband multispectral filter array.
PHASE I:
Modeling and simulation will be performed to determine a recipe for depositing a multiplexing filter array onto glass. The simulated filter transmission spectra will be used to model the sampling and demosaicking of a standard hyperspectral test image. Facilities for filter array fabrication will be identified by the performer.
PHASE II:
The multispectral filter array will be fabricated using the facilities identified by the performer during the Phase I.
The performer will then characterize the array and align and mount it to a calibrated sensor. Hyperspectral measurements will then be acquired by the camera, demosaicked to recover the hyperspectral datacube, and then compared to imagery of the same scene acquired with an off-the-shelf pushbroom hyperspectral camera. The Phase II deliverable will be the fabricated filter array attached to the provided sensor.
PHASE III DUAL USE APPLICATIONS:
The spatial and spectral resolution of a camera with the affixed filter array will be characterized. A mounting system will be built for the camera to allow it to be attached to an off-the-shelf drone. A field test will be performed in which hyperspectral video of multiple moving ground targets with diverse spectral content will be acquired from a drone.
REFERENCES:
Harwitt, M. and Sloane, N., "Hadamard Transform Optics," Academic Press, 19791.
Oliver, J. et al., “Filters with random transmittance for improving resolution in filter-array-based spectrometers,” Opt. Expr., 21(4), 2013
2.
Bian et al., "A low-cost integrated hyperspectral imaging sensor with full temporal and spatial resolution at VIS-NIR wide range," arXiv, arXiv:2306.11583v1, 2023.
3.
TECHNICAL POINT OF CONTACT (TPOC):
None
File details come from the government source that posted it. Updated .