SAMPLE Project SOW Attachment - Security Applications.pdf

Attachment #2 Security Applications

The Government controlled space (primary, rear egress doors, and GOV Parking) shall be secured with a Video Intercom Entry Control (EC) and CCTV / NVR systems. If existing, the current building system(s) must meet or exceed all the referenced specifications below, to be acceptable. A Certified Integrator / Installer per manufacturer is required for extended warranty periods and trouble-free installations for Aiphone, Hanwha (Certified Video Professional / Wisenet Certified Professional (WCP)), ASSA ABLOY, and most other listed equipment manufacturers.

REQUIRED BY LAW: For all supplied communication requirements and electronic security applications, the Lessor (or their contractors) are PROHIBITED (2019 N.D.A.A. law) from providing to the Government any such equipment or services as a substantial or essential component, or as critical technology as part of any system.

These PROHIBITED security / telecommunications products are from any of the following source entities, any subsidiary or affiliate of such source entities: 1) The People’s Republic of China; 2) Huawei Technologies Company; 3) ZTE Corporation; 4) Hytera Communications Corporation, Hangzhou Hikvision Digital Technology Company; 5) or Dahua Technology Company. Lessor (or contractors) must certify the equipment is not from any of these sources and provide written confirmation to the COE Representative prior to installation. Lessor (or contractors) must certify the equipment is not from any of these sources and provide written confirmation to the COE Representative prior to installation. Upon acceptance of the premises, the Lessor or Contractor must re-certify in writing what equipment has been installed, and that all components comply with the 2019 N.D.A.A. requirements.

All supplied / installed components / equipment to be from authorized dealers, and shall be equal to or exceed the performance of the models referenced below.

a. Security Board: Location of Security Board will be located within the storage closet adjacent to the existing communications board, a fixed to wall mount a ¾” thick, 4’-0” W x 8’-0” H fire-retardant treated plywood backboard, at 2’-0” AFF (top edge of backboard to be trimmed 6” below drop ceiling if necessary). The security board location must have 36” of front clearance to facilitate access and have an overall layout as shown on Enclosure #1c.

Quadplex outlets to be flush mounted on the fire-retardant treated plywood backboard(s), and installed at the back of each 12U Cabinet at the lower left corner, as shown on ENCLOSURE #1c and 1d.

Isolated copper grounding plate on each Commo / Security Board(s) connected to a green #6 ground wire will be attached to the building ground or grounding rod in accordance with code standards. An equivalent standard for isolated electrical ground installation is acceptable.

1. Tripp Lite Model # SRW12UDP (dedicated for the EC and CCTV systems): A 12U Security

Cabinet (with lockable door), to be aligned and mounted directly on the right side of the Security Board. Top of cabinet to be at 48” AFF and be used for the NVR keyboard / mouse shelf.

Horizontal and Vertical Spacing between Communications cabinet(s) to be 12” on all sides.

i. Security Cabinet model MUST accommodate quadplex outlet for the NVR, PoE+ switch, and associated equipment as necessary.

ii. Three (3) keys to the Security Cabinet must be provided to the COE Representative for EACH

Military Service (see A.4). Only Facility Managers / ATO’s will have these keys. All Military Services personnel to have read / download / export access (via USB extension wire) when an event occurs. The system must be secured (locked) at all times.

2. PoE+ Switch(s) [Model #’s listed in the table(s) under paragraph K]: One (1) primary NETGEAR 48 port PoE+ switch (in unmanaged mode) at a minimum for CCTV and EC hardware.

As required for additional PoE+ ports, an optional / secondary NETGEAR 24 (or 48) port PoE+ or PoE++ switch (in unmanaged mode) may be needed.

b. Low Voltage / Communications (See CCTV/NVR System – ENCLOSURE #1a, 1b, 1c and 1d and ENCLOSURE #6a, 6b, 6c and 6d for a diagram of requirements / layout).

c. Outlets / Wiring: These voice / data port outlets will be vertically aligned and installed within 2” horizontally on each office space electrical outlet, so the tops of both outlets measure to the same height AFF, or as identified on the approved floor plan. Required 1” conduit terminating 12” above finished wall height. See Paragraph A.1. Permits.

