JUNIPER DD FY26 REV0 SPEC 16Mar2026.pdf

USCGC JUNIPER (WLB 201)

SPECIFICATION FOR DRYDOCK REPAIRS

FY2026

Developed By: K A H

(Rev-0, 16 Mar 2026)

USCGC JUNIPER (WLB-225A) DRYDOCK AVAILABILITY FY2026

ii (Rev-0)

TABLE OF CONTENTS

Revisions Record ........................................................................................................................................... v Consolidated List of References ................................................................................................................... vi Consolidated List of Government-furnished Property ............................................................................. xvii Consolidated List of Critical Inspection Items ......................................................................................... xxii Principal Characteristics ........................................................................................................................... xxiv General Requirements WORK ITEM 1: Fire Prevention Requirements WORK ITEM 2: Hull Plating, U/W Body, Inspect WORK ITEM 3: Hull Plating, U/W Body, Ultrasonic Testing WORK ITEM 4: Hull Plating, Freeboard, Ultrasonic Testing WORK ITEM 5: U/W Body, Preserve, 100 percent WORK ITEM 6: U/W Body, Preserve, Partial, Condition A WORK ITEM 7: U/W Body, Preserve, Partial, Condition B WORK ITEM 8: U/W Body, Preserve, Partial, Condition C WORK ITEM 9: Hull Plating Freeboard, Preserve, Partial WORK ITEM 10: Hull Plating Freeboard, Preserve, 100 Percent WORK ITEM 11: Appendages, U/W, Leak Test WORK ITEM 12: Propulsion Shaft Fairwaters And Rope Guards, Inspect WORK ITEM 13: Appendages, U/W, Internal, Preserve WORK ITEM 14: Chain Lockers, Clean and Inspect WORK ITEM 15: Voids, Non-Accessible, Leak Test WORK ITEM 16: Voids, Non-Accessible, Internal Surfaces, Preserve WORK ITEM 17: Tanks, Potable Water, Clean and Inspect WORK ITEM 18: Tanks, Ballast, Clean and Inspect WORK ITEM 19: Tanks, Dirty Oil and Waste, Clean and Inspect WORK ITEM 20: Main Reduction Gear, Overhaul WORK ITEM 21: Propulsion Shafting; Remove, Inspect, and Reinstall WORK ITEM 22: Propulsion Shaft Seals, Mechanical Overhaul And Inflatable Renewal WORK ITEM 23: Propulsion Shaft Seals, Bulkhead, Overhaul WORK ITEM 24: Strain Gage Alignment, Check WORK ITEM 25: Propulsion Tail Shaft Sleeve, Skim Cut WORK ITEM 26: Propulsion Shaft Bearings, External, Check Clearances WORK ITEM 27: Propulsion Shaft Bearing, Stave Renewal WORK ITEM 28: Stern Tube Interior Surfaces, Preserve, 100 Percent WORK ITEM 29: Controllable Pitch Propellers, Clean and Inspect WORK ITEM 30: Controllable Pitch Propeller, System Maintenance, Perform WORK ITEM 31: Controllable Pitch Propeller Hub, General Maintenance with EAL, Perform WORK ITEM 32: Controllable Pitch Propeller Hub, Remove and Reinstall WORK ITEM 33: Heat Exchangers, Clean, Inspect And Hydro WORK ITEM 34: Ship Service Diesel Generator, Clean and Inspect WORK ITEM 35: Emergency Diesel Generator, Clean & Inspect WORK ITEM 36: Fathometer Transducer, General Maintenance WORK ITEM 37: Sea Valves and Waster Pieces, Overhaul Or Renew WORK ITEM 38: Sea Strainers, Duplex, All Sizes, Overhaul WORK ITEM 39: Sea Strainers, Simplex, All Sizes, Clean and Inspect WORK ITEM 40: Sea Bay, Clean and Inspect WORK ITEM 41: Sea Bay, Preserve 100% WORK ITEM 42: Rudders, Preserve, 100 Percent iii (Rev-0)

WORK ITEM 43: Rudder Stock Bearings, Check Clearances WORK ITEM 44: Rudder, Inspect And Repair WORK ITEM 45: Rudder and Rudder Stock, Remove and Inspect WORK ITEM 46: Rudder Bearings, Renewal WORK ITEM 47: Thruster Units, Overhaul Fluid EAL WORK ITEM 48: Thruster Generator, Clean & Inspect WORK ITEM 49: Anchor Windlass, Inspect and Service WORK ITEM 50: Anchor Chains and Ground Tackle, Inspect and Repair WORK ITEM 51: Anchor Chain and Ground Tackle, Preserve WORK ITEM 52: Anchors, Preserve WORK ITEM 53: Hawse Pipes, Preserve WORK ITEM 54: Hull Fittings (Mooring and Towing), Inspect and Test WORK ITEM 55: Accessible Voids, Preserve, 100 Percent WORK ITEM 56: Tanks, Ballast, Preserve, 100 Percent WORK ITEM 57: Tanks, Ballast, Preserve, Partial WORK ITEM 58: Chain Locker, Preserve, 100 Percent WORK ITEM 59: Chain Lockers, Preserve, Partial WORK ITEM 60: Accessible Void(s), Preserve, Partial, WORK ITEM 61: Tanks, Potable Water Preserve, 100 Percent WORK ITEM 62: Tanks, Potable Water, Preserve, Partial, WORK ITEM 63: Decks – Exterior (Buoy or Construction Deck), Preserve 100% WORK ITEM 64: Hull Plating Freeboard (Buoy Port Areas), Preserve WORK ITEM 65: Superstructure, Preserve, Partial WORK ITEM 66: Cathodic Protection, Zinc Anodes, Renew, WORK ITEM 67: Impressed Current Cathodic Protection System, Inspect and Maintain WORK ITEM 68: Impressed Current, Cathodic Protection System, Reference Cells, Renew WORK ITEM 69: Drydock WORK ITEM 70: Temporary Services, Provide - Cutter WORK ITEM 71: Sea Trial Performance, Support, Provide WORK ITEM 72: ATON Tie Down Installation WORK ITEM 73: Compartment Insulation, General, Renew WORK ITEM 74: Firemain Valves, Overhaul or Renew WORK ITEM 75: Space or Component, Preserve WORK ITEM 76: Welin Lambie Dual Point Davit TWPIV 5.0B, Renew WORK ITEM 77: ATON Tie-down Install WORK ITEM 78: Anchor Tripping Bracket Install WORK ITEM 79: Fluxgate Digital Compass System, Upgrade WORK ITEM 80: Pilothouse Exterior Safety Rail, Renew WORK ITEM 81: Forecastle Raised Hatch, Renew WORK ITEM 82: Buoy Deck Quick Acting Watertight Door, Renew WORK ITEM 83: Air Escape (AE) Piping, Renew WORK ITEM 84: Weathertight Doors, Renew WORK ITEM 85: Directional Control Valve, Upgrade WORK ITEM 86: Pilot House Windows and Frame, Repair and Reseal WORK ITEM 87: Tanks, MP Fuel Stowage and Overflow, Clean and Inspect WORK ITEM 88: Decks - Exterior, Preserve, Non-Skid Broadcast Grit System WORK ITEM 89: Potable Water Pump Room Deck, Preserve WORK ITEM 90: Steering Gear Heat Exchanger, Modify WORK ITEM 91: Steering System PLC, Upgrade WORK ITEM 92: Buoy Deck Incline Ladders, Renew WORK ITEM 93: Tenting, Provide iv (Rev-0)

WORK ITEM 94: Independent NACE Inspector (Level 3), Provide v (Rev-0)

REVISIONS RECORD

This page is used to record specification revisions, which may have occurred subsequent to a Revision 0 (Rev-0) package. Information listed is intended to provide contractors and field unit personnel a means to ensure all the current specification revision pages are present when reviewing or utilizing this specification package.

