LUTRON_Diva_Controls_and_Cover_Plates_Spec_Sheets.pdf

The designer dimmer that matches your paddle switches.

PRODUCT FAMILY FEATURES

• Large paddle switch with a captive linear-slide dimmer for a standard designer wallplate opening

• Full family of products for most lighting sources

• Dimmers feature built-in soft-glow nightlight

• Uses standard single-pole and 3-way wiring for easy installation in any home

• For more Diva choices, see the new Diva Satin Colors product line

DIMENSIONS

Front Profile

SPECIFICATION SUBMITTAL

CONTROLS AND ACCESSORIES

Preset Fan-Speed Switches Dimmers Controls

Have Questions? Call the Lutron Hotline 800-523-9466 To order—Call Lutron Customer Service 610-282-3800

JOB NAME AREA CONTROLLED

LOCATION JOB NUMBER

TITLE PAGE NO.

SPECIFICATION SERIES

STANDARD FEATURES

• Square Law Dimming • RFI suppression

• Power-failure memory • Captive linear slider

• Electrostatic discharge tested • Precise color matching

• Mechanical air-gap switch to disconnect load power Lutron controls are rated at 120VAC, 60Hz unless otherwise noted.

Controls www.lutron.com/diva

Soft glow nightlight

Select light level with slider

Switch on to selected light level/off

Preset Dimmer

Preset Fan-Speed Controls

1.31" * (33mm)

2.75" (70mm)

2.94" (75mm)

4.69" (119mm)

0.30" (7.6mm)

* some models up to 1.44" (37mm)

Select fan speed with slider

Switch on to selected fan speed/off

Cable TV Jack

Single Telephone Jack

15A Receptacle

15A GFCI Receptacle

2-gang to 6-gang wallplates

Telephone/Cable TV Jacks

Standard Multigang Wallplates

Receptacles

Ports

6-Port Frame

Maximum Description Capacity 1 Model #

HI-POWER 2•4•6TM DIMMING MODULES

To increase load capacity up to 30,000W/VA in most popular sources, use one DV-600P- or DV-603P- and add up to five dimming modules. Cannot be used with 0-10VDC ballast.

FAN-SPEED CONTROLS

Quiet Controls

For use with one ceiling paddle fan.

Preset Fan-Speed Controls 3

Single pole/ 3-way, 1.5A DVFSQ-F- 3-speed Note: Does not have soft-glow nightlight. For 3-way and 4-way switching, use with Claro switches or other mechanical switches.

SWITCHES 3

General Purpose Switching of all Sources and Motor Loads

Single pole, 120/277V 15A CA-1PSH- 3-way, 120/277V 15A CA-3PSH- 4-way, 120/277V 15A CA-4PSH-

ACCESSORIES

Receptacles

Receptacle 3

15A, 125V CAR-15H-

GFCI Receptacle 3

15A, 125V CAR-15-GFCIH-

Telephone and Cable Television Jacks

A physical barrier (partition) must exist when ganging with line-voltage products Single Telephone Jack 4

6-conductor, RJ11 CA-PJH- Note: Also accepts most 4-conductor plugs.

Cable TV Jack 3, 4

F-STYLE

75-Ohm, coaxial cable jack CA-CJH-

Have Questions? Call the Lutron Hotline 800-523-9466 To order—Call Lutron Customer Service 610-282-3800

Maximum Description Capacity 1 Model #

DIMMERS

Incandescent

Preset Dimmers with Nightlight Single pole 600W DV-600P- Single pole 1000W DV-10P- 3-way 600W DV-603P- 3-way 1000W DV-103P- Note: The nightlight is visible best on the lighter colors. For 3-way and 4-way switching, use with Claro® switches or other mechanical switches.

Electronic Low Voltage

Preset Dimmers with Nightlight Single pole 300W DVELV-300P- 3-way 300W DVELV-303P- Note: Requires neutral wire connection. The nightlight is visible best on the lighter colors. For 3-way and 4-way switching, use with Claro switches or other mechanical switches.