1. Security and Communications Cabinet wiring requirements:

i. Each Military Service will have straight-through BLUE data CAT 6 wires from their Communications Cabinet into their office space. (Should be pre-existing from earlier construction)

ii. Ceiling access points (BLUE data CAT 6 wires) to be covered with a blank standard white faceplate.

iii. The Security Cabinet will have yellow data CAT 6 wires into each Military Service’s office space for the Aiphone desk-tenant stations.

iv. Aiphone Desk-Tenant Station Outlets: Routed from the Security Cabinet PoE+ Switch(s) to designated wall location. These straight through CAT 6 yellow wire(s) labeled on both ends with a female RJ45 cover plate at the wall location.

v. With an 8’ yellow patch wire from wall outlet to the desk-tenant station.

vi. Each labeled wall plate (destination end) shall be equipped with a three (3) port female RJ45 plate. All data port jacks, and straight-through CAT 6 wire (T568B) will be color coordinated and labeled with identification number at both ends. Two BLUE data port jacks & BLUE wires will be routed to the Commo Board and one yellow data port jack & yellow wire routed to the Security Board PoE+ Switch(s).

vii. The RJ45 connector can then be connected to a modem, router, switch, adaptive security appliance, etc., which may be installed by the Military Service’s telecom provider.

viii. All Communications faceplates will be color coordinated with the electrical faceplates. See each Military Service Attachment for specific color requirements for faceplates.

ix. Required wiring / data port jack colors: All data port jacks and straight-through (T568B) CAT 6 wiring shall be color coordinated and labeled. All wiring shall be contained in appropriate conduit in walls and the ceiling interstitial / plenum space to be arranged in a tight compact arrangement / appearance in raceways.

Military Services Comms (Voice & Data):

a. Two (2) CAT 6 wiring & data port jacks color = BLUE. (pre exsisting) EC Systems (paragraph K.3):

a. CAT 6 wiring & data port jack color = YELLOW.

CCTV / NVR systems (paragraph K.4) & Mounted TV / monitors (paragraph D.4):

a. CAT 6 wiring & data port jack color = RED.

x. All wiring for Commo / Security Board Cabinets components shall be color coordinated, labeled with Port Identification numbers at both ends, have a minimum of three (3) feet of slack, contained in a horizontal or vertical organizer / enclosure (similar to Legrand Model #SHMC2RU) and in an organized manner. All wires shall be labeled referencing port numbers:

2. Conduit / Raceways:

i. Conduit size to be capable of handling all data wires and access needs for ALL the

Military Services

ii. Voice and data wall / ceiling / floor outlet box conduit runs to the commo board shall terminate

12” above finished wall height. Note: See paragraphs D. & K.

iii. Wiring above ceiling (interstitial / plenum space) shall be contained in a raceway, if not installed in conduit.

1. Security Hardware / Application Requirements (EC & CCTV/NVR Systems): Contractor will advise the COE Representative on any unique site / office requirement(s) which will require any modifications to these specified security components.

a. Off network / offline Hardware.

b. Certified Integrators / Installers (warranty):

1. Aiphone - https://www.aiphone.com/kbtopic/ix-series-integrations-hanwha

2. Hanwha Vision STEP Partner - https://hanwhavisionamerica.com/partner-portal/

3. ASSA ABLOY (Rockwood, Securitron, Accentra, AdamsRite, and Pemko components) -https://www.assaabloydss.com/en/support/installation-and-service-partners/certified-integrators

c. EC and CCTV / NVR systems to be installed at the same time as they are integrated. Aiphone: IXG support tool file and IXG site specific configuration file to be loaded on the NVR (operating system drive).

d. NVR Computer Bios / Auto Start: Contractor to set / confirm NVR system BIOS settings are set to reboot automatically on power loss with MS Windows Auto Login (NO login password). Bios instructions are as follows:

1. Power On the NVR and press "DEL" or "F1" or "F2" or "F10" to enter BIOS (CMOS) setup utility

(the way to enter into BIOS Settings depends on the computer board manufacturer).

2. Inside BIOS menu, look under the following menus to find for a setting named “Restore on

AC/Power Loss” or “AC Power Recovery” or "After Power Loss", “Advanced” or “ACPI” or "Power Management Setup".

3. Note: The “Restore on AC/Power Loss” setting can be found under different places inside BIOS setup according to computer manufacturer.

4. Set the “Restore on AC/Power Loss” setting to “Power On”.

5. Save and exit from BIOS settings.

e. Static IP Address Schedule: Manually set / confirmed by contractor.