DATE REV# WORK

ITEM#

CHANGES MADE

NOTE : All work item and paragraph numbers listed above for a given revision correspond to same numbers in the previous revision. This revised specification is self-contained with all of the above listed changes incorporated.

vi (Rev-0)

CONSOLIDATED LIST OF REFERENCES

The below-listed documents form a part of this specification to the extent specified herein. Approval/publication dates or revision dates/numbers are also identified, to ensure that same document versions are used at the time of specification writing and during contract execution.

All Coast guard drawings, technical publications, and standard specifications will be provided to contractors by the Coast Guard at an appropriate time, or upon request, free of charge. Other Government documents may be accessed – free of charge – from links located on the SFLC website. Commercial sites provide access to their respective documents.

COAST GUARD DRAWINGS

«Drawings»

Coast Guard Drawing (CGDWG) 225-WLB-561-202, Rev B, JAN 2021, Steering Control Wiring Diagram

Coast Guard Drawing 225 910-001, Rev E, Hull Block 910, Panels

Coast Guard Drawing 225 WLB 114-001, Rev D, Shell Appendages

Coast Guard Drawing 225 WLB 114-001, Rev D; Shell Appendages

Coast Guard Drawing 225 WLB 114-002, Rev A, Flow Accelerating Fin

Coast Guard Drawing 225 WLB 801-006, Rev C; Docking Drawing

Coast Guard Drawing 225 WLB 801-006, Rev D, Docking Drawing

Coast Guard Drawing 225 WLB 801-006, Rev E, Docking Drawing

Coast Guard Drawing 225 WLB 111-001, Rev D, Shell Expansion

Coast Guard Drawing 225 WLB 111-001, Rev D; Shell Expansion

Coast Guard Drawing 225 WLB 180-002, Rev G, Foundations, Block 910

Coast Guard Drawing 225 WLB 184-001, Rev B, CRP-V850 Transducer Adapter Ring

Coast Guard Drawing 225 WLB 201-001, Rev G, Machinery Spaces Arrangement

Coast Guard Drawing 225 WLB 243-001, Rev C, Propulsion Shafting Arrangement

Coast Guard Drawing 225 WLB 243-002, Rev F, Stern Tube and Bearings A&D

Coast Guard Drawing 225 WLB 243-202, Rev C, Bulkhead Type Seal

Coast Guard Drawing 225 WLB 243-206, Rev E, CPP Propeller Shaft

Coast Guard Drawing 225 WLB 243-207, Rev D, CPP Shaft Installation

Coast Guard Drawing 225 WLB 256-001, Rev P, Seawater Cooling System Diagram

Coast Guard Drawing 225 WLB 256-001, Rev U, Seawater Cooling System Diagram

Coast Guard Drawing 225 WLB 320-001, Rev AK, Electrical One-Line Diagram

Coast Guard Drawing 225 WLB 437-005, Rev H, Gyrocompass & Magnetic Compass Sys Block, WDP

& EWD

Coast Guard Drawing 225 WLB 506-001, Rev N, Overflows, Air Escapes and Sounding Tubes Diagram

Coast Guard Drawing 225 WLB 506-005, Rev D, Vents & ST System A/D, FR 48-66 Block 930

Coast Guard Drawing 225 WLB 506-007, Rev E, Ovfl, AE & ST Sys, A/D MN DK & Above, Block 960A, 970 vii (Rev-0)

Coast Guard Drawing 225 WLB 506-010, Rev A, MMA Overflows, Air Escapes & Sounding Tubes Diagram

Coast Guard Drawing 225 WLB 541-001, Rev J, Fuel Oil System Diagram

Coast Guard Drawing 225 WLB 541-001, Rev K, Fuel Oil System Diagram

Coast Guard Drawing 225 WLB 541-007, Rev D; Incinerator Fuel Oil Service Tank

Coast Guard Drawing 225 WLB 541-020, Rev -, Mods To Fuel Oil Cooling System and Associated Piping

Coast Guard Drawing 225 WLB 556-001, Rev K, Hydraulic System Diagram

Coast Guard Drawing 225 WLB 556-003, Rev C, Forward Hydraulic System A&D

Coast Guard Drawing 225 WLB 562-002, Rev F; Rudder Structural A & D

Coast Guard Drawing 225 WLB 562-002, Rev G, Rudder Structural A&D

Coast Guard Drawing 225 WLB 562-003, Rev B, Rudder Assembly for Logistics and Support

Coast Guard Drawing 225 WLB 581-001 Rev E, Anchor Handling System Arrangement

Coast Guard Drawing 225 WLB 581-001, Rev E, Anchor Handling System Arrangement

Coast Guard Drawing 225 WLB 582-001, Rev E, Mooring and Towing A & D

Coast Guard Drawing 225 WLB 601-001, Rev AA, GENERAL ARRANGEMENTS INBOARD AND

OUTBOARD PROFILES

Coast Guard Drawing 225 WLB 601-001, Rev AC; General Arrangement Inboard & Outboard Profiles

Coast Guard Drawing 225 WLB 601-001, Rev M, General Arrangement Inboard & Outboard Profiles

Coast Guard Drawing 225 WLB 601-001, Rev M; General Arrangement Inboard & Outboard Profiles

Coast Guard Drawing 225 WLB 601-001, Rev T; General Arrangement Inboard and Outboard Profiles

Coast Guard Drawing 225 WLB 601-002 Rev R, Booklet of General Drawings

Coast Guard Drawing 225 WLB 601-002, Rev G, Booklet of General Drawings

Coast Guard Drawing 225 WLB 601-002, Rev K, Booklet of General Drawings

Coast Guard Drawing 225 WLB 601-002, Rev R, Booklet of General Drawings

Coast Guard Drawing 225 WLB 633-001, Rev F, Cathodic Protection System Arrangement, Block Diagram, Wiring Deck Plan, and Elementary Diagrams

Coast Guard Drawing 225 WLB 633-002, Rev B, Cathodic Protection Passive

Coast Guard Drawing 225 WLB 633-002, Rev B; Cathodic protection-passive

Coast Guard Drawing 225 WLB 635-001, Rev J, Hull, Thermal, & Acoustic Insulation Schedule

Coast Guard Drawing 225 WLB 801-001, Rev C, Lines and Offsets

Coast Guard Drawing 225 WLB 801-003, Rev A, Curves of Form and Cross Curves of Stability

Coast Guard Drawing 225 WLB 801-005, Rev D, Tank CAPACITY - 95% Curves

Coast Guard Drawing 225 WLB 801-006, Rev C; Docking Drawing

Coast Guard Drawing 225 WLB 801-006, Rev F, Docking Drawing

Coast Guard Drawing 225 WLB 801-020, Rev A, Tank CAPACITY - 95% Curves (203, 204, 205)

