MUAS for HC RFP Exhibit A CDRL A006 SDII DRAFT.pdf

DD FORM 1423-1, FEB 2001

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

PREVIOUS EDITION MAY BE USED.

The public reporting burden for this collection of information is estimated to average 110 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense, Executive Services (0704-0188). Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a of information if it does not display a currently valid OMB control number. Please do not return your form to the above organization. Send completed form to the Government Issuing Contracting Officer for the Contract/PR No. listed in Block E.

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

TDP ________ TM _______ OTHER

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

1. DATA ITEM NO. 2. TITLE OF DATA ITEM 3. SUBTITLE

4. AUTHORITY (Data Acquisition Document No.) 5. CONTRACT REFERENCE 6. REQUIRING OFFICE

7. DD 250 REQ

8. APP CODE

9. DIST STATEMENT

REQUIRED

10. FREQUENCY

11. AS OF DATE

12. DATE OF FIRST SUBMISSION

13. DATE OF SUBSEQUENT

SUBMISSION

14. DISTRIBUTION

a. ADDRESSEE

b. COPIES

Draft Final

Reg Repro

15. TOTAL

16. REMARKS

17. PRICE GROUP

18. ESTIMATED

TOTAL PRICE

G. PREPARED BY H. DATE I. APPROVED BY J. DATE

Page of Pages

A SDII

MUAS for Host Cutter TBD TBD

A006 CDRL System Design Installation Information SDII

RFP, Section L.5 USCG HQ CG-9313

A D (See BLK 16)

As required

Proposal

Proposal

As required

CG-9313 COR 1 1

1 1 0

DRAFT - Offerors must include a SDII in their proposal to demonstrate their approach to meeting the requirements depicted in the government Statement of Objectives and contractor's MUAS Performance Specification.

Offerors must provide an initial SDII with their response to facilitate the rapid integration into the vessel necessary to maintain program schedule. At a minimum, the Technical Data Plan (TDP) must have sufficient salient characteristics of the Contractor's proposed system to enable the USCG to determine the best means of integrating the system into the vessel.

At a minimum, the TDP must include the following:

1. Interface Design Description describing the interface characteristics of the system, the Hardware Configuration Items and the Computer Software Configuration Items.

2. Software Design Description describing the design of the Computer Software Configuration Item. The system software configuration must provide the version of the baseline software loaded and the various mission data files permissible for use.

3. The Contractor must provide a detailed equipment list specifying what equipment/ cabling the Contractor is providing and must identify what the Contractor is anticipating for the alteration installation team (AIT) to install and what equipment the contractor is planning on installing.

4. The Contractor must include any RF transmission requirements in the block diagram defining the RF transmission lines, transmit or receiver line type, connector types, and maximum length.

5. The Contractor must detail the connector part numbers and the wire types for all cables and external systems interfaces. The cables will be correlated with the interfaces identified in the system block diagram and with the connector designations.

6. The Contractor must detail the mechanical interfaces required including fully defining the form factors and physical equipment dimensions, mounting methods and all tolerances.

7. The Contractor must provide the power requirements for all applicable equipment. The power requirements must include operating environment constraints including maximum power use limits, momentary power interruption operation and the grounding and bonding requirements.

8. Electromagnetic characteristics of all emitters and receivers.

9. Technical manuals for all equipment being installed aboard the vessel.

10. Customized technical manuals or drawings specific or incidental to system installation on each HC.

11. New and modified product and developmental design drawings.

12. Safety data and documentation.

13. The Contractor must assist AIT with making final connections of contractor equipment and ship cabling.

Adobe Professional 8.0

CONTRACT DATA REQUIREMENTS LIST

(1 Data Item)

A. CONTRACT LINE ITEM NO. B. EXHIBIT C. CATEGORY:

TDP ________ TM _______ OTHER

D. SYSTEM/ITEM E. CONTRACT/PR NO. F. CONTRACTOR

16. REMARKS (Continued)

DD FORM 1423-1, FEB 2001 Page of Pages

A SDII

MUAS for Host Cutter TBD TBD

14. Provide information below for each antenna system to include Parameter and Source:

Required Coverage (Azimuth, Elevation) Radome size Antenna size Main Beam gain Side lobe gain Polarization Beam width (H: and V:

Movement Range Transmitter Specific Characteristics Peak output power Duty factor or average power (if applicable) Frequency range Bandwidth Spurious Emissions and Broadband Noise Modulation Harmonics and Intermodulation Distortion RF Filter Receiver Specific Characteristics Sensitivity Frequency range Bandwidth Spurious Response Image Response Burnout Threshold Receiver Selectivity Noise Figure RF Filter Modulation Data Rate

15. Maximum distance between Below Deck Equipment (BDE) and Above Deck Equipment (ADE)

16. Any distance restrictions between any amplifiers and antennas.

17. Any issues wih installing amplifiers above deck.

18. Has your systems been tested to MIL-STD-461 and MIL-STD-464? If so, then please provide test report.

19. Measured or modeled antenna patterns.

20. Sweeps of the front-end RF equipment.

21. Detailed drawings to include installation details, system interconnection diagrams, and RF Signal flow diagrams.

22. Technical manual or system specifications.

BLK 09:

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO USCG/DOD AND THEIR CONTRACTORS ONLY DUE TO CRITICAL TECHNOLOGY (28 JUN 2023). OTHER REQUESTS SHALL BE REFERRED TO COMMANDANT (CG-9313).