1. Network PoE+ Switch(s) = 192.168.1.1-25 range.

2. Aiphone = 192.168.1.100-199 range – pre-set by Aiphone programming file.

3. CCTV / NVR = 192.168.1.200-255 range.

f. User IDs, Passwords and Door Access Codes: Contractor to coordinate with the COE Representative for setting / integrating user IDs, passwords, and temporary door access codes, including controlled distribution. Contractor to ONLY assist the Military Services facility managers / ATO’s with programming the final door access codes.

1. Both the Aiphone IXG and Hanwha CCTV/NVR systems each require two (2) user / login levels each:

i. Aiphone IXG Support Tool:

Administrator for installer (Recruiters will not have access).

Property Manager for facility managers / ATOs (Recruiters will not have access).

ii. Hanwha / Wisenet Device Manager (CCTV): With these predefined user roles.

Owner for installer / facility managers / ATOs (Recruiters will not have access).

Viewer for onsite Recruiters / personnel.

iii. No MS Windows login passwords. Windows Auto Login only.

2. System User IDs & Passwords (EC, CCTV/NVR/Decoder, PoE+ Switch): User IDs / passwords shall be reset from defaults and set / integrated to match / align with each other. Admin and Owner user login level(s) & passwords to be set / integrated to match / align with each login level for all systems. Local Personnel / Recruiters will only have access to the Wisenet “Viewer” user.

3. Door Access Codes with Controlled Distribution: Contractor to program two (2) temporary and unique access codes for each Military Service present. The EC door-entrance station(s) (e.g. – A4611), and optional Securitron DK-26 individual keypad(s) codes to match #’s (e.g. – 4611) if both units are present. Two (2) separate and unique access codes are necessary for each Military Service.

g. Camera & Door-Entrance Station Tools (Torx Tool): To be stored in a clear sleeve inside the Security cabinet at the Security Board.

h. System Documentation for CCTV/NVR Setup & License Tracking by Contractor (activated licenses for all cameras, EC door-entrance station cameras, etc.):

1. One copy of the system(s) hardware documentation / manuals / login details, and camera licenses are to be stored in a clear sleeve (along with the door-entrance station / camera tool (Torx tool) inside the Security cabinet at the Security Board.

2. Save the following files on the NVR (operating system drive):

i. Screen shots of all license keys and #’s (email second copy to the COE representative).

ii. Create Wisenet project file with current date.

iii. Run Wisenet camera / encoder report “ALL” (email second copy to the COE representative).

iv. Create camera config backup file.

i. Printed Exporting Video Instructions: Provide “how to” instructions on exporting video footage from NVR, via USB extension wire located next to keyboard. Printed instructions to be placed in clear plastic sleeve and mounted above NVR monitor on Security Board.

j. System Training:

1. A Training event will be scheduled and coordinated with the COE Representative for all Military

Services / personnel (see paragraph A.4. for recruiter numbers). Installer(s) will submit to the COE a legible, dated roster with the trainer’s contact information, each Trainee’s name/rank, along with systems covered.

2. Minimum of a 1-hour training session MUST be provided as part of the installation by the contractor to ALL Military Services where the system(s) is installed.

3. On-site training to use “temporary” door access codes with Military Service personnel.

Temporary access codes to be deleted / reprogrammed by Service Facility Managers / ATO’s after training is accomplished.

4. The training will cover minimum items:

i. EC System:

Individual Service access codes with controlled distribution to the Facility Manager / ATO.

System Features and operation of door-entrance station(s), keypads, desk-tenant stations.

RJ45 port and wire colors.

How to disconnect and reconnect desk-tenant stations.

Basic troubleshooting options / methods.

Ensure door release time range is set to 5-10 seconds for electrified doors / keypads.

ii. CCTV/NVR/Decoder with monitor displays:

Review camera placements and system features / settings.

Adjust each camera and Military Branch display for optimal egress / camera views.

What to do if the CCTV system shuts down, or display monitors stop displaying.

Demonstrate automatic restart / reboot NVR and display monitors in each office.

Discuss and provide location of printed “how to” instructions on exporting video footage from NVR.

iii. Facility Managers / ATO’s: When present, detailed training for required (names / emails previously given by COE representative):

Individual system software (Aiphone, Wisenet) instructional demo for logging in.

Demonstrate features and operation on each system present.

How to add/remove recruiter(s) door access code(s) on Aiphone IXG Support Tool and

DK-26 control board.

