JOC_Central_Region_Book_3.pdf

STATE OF CALIFORNIA DEPARTMENT OF GENERAL SERVICES

REAL ESTATE SERVICES DIVISION

PROJECT MANAGEMENT AND DEVELOPMENT BRANCH

PROJECT MANUAL – Book 3 of 3

BOOK 1

DIVISION 00 & 01 SPECIFICATIONS

BOOK 2

JOB ORDER PRICE PROPOSAL SAMPLE

JOB ORDER SAMPLE DOCUMENTS

UNIT PRICE CATALOG (UPC)

BOOK 3

TECHNICAL SPECIFICATIONS

FOR:

JOB ORDER CONTRACT – CENTRAL REGION

DEPARTMENT OF GENERAL SERVICES

CALIFORNIA

Juli Kawahata, Capital Outlay Program Manager West Sacramento, California

Consultants: Facility Optimization Solutions, LLC (FOS)

AUGUST 2026

#000000000014572

Job Order Contracting Technical Specifications

Prepared for: CA DGS Central

Version: 8-3-2026

Printed: July 10, 2026

©2026 Facility Optimization Solutions, LLC All Rights Reserved

Simplebid® Specifications

Simplebid® Central

CADGS - Technical Specifications

CA-TS-01 1

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

TABLE OF CONTENTS

PROCUREMENT AND CONTRACTING REQUIREMENTS GROUP

DIVISION 00 – PROCUREMENT AND CONTRACTING REQUIREMENTS

INTRODUCTORY INFORMATION

00 01 10 Table of Contents

SPECIFICATIONS GROUP

GENERAL REQUIREMENTS SUBGROUP

DIVISION 01 - GENERAL REQUIREMENTS

01 00 00 GENERAL REQUIREMENTS

FACILITY CONSTRUCTION SUBGROUP

DIVISION 02 - EXISTING CONDITIONS

02 41 16 STRUCTURE DEMOLITION

02 41 19 SELECTIVE DEMOLITION

02 42 96 HISTORIC REMOVAL AND DISMANTLING

02 87 16.13 BIRD EXCREMENT REMOVAL

DIVISION 03 - CONCRETE

03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE

03 10 00 CONCRETE FORMING AND ACCESSORIES

03 20 00 CONCRETE REINFORCING

03 30 00 CAST-IN-PLACE CONCRETE

03 33 00 ARCHITECTURAL CONCRETE

03 35 43 POLISHED CONCRETE FINISHING

03 37 13 SHOTCRETE

03 38 16 UNBONDED POST-TENSIONED CONCRETE

03 41 00 PRECAST STRUCTURAL CONCRETE

03 45 00 PRECAST ARCHITECTURAL CONCRETE

03 47 13 TILT-UP CONCRETE

03 49 00 GLASS-FIBER-REINFORCED CONCRETE

(GFRC)