Coast Guard Drawing 225 WLB 901-003, Rev C, Hull Block 901 Block Assembly

Coast Guard Drawing 225 WLB 940-001, Rev F; Hull Block 940 - Modules

Coast Guard Drawing 225 WLB 940-001, Rev G; Hull Block 940 – Panels

Coast Guard Drawing 225 WLBB 601-002, Rev G Booklet of General Drawings

Coast Guard Drawing 225B WLB 243-001, Rev J, Propulsion Shaft Arrangement

Coast Guard Drawing 225B WLB 243-002, Rev G, Stern Tube and Bearings A&D viii (Rev-0)

Coast Guard Drawing 225B WLB 256-001, Rev M, Seawater Cooling System Diagram

Coast Guard Drawing 225B WLB 320-001, Rev AD, Electrical One-Line Wiring Diagram

Coast Guard Drawing 225B WLB 437-005, Rev F, Gyrocompass & Magnetic Compass Sys Block, WDP

& EWD

Coast Guard Drawing 225B WLB 568-1, Rev A, Bow Thruster Arrangement and Detail

Coast Guard Drawing 225B WLB 601-001, Rev AB; General Arrangement Inboard and Outboard Profiles

Coast Guard Drawing 225B-WLB 243-1, Rev J, Propulsion Shafting Arrangement

Coast Guard Drawing 225B-WLB 243-2, Rev G, Stern Tube and Bearing A & D

Coast Guard Drawing 225B-WLB 111-01, Rev A, Shell Expansion

Coast Guard Drawing 225B-WLB 243-001, Rev J, Propulsion Shafting Arrangement

Coast Guard Drawing 225B-WLB 243-002, Rev G, Stern Tube and Bearing a & D

Coast Guard Drawing 225B-WLB 243-1, Rev J, Propulsion Shafting Arrangement

Coast Guard Drawing 225B-WLB 243-2, Rev G, Stern Tube and Bearing A & D

Coast Guard Drawing 225B-WLB 243-2, Rev G; Stern Tube and Bearing A & D

Coast Guard Drawing 225B-WLB 256-001, Rev P; Seawater Cooling Sys Diagram

Coast Guard Drawing 225B-WLB 505-1, Rev D; General Requirements for Piping Systems

Coast Guard Drawing 225B-WLB 561-001, Rev C, Steering Gear Hydraulic Diagram

Coast Guard Drawing 225B-WLB 561-005, Rev E; Steering Gear Heat Exchanger Replacement

Coast Guard Drawing 225B-WLB 568-2, Rev A, Stern Thruster Arrangement and Detail

Coast Guard Drawing 225B-WLB 581-01, Rev G, Anchor Handling System Arrgt

Coast Guard Drawing 225B-WLB 601-01, Rev N, General Arr, Inboard and Outboard Profiles

Coast Guard Drawing 225B-WLB 901-02, Rev D, Hull Block 901 Modules

Coast Guard Drawing 225B-WLB-438-002, Rev C, Buoy Deck Controls Install to Suit MMA Aton Crane

Coast Guard Drawing 225-WLB 243-2, Rev F; Stern Tube and Bearings A & D

Coast Guard Drawing 225-WLB 556- 8, Rev F, CPP Hydraulic System Diagram

Coast Guard Drawing 225-WLB 561-003, Rev F; Steering Gear Arrangement

Coast Guard Drawing 225-WLB 562-001, Rev L; Steering Components Arrangement and Detail

Coast Guard Drawing 225-WLB 562-002, Rev G, Rudder Structural A & D

Coast Guard Drawing 225-WLB 562-002, Rev G; Rudder Structural A&D

Coast Guard Drawing 225-WLB 562-003, Rev B; Rudder Assembly for Logistics & Support

Coast Guard Drawing 225-WLB 562-004, Rev A; Thordon Rudder Stock Bearing Assembly and Detail

Coast Guard Drawing 225-WLB 562-5, Rev -; Pintle Bearing

Coast Guard Drawing 225-WLB 611-1, Rev G, Lifting Pads - Main and Aux Machinery Room

Coast Guard Drawing 225-WLB 111-001, Rev D, Shell Expansion

Coast Guard Drawing 225-WLB 111-01, Rev D, Shell Expansion

Coast Guard Drawing 225-WLB 167-1, Rev W, Structural Closures

Coast Guard Drawing 225-WLB 201-2, Rev B, Access Removal Routes

Coast Guard Drawing 225-WLB 233-001, Rev H; Propulsion Train Installation Drawing

Coast Guard Drawing 225-WLB 233-001, Rev H; PROPULSION TRAIN INSTALLATION DRAWING

Coast Guard Drawing 225-WLB 243-001, Rev B; PROPULSION SHAFTING ARRANGEMENT

Coast Guard Drawing 225-WLB 244-203, Rev E, Stern Tube Split Dovetail Carrier Casting ix (Rev-0)

Coast Guard Drawing 225-WLB 256-001, Rev U; Seawater Cooling Sys Diagram

Coast Guard Drawing 225-WLB 505-1, Rev D; General Requirements for Piping Systems

Coast Guard Drawing 225-WLB 561-001, Rev E Steering Gear Hydraulic Diagram

Coast Guard Drawing 225-WLB 561-003, Rev F; STEERING GEAR ARRANGEMENT

Coast Guard Drawing 225-WLB 561-005, Rev H; Steering Gear Heat Exchanger Replacement

Coast Guard Drawing 225-WLB 562-001, Rev L; STEERING COMPONENTS ARRANGEMENT AND

DETAIL

Coast Guard Drawing 225-WLB 562-001, Rev M; Steering Components Arrangement and Detail

Coast Guard Drawing 225-WLB 562-002, Rev G; RUDDER - STRUCT A & D

Coast Guard Drawing 225-WLB 562-002, Rev G; RUDDER STRUCTURAL A & D

Coast Guard Drawing 225-WLB 562-002, Rev G; Rudder Structural A&D

Coast Guard Drawing 225-WLB 562-004, Rev A; Thordon Rudder Stock Bearing Assembly and Detail

Coast Guard Drawing 225-WLB 562-005, Rev -; Pintle Bearing

Coast Guard Drawing 225-WLB 562-005, Rev -; PINTLE BEARING

Coast Guard Drawing 225-WLB 573-01, Rev R, Buoy Handling System Arrangement

Coast Guard Drawing 225-WLB 573-012, Rev D, Replacement Aton Tie Downs

Coast Guard Drawing 225-WLB 573-11, Rev F, ATON Tie Downs

Coast Guard Drawing 225-WLB 573-12, Rev F, Replacement Tie-downs

Coast Guard Drawing 225-WLB 581-01, Rev F, Anchor Handling System Arrgt

Coast Guard Drawing 225-WLB 583-002, Rev E, MMA Installation of Dual Point Davit

Coast Guard Drawing 225-WLB 583-004, Rev A, MMA Installation of Dual Point Davit

Coast Guard Drawing 225-WLB 601-001, Rev AC, General Arrangements Inboard and Outboard Profiles

Coast Guard Drawing 225-WLB 601-002, Rev T, Booklet off General Drawings

Coast Guard Drawing 225-WLB 601-01, Rev T, General Arr, Inboard and Outboard Profiles

Coast Guard Drawing 225-WLB 601-1, Rev AC, General Arr, Inboard & Outboard Profile