How to retrieve door entrance history / access control data from Aiphone IXG Support

Tool.

How to disconnect/reconnect desk-tenant stations.

Demonstrate automatic reboot / restart on EACH System, basic trouble shooting options.

How to search / retrieve / export data video from NVR.

What to do if the CCTV system shuts down, or display monitors stop displaying.

3. Video Intercom Entry Control (EC) System (Aiphone IXG Series):

A surface mounted door-entrance station (or keypad) shall be installed at the EXTERIOR PRIMARY- ENTRANCE and SECONDARY EGRESS doors to the military recruiting station as identified on the approved floor plan / AE drawings. Contractor will contact Aiphone and advise the COE before bid submittal of any unique site / office layout requirements which will impact their bid proposal. A Certified Integrator / Installer per manufacturer is required for extended warranty periods and trouble-free installations for Aiphone, Hanwha (Certified Video Professional / Wisenet Certified Professional (WCP)), ASSA ABLOY, and most other listed equipment manufacturers.

a. The EC system components should include the following items in the table below - as applicable (may differ based on the specific recruiting office layout / approved floor plan / AE drawings):

VIDEO INTERCOM ENTRY CONTROL (EC) SYSTEM COMPONENTS TABLE

Application: Model / Skew #’s: Description: Qty: Notes:

Primary Entrance and/or Secondary Egress Doors

IXG-DM7-HIDA

Aiphone - IXG System

Door-Entrance Station (with mounting bracket)

Ea See Note 1, 2, 3, 4, 5.

Door-Entrance Station Mount

SBX-IXGDM7

Aiphone - Surface Mount Box, Includes Rain Hood

Ea

Secondary Egress Doors (when no public access) DK-26 SS

Securitron - Keypad with CPU Board/Controller

Ea Optional Rear Egress Only See Note 4, 11

Each Military Service Space

IXG-2C7

Aiphone - Desk-Tenant

Station 2+ See Note 1, 6

Each Military Service Space

MCW-S/B

Aiphone - Desk-Tenant

Station – Stand Ea Per Desk-Tenant Station

Security Board

IXG-MAA

Aiphone - Network Door Release Relay Adaptor

Selective door release (allows Military Services to release specific doors)

IXG-MK

Aiphone - Guard Station

(includes flush mount kit) 1 See Note 12

FPO250-C8D8E2

LSP - Power Supply

(hardwired on security board) 1 8 Door / 8 Lock, 20A, 12VDC

Security Board (in Security Cabinet)

GS752TPP-

300NAS

NETGEAR – 48 Port Primary PoE+ Switch

Ea 48 Port (expandable with another 24 or 48 port switch)

Security Board (in Security Cabinet)

GS524UP-

100NAS

NETGEAR – 24 Port Optional / Secondary

PoE++ Switch Ea 24 Port PoE++ Switch

(See Note 5)

VIDEO INTERCOM ENTRY CONTROL (EC) NOTES:

1) REQUIRED FOR CONTRACTORS:

a. Contractor MUST complete questionnaire form for Aiphone custom program configuration file, which will be provided to the contractor for each office via email.

b. Programming design questionnaire forms & information to be completed at:

https://www.aiphone.com/support/technical-support/aiphone-programming-questionnaire

2) See https://www.aiphone.com/products/ixg-series for IXG specifics and recruitingcenters@aiphone.com for installation details / questions at recruiting centers.

3) Certified Integrators / Installers (warranty):

a. Aiphone - https://www.aiphone.com/kbtopic/ix-series-integrations-hanwha

b. Hanwha Vision STEP Partner - https://hanwhavisionamerica.com/partner-portal/

c. ASSA ABLOY (Rockwood, Securitron, Accentra, AdamsRite, and Pemko components) -https://www.assaabloydss.com/en/support/installation-and-service-partners/certified-integrators

4) Door release time range: Default of 5-10 seconds for all electrified doors / key pads (IXG, DK-26).

5) Door-entrance station cameras to be connected to the CCTV system. These cameras and desk-tenant stations require a PoE+ Switch connection. If more than 48 ports (or PoE++ ports) are required, add on the optional / secondary PoE+ Switch.