Magnetic Low Voltage

Preset Dimmers with Nightlight Single pole 600VA (450W 2) DVLV-600P- Single pole 1000VA (800W 2) DVLV-10P- 3-way 600VA (450W 2) DVLV-603P- 3-way 1000VA (800W 2) DVLV-103P- Note: The nightlight is visible best on the lighter colors. For 3-way and 4-way switching, use with Claro switches or other mechanical switches.

Fluorescent Dimming with Hi-lume® and Eco-10TM (ECO-Series) Electronic Ballasts

Preset Dimmers with Nightlight 3

Single pole/ 3-way 8A DVF-103P- Single pole/ 3-way, 277V 6A DVF-103P-277- Note: Use with Lutron Hi-lume or Eco-10 (ECO-Series) line voltage control Electronic Dimming Ballasts only. Requires neutral wire connection. The nightlight is visible best on the lighter colors. For 3-way and 4-way switching, use with Claro switches or other mechanical switches.

Fluorescent Dimming with Tu-Wire®

Electronic Ballasts

Preset Dimmers with Nightlight Single pole/ 3-way 5A DVFTU-5A3P- Note: Use with Lutron Tu-Wire line voltage control electronic dimming ballasts only. The nightlight is visible best on the lighter colors. For 3-way and 4-way switching, use with Claro switches or other mechanical switches.

1 For capacities in multigang installations see derating pg. 3.

2 Actual lamp wattages.

3 No derating required if ganged.

4 A physical barrier (partition) must exist when ganging with line-voltage products.

Controls

3 Have Questions? Call the Lutron Hotline 800-523-9466 To order—Call Lutron Customer Service 610-282-3800

Controls

Description Rating Model #

ACCESSORIES

Field Customizable Multi-Port Frame

6-Port Frame Shipped with 6 blanks CA-6PF- Shown with blanks

Product above: For use with Lutron connectors shown below. Also compatible with Hubble XceleratorTM and snap-fit connectors.

Connectors For use with 6-port frame (CA-6PF-). Each connector fills one port.

Phone Jack 6-conductor, RJ11, Category 3 CON-1P-C3-WH

Phone Jack 8-conductor, RJ45, Category 5e CON-1P-C5E-WH

Phone Jack 8-conductor, RJ45, Category 6 CON-1P-C6-WH

Fiber Jack MT-RJ Feed-Through CON-1F-MTRJ-WH

Fiber Jack SC Simplex CON-1F-SC-WH

Fiber Jack LC Non-Flush Mount CON-1F-LC-WH

Fiber Jack ST Style CON-1F-ST-WH

Cable Jack F-Style, 75-Ohm Coaxial cable CON-1C-WH

BNC Jack BNC connector CON-1B-WH

Connectors available in white (WH) only. For information about additional colors contact Lutron Customer Service.

DERATING/MAXIMUM CAPACITY

No side One side Two side sections section sections removed removed removed (Full Capacity) (End Units) (Middle Unit)

Incandescent Dimmers

600W 500W 400W 1000W 800W 650W

Electronic Low Voltage 1

300W 250W 200W

Magnetic Low Voltage

600VA 500VA 400VA

(450W 2) (375W 2) (300W 2)

1000VA 800VA 650VA

(800W 2) (650W 2) (500W 2)

Fluorescent

Hi-lume/Eco-10 20ballasts/8A No derating required (ECO-Series) Tu-Wire 3 5A 4A 3.3A

Fan-Speed Controls

1.5A No derating required

1 Requires 40W minimum load.

2 Actual lamp wattage.

3 Minimum capacity: 2 ballasts/0.25A

Description Model #

STANDARD WALLPLATES

1-Gang 2.94”W (75mm) x 4.69”H (119mm) x 0.30”D (7.6mm)