Coast Guard Drawing 225-WLB 631-2, Rev K, Painting Schedule

Coast Guard Drawing 225-WLB 801-013, Rev D, Midship Section & Typical Sections

Coast Guard Drawing 225-WLB 801-015, Rev D, Scantling, Decks, & Platforms

Coast Guard Drawing 225-WLB 801-016, Rev C, Scantlings, Watertight Bulkheads

Coast Guard Drawing 225-WLB 901-02, Rev C, Hull Block 901 Modules

Coast Guard Drawing 225-WLB 930-001, Rev H, Hull Block 930 Panels

Coast Guard Drawing 225-WLB 940-002, Rev F, Hull Block 940 - Modules

Coast Guard Drawing 225-WLB-167-001, Rev W, Structural Closures

Coast Guard Drawing 225-WLB-320-001 Rev AT, Electrical One-Line Diagram

Coast Guard Drawing 225-WLB-320-007 Rev W, Power Sys Deck Plan 02 Level & Above, Hull Block 960B, 975, & 970

Coast Guard Drawing 225-WLB-437-210, Rev D, Buoy Deck Equipment Electrical Control System Mods Blk & Elem Wiring Diagram

Coast Guard Drawing 225-WLB-438-002, Rev D, Buoy Deck Controls Install to Suit MMA Aton Crane

Coast Guard Drawing 225-WLB-521-001-F., Firemain System Diagram

Coast Guard Drawing 225-WLB-521-001-K., Firemain System Diagram

Coast Guard Drawing 225-WLB-521-003, Firemain CLA-VAL Installation x (Rev-0)

Coast Guard Drawing 225-WLB-573-207, Rev -, Replacement DCV Amplifier Card Wiring Diagram

Coast Guard Drawing 225-WLB-601-001, Rev AC, General Arr, Inboard & Outboard Profile

Coast Guard Drawing 225-WLB-612-001, Rev L, Lifelines, Liferails & Stanchions

Coast Guard Drawing 225-WLB-623-002, Rev F, Ladders - Inclined

Coast Guard Drawing 225-WLB-625-001 Rev G, Windows and Portlights

Coast Guard Drawing 225-WLB-805-015, Rev D, Scantlings, Decks & Platforms

Coast Guard Drawing 225-WLB-920-001, Rev F, Hull Block 920 Panels

Coast Guard Drawing FL 1204-003, Rev A, Welded Padeyes & Link

Coast Guard Drawing FL 1204-3. Rev A, Welded Padeyes and Links

Coast Guard Drawing FL-1602-89, Fleet 26x66 Weathertight door

Coast Guard Fleet Drawing FL 2804-12, Rev -, U.S.C.G. Emblem

Coast Guard Fleet Drawing FL 2804-22, Rev-, Consolidated Visual ID for Cutters

NAVSEA Drawing 803-5001104, Rev -; Rudder Stock Bearings and Seals

NAVSEA Drawing 805-1624093, Rev J, Scuttle, WT, Raised, Quick Acting, 21” Dia

NAVSEA Dwg 803-1385664, Bearings, Stern Tube & Strut

NAVSEA Dwg 803-2145807, Propulsion Shafting & Components

COAST GUARD PUBLICATIONS

Coast Guard Commandant Instruction (COMDTINST) 9077.1 (series), Equipment Lockout/Tags-Plus Instruction

Coast Guard Commandant Instruction (COMDTINST) M10360.3, Jun 2006, Coatings and Colors Manual

Coast Guard Drawing 225 WLB 633-001, Rev F, Cathodic Protection System Arrangement, Block Diagram, Wiring Deck Plan, and Elementary Diagrams

Coast Guard Technical Publication (CGTP) 3555, SWBS 561, Section A, Jan 2021, Steering Gear System- Model 990192-1

Coast Guard Technical Publication (TP) 3498, Section A, Jul 2015, Buoy Chain Winch

Coast Guard Technical Publication (TP) 3498, SWBS 573, Feb 2021, Buoy Chain Winch

Coast Guard Technical Publication (TP) 3523, Apr 2002, SWBS 241-A, Reduction Gear - Model 96DHCMG-Cp

Coast Guard Technical Publication (TP) 3523, SWBS 241-A, Nov 2007, Reduction Gear - Model

96DHCMG-CP

Coast Guard Technical Publication (TP) 3523-241-A&B, 225 WLB MIB, VOL 5, SWBS 241, GEAR, REDUCTION, MMC PN 241-01-01

Coast Guard Technical Publication (TP) 3523-242-A-C, 225 WLB MIB, SWBS 242, Coupling, Torsional, MMC PN 242-01-01 & 242-01-02

Coast Guard Technical Publication (TP) 3524, 2013, Manufacturer's Instruction Book-SWBS Group(s) 243-262

Coast Guard Technical Publication (TP) 3524, 07-JAN-97, Manufacturer's Instruction Book-SWBS Group(s) 243-262

Coast Guard Technical Publication (TP) 3524, May 2009, Manufacturers Instruction Book, SWBS Group(s) 243-262, 225’ WLB Class Cutters, SWBS 243, Section A, Seal, Forward Stern Shaft, Manufacturer: John Crane, Model NO. MB Series, Rev. 1 xi (Rev-0)

Coast Guard Technical Publication (TP) 3524, SWBS 245-A, Apr 2000, Instruction Manual for the Model 102 A Class Controllable Pitch Propeller and Shafting System

Coast Guard Technical Publication (TP) 3524, SWBS 245-A, May 2009, Propeller System, CPP - Model

Coast Guard Technical Publication (TP) 3524-244-A, 225 WLM MIB, SWBS 244-A, Bearing, Line Shaft, MMC PN 244-01-03, TP 244-A

Coast Guard Technical Publication (TP) 3524-245-A&B, 225 WLB, SWBS 245-A & 245-B, Propeller System, CPP, MMC PN 245-01-01, 0

Coast Guard Technical Publication (TP) 3529B, Manufacturer's Information Book – SWBS Group(s) 310

Coast Guard Technical Publication (TP) 3530B, Manufacturer's Instruction Book – SWBS Group(s) 310

Coast Guard Technical Publication (TP) 3555, 21-May-1996, Steering Gear Systems

Coast Guard Technical Publication (TP) 3556, Jul 2020, SWBS 568, Section E, Bow and Stern Thruster – Model 125/3 STAY/FP

Coast Guard Technical Publication (TP) 3556, Manufacturer's Instruction Book – SWBS Group(s) 568

Coast Guard Technical Publication (TP) 3559, SWBS 581A, Anchor Windlass, P/S - Model BMD-389

Coast Guard Technical Publication (TP) 3574, Mar 2009, SWBS Group 633-638

Coast Guard Technical Publication (TP) 3574, May 1996, Manufacturer's Instruction Book-SWBS Group(s) 633-638

Coast Guard Technical Publication (TP) 3943, Twin Pivot Arm Davit - Type Tw.Piv 5.0B - Ref. No.

5558-l Thru 5558-15

Coast Guard Technical Publication (TP) 5029, 01-NOV-03, S9243-Bx-MMC-010 - Bulkhead Shaft Seal

Fire Prevention and Response

NAVSEA Dwg 2803-980209, Plates, Label

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 0450, 2022, Electrical Power for Contractor’s Tools & Equipment

Surface Forces Logistics Center Standard Specification (SFLC Std Spec) 3100, 2022, Inspect, Test and Recondition AC Synchronous Machines In-Place

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2022, General Requirements

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), Jan 2022, General Requirements

Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), Latest Version, General Requirements

Surface Forces Logistics Center Standard Specification 0450 (SFLC Std Spec 0450), 2022, Electrical Power for Contractor’s Tools & Equipment

Surface Forces Logistics Center Standard Specification 0450 (SFLC Std Spec 0450), 2022, Electrical Power for Contractor's Tools & Equipment

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2022, Requirements for Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2022, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2022, Welding and Allied Processes.

