Attachment_06_MSDS_Sheets.pdf

lieF.InOfl ~4stfs’0vig metco Safety Data Sheet Metco 101, lOiNS, 1O1BNS, 101SF, IO1FP, Metcolite 14, C, F, F36, yE, Amdry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, Amdry XPT W631, GRIT BLAST MATERIAL 0.4-0.8MM, GRIT BLASTING MATERIAL G-24, PT-1100, XPT DH 1079, AE 9503, AE 9795

Section 1. Product and company identification Product name : Metco 101, lOiNS, 1O1BNS, 101SF, 1O1FP, Metcolite 14, C, F, F36, VF, Amdry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, Amdry XPT W631, GRIT BLAST MATERIAL 0.4-0.8MM, GRIT BLASTING MATERIAL

G-24, PT-1100, XPT DH 1079, AE 9503, AE 9795

Material uses : Metal industry: Used by spraying Supplier : Oerlikon Metco (US) Inc.

1101 Prospect Avenue Westbury, NY 11590

Telephone no. : (516) 334-1300 (7:30AM - 4:00PM) In case of emeraency : CHEMTREC: 800-424-9300 Calls Outside the United : +1 703-741-5970: (USA) 24 hour Chemtrec International Emergency Response States Service Product type : Powder.

Section 2. Hazards identification OSHAIHCS status : While this material is not considered hazardous by the OSHA Hazard Communication

Standard (29 CFR 1910.1200), this SDS contains valuable information critical to the safe handling and proper use of the product. This SDS should be retained and available for employees and other users of this product.

Classification of the : Not classified.

substance or mixture

GHS label elements Signal word : No signal word.

Hazard statements : No known significant effects or critical hazards.

Precautionary statements Prevention : Not applicable.

Response : Not applicable.

Storage Not applicable.

Disposal : Not applicable.

Hazards not otherwise : Handling and/or processing of this material may generate a dust which can cause classified mechanical irritation of the eyes, skin, nose and throat.

Date of issue SDS # Prepared by Pa e’ 1/11 08/18/2015 50-134 Oerlikon Metco g

Metco 101, lOINS, 1OIBNS, 101SF, 101FF’, Metcolite 14, C, F, P36, VF, Amelry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, AmdryXPT W631, GRIT BLASTMA TERIAL 0.4-0.8MM, GRIT

BLASTING MA TERIAL G-24, PT-1100, XPT DH 1079, AE 9503, AE 9795

Section 3.. Compositionlinformation on ingredients

United States

Ingredient name % CAS number aluminium oxide 95 1344-28-1 titanium dioxide 3 13463-67-7 dhron trioxide 1 1 309-37-1 silicon dioxide 1 7631-86-9

Mexico Classification

Name GAS UN number IDLK H F R Special number aluminium oxide 1344-28-1 Not 95 - 0 0 0 -regulated titanium dioxide 1 3463-67-7 Not 3 5000 mg/rn3 2 0 0 -regulated dNron trioxide 1309-37-1 Not 1 2500 mg/rn3 2 0 0 -regulated silicon dioxide 7631-86-9 Not 1 3000 mg/rn3 1 0 0 -regulated Any concentration shown as a range is to protect confidentiality or is due to batch variation.

There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.

Occupational exposure limits, if available, are listed in Section 8.

Radionuclides: This product contains trace quantities of naturally occurring radioactive material: Uranium - 238 and Thorium - 232 (Source Material). The concentration of Source Material is less than 0.05% by weight. The total activity of Source Material is less than 3.5 Sq/gram. Check local regulations to determine if a site-specific dose assessment is required.

Section 4. First aid measures

Description of necessary first aid measures Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Get medical attention if irritation occurs.

Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing. Get medical attention if symptoms occur.

Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur.

Ingestion : Wash out mouth with water. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Do not induce vomiting unless directed to do so by medical personnel. Get medical attention if symptoms occur.

