L. CHIP Programming job aid 1.pdf
PDF 286 KB Posted
- Attached to
- 3650--763-26-2-228-0242 -Lancaster CMOP Low to Medium Volume TCA and Sorting Loops Project (VA-26-00039446)
- Solicitation number
- 36C77026T0007
About this file
This document is a job aid for the CHIP Program that provides step-by-step guidance on programming chips using RFID technology. The document is marked as Confidential, Version 001, and was revised on September 14, 2021.
The job aid instructs users to log into WSCRAWLS or any workstation with the DASHBOARD Program and connect a programmed reader to initiate the chip programming process. Users must configure the BALLUFF DASHBOARD software with a 19200 baud rate and select device type BISM-410, then connect to the system and place the chip on the reader write box. The tag type must be set to NXP ICODE1 with specific parameters: baud rate at 19200, continuous read length at 8 bytes, and delay at 1. After selecting the Read/write tab, users must set both the continuous read length and read/write length to 8 bytes. Once tag data is entered, the user clicks "Write Tag Data" to program the chip. The final verification step requires removing the chip and placing it back on the reader to confirm the ID was properly added; the identification number should appear in the tag data scrolling text field. This internal procedural document is uncontrolled when printed and directs users to refer to the posted version on SharePoint for the most current information.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| 1 day snapshot.xlsx | XLSX spreadsheet | |
| G. Dallas Manual Dispensing for New TCA.xlsx | XLSX spreadsheet | |
| H. Dallas TCA Products 07132026.xlsx | XLSX spreadsheet | |
| K. L034.00113-510A.pdf | ||
| I. Dallas_CMOP_Floor Plan.pdf | ||
| B. Attachment 1 for Dallas CMOP TCA Low to Medium Volume.docx | DOCX document | |
| A. PWS TCA System Installation_Final_updated 7.8.26.docx | DOCX document | |
| J. FlexLink Layout from KNAPP System.docx | DOCX document | |
| E. BOT2000.pdf | ||
| RFP_36C77026R0007_extended.docx | DOCX document | |
| D. Past Performance Questionnaire.docx | DOCX document | |
| F. CAP1185CL-foil-lined- CAP1190CL-foam-lined.pdf | ||
| C. BUSINESS ASSOCIATE AGREEMENT.pdf | ||
| M. CHIP Program Deleting job aid 2.pdf | ||
| S06_Amendment_36C77026R0007.docx | DOCX document | |
| S05_Questions and Clarifications_R0007.docx | DOCX document |
Show all 16
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
CHIP PROGRAM Job Aid 1
Version
New ___ Revised __X Revision Date: 9/14/2021 Original Issue Date: X/X/2020
CONFIDENTIAL 1 of 4 This document is uncontrolled when printed. Refer to posted document version on SharePoint.
PURPOSE: To provide guidance on how to Program CHIPS
LOG INTO: WSCRAWLS or any workstation that has the DASHBOARD Program
1. Connect Reader
Note: Must use a programed reader.
2. Pull up BALLUFF DASHBOARD and Select 19200 Baud rate
3. Select Device Type: BISM-410
CONFIDENTIAL 2 of 4
4. Select: connect
5. Place chip on READER WRITE BOX
6. Make Tag Type NXP ICODE1
Note: make sure baud rate is at 19200, continuous Read is set at 8 for the Length, and Delay is at 1
CONFIDENTIAL 3 of 4
7. Select Read/write Tab
8. In the Continuous Read box: Set the length to 8 bytes and Read/Write Length also to
CONFIDENTIAL 4 of 4
9. Enter Tag Data and Click on WRITE TAG DATA
10. REMOVE CHIP and verify ID was properly Added by placing back on reader.
Number should Appear in tag Data Scrolling Text Field.
File details come from the government source that posted it. Updated .