03 51 13 CEMENTITIOUS WOOD FIBER DECKS

03 52 16 LIGHTWEIGHT INSULATING CONCRETE

03 53 00 CONCRETE TOPPING

03 54 13 GYPSUM CEMENT UNDERLAYMENT

03 54 16 HYDRAULIC CEMENT UNDERLAYMENT

DIVISION 04 - MASONRY

04 01 10 MASONRY CLEANING

04 01 20.63 BRICK MASONRY REPAIR

04 01 20.64 BRICK MASONRY REPOINTING

CADGS - Technical Specifications

CA-TS-01 2

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

04 01 40.61 STONE REPAIR

04 01 40.62 STONE REPOINTING

04 03 10 HISTORIC MASONRY CLEANING

04 03 22 HISTORIC BRICK UNIT MASONRY REPAIR

04 03 23 HISTORIC BRICK UNIT MASONRY REPOINTING

04 03 26 HISTORIC TERRA COTTA UNIT MASONRY

REPAIR

04 03 27 HISTORIC TERRA COTTA UNIT MASONRY

REPOINTING

04 03 36 HISTORIC TREATMENT OF ADOBE MASONRY

04 03 42 HISTORIC STONE MASONRY REPAIR

04 03 43 HISTORIC STONE MASONRY REPOINTING

04 03 45 HISTORIC STONE CONSOLIDATION

TREATMENT

04 20 00 UNIT MASONRY

04 22 00 CONCRETE UNIT MASONRY

04 23 00 GLASS UNIT MASONRY

04 26 13 MASONRY VENEER

04 42 00 EXTERIOR STONE CLADDING

04 43 13.13 ANCHORED STONE MASONRY VENEER

04 43 13.16 ADHERED STONE MASONRY VENEER

04 72 00 CAST STONE MASONRY

DIVISION 05 - METALS

05 01 70.51 DECORATIVE METAL CLEANING

05 01 70.52 DECORATIVE METAL CLEANINGS

05 01 70.53 DECORATIVE METAL CLEANINGSS

05 01 70.61 DECORATIVE METAL REPAIR

05 01 70.63 DECORATIVE METAL REFINISHING

05 03 71 HISTORIC DECORATIVE METAL CLEANING

05 03 72 HISTORIC DECORATIVE METAL REPAIR

05 03 73 HISTORIC DECORATIVE METAL REFINISHING

05 03 74 HISTORIC DECORATIVE METAL REPLICATION

05 03 83 HISTORIC CAST IRON REPAIR

05 03 85 HISTORIC TREATMENT OF DECORATIVE

FORMED METAL

05 03 87 HISTORIC TREATMENT OF METAL SCULPTURE

05 12 00 STRUCTURAL STEEL FRAMING

05 12 13 ARCHITECTURALLY EXPOSED STRUCTURAL

STEEL FRAMING

05 21 00 STEEL JOIST FRAMING

05 31 00 STEEL DECKING

05 40 00 COLD-FORMED METAL FRAMING

05 44 00 COLD-FORMED METAL TRUSSES

05 50 00 METAL FABRICATIONS

05 51 13 METAL PAN STAIRS

05 51 16 METAL FLOOR PLATE STAIRS

05 51 19 METAL GRATING STAIRS

CADGS - Technical Specifications

CA-TS-01 3

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

05 52 13 PIPE AND TUBE RAILINGS

05 53 13 BAR GRATINGS

05 53 16 PLANK GRATINGS

05 53 19 EXPANDED METAL GRATINGS

05 58 13 COLUMN COVERS

05 58 19 HEATING/COOLING UNIT COVERS

05 59 63 DETENTION ENCLOSURES

05 70 00 DECORATIVE METAL

05 71 00 DECORATIVE METAL STAIRS

05 71 13 FABRICATED METAL SPIRAL STAIRS

05 73 00 DECORATIVE METAL RAILINGS

05 73 13 GLAZED DECORATIVE METAL RAILINGS

05 75 00 DECORATIVE FORMED METAL

DIVISION 06 - WOOD, PLASTICS, AND COMPOSITES

06 03 12 HISTORIC WOOD REPAIR

06 10 00 ROUGH CARPENTRY

06 13 00 HEAVY TIMBER CONSTRUCTION

06 15 16 WOOD ROOF DECKING

06 15 33 WOOD PATIO DECKING

06 16 00 SHEATHING

06 17 15 ENGINEERED STRUCTURAL WOOD

06 17 53 SHOP-FABRICATED WOOD TRUSSES

06 18 00 GLUED-LAMINATED CONSTRUCTION

06 20 13 EXTERIOR FINISH CARPENTRY

06 20 23 INTERIOR FINISH CARPENTRY

06 40 13 EXTERIOR ARCHITECTURAL WOODWORK

06 40 23 INTERIOR ARCHITECTURAL WOODWORK

06 41 00 ARCHITECTURAL WOOD CASEWORK

06 41 01 ARCHITECTURAL WOOD CASEWORK (NAAWS)