CW-1-

2-Gang 4.75”W (121mm) x 4.69”H (119mm) x 0.30”D (7.6mm)

CW-2-

3-Gang 6.56”W (167mm) x 4.69”H (119mm) x 0.30”D (7.6mm)

CW-3-

4-Gang 8.37”W (213mm) x 4.69”H (119mm) x 0.30”D (7.6mm) CW-4-

5-Gang 10.18”W (259mm) x 4.69”H (119mm) x 0.30”D (7.6mm) CW-5-

6-Gang 12.00”W (305mm) x 4.69”H (119mm) x 0.30”D (7.6mm) CW-6-

STANDARD COLORS/FINISHES

Gloss Finishes (Ships in 48 hours) Add color/finish suffix to model number to order.

Example: DV-600P-WH WH White IV Ivory AL Almond LA Light Almond GR Gray BR Brown BL Black

Have Questions? Call the Lutron Hotline 800-523-9466

Wiring Diagram 4 3-Way Wiring Model #

DVELV-303P-

CA-3PS-

Wiring Diagram 5 3-Way Used as Single Pole Model #

DVELV-303P-

WIRING DIAGRAMS

Wiring Diagram 1 Single-Pole Wiring Model #

DV-600P-

DV-10P-

DVLV-600P-

DVLV-10P-

CA-1PSH-

Wiring Diagram 2 Single-Pole Wiring of 3-Way Control Model #

DVFSQ-F-

DVLV-103P-

DVLV-603P-

DV-103P-

DV-603P-

Wiring Diagram 3 Single-Pole Wiring Model #

DVELV-300P-

Have Questions? Call the Lutron Hotline 800-523-9466 To order—Call Lutron Customer Service 610-282-3800

Neutral

Black *

Dimmer/ Switch/Fan-Speed Control

Black or Red *Hot

120VAC

60Hz

Lighting Load or FanGreen **

**or Brass screw terminal **or Green screw terminal

Ground

Wire Connectors

Control Load Side

Neutral

YellowHot

Green White

120VAC

60Hz

Red***

Lighting Load

3-Way Switch

3-Way Dimmer

Neutral

YellowHot

Green White

120VAC

60Hz

Red

Red Lighting Load

3-Way Dimmer

Ground

Wire Connectors

***or Copper/Black *** screw terminal ***or Brass/Gold *** screw terminal

***or Copper/Black *** screw terminal ***or Brass/Gold *** screw terminal

Ground

Wire Connectors

Green ***

Neutral

Black *

Red **†

Red **Hot

120VAC

60Hz

Lighting Load or Fan

Ground

Wire Connectors

***or Copper/Black screw terminal ***or Brass screw terminal ***or Green screw terminal † or Red/White stripe (cap off)

Dimmer/ Switch/Fan-Speed Control

Red or Yellow

Green White

Neutral

Black

Dimmer/Switch/ Fan-Speed Control

Hot

120VAC

60Hz

Lighting Load or Fan

Ground

Wire Connectors

WIRING DIAGRAMS

Wiring Diagram 6 3-Way Wiring Model #

DV-603P-

DV-103P-

DVLV-603P-

DVLV-103P-

DVFSQ-F-

CA-3PSH-

Wiring Diagram 7 4-Way Wiring Model #

DV-603P-

DV-103P-

DVLV-603P-

DVLV-103P-

DVFSQ-F-

CA-3PSH-

CA-4-PSH-

Have Questions? Call the Lutron Hotline 800-523-9466 To order—Call Lutron Customer Service 610-282-3800

Control Line Side 3-Way

Switch

Fan-Speed Control or 3-Way Dimmer/Switch

Fan-Speed Control or 3-Way Dimmer/Switch

Lighting Load or Fan

Neutral

Red *

Red *†

Green *** *** *** Green ***

Black **Hot

120VAC

60Hz

3-Way Switch

Lighting Load or Fan

Neutral

Red *

Red *†

Black **Hot

120VAC

60HzOR

Control Load Side

Ground

Wire Connectors

***or Brass/Gold *** screw terminal ***or Copper/Black *** screw terminal ***or Green screw *** terminal † or Red/White stripe