Most important svmptomsleffects. acute and delayed Potential acute health effects

Eye contact : Exposure to airborne concentrations above statutory or recommended exposure limits may cause irritation of the eyes.

Inhalation : Exposure to airborne concentrations above statutory or recommended exposure limits may cause irritation of the nose, throat and lungs.

Date of issue SDS # Prepared by Pa r 2/11 08/18/2015 50-134 Qerlikon Metco g

Metco 101, lOINS, IOIBNS, 101SF, IOIFP, Metcolite 14, C, F, P36, VF, Amdry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, Amdry XPT W631, GRIT BLAST MATERIAL 0.4-0.8MM, GRIT

BLASTING MA TERIAL G-24, PT-I 100, XPT DH 1079, AE 9503, AE 9795

Section 4. First aid measures Skin contact : No known significant effects or critical hazards.

Ingestion No known significant effects or critical hazards.

Over-exposure siqnslsymptoms Eye contact Adverse symptoms may include the following:

irritation redness

Inhalation : Adverse symptoms may include the following:

respiratory tract irritation coughing

Skin contact : No specific data.

Ingestion : No specific data.

Indication of immediate medical attention and special treatment needed, if necessary Notes to physician Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.

Specific treatments No specific treatment.

Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training.

See toxicological information (Section 11)

Section 5. Fire-fighting measures

Extinguishing media Suitable extinguishing : Use extinguishing media suitable for surrounding materials.

media Unsuitable extinguishing : None known.

media

Specific hazards arising : No specific fire or explosion hazard.

from the chemical Hazardous thermal Decomposition products may include the following materials:

decomposition products Metal.

Dust and fumes.

Special protective actions : Promptly isolate the scene by removing all persons from the vicinity of the incident if for fire-fighters there is a fire. No action shall be taken involving any personal risk or without suitable training.

Special protective : Fire-fighters should wear appropriate protective equipment and self-contained breathing equipment for fire4ighters apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Section 6. Accidental release measures

Personal precautions. Drotective equipment and emergency procedures For non-emergency : No action shall be taken involving any personal risk or without suitable training.

personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing dust Put on appropriate personal protective equipment.

Date of issue SDS # Prepared by Pa r 3/11

Metco 101, lOINS, IOIRNS, 101SF, I0IFP, Metcolite 14, C, F, F36, VF, Amdry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, Amc’ry XPT W631, GRIT BLASTMA TERIAL 0.4-0.8MM, GRIT

BLASTING MA TERIAL G..24, PT-1100, XPT DH 1079, AE 9503, AE 9795

Section 6. Accidental release measures For emergency responders : If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in “For non-emergency personnel’.

Environmental precautions Avoid dispersal of spilled material and runoff and cobtact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).

Methods and materials for containment and cleaning up Small spill Move containers from spill area. Vacuum or sweep up material and place in a designated, labeled waste container. Dispose of via a licensed waste disposal contractor.

Large spill Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Vacuum or sweep up material and place in a designated, labeled waste container. Avoid creating dusty conditions and prevent wind dispersal. Dispose of via a licensed waste disposal contractor. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.

Section 7. Handling and storage Precautions for safe handling Protective measures Put on appropriate personal protective equipment (see Section 8). Avoid breathing dust.

Advice on general Eating, drinking and smoking should be prohibited in areas where this material is occupational hygiene handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures.

Conditions for safe : Store in accordance with local regulations. Store in original container protected from storage, including any direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials incompatibilities (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate container to avoid environmental contamination.

Section 8. Exposure controls/personal protection

Control parameters United States Occupational exposure limits

Ingredient name Exposure limits aluminium oxide ACGIH TLV (United States, 412014).

TWA: 1 mg/rn3 8 hours. Form: Respirable fraction

• OSHA PEL (United States, 212013).

TWA: 5 mg/rn3 8 hours. Form: Respirable fraction TWA: 15 mg/m3 8 hours. Form: Total dust titanium dioxide OSHA PEL (United States, 212013).