6) Desk-tenant stations to be installed in each Military Service facility (minimum of 2, maximum of 8) for each Military Service recruiter identified in paragraph A.4. Optional wall mounted desk-tenant stations should be placed free and clear of all Military Service accent walls (as identified on approved floor plan / AE drawings). Wall Outlet (yellow data port jack) to desk-tenant station shall include an eight (8) foot yellow straight-through CAT 6 patch wire. In rare cases (as directed by a COE representative or on the approved floor plan / AE drawings) a wall mount for desk-tenant stations may be necessary (wall mount model = IXG-FMK-2C7).

4. Closed Circuit Television System (CCTV) with Network Video Recording (NVR): Installation of system and its components shall be in conformance with the attached CCTV System Example Layouts, U.S. industry standards, manufacturers’ recommendations, and site necessitated requirements.

a. Installed in the Security Closet within a locking security cabinet with the dedicated PoE+ Switch as an off network / offline system (independent of any Military Services network / LAN system).

b. Review CCTV / NVR system layouts below and ENCLOSURE #1c for additional installation requirements / instructions / components placement on Security Board. Note: One NVR per leased location.

c. Each Military Service requires a live video feed from this system. If the non-contiguous spaces are too far apart (e.g. - wiring length or site specific restraints, etc.), a separate PoE+ Switch, wiring and conduit may be required to fully function and cover all Military Services. All non-contiguous space solutions to be coordinated with the COE Representative.

d. A Certified Integrator / Installer per manufacturer is required for extended warranty periods and trouble-free installations for Aiphone, Hanwha (Certified Video Professional / Wisenet Certified Professional (WCP)), ASSA ABLOY, and most other listed equipment manufacturers.

e. The CCTV system components should include the following items in the signage and table below - as applicable (may differ based on the specific recruiting office layout / approved floor plan / AE drawings):

7) See paragraph G.7 for Door Hardware Schedule & release components.

8) All stranded low voltage wire (exit device, keypad, and door position switch) will be 18 AWG stranded wire with label / tag at each end for easy identification and troubleshooting. See ENCLOSURE #6a, 6b, 6c, and 6d for EC example components, wiring and layout diagrams.

9) See paragraph K. for PoE+ Switch & LSP Power supply requirements (hardwired on security board).

10) See communications paragraph E and ENCLOSURE #1a, 1b, 1c and 1d for locations and colors of data port jacks and CAT 6 wires.

11) No Public Access Secondary Doors: A secondary egress door that only Recruiting personnel use to enter the station. Typically, the public or potential recruits do not access thru this door. The “No public access doors” only requires the Securitron DK-26 Keypad with controller (vs the Aiphone door-entrance station).

12) Door position switches to activate shared egress door(s) chime(s). Primary shared egress doors shall have a single-tone (e.g. - “ding”), and secondary shared egress door(s) shall have two-tones (e.g. - “ding-dong”).

CCTV System Components

Application: Model / Skew #’s: Description: Qty: Notes:

Security Board:

Installed inside Security Closet

SRW12UDP

Tripp Lite 12U – Locking

Security Cabinet 1 See Note 1

SMT-2431 Hanwha LED Color Monitor 1 See Note 2

ML411B-B1

VideoSecu BJZ (swivel & tilt)

Monitor Mounting Bracket 1 See Note 3

ICCMSCMA81 Vertical Plastic Wire Duct 1 See Note 4

CCTV System:

Installed inside Locking Security Cabinet

WRT-P-3104W-

16TB

Hanwha Wisenet WAVE VMS (NVR) CCTV System

1 See Note 4

CCTV System minimum requirements: 16TB raw, 170 Mbps recording B / W, (3) 3.5" HDD, (10th Gen) Intel Core i3, 16GB RAM, 256 GB SSD OS Drive, Windows 10 IoT Enterprise, (2) DisplayPort output, (1) DisplayPort to HDMI adapter, Dual GbE NICs, Single 550W P.S., keyboard & mouse, with four (4) USB 3.2, two (2)

USB 2.0, four (4) USB-C 3.2, and one (1) SD card ports. Wave VMS and Four (4) WAVE-PRO “Professional Licenses” Pre-Loaded.