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), Jan 2022, Welding and Allied Processes xii (Rev-0)

Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), Latest Version, Welding and Allied Processes

Surface Forces Logistics Center Standard Specification 0850 (SFLC Std Spec 0850), Jun 2022, General Requirements for Drawing Preparation

Surface Forces Logistics Center Standard Specification 3020 (SFLC Std Spec 3020), 2022, Overhaul AC Electrical Motors

Surface Forces Logistics Center Standard Specification 3041 (SFLC Std Spec 3041), 2022, Shipboard Electrical Cable Test

Surface Forces Logistics Center Standard Specification 3042 (SFLC Std Spec 3042), 2022, Shipboard Electrical Cable Removal, Relocation, Splice, Repair, and Installation

Surface Forces Logistics Center Standard Specification 3100 (SFLC Std Spec 3100), 2022, Inspect, Test and Recondition AC Synchronous Machines In-Place

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2022, Auxiliary Machine Systems Installation Details

Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2022, Auxiliary Machine Systems

Surface Forces Logistics Center Standard Specification 5550 (SFLC Std Spec 5550), 2022, Fire Prevention and Response

Surface Forces Logistics Center Standard Specification 5550 (SFLC Std Spec 5550), Latest Version, Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2022, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2022, Requirements for Preservation of Ships Structures

Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), Latest Version, Requirements for Preservation of Ship Structures

Surface Forces Logistics Center Standard Specification 8634 (SFLC Std Spec 8634), 2022, Drydocking

Surface Forces Logistics Center Standard Specification 8635 (SFLC Std Spec 8635), 2022, Temporary Services

Surface Forces Logistics Center Standard Specification 8636 (SFLC Std Spec 8636), 2022, Temporary Hull Accesses

Surface Forces Logistics Center Technical Standard (SFLC TS) 305, 2022, Electrical and Electronic Designating and Marking

OTHER REFERENCES

A-A-59323, Rev -; CLOTHS, CLEANING, LOW-LINT , 6/30/99

American Bureau of Shipping (ABS) Approved Chain, Accessory and Bar Manufacturing Facilities List, Oct 2016

American National Standards Institute/American Water Works Association (ANSI/AWWA) C652, 2011, Disinfection of Water-Storage Facilities

American National Standards Institute/NSF International (ANSI/NSF) 61, 2008, Drinking Water System Components - Health Effects

American National Standards Institute/NSF International (ANSI/NSF) 61, 2015, Drinking Water System Components - Health Effects

American Society of Mechanical Engineers (ASME) B16.34, 2004, Valves-Flanged, Threaded, and Welding End xiii (Rev-0)

American Society of Mechanical Engineers (ASME) B16.34, 2017, Valves-Flanged, Threaded, and Welding End

ASTM International (ASTM) D1330, 2004, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D1330, 2010, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D1330, 2015, Standard Specification for Rubber Sheet Gaskets

ASTM International (ASTM) D3359, 2009, Standard Test Methods for Measuring Adhesion by Tape Test

ASTM International (ASTM) D4138, 2013, Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means

ASTM International (ASTM) D5363, 2008, Standard Specification for Anaerobic Single Component Adhesives (An)

ASTM International (ASTM) D5363, 2016, Standard Specification for Anaerobic Single-Component Adhesives (AN)

ASTM International (ASTM) F683, 2014, Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery

ASTM International (ASTM) F992, 2006, Standard Specification for Valve Label Plates

ASTM International (ASTM) F992, 2017, Standard Specification for Valve Label Plates

Coast Guard Commandant Instruction (COMDTINST) M10360.3, Jun 2006, Coatings and Colors Manual

Code of Federal Regulations (CFR) Title 29, Part 1910, Occupational Safety and Health Standards

Code of Federal Regulations (CFR) Title 29, Part 1915, Occupational Safety and Health Standards for Shipyard Employment

Code of Federal Regulations (CFR) Title 29, Part 1915, Occupational Safety and Health Standards for Shipyard Employment

Code of Federal Regulations (CFR) Title 40, Protection of the Environment

COMDTINST M10360.3C, Coatings and Color Manual

Commercial Item Description (CID) A-A-59313, Nov 2003, Thread Compound; Anti-seize, Zinc Dust- Petrolatum

Commercial Item Description (CID) A-A-59588, 2013, Rubber Silicone

Commercial Item Description (CID), A-A-59323, Mar 2005, Cloths, Cleaning, Low-Lint

Commercial Item Descriptions (CID) A-A-59323, Rev A; Cloths, Cleaning, Low-Lint

Federal Specification (Fed Spec) QQ-N-281, Oct 1985, Nickel-Copper Alloy Bar, Rod, Plate, Sheet, Strip, Wire, Forgings, and Structural and Special Shaped Sections

Federal Specification (Fed Spec) RR-C-271, Rev E, Dec 2010, Chain and Attachments, Welded and Weldless

Federal Specification (Fed Spec) RR-C-271, Rev E, Mar 2016, Chains and Attachments, Carbon and Alloy Steel

Institute of Electrical and Electronics Engineers (IEEE), IEEE Std 45, Recommended Practice for Electrical Installations on Shipboard.

KVH Industries, MV103DG, Technical Manual User’s Guide Installation Guidelines, 54-0043-02 Rev A.

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-61, 2003 Edition, Pressure Testing Of Steel Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-61, 2013 Edition, Pressure Testing Of Steel Valves xiv (Rev-0)

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-67, 2002 Edition, Butterfly Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-67, 2017 Edition, Butterfly Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-72, 1999 Edition, Ball Valves with Flanged or Butt-Welding Ends for General Service

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS) SP-72, 2018 Edition, Ball Valves with Flanged or Butt-Welding Ends for General Service

Manufacturers' Standardization Society of the Valve and Fittings Industry (MSS) SP-80, 2008 Edition, Bronze Gate, Globe, Angle and Check Valves

Manufacturers' Standardization Society of the Valve and Fittings Industry (MSS) SP-80, 2013 Edition, Bronze Gate, Globe, Angle and Check Valves

Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), SP-58, 2018, Pipe Hangers and Supports – Materials, Design, Manufacture, Selection, Application and Installation

MIL PRF-16173, Sep 2006, Corrosion Preventive Compound, Solvent Cutback, Cold-Application

MIL-A-18001, May 2005, Anodes, Sacrificial Zinc Alloy (Commercially Accepted - ASTM B418)

MIL-A-22262, Mar 1996, Abrasive Blasting Media Ship Hull Blast Cleaning

MIL-A-22262, Mar 1996; Abrasive Blasting Media Ship Hull Blast Cleaning

MIL-C-24633, Oct 2014, Chain, Stud Link, Anchor, Low Alloy Steel, Flash Butt Welded

MIL-DTL-15024F, General Specification for Plates, Tags, and Bands for Identification of Equipment

MIL-DTL-23549, Sep 2016, Grease, General Purpose

MIL-DTL-24643(series), General Specification for Cables and Cords, Electric, Low Smoke, for Shipboard Use.

