Attachment 1-1L Changes to Federal Standard 307AP Electric Veh.pdf
PDF 42 KB Posted
- Solicitation number
- QMAA-JC-100001-N
- Issued by
-
GSA Federal Acquisition Service
About this file
Vehicle Standards - Electric Vehicles
View the file
Other files
Show all 23
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Changes to Federal Standard 307AP
Electric Vehicles Revised 7 Dec 2010
Item 30E
Delete the existing verbiage and replace with the following:
The compact cargo van specified, shall be a plug in electric vehicle (EV), enclosed all-steel unitized, or on-frame constructed, integral body and cab.
The electric vehicle features include the following:
Top speed of 70 MPH
80 mile range on one full battery charge (chargeable from 120 or 240volt outlet-6 to 8 hours with 240 volt or 20 to 24 hours with 120 volt charging outlet)
The following features are NOT included:
Spare tire
Charging station
NOTE: The contractor shall be fully responsible for the bumper to bumper warranty of this completed vehicle including, but not limited to, the chassis, drive-train, all modifications.
Changes to the minimums:
RSC is a minimum requirement
GVWR is reduced to 5000
SAIB is changed to Head & Side Impact Airbags
STA is deleted
BDSZ is changed to 170-190
WB is reduced to 112
RRDR is changed to hinged
DRL is a minimum requirement
CR is a minimum requirement
Changes to the Features:
PAY is reduced to 1000
Item 134E
Delete the existing verbiage and replace with the following:
This forward-control, walk-in style vehicle shall have an integral driver's compartment and enclosed body and as specified. The standard commercial delivery van specified shall utilize a current model year chassis with all electric drive. This is an all electric truck with estimated range of 50-75 miles. The drive train is configured with a liquid cooled brushless motor and a Lithium Battery Pack.
There is an on-board 220V battery charger as a minimum.
The contractor is fully responsible for the bumper to bumper warranty of this completed vehicle including, but not limited to, the chassis, drive-train, fuel system and all modifications.
The requirements listed below shall be the minimum furnished on this vehicle:
1. The body shall be constructed of sheet aluminum or magnesium alloys of equal strength minimum 0.100 in side panels and with an aluminum frame or molded fiberglass.
2. The roof shall be supported by 4integral longitudinal ribsand metal roof reinforcements which are bonded in place on 24 in spacing front to rear.
3. The nose section of body and interior engine cover may be of composite construction. This shall provide access for all operator required engine and drive train service and maintenance.
4. Upholstered high back driver and assistant seats set on tilt pedestals shall be provided. Seats shall be adjustable fore, aft and for height, with positive locking device to secure seat in place when in use. Both seats shall be provided with3 point safety belts.
5. The cab compartment shall be furnished with a minimum 10,000 BTU rated heater.
6. Dome lights shall be provided: one in the driver's compartment and two in the cargo compartment, equally spaced.
7. Dual adjustable combination (flat and convex) swing away mirrors shall be furnished.
9. Side door steps shall be provided at both front entrances, and shall have a tread plate surface.
10. Body shall have sliding type front doors. The door operating handles shall be capable of serving as door opening/closing handles, or door grab handles shall be provided.
11. All doors shall be furnished with cylinder type locks for the same key, with unlike keys on vehicles to the same destination.
12. Sliding windows with not less than 360 sq in of clear glass shallbe provided in the front doors. All door windows shall be safety glass mounted in molded rubber (or equal) in the upper section of the doors. Windows shall be weather tight.
13. Rear door clear opening shall be a minimum of 35 in wide and 65 in high. Rear doors shall have anR38 door check with a 3 inch extension to hold door in full open position. Grab handle shall be provided on inside of rear door, in addition to door latch operating handle, to assist in closing door(s).
14. A full width, minimum7 inch deep safety-tread steel step shall be furnished.
15. The spare tire carrier shall be located in the cargo area directly behind the bulkhead on the driver’s sidewall.
16. Not less than five full width cross members (including end sills) shall be furnished. Stub cross members, as required at wheel housing to provide required strength, shall be furnished. Flooring with integrally formed cross members meets these requirements.
17. Roof shall be one piece center section with caps at the front, rear and sides, not less than 0.032 in thick aluminum or molded fiberglass. All body seams and joints shall be dust and weather sealed.
18. Cargo area floor shall be all aluminum ribbed floor planks. The cargo floor shall be not less than 0.125 in. The driver's area and steps shall be not less than 18gage
(0.0478 in).
19. Floor and support members shall sustain an evenly distributed load of 125 lb per sq ft of floor area. Alternate floor construction shall be of extruded aluminum, dryfreight construction with strength at least equal to that of steel.
White is the standard color for this item. If a color other than white is desired, option
"BPC" Body Paint Color must be ordered. Ordering option BPC requires that a color be chosen from the "Quantity and Color Selections" page in AUTOCHOICE.
Body Load Length, ft: 12
Body Load Height:, ft: 6
Body Interior Capacity Min, ft3: 550
Cargo Door Type: Center Panel Doors
Changes to the minimums:
WB is reduced to 135
HP is reduced to 100 hp/70 kw
TORQ is reduced to 200
Changes to the Features:
PAY is reduced to 4000
File details come from the government source that posted it. Updated .