WAVE-PRO-01

Wave VMS Recording License

(1 pack) Ea See Note 4.g

WAVE-PRO-04

Wave VMS Recording License

(4 pack) Ea See Note 4.g

WAVE-PRO-08

Wave VMS Recording License

(8 pack) Ea See Note 4.g

GS752TPP-

300NAS

NETGEAR – 48 Port Primary PoE+ Switch

Ea ⚡ See Note 5

GS524UP-

100NAS

NETGEAR – 24 Port Optional / Secondary PoE++ Switch

Ea ⚡ See Note 5

CAUSBAMF 6 foot USB extension wire 1 See Note 6 Interior Cameras:

Primary & Secondary Egress Door(s) and Common Area Hallways

XND-C8083RV

Hanwha 6MP AI IR Vandal

Dome Camera Ea

See Note 7.a

XNF-9013RV

Hanwha 12MP AI IR Vandal

Dome Fisheye Camera Ea

See Note 7.a

Exterior Cameras:

Primary & Secondary Egress Door Paths

XNF-9013RV

Hanwha 12MP AI IR Vandal

Dome Fisheye Camera Ea See Note 7.b

Camera Connection Only

Aiphone: IXG-DM7-HIDA Door-Entrance Station

Ea See Note 7.b

Exterior / Garage GOV Parking Cameras:

XNV-9083R

Hanwha 4K AI IR Vandal

Dome Camera Ea See Note 7.c

XNP-C8253R

Hanwha 6MP AI IR PTZ Dome Camera – PoE++

Ea See Note 7.c

Camera Mounts:

Where Applicable

Direct Mount XND-C8083RV Camera

Mount (backplate provided) Ea See Note 7.d

(site specific need)

SBP-400WMW

XNF-9013RV Camera Wall &

Pole Mount (backplate provided)

Ea See Note 7.d.

SBP-156KMW

(for a corner mount)

SBP-400WMW

XNV-9083R Camera Wall &

Pole Mount Ea

See Note 7.d

SBP-156KMW

(for a corner mount)

SBP-156WMW

XNP-C8253R PTZ Camera

Wall & Pole Mount Ea

See Note 7.d

SBP-156KMW

(for a corner mount)

CCTV Signage: Custom CCTV Security Sign

(Color Printed on Aluminum) Ea See Note 8

Each Military Service Space:

DU8000

Samsung 55” 4K CCTV

Monitor Ea See Note 9.a

SPD-152

Hanwha PoE Network Video

Decoder (custom screens) Ea See Note 9

SLC3770LBK

Displays2Go, Monitor Mounting

Pole Ea See Note 10

NOTES:

1) Tripp Lite Model # SRW12UDP (dedicated for the EC and CCTV systems): A 12U Security Cabinet

(with lockable door), to be aligned and mounted directly on the right side of the Security Board. Top of cabinet to be at 48” AFF and be used for the NVR keyboard / mouse shelf (see ENCLOSURE #1c for details). Cabinet to include an interior quadplex outlet flush mounted (on the fire-retardant backboard).

Each Military Service to be issued three (3) Security Cabinet keys for only Facility Managers / ATOs to retain.

2) Hanwha 24” LED Color Monitor: Full HD, 1080p (1920x1080), HDMI, VGA, 16:9 aspect ratio, VESA DPM Compatible for NVR System Monitoring. https://hanwhavisionamerica.com/product/smt-2431/

3) Swivel & tilt monitor bracket to be mounted directly above the CCTV keyboard / mouse on the Locking Security Cabinet.

4) Security Hardware / Application Requirements (EC & CCTV / NVR Systems): Contractor will advise the COE Representative on any unique site / office requirement(s) which will require any modifications to these specified security components.

a. Certified Integrators / Installers (warranty):

1. Aiphone - https://www.aiphone.com/kbtopic/ix-series-integrations-hanwha

2. Hanwha Vision STEP Partner - https://hanwhavisionamerica.com/partner-portal/

3. ASSA ABLOY (Rockwood, Securitron, Accentra, AdamsRite, and Pemko components) -https://www.assaabloydss.com/en/support/installation-and-service-partners/certified-integrators

b. EC and CCTV / NVR systems to be installed at the same time as they are integrated. Aiphone: IXG support tool file and IXG site specific configuration file to be loaded on the NVR (operating system drive).

c. Hardware Placement: See paragraph E. Communications and ENCLOSURE #1a, 1b,1c and 1d.

1. NVR Computer and PoE+ Switch(s) to be installed and powered within the Security Cabinet.

2. To include professional component / wiring installation in an organized manner within wiring organizer wherever possible on the Security Board with labeling of source and destination ends of wiring.

d. NVR Computer Bios / Auto Start: Contractor to set / confirm NVR system BIOS settings are set to reboot automatically on power loss with MS Windows Auto Login (NO login password). BIOS instructions are as follows:

1. Power On the NVR and press "DEL" or "F1" or "F2" or "F10" to enter BIOS (CMOS) setup utility

(the way to enter into BIOS Settings depends on the computer manufacturer).