TWA: 15 mg/m3 8 hours. Form: Total dust

ACGIH TLV (United States, 412014).

. TWA: 10 mg/m3 8 hours.

diiron trioxide ACGIK TLV (United States, 412014).

TWA: 5 mg/m3 8 hours. Form: Respirable fraction

OSHA PEL (United States, 212013).

Date of issue SDS # Prepared by 08/18/2015 50-1 34 Oerlikon Metco Page: 4/11

Metco 101, lOINS, IOIBNS, 101SF, IOIFP, Metcolite 14, C, F, F36, VF, Amclry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, Amdry XPT W631, GRIT BLAST MATERIAL 0.4-0.8MM, GRIT

BLASTING MATERIAL 0-24, PT-1100, XPTDH 1079, AE 9503, AE 9795

Section 8. Exposure controls/personal protection

TWA: 10 mg/rn3 8 hours.

silicon dioxide -

Mexico Occupational exnosure limits

Ingredient name Exposure limits aluminium oxide NOM-010-STPS (Mexico, 912000).

. LMPE-PPT: 10 mg/rn3 8 hours.

titanium dioxide NOM-010-STPS (Mexico, 9/2000).

. LMPE-CT: 20 mg/rn3, (as Ti) 15 minutes.

LMPE-PPT: 10 mg/rn31 (as Ti) 8 hours.

diiron trioxide NOM-Ol 0-STPS (Mexico, 912000).

LMPE-CT: 10 mg/rn3, (as Fe) 15 minutes.

LMPE-PPT: 5 mg/m3, (as Fe) 8 hours.

silicon dioxide NOM-010-STPS (Mexico, 912000).

LMPE-PPT: 3 mg/rn3 8 hours. Form: breathable particulates LMPE-PPT: 10 mg/rn3 8 hours. Form: inhalable particulates

Appropriate engineering controls

Environmental exposure controls

Use only with adequate ventilation. If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits.

Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.

Individual Drotectign measures Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.

Appropriate techniques should be used to remove potentially contaminated clothing.

Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.

If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side-shields. If operating conditions cause high dust concentrations to be produced, use dust goggles. Safety glasses or goggles are recommended when handling this material. During the thermal spray process, safety goggles and dark lenses must be worn. Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts.

Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Rubber or other appropriate gloves should be worn to minimize contact.

For hygienic reasons rubber gloves should not be worn for more than 2 hours. During the thermal spray process, heat insulated gloves are recommended.

Body protection : Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product

Hygiene measures

Eyelface protection

Skin protection Hand protection

Date of issue 08/18/2015

SDS #

50-1 34

Prepared by Qerlikon Metco Page: 5/11

Metco 101, lOINS, 101BI’JS, 101SF, IOIFP, Metcolite 14, C, F, F36, VF, Amdry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, Amdry XPT W631, GRIT BLAST MA TERIAL 0.4-0.8MM, GRIT

BLASTING MA TERIAL 0-24, PT-I 100, XPT DH 1079, AE 9503, AE 9795

Section 8. Exposure Other skin protection

Respiratory protection

Hearing Protection

Protective Clothing (Pictograms) controls/personal protection Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.

Use a properly fitted, particulate filter respirator complying with an approved standard if a risk assessment indicates this is necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator.

Hearing protection that meets local standards should be used. During the thermal spray process, the operator and other personnel close to the spray operation must be protected from excessive noise.fl

Section 9. Physical and chemical properties

Solid. [Powder.] Gray.

Odorless.

Not available.

Not applicable.

Not available.

Not available.

Not applicable.

Not applicable.

Non-flammable in the presence of the following materials or conditions: open flames sparks and static discharge and shocks and mechanical impacts.

Not available.

Not applicable.

Not applicable.

3.9 [Specific gravity] Insoluble in the following materials: cold water.

Not applicable.

Not available.

Not available.

Not applicable.