MIL-PRF-16173, 2006, Corrosion Prevention Compound, Solvent Cut-Back, Cold-Application

MIL-PRF-16173, Sep 2006, Corrosion Preventive Compound, Solvent Cutback, Cold-Application

MIL-PRF-24176, 2004, Cement, Epoxy, Metal Repair and Hull Smoothing (Metric)

MIL-PRF-24647, 2013, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-24647, Jan 2018, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-24647, Jun 2006, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-24647, Jun 2006, Paint System, Anticorrosive and Antifouling, Ship Hull

MIL-PRF-9000, Rev H; Lubricating Oil, Shipboard Internal Combustion Engine, High Output Diesel, 9/16/87

MIL-S-22473 , Rev E(8); Sealing, Locking, and Retaining Compounds: (Single Component), 01/21/04

MIL-S-45180, 1998, Sealing Compound, Gasket, Hydrocarbon Fluid and Water Resistant

MIL-S-45180, 1998; Sealing Compound, Gasket, Hydrocarbon Fluid and Water Resistant

Naval Sea Systems Command (NAVSEA) S9243-AW-TRS-011, Surface Ships Main Propulsion Shafting Refurbishment Procedures, Volume I, Part 1

Naval Sea Systems Command (NAVSEA) S9243-AW-TRS-012, Surface Ships Main Propulsion Shafting Examination, Test and Repair Action Record, Volume 1, Part 2

Naval Sea Systems Command (NAVSEA) Underwater Ship Husbandry Manuals (UWSH) S0600-AA- PRO-160, Nov 2011, Chapter 16, Cofferdams

Naval Sea Systems Command (NAVSEA) Underwater Ship Husbandry Manuals (UWSH) S0600-AA- PRO-160, Nov 2011, Chapter 16, Cofferdams xv (Rev-0)

Naval Ships' Technical Manual, Chapter 241, Propulsion Reduction Gears, Couplings, Clutches, and Associated Components

NAVSEA Drawing 804-5773931, Rev A, Acoustic & Thermal Insulation For Compartments Installation Details

NAVSEA Drawing 804-5773931, Rev-A, Insulation for Compartments, Acoustic and Thermal – Installation Details

NAVSEA Technical Publication T9074-AD-GIB-010/1688, (TP 1688), July 2012, Requirements for Fabrication, Welding, and Inspection of Submarine Structure

ODOM Echotrac DF3200 MKII, Rev 2, Technical Manual

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) C6183, 2019, Cork and Rubber Composition Sheet; For Aromatic Fuel and Oil Resistant Gaskets

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) C-6183B, 2019, Cork and Rubber Composition Sheet; for Aromatic Fuel and Oil Resistant Gaskets

Society of Automotive Engineers (SAE) Aerospace Material Specification (AMS) G-6032, 2022 Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric

Society of Automotive Engineers (SAE) AMS-G-6032, August 2012, Grease, Plug Valve, Gasoline and Oil Resistant, NATO Code Number G-363, Metric

The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 1 (SSPC-SP 1), 2004, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 1 (SSPC-SP 1), 2016, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No. 11 (SSPC-SP 11), 2007, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.1 (SSPC-SP 1), 2015, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.1 (SSPC-SP 1), 2016, Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.1 (SSPC-SP 1), Solvent Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2004, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2012, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2012, Power-Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2013, Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), Power Tool Cleaning to Bare Metal

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.3 (SSPC-SP 3), 2004, Power Tool Cleaning

The Society for Protective Coatings (SSPC) Surface Preparation Specification No.3 (SSPC-SP 3), Power Tool Cleaning)

The Society for Protective Coatings (SSPC), January 2015, Paint Application Specification No. 2 (PA-2), Procedure for Determining Conformance to Dry Coating Thickness Requirements xvi (Rev-0)

The Society for Protective Coatings (SSPC), Paint Application Specification No. 2 (PA-2), Procedure for Determining Conformance to Dry Coating Thickness Requirements

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, 2007, Near-White Metal Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No.2, 2007, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 12/NACE No.5, 2002, Surface Preparation and Cleaning of Metals by Waterjetting Prior to Recoating

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 6/NACE No. 3, 2007, Commercial Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP 7/NACE No.4, 2007, Brush-Off Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-2, 2012, Waterjet Cleaning of Metals – Very Thorough Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-2, 2012, Waterjet Cleaning of Metals – Very Thorough Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-2/NACE WJ-2, 2012, Waterjet Cleaning of Metals – Very Thorough Cleaning

The Society for Protective Coatings (SSPC)/NACE International (NACE) Joint Surface Preparation Standard SSPC-SP WJ-4/NACE WJ-4, 2012, Waterjet Cleaning of Metals – Light Cleaning

The Society for Protective Coatings (SSPC)/NACE Joint Surface Preparation Standard SSPC-SP 10/NACE No.2, 2004, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, 2004, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, 2007, Near-White Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation Standard SSPC-SP 10/NACE No. 2, 2007, Near-White Metal Blast Cleaning

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation Standard SSPC-SP 12/NACE No. SSPC-SP 12/NACE No.5, Surface Preparation and Cleaning of Steel & Other Hard Materials by High and Ultrahigh Pressure Water Jetting Prior to Recoating

The Society for Protective Coatings (SSPC)/NACE-International (NACE) Joint Surface Preparation Standard SSPC-SP 12/NACE No.5, Surface Preparation and Cleaning of Steel & Other Hard Materials by High and Ultrahigh Pressure Water Jetting Prior to Recoating

The Society for Protective Coatings (SSPC)-SP 3, Power Tool Cleaning, 11-1-2004

The Society for Protective Coatings SSPC-SP 10/NACE No.2, Jan 2007, Near-White Blast Cleaning

The Society for Protective Coatings SSPC-SP 10/NACE No.2, Near-White Blast Cleaning

The Society for Protective Coatings SSPC-SP 10/NACE No.2, Rev 7; Near-White Blast Cleaning

The Society for Protective Coatings SSPC-SP 11, Jul 2012, Power Tool Cleaning to Bare Metal xvii (Rev-0)

CONSOLIDATED LIST OF GOVERNMENT-FURNISHED PROPERTY

The following is a list of property, which the Government will furnish. This list supersedes any other material obligations indicated or implied by referenced drawings.

WORK

ITEM

MTI ITEM DESCRIPTION NSN/PN QTY ESTIMATED

COST

($/UNIT)

