Att_2_PS_for_SRS_Rev_2.pdf

PERFORMANCE SPECIFICATION (PS)

FOR THE

SYNCHRO RESOLVER KIT

FOR THE

AN/USM-657B(V)2

Prepared by

PRODUCT MANAGER

TEST, MEASUREMENT, AND DIAGNOSTIC EQUIPMENT (TMDE)

MARINE CORPS SYSTEM COMMAND

PERFORMANCE SPECIFICATION

For

SYNCHRO RESOLVER INSTRUMENT

For

AN/USM-657B(V)2

INTRODUCTION:

The Product Manager for Test Measurement and Diagnostic Equipment (PdM-TMDE) has a requirement to provide a general purpose automatic test capability to the Fleet Marine Forces.

This synchro resolver procurement will allow the AN/USM-657(V)2, Third Echelon Test System

(TETS) to support the Light Armored Vehicle-25 (LAV-25) using the AN/PSM-123 Application

Program Set (APS). Currently, this APS can only be executed on the AN/USM-717, Virtual

Instrument Portable Electronic Repair Tester (VIPER/T) limiting its availability to the Fleet

Marine Force to maintain the LAV-25.

1. SCOPE.

This Performance Specification (PS) identifies the requirement of the selected instrument to meet the capabilities of a synchro resolver capable of supporting the AN/PSM-123 APS on the

AN/USM-657B(V)2.

The Contractor shall provide program management, systems engineering management, configuration management, quality assurance, and logistics planning and support.

A reference to the Government within this PS refers to the Marine Corps Systems Command, PM TMDE, CODE PMM-115, 2200 LESTER STREET, QUANTICO VA 22134-6050.

2. APPLICABLE DOCUMENTS.

The following documents, of the exact date and issue specified form a part of this PS to the extent specified herein. In the event of conflict between the applicable documents and this PS, the PS shall take precedence. However, nothing in this document supersedes applicable laws and regulations unless a specific exemption has been obtained.

Government:

Virtual Instrument Portable Equipment Repair Tester

(VIPER/T) Specification, AN/USM-717(V)

Block Upgrade Synchro Resolver Simulator Retrofit Kit Document

MIL-PRF-28800F Test Equipment For Use With Electrical and Electronic Equipment, General Specification For

AN/PSM-123 Application Program Set, LAV-25A2

3. REQUIREMENTS.

3.1 General. The work provided by the Contractor shall be performed in accordance with this

PS.

3.1.1 The contractor shall provide a synchro resolver capable of providing single and multi-speed generation.

3.1.2 The contractor shall provide a synchro resolver capable of providing single and multi-speed measurements.

3.1.3 The contractor shall provide a synchro resolver with 2 measurement channels.

3.1.4 The contractor shall provide a synchro resolver with 2 stimulus channels.

3.1.5 The contractor shall provide a synchro resolver with 1 reference channel.

3.1.6 The contractor shall provide a synchro resolver capable of generating an angular programmable range from 0 to 359.999° with a resolution of 0.001°.

3.1.6.1 The contractor shall provide a synchro resolver with a resolver mode capable of providing a line-to-line output of 1V to 90V programmable with an accuracy of

+/- .005 Degrees 360 Hz to 800 Hz and +/- 0.010 Degrees >800 Hz to 2000 Hz.

3.1.6.2 The contractor shall provide a synchro resolver with a synchro mode capable of providing a line-to-line output of 1V to 90V programmable with an accuracy of +/- .012

Degrees 47 Hz to 100 Hz and +/- .005 Degrees >100 Hz to 800 Hz.

3.1.7.1 The contractor shall provide a synchro resolver with a line-to–line output of 1V to 90V, programmable.

3.1.8 The proposed replacement shall be integrated into the latest version of the AN/USM- 657B(V)2 system software.

3.1.9 The proposed replacement shall function in an automated and stand-alone instrument mode.

3.1.10 The proposed replacement instrument shall have a graphical users interface (GUI) available to any user login and conform to the General Notes For Virtual Instrument GUIs document.

3.1.11 The proposed replacement shall be fully incorporated into the AN/USM-657B(V)2’s calibration and system self test programs.

4. QUALITY ASSURANCE PROVISIONS

4.1 Inspection and Tests

4.1.1 Responsibility for Inspection. The contractor shall provide and maintain an inspection program which will assure that all supplies and services conform to the contract requirements whether manufactured or processed by the contractor, or procured from subcontractors or vendors. The contractor's inspection system shall be provided in their proposal and will be evaluated by the Government. Except as otherwise specified herein, the contractor may use his own facility or any commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the PS when such inspections are deemed necessary to assure supplies and services conform to prescribed requirements.

4.1.2 Responsibility for Compliance. All items shall meet the requirements of Section 3 of this

PS. The inspections set forth in this PS shall become a part of the contractor's overall inspection system or quality assurance program.

4.2 Inspection Methods. Each SRS shall be subjected to contractor inspection and certification to ensure the proper functioning of equipment, including all operator controls, and conformance with safety requirements. The inspection requirements specified herein are identified as follows:

3 Feb 2014

ITEM

3.0

REQUIREMENT

4.0

COMPLIANCE

REFERENCE

PROD

ACC

I T D

1 3.1 4.2 N/A X

2 3.1.1 4.2 MIL-PRF-28800F ¶ 4.4.1 X

3 3.1.2 4.2 MIL-PRF-28800F ¶ 4.4.1

X

4 3.1.3 4.2 MIL-PRF-28800F ¶ 4.4.1

5 3.1.4 4.2 MIL-PRF-28800F ¶ 4.4.1

6 3.1.5 4.2 MIL-PRF-28800F ¶ 4.4.1

X

7 3.1.6 4.2 MIL-PRF-28800F ¶ 4.4.1

X

8 3.1.6.1 4.2 MIL-PRF-28800F ¶ 4.4.1

X

9 3.1.6.2 4.2 MIL-PRF-28800F ¶ 4.4.1 X

10 3.1.7 4.2 MIL-PRF-28800F ¶ 4.4.1 X

11 3.1.7.1 4.2 MIL-PRF-28800F ¶ 4.4.1

X

12 3.1.8 4.2 Run system self-test and stand alone instrument software X

13 3.1.9

4.2 Run system self-test and stand alone

instrument software X

14 3.1.10 4.2 Run system self-test and stand alone instrument software X

15 3.1.11 4.2 Run system self-test and stand alone instrument software

I – Inspection

T - Test

D – Demonstration