Control Line Side

Control Load Side

Black ** Red * *

Red *† *

Red *†*

Neutral

Hot

Green *** ***

120VAC

60Hz

3-Way Dimmer/Switch or Fan-Speed Control

4-Way Switch

Lighting Load or Fan

3-Way Switch

Neutral

Hot

Green ***

120VAC

60Hz

** Black **Red *

4-Way Switch

Lighting Load or Fan

3-Way Switch

3-Way Dimmer/Switch or Fan-Speed Control

OR

Ground

Wire Connectors

***or Copper/Black *** screw terminal ***or Brass/Gold *** screw terminal ***or Green *** screw terminal † or Red/White stripe

Wiring Diagram 8 Single-Pole Wiring of a 3-Way Control Model #

DVF-103P-

DVF-103P-277-

Wiring Diagram 9 3-Way Wiring Model #

DVF-103P-

DVF-103P-277-

CA-3PSH-

Have Questions? Call the Lutron Hotline 800-523-9466 To order—Call Lutron Customer Service 610-282-3800

Green

120VAC

or

277VAC

60Hz

To Additional Ballasts

Dimmer

Orange or Brown **

White *

BlackBlack

Orange or Brown **

White *

Yellow or Orange

Black

Blue RedHot

Neutral

White

Violet or Blue *** must use lamp ***disconnect sockets ***with magnetic ***dimming ballasts *** or Yellow/Blue or ***Yellow/Green when ***used with magnetic ***dimming ballasts

Dimming Ballast

Dimming Ballast

Ground

Wire Connectors

Typical 4-Wire Connection

Control Load Side

* 3-Way switch must be wired on line side of dimmer ** must use lamp disconnect sockets with magnetic dimming ballasts *** or Yellow/Blue or Yellow/Green when used with magnetic dimming ballasts † † or Copper/Black screw terminal † † or Brass/Gold screw terminal

GreenGreen

120VAC

or

277VAC

60Hz

To Additional Ballasts

Dimmer 3-Way Switch*

Orange or Brown ***

White **

Black

Orange or Brown ***

White **

Black

RedHot

Neutral

White

Violet or Blue

Yellow or Orange

Blue† † †

Dimming Ballast

Dimming Ballast

Ground

Wire Connectors

Typical 4-Wire Connection

Controls

Wiring Diagram 10 Single-Pole Wiring Model #

DVFTU-5A3P-

Wiring Diagram 11 3-Way Wiring Model #

DVTU-5A3P-

CA-3PSH-Black**Black

Green

To additional ballasts * or Red/White ** terminals are provided

Neutral

Red*

Red Dimmer

Black

White**

Hot

120VAC

60Hz

Tu-Wire™ Ballast

Ground

Wire Connectors

Black**Black

To additional ballasts * or Red/White ** terminals are provided

White** Green

Neutral

Red*

Red Dimmer

3-way Switch

BlackHot

Green

120VAC

60Hz

Ground

Wire Connectors

Tu-Wire™ Ballast

Wiring Diagram 12 Cable TV Jack Wiring Model #

CA-CJH-

Wiring Diagram 13 Telephone Jack Wiring Model #

CA-PJH-

Wiring Diagram 14 Receptacle Wiring Model #

CAR-15H-

Wiring Diagram 15 GFCI Receptacle Wiring Model #

CAR-15-GFCIH-

75-Ohm Cable 75-Ohm

Cable

Cable TV Jack

Ground

Neutral

Hot

Black

White

Green or Screw Terminal

Green or Screw Terminal

Green or Screw Terminal

Black

White

120VAC

60Hz

GFCI

Receptacle (15A Shown)