20 N HS pinion bearing, DWG 01070-0353 item

Philadelphia Gear Corporation P/N 31000-1017

2 3880

20 N HS pinion bearing, DWG 01070-0353 item

Philadelphia Gear Corporation P/N 31000-1018

2 1781

20 N HS pinion bearing, DWG 01070-0353 item

Philadelphia Gear Corporation P/N 31000-0475

2 1438

20 N HS pinion bearing, DWG 01070-0353item

Philadelphia Gear Corporation P/N 31000-0474

2 1129

20 N MDE end quill shaft bearing, DWG 01070-

0353 item 15

Philadelphia Gear Corporation P/N 31000-1047

2 1001

20 N PTO CPP bearing, DWG 01070-0353 item

Philadelphia Gear Corporation P/N 31000-1780

2 154

20 N ALOP bearing, DWG 01070-0353 item 63

Philadelphia Gear Corporation P/N 31000-1780

2 154

20 N LS shaft bearing DWG 01070-0353 Item 33

Philadelphia Gear Corporation P/N 31000-1777

1 13552

20 N LS shaft bearing DWG 01070-0353 Item 59

Philadelphia Gear Corporation P/N 31000-1778

1 6856

20 N Clutch end quill shaft bearing DWG 01070-

0353 Item 27

Philadelphia Gear Corporation P/N 31000-1779

2 198

20 N Turning Gear/Generator Pinion Bearing DWG 01070-0353 Item 74

Philadelphia Gear Corporation P/N 31000-1795

1 1471

20 N Turning Gear/Generator Pinion Bearing DWG 01070-0353 Item 75

Philadelphia Gear Corporation P/N 31000-1796

1 616

20 N Turning Gear/Generator Pinion Bearing DWG 01070-0353 Item 76

Philadelphia Gear Corporation P/N 31000-0224

1 964

20 N Turning Gear/Generator Pinion Bearing DWG 01070-0353 Item 77

Philadelphia Gear Corporation P/N 31000-0223

1 803

20 N Oil Seal Dwg 010170- 0317; 408

P/N 36000-0409 2 78

20 N Plate, Seal Dwg P/N 34000-8834 1 400 xviii (Rev-0)

010170-0317;426

DH1259K-4

20 N Oil Seal Dwg 010170- 0317; 431

P/N 36000-2344 1 29

20 N Gasket Dwg 010170-

0317; 449 DH25K

P/N 34000-8742 1 11

20 N Oil Seal Dwg 010170- 0317; 450

P/N 36000-1279 1 13

20 N Seal, Oil Dwg 010170- 0353; 11

P/N 36000-0049 4 104

20 N Seal, Oil Dwg 010170- 0353; 12

P/N 36000-2541 2 126

20 N Spacer, Oil Dwg 010170-0353; 14

P/N 50315-9672 2 591

20 N Retainer, Seal Dwg 010170-0353; 16

P/N 50085-3146 2 385

20 N Seal, Oil Dwg 010170- 0353; 20

P/N 36000-2277 2 60

20 N Spacer, Seal Dwg 010170-0353; 21

P/N 50315-9030 2 1199

20 N Seal, Oil Dwg 010170- 0353; 22

P/N 36000-1752 2 368

20 N Spacer, Seal Dwg 010170-0353; 35

P/N 50315-9031 1 1185

20 N Oil Seal Dwg 010170- 0353; 36

P/N 3600-1231 2 368

20 N Retainer, Seal Dwg 010170-0353; 47

P/N 50085-3186 1 400

20 N Retainer, Seal Dwg 010170-0353; 49

P/N 50085-2850 1 400

20 N Oil Seal Dwg 010170- 0353; 55

P/N 36000-1531 2 104

20 N Spacer, Seal Dwg 010170-0353; 56

P/N 50315-9032 1 934

20 N Oil Seal Dwg 010170- 0353; 80

P/N 36000-0739 2 35

20 N Spacer, Seal DWG 010170-0353; 81

P/N 50315-9033 1 471

20 N O-Ring DWG 010170- 0353; 96

P/N 36000-1760 1 2

20 N Gasket DWG 010170- 0353; 98

P/N 40225-0562 2 29

20 N Seal DWG 010170- 0353; 307

P/N 36000-0030 1 40

20 N Seal DWG 010170- 0353; 311

P/N 50085-2865 1 330

20 N Gasket DWG 010170- 0109; 609

P/N 36000-1788 3 30

20 N Gasket DWG 010170- P/N 36000-1957 3 33 xix (Rev-0)

0131; 277 20 N Gasket DWG 010170-

0131; 516 P/N 36000-1786 4 25

20 N DWG 010170-0131;

P/N 36000-1958 2 45

20 N Gasket DWG 010170- 0131; 546

P/N 36000-2662 1 25

20 N Gasket DWG 010170- 0131; 556

P/N 36000-1787 1 25

20 N Gasket DWG 010170- 0131; 565

P/N 36000-1788 1 30

20 N Gasket DWG 010170- 0131; 501

P/N 36000-1956 6 167

20 N Set of 12 Pads (shoes) for Thrust Bearing

Philadelphia Gear Corporation P/N 000010188000

1 9,986

20 N Complete Turning Gear Philadelphia Gear Drawing 01070-0353

1 30,000

21 Y **Propeller shaft NSN: 2010-01-399-5912 1ea. 165,000 21 N **Grounding Silver

Strip NSN: 5340-01-126-4569 1ea. 1,889

21 N **SST Straps NSN: 5340-01-126-4570 4ea. 28 21 N **SST Bailing Seals NSN: 5330-01-284-3686 4ea. 6 22 N 225' WLB Major

Overhaul Kit NSN: 5330-01-520-5284 1 ea. 35,249.00

22 N **225' WLB Seat (Split)

NSN: 5330-01-645-3665 1 ea. 12,500.00

22 Y *Seal Compression Tool

Onboard Tool 1 ea. 200.00

23 N **Oversized shaft seal diaphragm (Main Prop

Shaft)

NSN: 2010-01-537-2301 2 ea. 9,828.00

23 N **Oversized shaft seal diaphragm (PTO shaft)

PN: H74265-01-3 1 ea. 4,250.00

23 N **Entire New Seal (Main Prop Shaft)

NSN: 2040-01-393-7061 2 ea. 18,883.00

30 Y **Blade Bolts NSN: 5306-01-410-6893 4 ea. 1,854.12 30 N Blade Bolt O-rings NSN: 5330-01-408-7251 PN:

0-3-2-1 48 ea. 2.25

30 N Blade Seal NSN: 5331-01-623-0621 PN:

2-472 KA174-75

4 ea. 55.00

30 Y *Lifting Device, Propeller Blade

NSN: 2020-01-F02-6825 1 ea. 100.00

36 N *** Fathometer Transducer, shallow water, 50-200 kHz

(Airmar Technology

SS505)

NSN: 5845-01-518-7231 PN:

SS505

2 ea. 343.63

36 Y ***Fathometer Transducer, Deep

NSN: 5845-01-496-9770 PN:

TH28/20-41-516CG

1 ea. $7,709.21 xx (Rev-0)

Water, 24kHZ 45 N **Upper bearing NSN: 3110-01-466-9924 1 ea. 10,525.45 45 N Rudder Seal Kit NSN: 5330-01-565-8083 1 ea. 2,433.76 46 N Lower bearing NSN: 3120-21-912-7635 1 ea. 6,661.26 46 N Pintle bearing NSN: 3120-21-912-7634 1 ea. 3,380.38 47 N Seal Kit, Thruster NSN: 2010-01-555-9048 2 ea. $4,280.00 47 N **Seal Spacer NSN: 5365-01-495-6823 2 ea. $700.00 47 N **Shaft Sleeve NSN: 2010-01-495-2638 2 ea. $5702.40 68 N Reference electrode, silver & silver chloride NSN: 5977-01-346-0750 2 ea. 1,300.02

69 Y *Transducer Cover Plate

N/A 4 ea. 50.00

72 N Coast Guard (C-G) P/N

CGRD50TDRASS01

Assembly of bowl, D- Ring and strap. Rated

Load 12,300 lbs.