ApDearance Physical state Color Odor Odor threshold pH Melting point Boiling point Flash point Evaporation rate Flammability (solid, gas)

Lower and upper explosive (flammable) limits Vapor pressure Vapor density Relative density Solubility Partition coefficient: n octanollwater Auto-ignition temperature Decomposition temperature Viscosity

Date of issue 08/18/2015

SDS #

50-1 34

Prepared by Oerlikon Metco Page: 6/11

Metco 101, lOINS, IOIBNS, 101SF, IOIFP, Metcolite 14, C, F, F36, VF, Amdry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, AmcfryXPT W631, GRIT BLAST MATERIAL 0.4-0.8MM, GRIT

BLASTING MATERIAL G-24, PT-1100, XPTDH 1079, AE 9503, AE 9795

Section 10. Stability and reactivity Reactivity : No specific test data related to reactivity available for this product or its ingredients.

Chemical stability : The product is stable.

Possibility of hazardous Under normal conditions of storage and use, hazardous reactions will not occur.

reactions

Conditions to avoid Store in a cool dry place away from incompatible materials.

Incompatible materials : Strong acids alkalines

Hazardous decomposition Under normal conditions of storage and use, hazardous decomposition products should products not be produced.

Section 11. Toxicological information

Information on toxicological effects Acute toxicity Not available.

Irritation!Corrosipn Not available.

Sensitization Not available.

Mutagenicity Not available.

Cprcinogenicitv Not available.

ReDroductive toxicity Not available.

Teratogenicity Not available.

Specific target oraan toxicity (single exDosure) Not available.

Specific target organ toxicity (repeated exposure) Not available.

Aspiration hazard Not available.

Information on the likely : Routes of entry anticipated: Oral, Dermal, Inhalation.

routes of exposure

Potential acute health effects Eye contact : Exposure to airborne concentrations above statutory or recommended exposure limits may cause irritation of the eyes.

08/18/2015 50-134 Qerlikon Metco Page: 7/11

Metco 101, lOINS, IOIBNS, 101SF, IOIFP, Metcolite 14, C, F, F36, VF, Amdry 187, 6200, 6202; 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, AmdryXPT W631, GRIT BLAST MATERIAL 0.4-0.8MM, GRIT

BLASTING MATERIAL G-24, PT-1100, XPTDH 1079, AE 9503, AE 9795

Section 11. Toxicological information Inhalation Exposure to airborne concentrations above statutory or recommended exposure limits may cause irritation of the nose, throat and lungs.

Skin contact No known significant effects or critical hazards.

Ingestion No known significant effects or critical hazards.

SvmDtoms related to the Dhvsical. chemical and toxicological characteristics Eye contact : Adverse symptoms may include the following:

irritation redness

Inhalation Adverse symptoms may includethe following:

respiratory tract irritation coughing

Skin contact : No specific data.

Ingestion No specific data.

Delayed and immediate effects and also chronic effects from short and long term exDosure Short term exoosure

Potential immediate : Not available.

effects Potential delayed effects : Not available.

Lona term exposure Potential immediate Not available.

effects Potential delayed effects : Not available.

Potential chronic health effects Not available.

ConclusionlSummary Not available.

General : Repeated or prolonged inhalation of dust may lead to chronic respiratory irritation.

Carcinogenicity : No known significant effects or critical hazards.

Mutagenicity No known significant effects or critical hazards.

Teratogenicity : No known significant effects or critical hazards.

Developmental effects : No known significant effects or critical hazards.

Fertility effects No known significant effects or critical hazards.

Section 12. Ecological information

Toxicity Not available.

Persistence and degradability Not available.

Bioaccumulatiye ootential

Date of issue SDS # Prepared by Pa e~ 8/11 08/18/2015 50-134 Oerlikon Metco

Metco 101, lOINS, IOIBMS, 101SF, 101FF, Metcolite 14, C, F, F36, VF, Amdry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, AmdryXPT W631, GRIT BLAST MATERIAL 0.4-0.8MM, GRIT

BLASTING MATERIAL 0-24, PT-I 100, XPT DH 1079, AE 9503, AE 9795

Section 12. Ecological information Not available.