NPNP PP PP

Line Load

Wire ConnectorsP-Protected NP-Not Protected

Building Ground (To Metal Box)

Have Questions? Call the Lutron Hotline 800-523-9466 To order—Call Lutron Customer Service 610-282-3800

6-Conductor Telephone Jack*

Wire Color

Jack Position

1 White 2 Black 3 Red 4 Green 5 Yellow 6 Blue

* accepts most 4-conductor jacks

Neutral

Black

Receptacle (15A Shown)

WhiteHot

120VAC

60Hz

Nickel Plated Screws

Brass Screws

Green Screw Ground or

Isolated Ground

Ground

Wire Connectors

c. When on, the slider shall change the light level/fan speed.

When off, the slider shall preselect the light level/fan speed that the control will turn on to. Paddle switch shall turn lights/fan on to the preselected level, or off.

d. Paddle switch and slider shall be captured internal to the control.

e. 3-Way controls shall be capable of multi-location on and mechanical air-gap off using standard 3-way and 4-way switches. Multi-location switches shall be Claro decorator style with a gloss finish.

f. Dimmer shall be backlit with soft glow locator light.

g. Within rated capacity, dimmers shall be available for direct control of incandescent, magnetic low voltage, electronic low voltage, and fluorescent. Matching fan-speed controls shall also be available.

h. Controls shall be capable of operating at the rated capacity;

this includes modified capacities for ganging configurations which require the removal of fins. Operation at rated capacity shall be possible across the full ambient temperature range, without shortening design lifetime.

i. To ensure a precise color match between all plastic parts, color variation of any gloss finish control shall not exceed a delta E of 1, CIE L*a*b* color units, as defined in ASTM E 308-99.

j. Dimmer shall provide smooth and continuous Square Law dimming curve, for the full slider travel, on their rated load per The IESNA Lighting Handbook, 9th edition, p. 27-4.

k. Controls shall meet the applicable requirements of UL 20 and UL 1472 referring to the inclusion of a visible, accessible air-gap off switch and the limited short circuit test.

l. Controls shall meet ANSI/IEEE Std. C62.41-1980, tested to withstand voltage surges of up to 6000V and current surges of up to 200A without damage.

m. Dimmers shall be designed to reduce interference with radio, audio, and video equipment.

n. Controls shall incorporate power-failure memory. Should power be interrupted and subsequently returned, the lights or fans will come back on to the same levels set prior to the power interruption. Restoration to some other default level is not acceptable.

o. Controls shall not be susceptible to damage or loss of memory due to static discharge.

p. Controls shall operate in an ambient temperature range of 0°C (32°F) to 40°C (104°F).

q. 3-Way controls shall wire using conventional 3-way and 4-way wire runs.

r. Contractors shall install all backboxes with a minimum wallbox depth of 2.5 inches.

2. Incandescent Dimmers

a. Provide single-pole and 3-way incandescent dimmers in 600

Watts and 1000 Watts capacities.

b. Dimmer shall be capable of operating in either 3-way switch location.

c. Dimmer shall be capable of operating in either 3-way switch location.

3. Electronic (Solid State) Low Voltage (ELV) Transformer Dimmers

a. Provide ELV dimmers for direct control of up to 300 watts of electronic low voltage load.

b. Dimmers shall contain circuitry specifically designed to control the input of electronic (solid state) low voltage transformers. Dimmers using standard phase control shall not be acceptable.

DIVA CONTROLS AND ACCESSORIES

PART 1 – GENERAL

1.01 SUMMARY

A. Scope: Provide, install and test all switches, dimmers and related devices as specified herein for the areas indicated on the drawings, specifications, and load schedules.