INSTRUCTIONS FOR COMPLETING DD FORM 1423

(See DoD 5010.12-M for detailed instructions.)

FOR GOVERNMENT PERSONNEL

Item A. Self-explanatory.

Item B. Self-explanatory.

Item C. Mark (X) appropriate category: TDP - Technical Data Package;

TM - Technical Manual; Other - other category of data, such as "Provisioning,""Configuration Management," etc.

Item D. Enter name of system/item being acquired that data will support.

Item E. Self-explanatory (to be filled in after contract award).

Item F. Self-explanatory (to be filled in after contract award).

Item G. Signature of preparer of CDRL.

Item H. Date CDRL was prepared.

Item I. Signature of CDRL approval authority.

Item J. Date CDRL was approved.

Item 1. See DoD FAR Supplement Subpart 4.71 for proper numbering.

Item 2. Enter title as it appears on data acquisition document cited in Item 4.

Item 3. Enter subtitle of data item for further definition of data item (optional entry).

Item 4. Enter Data Item Description (DID) number, military specification number, or military standard number listed in DoD 5010.12-L (AMSDL), or one-time DID number, that defines data content and format requirements.

Item 5. Enter reference to tasking in contract that generates requirement for the data item (e.g., Statement of Work paragraph number).

Item 6. Enter technical office responsible for ensuring adequacy of the data item.

Item 7. Specify requirement for inspection/acceptance of the data item by the Government.

Item 8. Specify requirement for approval of a draft before preparation of the final data item.

Item 9. For technical data, specify requirement for contractor to mark the appropriate distribution statement on the data (ref. DoDD 5230.24).

Item 10. Specify number of times data items are to be delivered.

Item 11. Specify as-of date of data item, when applicable.

Item 12. Specify when first submittal is required.

Item 13. Specify when subsequent submittals are required, when applicable.

Item 14. Enter addressees and number of draft/final copies to be delivered to each addressee. Explain reproducible copies in Item 16.

Item 15. Enter total number of draft/final copies to be delivered.

Item 16. Use for additional/clarifying information for Items 1 through 15.

Examples are: Tailoring of documents cited in Item 4; Clarification of submittal dates in Items 12 and 13; Explanation of reproducible copies in Item 14.; Desired medium for delivery of the data item.

FOR THE CONTRACTOR

Item 17. Specify appropriate price group from one of the following groups of effort in developing estimated prices for each data item listed on the DD Form 1423.

a. Group I. Definition - Data which is not otherwise essential to the contractor's performance of the primary contracted effort (production, development, testing, and administration) but which is required by DD Form 1423.

Estimated Price - Costs to be included under Group I are those applicable to preparing and assembling the data item in conformance with Government requirements, and the administration and other expenses related to reproducing and delivering such data items to the Government.

b. Group II. Definition - Data which is essential to the performance of the primary contracted effort but the contractor is required to perform additional work to conform to Government requirements with regard to depth of content, format, frequency of submittal, preparation, control, or quality of the data item.

Estimated Price - Costs to be included under Group II are those incurred over and above the cost of the essential data item without conforming to Government requirements, and the administrative and other expenses related to reproducing and delivering such data item to the Government.

c. Group III. Definition - Data which the contractor must develop for his internal use in performance of the primary contracted effort and does not require any substantial change to conform to Government requirements with regard to depth of content, format, frequency of submittal, preparation, control, and quality of the data item.

Estimated Price - Costs to be included under Group III are the administrative and other expenses related to reproducing and delivering such data item to the Government.

d. Group IV. Definition - Data which is developed by the contractor as part of his normal operating procedures and his effort in supplying these data to the Government is minimal.

Estimated Price - Group IV items should normally be shown on the DD Form 1423 at no cost.

Item 18. For each data item, enter an amount equal to that portion of the total price which is estimated to be attributable to the production or development for the Government of that item of data.

These estimated data prices shall be developed only from those costs which will be incurred as a direct result of the requirement to supply the data, over and above those costs which would otherwise be incurred in performance of the contract if no data were required. The estimated data prices shall not include any amount for rights in data. The Government's right to use the data shall be governed by the pertinent provisions of the contract.

DD FORM 1423-1 (BACK), FEB 2001