NSN# 2020-01-682-7587 10 $150

76 Y Welin Lambie TWPIV5.0 Davit

NSN: 2030-99-454-8999 PN:

5558 Series

1 ea. 634,362.51

76 N TWPIV5.0B Portside Conversion Kit

NSN: 2030-01-F15-4212 PN:

892-02076

1 ea. 28,249.40

77 N Coast Guard (C-G)

CGDR50TDRASS01

Flush Pad-eye Assembly: Coast Guard

(C-G) CGDR50T01

(NSN# 5365-01-612-

1273) D-Ring (Rated

Load 12,300 lbs), welded strap, fabricated bowl

NSN# 2020-01-682-7587 24

79 N Heading Sensor, Processor Box

(Fluxmeter)

NSN: 6625-01-514-3574 PN:

02-0400-02

1 ea. 5,210.00

79 N Display Assembly NSN: 5980-01-676-1704 PN:

02-0401-01

1 ea. 1,201.46

79 N Junction Box Assembly (Interconnecting Box)

NSN: 5895-01-514-2455 PN:

02-0402-02

1 ea. 3,039.00

79 N Power Cable, w/ conn NSN: 5995-01-373-3391 PN:

32-0309-15

1 ea. 1,305.41

79 N Data Cable, w/ conn NSN: 6150-01-F20-6013 PN:

32-0308-15

1 ea. 1,045.00

79 N Sensor Cable, w/ conn NSN: 5995-01-373-3390 PN:

32-0313-25

1 ea. 2,535.10

79 N Extension Cable, Remote Display, w/ conn

NSN: 6450-01-F20-6014 PN:

32-0316-25

1 ea. 1,392.00

79 N Power Supply, 24VDC NSN: 6130-01-490-7110 PN:

24WB125

1 ea. 210.00 xxi (Rev-0)

81 N 30†x 30†Raised Watertight Hatch, 12†raised combing, 8 dogs, w/ installed

21†Quick Acting Watertight Scuttle

2 ea. $3500

82 N Quick Acting Watertight Steel Door 26†x66†, Left

Hand, 10 Dog w/ hasp and staple. 9†diameter fixed light

1 ea. $4000

84 N Steel WTRTD, 26" X 66"; 10 dog; RH;

w/14"x18" C.O.

Window, Lever type knobs & Mortise lock

USCG DWG FL-1602-89 1 ea $4500

84 N Steel WTRTD, 26" X 66"; 10 dog; LH;

w/14"x18" C.O.

Window, Lever type knobs & Mortise lock

USCG DWG FL-1602-89 1 ea $4500

85 N Directional Control Valve (DCV)

NSN: 4810-01-F19-5719 PN:

4WRE10E75-2X/G24K4/V

1 ea. 1137.00

85 N Amplifier Card NSN: 5996-01-F19-5720 PN:

VT-VRPA2-2-1X/V0/T1

1 ea. 958.21

85 N Amplifier Card Holder NSN: 5996-01-F19-5721 PN:

VT3002-1-2X/48F

1 ea. 367.50

85 N Mating Connector, 4P

G4WIF PG7 SW

NSN: 5935-01-F19-5722 PN:

R900023126

1 ea. 150.00

91 N Siemens CPU 1214 NSN: 7042-01-693-4330 PN:

6ES7214-1AG40-0XB0

2 ea. 400.00

91 N Siemens Memory Card, S7-1200, 4MB

NSN: 7050-12-414-4763 PN:

6ES7954-8LC03-0AA0

2 ea. 60.00

91 N Siemens Expansion Module, S7-1200, 8 DI, 8 DO

NSN: 5998-01-693-4347 PN:

6ES7223-1BH32-0XB0

2 ea. 255.00

*Government-loaned property, which shall be returned to the vessel upon completion of the availability.

**New or refurbished equipment that the Government may provide for installation in place of existing equipment.

***Government-furnished property, which is to be supplied by either the vessel or the C4IT ServiceCenter xxii (Rev-0)

CONSOLIDATED LIST OF CRITICAL INSPECTION ITEMS

The following is a list of work items, which contain Critical Inspection reports, which the Contractor must complete within the first 25% of the availability contract period (see SFLC Std Spec 0000, paragraph 3.2.6.5 (Inspection report particulars)):

Work Item

Title

3 Hull Plating, U/W Body, Ultrasonic Testing

5 U/W Body, Preserve, 100 percent

11 Appendages, U/W, Leak Test

15 Voids, Non-Accessible, Leak Test

21 Propulsion Shafting; Remove, Inspect, and Reinstall

22 Propulsion Shaft Seals, Mechanical Overhaul And Inflatable Renewal

23 Propulsion Shaft Seals, Bulkhead, Overhaul

26 Propulsion Shaft Bearings, External, Check Clearances

29 Controllable Pitch Propellers, Clean and Inspect

30 Controllable Pitch Propeller Hub, General Maintenance with EAL, Perform

37 Sea Strainers, Duplex, All Sizes, Overhaul

38 Sea Strainers, Simplex, All Sizes, Clean and Inspect

39 Sea Bay, Clean and Inspect

42 Rudder Stock Bearings, Check Clearances

43 Rudder, Inspect And Repair

44 Rudder and Rudder Stock, Remove and Inspect

47 Thruster Generator, Clean & Inspect

48 Anchor Windlass, Inspect and Service

49 Anchor Chains and Ground Tackle, Inspect and Repair

66 Impressed Current Cathodic Protection System, Inspect and Maintain

68 Drydock xxiii (Rev-0)

71 ATON Tie Down Installation

72 Compartment Insulation, General, Renew

74 Space or Component, Preserve

75 Welin Lambie Dual Point Davit TWPIV 5.0B, Renew

84 Directional Control Valve, Upgrade

85 Pilot House Windows and Frame, Repair and Reseal

86 Tanks, MP Fuel Stowage and Overflow, Clean and Inspect

88 Potable Water Pump Room Deck, Preserve

90 Steering System PLC, Upgrade xxiv (Rev-0)

PRINCIPAL CHARACTERISTICS

225' WLB (A-CLASS)

PHYSICAL

Length overall 225' 0" Length between perpendiculars 206' 0" Maximum beam 46' Designed draft 13' 0" Full load displacement 1929.74 Long Tons SW Light ship displacement 1544.38 Long Tons SW Minimum operating displacement 1906.70 Long Tons SW Mast height (above 12' waterline) 67' 5" Anchor Two 4000 lb standard Navy stockless anchors, 8 shots each, port and starboard, 1-

3/8 die lock chain

HULL

Bilge keels (port & starboard) Frames 42-79 Frame spacing FR 0 to 12 21" FR 12 to 30 22" FR 30 to 102 24"

MACHINERY

Main propulsion Diesel Reduction Diesel engines Two Caterpillar 3608, TA, 3100 BHP each @ 900 RPM Number of propellers 1 Number of blades 4 Diameter 10' Pitch Controllable

RPM 254

Ship's service diesel generators Two Caterpillar 3508 TA, 450 KW Emergency diesel generator One Caterpillar 3406 DITA, 280 KW Shore tie Two 450 VAC, 400 Amp, 3-wire Shaft bearing, forward Cooper Bearing 01-BCP-1400-EX-TL Shaft bearing, aft Water Lubricated Cutless Bearing

TANK CAPACITIES

Diesel oil 76,498 gal.

Fresh water capacity 8056 gal.

Hydraulic oil capacity 2785 gal.

Lube oil storage 764 gal.

Grey water tank 2700 gal.

Sewage holding tank 1700 gal.

1 (Rev-0)

00000_0824_FLT

REC_00000_FLT_Commercial Project @ Contractor’ Facility (0121)

General Requirements

1. SCOPE

1.1 Intent. This standard specification invokes general requirements for conducting vessel repairs performed at a commercial contractor’s facility for Coast Guard vessels.

1.2 Term interchangeability. The terms 'Contractor', 'CG Yard', 'NAVSTA EVERETT', 'shipyard', 'Base', and 'Coast Guard Industrial' are used interchangeably in this specification.