2. Inside BIOS menu, look under the following menus to find for a setting named “Restore on

AC/Power Loss” or “AC Power Recovery” or "After Power Loss", “Advanced” or “ACPI” or "Power Management Setup".

3. Note: The “Restore on AC/Power Loss” setting can be found under different places inside BIOS setup according to computer manufacturer.

4. Set the “Restore on AC/Power Loss” setting to “Power On”.

5. Save and exit from BIOS settings.

e. For more than 24 camera systems, upgrade the Hanwha NVR to the next model WRT-P-5204W 24TB.

f. Recording Standard: Additional hard drive storage may be required to record: all interior cameras on motion recording and all exterior cameras on 24/7 recording at 15 FPS and with AI motion event, recording increased to 30 FPS with full resolution on all cameras. Including all IXG door-entrance station cameras. Recording at H.264 for Aiphone IXG-DM7-HIDA and H.265 minimum for all other cameras. Minimum continuous recording storage capacity of 14 days required. GOV Parking PTZ Cameras with AI person auto-tracking engaged / enabled.

g. All Cameras require a WAVE-PRO License (Pro Recording License / Key) activated on the VMS for recording. Including the embedded camera in the Aiphone IXG-DM7-HIDA. (License are sold in 1 / 4

/ 8 / 16 / 32 packs.) An exported list of all license keys to be provided to the COE representative and printed / stored in the Security Cabinet.

h. All requirements found in paragraph K MUST be followed for setting up the CCTV system.

5) NETGEAR 48 Port PoE+ Switch is required as the primary switch, with additional 24 or 48 optional / secondary PoE++ Switches for PTZ cameras or expansion as needed. See paragraph K.1 for additional PoE+ Switch setup requirements.

6) USB Extension Wire: One (1) 6-foot USB 2.0 (male to female) extension wire plugged into the rear of the NVR and extending on top of the Security Cabinet by the monitor / keyboard.

https://srcomponents.com/products/cables/usb-cables/usb-cable-2-0-aa-male-to-female-6-ft.html

7) CCTV Cameras: No blind spots allowed. See Note 4 above for recording standard settings.

https://hanwhavisionamerica.com/resources/tools/installation-simulator/

a. Interior Cameras - https://www.hanwhasecurity.com/product/xnd-c8083rv/ or https://www.hanwhasecurity.com/product/xnf-9013rv/:

1. Exclusive / single egress door(s) - exiting Government controlled space (XND-C8083RV): One (1) plus camera(s) viewing the exterior entrance door area (viewing only the door entrance area).

2. Shared egress door(s) - exiting Government controlled space (Fisheye camera XNF-9013RV): One

(1) plus camera(s) viewing the exterior entrance door area.

3. Common areas / hallways (Fisheye camera XNF-9013RV for full view / recording of space.): One

(1) plus camera(s) to capture all interior common areas / hallways to include the security closet door.

Cameras to have overlapping views with no blind spots.

b. Exterior Cameras - https://www.hanwhasecurity.com/product/xnf-9013rv/ fisheye camera:

1. Two (2) plus cameras to capture building perimeter at Primary entrance(s).

2. Two (2) plus cameras to capture building perimeter at Secondary Egress’.

3. Camera viewing angles shall provide “visual” paths for “safe egress” from the Government controlled space.

4. Mounting locations and applicable Exterior mounts shall be used to avoid viewing obstructions / blind spots.

5. Aiphone Door-Entrance Station Camera(s): Each Aiphone door-entrance station (IXG-DM7-HIDA) embedded camera(s) requires a Hanwha WAVE-PRO / Professional Recording License activated for recording. For all primary and secondary (if present) egress locations.

c. Exterior / Garage Government Vehicle (GOV) Parking Cameras -https://hanwhavisionamerica.com/product/xnv-9083r/ and https://hanwhavisionamerica.com/product/xnp-c8253r/:

1. Two (2) plus cameras dedicated for each GOV parking area with optical zoom to provide adequate coverage of all GOVs.

2. One (1) plus XNV-9083R camera(s) use the varifocal lens to zoom in and cover entire GOV parking area.

3. One (1) plus XNP-C8253R (PTZ) PoE++ camera(s) to cover entire GOV parking area with AI person auto tracking enabled.

4. PoE++ (IEEE802.3bt, Class6, Type3z) Injector included with XNP-C8253R package. All

Injector(s) to be mounted on the Security Board.

d. General / Minimum Standards:

1. The appropriate quantity of cameras and Service viewing Monitors are to be installed (some specific sites may require more than quantities identified above).