B. Related Sections: Section 16580 (Ballasts), Section 16570 (Dimming Systems).

1.02 REFERENCES

A. UL 20, UL 1472, CSA, NOM, ISO 9001

1.03 SYSTEM DESCRIPTION AND OPERATION

A. Permanently installed, wallbox mounted switches and dimmers B. Permanently installed, wallbox mounted fan-speed controls C. Permanently installed, wallbox mounted receptacles D. Permanently installed, wallbox mounted data, voice and cable jacks E. Screwless, seamless wallplates

1.04 SUBMITTALS

A. Submit manufacturer's standard catalog data giving all application, wiring, and installation information on basic components and wallplate kits. Provide test data and/or samples as required to demonstrate conformance with PART 2 of this specification.

1.05 QUALITY ASSURANCE

A. Manufacturer shall have a minimum of 10 years continuous experience in manufacturing wallbox dimming products.

B. Dimmers, switches and Fan-speed controls shall be UL listed, CSA and NOM approved specifically for each required load (i.e., tungsten, electronic low voltage transformer, magnetic low voltage transformer, and fluorescent). Manufacturer shall provide file card or certificate upon request. Universal load-type dimmers shall not be acceptable.

C. Manufacturer shall maintain ISO 9001 certification and provide a copy of the certificate upon request.

1.06 WARRANTY

A. All devices shall be covered by a minimum one-year warranty.

PART 2 – EQUIPMENT

2.01 ACCEPTABLE MANUFACTURERS

A. Lutron Electronics Co., Inc.

B. Unless otherwise noted, all basic components (dimmer, fan-speed control, switch, receptacle, telephone jack and cable TV jack) and wallplate kits shall be provided by one manufacturer.

2.02 EQUIPMENT

A. Controls Lutron Diva Style

1. Performance

a. Dimmers shall provide full-range, continuously variable control of light intensity.

b. Wall controls shall fit a decorator wallplate opening with a paddle switch. Dimmers shall have a small, raised slider to the right of the paddle switch. Controls shall have a gloss finish.

Have Questions? Call the Lutron Hotline 800-523-9466

b. Receptacles shall be two pole, three wire ground and rated for 15A at 125VAC. All receptacles shall be NEMA configuration type 5-15R.

c. Ground-fault interrupter receptacles shall be Lutron Claro style with two-pole, three-wire ground and rated 15A at 125VAC Configuration shall be of the duplex type with rectangular NEMA WD-6 design. Receptacles shall have a 5 milliampere ground-fault trip level with "test" and "reset" buttons.

3. Telephone Jack and Cable TV Jack Components Lutron Claro Style

a. Contractor shall provide an appropriate barrier (partition) to isolate jack from high-voltage wiring when ganged with a dimmer, fan-speed control, switch, or receptacle. This complies with NEC Articles 800-3 and 820-13.

b. Telephone jack shall be designed to mate with standard 4- or 6-conductor modular jacks, and be compatible with 2, 4, or 6 conductor lines. Telephone jacks shall meet FCC Part 68, paragraph F standards to ensure compatibility with U.S. telephone systems.

c. Cable TV jacks shall be the coaxial type, designed for use with standard 75-Ohm cables.

C. Wallplates Lutron Claro Style

1. Wallplates shall be manufactured from durable polycarbonate plastic with gloss finish, and shall attach to the basic components without using exposed hardware or screws.

2. Multigang wallplates shall provide a continuous, seamless cover for up to six-ganged decorator-style control and accessory combinations with no exposed hardware or screws.

3. Multigang wallplates shall include an adapter plate for proper device alignment and wallplate attachment.

4. Control, accessory and wallplate profiles shall not exceed .30 inches from wall surface to faceplate front surface.

5. To ensure a precise color match between all plastic parts, color variation of any gloss finish control or wallplate shall not exceed a delta E of 1, CIE L*a*b* color units, as defined in

ASTM E 308-99.

6. Visible parts of dimmers, switches, standard receptacles, cable jacks or any wallplate shall exhibit ultraviolet stability when tested with multiple actinic light sources as defined in ASTM D4674-89.

