High Throughput Visible-Wavelength Multispectral Filter Arrays via Spectral Multiplexing

Closed Solicitation Posted

Solicitation number
SF24A-T005
Agency
Responses due
Set-aside
Total Small Business

Opportunity facts

More information

Notice details come from DoD SBIR/STTR (DSIP). Updated .

About this opportunity

The Department of the Air Force Materiel Command Research Laboratory (Air Force Research Laboratory) sought proposals under DoD STTR topic SF24A-T005 for a visible-wavelength multispectral filter array that achieves higher optical throughput than narrowband arrays with equivalent bandwidth and spectral resolution, with proposals due February 21, 2024. The Set Aside is Total Small Business, and that deadline has passed.

Phase I requires modeling and simulation to determine a deposition recipe for the filter array onto glass, simulated filter transmission spectra to model sampling and demosaicking of a standard hyperspectral test image, and identification of fabrication facilities. Phase II requires fabricating the array at identified facilities, characterizing it, mounting it to a calibrated sensor, acquiring hyperspectral measurements, and comparing results to imagery from commercial pushbroom hyperspectral cameras, with the fabricated array attached to the provided sensor as the deliverable. Phase III covers characterizing spatial and spectral resolution, building a mounting system for drone attachment, and field testing hyperspectral video acquisition of moving ground targets from an aerial platform.

Success is measured by signal-to-noise ratio, integration time, spectral resolution, and bandwidth compared to commercial narrowband multispectral filter arrays. The technology area is Sensors, with Space Technology as the modernization priority. The NAICS code is 541715 and the PSC is AC12. ITAR is marked No, no CMMC level requirement applies, and no Technical Point of Contact is designated.

Notice text

DoD STTR topic SF24A-T005

Component: USAF

Command: AFRL-RV

Phase: STTR Phase I

Technology Areas: Sensors

Focus Areas: Space Technology

Keywords: <p>Multispectral Filter Array; Multiplexing Optics; Hyperspectral Imaging; Remote Sensing; Optical Filter Fabrication; Optical Coatings</p>

ITAR: No

Objective:

To design and fabricate a multiplexing multispectral filter array covering the visible wavelengths that

achieves a higher optical throughput than a narrowband array with equivalent bandwidth and

spectral resolution.

Description:

Describe the work you would like to see accomplished to meet the objective stated above. Character limit 25,000

NOTE: Please do not write any Acronyms in the Topic Description. Spell out everything. Also no mathematical symbols.

4

To design and fabricate a multiplexing multispectral filter array covering the visible wavelengths that

achieves a higher optical throughput than a narrowband array with equivalent bandwidth and

spectral resolution.

Current visible-wavelength multispectral filter array technologies suffer from low light throughput because every

pixel on the sensor only measures a single wavelength at a single spatial location. Multiple pixels are then

considered together to construct the spectral signature over that group of pixels. This approach, while intuitive,

leads to low light levels as the spectral resolution increases, since each pixel sees an ever-smaller piece of the

object spectrum. The result of this is that high spectral resolution hyperspectral video becomes difficult due to

the high integration times necessary to measure the signal. To resolve this issue, the performer will design and fabricate a visible-wavelength multiplexing multispectral filter array, where each filter is sensitive to many wavelengths at once. The performer will then mount their

fabricated array onto an off-the-shelf monochromatic camera and demonstrate scene sampling and

demosaicking. Success will be defined by the SNR, integration time, and spectral resolution and bandwidth

compared to those of an off-the-shelf narrowband multispectral filter array.

Phase I:

Modeling and simulation will be performed to determine a recipe for depositing a multiplexing filter array onto glass. The

simulated filter transmission spectra will be used to model the sampling and demosaicking of a standard hyperspectral test

image. Facilities for filter array fabrication will be identified by the performer.

Phase II:

The multispectral filter array will be fabricated using the facilities identified by the performer during the Phase I. The

performer will then characterize the array and align and mount it to a calibrated sensor. Hyperspectral measurements will

then be acquired by the camera, demosaicked to recover the hyperspectral datacube, and then compared to imagery of

the same scene acquired with an off-the-shelf pushbroom hyperspectral camera. The Phase II deliverable will be the

fabricated filter array attached to the provided sensor.

Phase III:

The spatial and spectral resolution of a camera with the affixed filter array will be characterized. A mounting system will be

built for the camera to allow it to be attached to an off-the-shelf drone. A field test will be performed in which hyperspectral

video of multiple moving ground targets with diverse spectral content will be acquired from a drone.

Files

File Type Posted
SF24A-T005.pdf PDF

Similar open opportunities

On GovTribe

Work this opportunity

  • Track it in your pipeline
  • Find teaming partners
  • Similar opportunities
  • Ask GovTribe AI about this opportunity

GovTribe for Federal Contractors