Mobility in soil Soillwater partition Not available.

coefficient (Koc)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction.

Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.

Section 14. Transport information

DOT TDG Mexico ADRIRID IMDG IATA Classification Classification Classification

UN number Not regulated Not regulated Not regulated Not regulated Not regulated Not regulated

UNproper - - - - - -shipping name

Transport - - - - - -hazard class(es)

Packing group - - - - - -

Environmental No. No. No. No. No. No.

hazards

Additional - - - - - -information

Special precautions for user : Transport within user’s premises: always transport in closed containers that are

• upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage.

Page: 9/1108/18/2015 50-134 Qerlikon Metco

Metco 101, lOINS, IOIBNS, 101SF, IOIFP, Metcolite 14, C, F, F36, VF, Amdry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, Amdry XPT W631, GRIT BLASTMA TERIAL 0.4-0.8MM, GRIT

BLASTING MATERIAL G-24, PT-1100, XPTDH 1079, AE 9503, AE 9795

Section 15. Regulatory information

U.S. Federal regulations : TSCA 8(a) CDR ExemptlPartial exemption: Not determined All components are listed or exempted.

Clean AirAct Section 112 : Not listed

(b) Hazardous Air Pollutants (HAPs) Clean Air Act Section 602 : Not listed Class I Substances

Clean Air Act Section 602 : Not listed Class II Substances

DEA List I Chemicals : Not listed (Precursor Chemicals)

DEA List II Chemicals : Not listed (Essential Chemicals)

SARA 3021304

ComDositipnlinformation on ingredients

No products were found.

SARA 304 RQ : Not applicable.

SARA 3111312

Classification : Not applicable.

Cpmppsitionlinformatipn on ingredients

No products were found.

SARA 313

Product name CAS number Y0

Form R - Reporting aluminium oxide 1344-28-1 95 requirements

Supplier notification aluminium oxide 1344-28-1 95

SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.

State regulations Massachusetts The following components are listed: ALUMINUM OXIDE; TITANIUM DIOXIDE; IRON

OXIDE DUST; AMORPHOUS SILICA

New York : None of the components are listed.

New Jersey : The following components are listed: ALUMINUM OXIDE; alpha-ALUMINA; TITANIUM

DIOXIDE; TITANIUM OXIDE (TiO2); IRON OXIDE; FERRIC OXIDE Pennsylvania The following components are listed: ALUMINUM OXIDE (AL2O3); TITANIUM OXIDE

(T102); IRON OXIDE (FE2O3); SILICA

California Prop. 65

WARNING: This product contains a chemical known to the State of California to cause cancer.

Date of issue SDS # Prepared by Pa e~ 10/11

Metco 101, lOINS, IOIBNS, 101SF, IOIFP, Metcolite 14, C, F, F36, VF, Amelry 187, 6200, 6202, 6203, 6204, 6208, PEM 10-231, Metco 6203, XPT-D 705, 644, PT 1100, AmdryXPT W631, GRIT BLASTMA TERIAL 0.4-0.8MM, GRIT

BLASTING MATERIAL G-24, PT-1100, XPTDH 1079. AE 9503. AE 9795

Section 15. Regulatory information

Ingredient name titanium dioxide Yes. No. No. No.

Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright ©1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.

Copyright ©2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.

History

Cancer Reproductive No significant risk level

Maximum acceptable dosage level

Date of issue/Date of revision Version

Key to abbreviations

Notice to reader

:3

To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein.

Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.

Date of issue 08/1812015

Prepared by Qerlikon Metco

Section 16. Other information

National Fire Protection Association U.S.A.)

Flammability

Health lnstabilitylReactivity

Special

08/18/2015.

ATE = Acute Toxicity Estimate BCE = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL 73/78 = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. (“Marpol” = marine pollution) UN = United Nations

SDS #

50-1 34 Page: 11/11