2.03 SOURCE QUALITY CONTROL

A. All dimming controls shall be 100% function tested at the time of manufacture. Statistical sampling plan shall not be acceptable.

c. Dimmers shall have a resettable overload protection that automatically shuts off when dimmer capacity is exceeded.

Protection methods that are non-resettable or require the device to be removed from the wall to reset shall not be acceptable.

d. Dimmers shall be designed to withstand a short, per UL 1472 section 5.10, between load hot and either neutral or ground without damage to the dimmer.

4. Magnetic Low Voltage (MLV) Transformer Dimmers

a. Provide MLV dimmers for direct control of up to 1000 volt amps of electronic low voltage load.

b. Dimmers shall contain circuitry specifically designed to control and provide a symmetrical AC waveform to the input of magnetic low voltage transformers per UL1472 section 5.11.

c. Dimmers shall not cause a magnetic low voltage transformer to operate above the transformers rated operating current or temperature.

d. Dimmer shall be capable of operating in either 3-way switch location.

5. Fluorescent Dimming Ballast Dimmers

a. Provide Fluorescent dimmers for direct control of fluorescent dimming ballasts up to the manufacturers specified rating.

b. Dimmers shall be designed to operate the following ballasts.

Dimmers and ballasts shall be produced by the same manufacturer to ensure proper ballast/control compatibility:

1) Hi-lume® Architectural Dimming Ballasts (1% 3-wire)

2) Hi-lume® CompactTM Lamp Dimming Ballasts

(5% 3-wire)

3) Eco-10TM Lighting Management Dimming Ballasts

(10% 3-wire)

4) Tu-Wire™ High Performance Dimming Ballasts

(5% 2-wire)

6. Remote dimming modules for high power loads

a. Where lighting loads exceed the full rated capacity of single dimmers, provide a Diva incandescent dimmer driving high power modules. High power module and dimmer shall be from the same manufacturer to ensure compatibility.

b. High power modules shall be remotely mounted.

c. High power module shall be rated and UL listed for control of incandescent, magnetic low voltage, electronic low voltage, fluorescent, and neon/cold cathode loads in increments of 2,000 Watts up to 30,000 Watts.

7. Fan-Speed Controls:

a. Fan-speed controls shall be UL Listed, CSA and NOM approved, Lutron Diva style.

b. Quiet fan-speed model shall provide three speed settings with paddle providing preset on and off.

c. Quiet fan-speed control shall provide single-pole/3-way control of one paddle fan (1.5A max.).

B. Accessories Lutron Claro Style

1. Switch Components Lutron Claro Style

a. Switches shall provide on/off control of any 120/277 VAC load up to 15A. Switches shall be UL Listed as general-use AC switches, Lutron Claro style.

b. Switches shall be available in single-pole, 3-way and 4-way configurations.

2. Receptacle Components Lutron Claro Style

a. All receptacles shall be UL Listed, CSA and NOM approved.

Controls

Have Questions? Call the Lutron Hotline 800-523-9466

PART 3 – EXECUTION

3.01 INSTALLATION

A. Contractor shall furnish all devices (dimmers, accessories, & wallplate kits), labor and other services necessary for the proper installation of the devices as indicated on the drawings and specified herein.

B. Contractor shall be responsible for derating dimmer capacity if side sections are removed.

C. Contractor shall run separate neutral wires in 120/208 VAC installations.

D. Devices shall be installed utilizing manufacturer's recommended application, wiring and installation instructions.

E. Contractor to provide seamless wallplate covers per specification

2.02 for all devices ganged in a common box. Contractor shall provide barriers within the box where required by code.

3.02 FIELD QUALITY CONTROL

A. Twenty-four hours a day, seven days a week, global customer service and technical hotline available.

B. Supplemental information shall be provided by manufacturer's Internet site.

Controls

Lutron Electronics Co., Inc.

7200 Suter Road • Coopersburg, PA 18036 U.S.A.

Made and printed in U.S.A. 03/2003 ©2003