2. Mounting of cameras to be at 12 feet above ground level, or as site requires.

3. Camera spacing not to exceed 40 feet between camera placements.

4. Camera must have appropriate viewing angle and mounted with no obstructions / blind spots.

Absolutely NO BLIND SPOTS allowed (exterior and interior common areas).

5. Camera images must provide 40PPF (pixel per foot) resolution at 25ft. Stored images MUST have a high enough quality to provide convictable resolution / identification of intruders, vandals, thieves, etc. when necessary.

8) CCTV / Security Signage: Install vandal resistant signage at the following locations:

a. Near exterior main entrance door(s) – Incorporated into the JRFC Graphic perforated window wraps in paragraph G.9.b.2. Or, installed over the top AFTER perforated window wraps are already installed.

b. Near exterior secondary exit door(s).

c. Minimum of one (1) CCTV / Security Warning parking sign at each GOV designated parking areas (typically strapped to light poles).

Signage Details:

1. Sign material to be aluminum and match the CCTV signage graphic below.

2. Minimum size of signage shall be equal to 8.5” H x 11” W.

9) Military Service Space: CCTV Display Monitors with Decoder:

a. Samsung DU8000 55” UHD LED Monitor: One (1) plus CCTV Display Monitors to be installed in each Military Service facility’s open office area for dedicated CCTV viewing, via the SPD-152 PoE decoder. Centered in open office area to allow maximum visibility by recruiters, minimize glare or bright sunlight (which reduces visibility). NOT to be mounted near exterior windows. Note:

Individual Military Service offices may require more than one monitor due to the large size / configuration of their area for adequate viewing.

b. Hanwha SPD-152, PoE Network Video Decoder: Decoder is a PoE device and can support two (2) monitors via HDMI cords (mounted on back of monitor).

c. Customized Video Feed Requirements: Installer to setup custom layout for each SPD-152 Video Decoder / Military Service office showing real time paths of egress, common areas, GOV’s and building perimeter of Government controlled space including (see CCTV / NVR System (Example Layouts Page

3) for Military Service Monitor(s) SPD-152 basic layout and standards below:

1. Interior egress door cameras (Military Service specific).

2. Exterior egress paths.

3. Common areas / hallways.

4. GOV parking.

10) Office Monitor Mounting Pole: Displays2Go mounting pole (telescoping pole sized for specific installation location, screen size and weight requirements, with 360° rotation and 25° tilting capable bracket):

https://www.displays2go.com/P-29667/Swivel-Ceiling-TV-Mount-Flat-Inclined-Surfaces

a. Installation: Pole mounted to understructure (through the drop ceiling tile) along with bracing / framing to support and minimal sway / movement. Location as identified on the approved floor plan / AE drawing.

b. Duplex outlet and communications outlet boxes (with CAT 6 Port) to be installed and concealed above ceiling tiles directly above monitor mounting location. Wiring to be routed thru / inside the mounting pole (power, ethernet wires, etc.).

c. Mounting height to be 8’-6” AFF for top edge of Military Service monitor(s). Monitor mounting poles to be rated for appropriate size and weight. If an obstruction prevents the installation of the monitors at the specified mounting height, the tolerance for installation is + / - 6”. Other mounting requirements:

1. Installation to include a “ceiling plate” or “ceiling mast trim ring” cover (to cover the hole for the pipe in the drop ceiling) and secured to the ceiling tile (may require additional support above the ceiling tile to prevent future ceiling tile sagging / damage). Color to match pole color.

2. Inside and outside wall corners to include the appropriate offset distance for tilting / rotating along all walls to allow maximum viewing adjustments.

IMPORTANT: If examples conflict with the specifications, the specifications always take precedence. Coordinate with the COE representative.

U.S. ARMY CORPS OF ENGINEERS

Recruiting Facilities Program

CCTV / NVR System ~ Page 2 of 4

CCTV / NVR System - (Example Layouts)

CCTV / NVR System ~ Page 3 of 4

CCTV / NVR System ~ Page 4 of 4