06 42 14 STILE AND RAIL WOOD PANELING

06 42 16 FLUSH WOOD PANELING

06 42 19 PLASTIC-LAMINATE-FACED WOOD PANELING

06 44 00 ORNAMENTAL WOODWORK

06 64 00 PLASTIC PANELING

06 74 13 FIBERGLASS REINFORCED GRATINGS

DIVISION 07 - THERMAL AND MOISTURE PROTECTION

07 01 50.19 PREPARATION FOR REROOFING

07 11 13 BITUMINOUS DAMPPROOFING

07 13 26 SELF-ADHERING SHEET WATERPROOFING

07 13 53 ELASTOMERIC SHEET WATERPROOFING

07 13 54 THERMOPLASTIC SHEET WATERPROOFING

07 14 13 HOT FLUID-APPLIED RUBBERIZED ASPHALT

WATERPROOFING

07 14 16 COLD FLUID-APPLIED WATERPROOFING

07 16 13 POLYMER MODIFIED CEMENT

WATERPROOFING

CADGS - Technical Specifications

CA-TS-01 4

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

07 16 16 CRYSTALLINE WATERPROOFING

07 16 19 METAL OXIDE WATERPROOFING

07 17 00 BENTONITE WATERPROOFING

07 18 00 TRAFFIC COATINGS

07 19 00 WATER REPELLENTS

07 21 00 THERMAL INSULATION

07 21 19 FOAMED-IN-PLACE INSULATION

07 24 13 POLYMER-BASED EXTERIOR INSULATION AND

FINISH SYSTEM (EIFS)

07 24 19 WATER-DRAINAGE EXTERIOR INSULATION

AND FINISH SYSTEM (EIFS)

07 25 00 WEATHER BARRIERS

07 26 00 VAPOR RETARDERS

07 27 13 MODIFIED BITUMINOUS SHEET AIR BARRIERS

07 27 15 NONBITUMINOUS SELF-ADHERING SHEET AIR

BARRIERS

07 27 26 FLUID-APPLIED MEMBRANE AIR BARRIERS

07 31 13 ASPHALT SHINGLES

07 31 16 METAL SHINGLES

07 31 26 SLATE SHINGLES

07 31 29 WOOD SHINGLES AND SHAKES

07 32 13 CLAY ROOF TILES

07 32 16 CONCRETE ROOF TILES

07 41 13.13 FORMED METAL ROOF PANELS

07 41 13.16 STANDING-SEAM METAL ROOF PANELS

07 41 13.19 BATTEN-SEAM METAL ROOF PANELS

07 41 16 INSULATED METAL ROOF PANELS

07 42 13.13 FORMED METAL WALL PANELS

07 42 13.16 METAL PLATE WALL PANELS

07 42 13.19 INSULATED METAL WALL PANELS

07 42 13.23 METAL COMPOSITE MATERIAL WALL PANELS

07 42 46 CEMENTITIOUS WALL PANELS

07 42 93 SOFFIT PANELS

07 46 16 ALUMINUM SIDING

07 46 19 STEEL SIDING

07 46 24 WOOD SHINGLE AND SHAKE SIDING

07 46 33 PLASTIC SIDING

07 46 46 FIBER-CEMENT SIDING

07 51 13 BUILT-UP ASPHALT ROOFING

07 51 16 BUILT-UP COAL TAR ROOFING

07 52 13 ATACTIC-POLYPROPYLENE (APP) MODIFIED

BITUMINOUS MEMBRANE ROOFING

07 52 16 STYRENE-BUTADIENE-STYRENE (SBS)

MODIFIED BITUMINOUS MEMBRANE ROOFING

07 53 16 CHLOROSULFONATE-POLYETHYLENE (CSPE)

ROOFING

07 53 23 ETHYLENE-PROPYLENE-DIENE-MONOMER

(EPDM) ROOFING

CADGS - Technical Specifications

CA-TS-01 5

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

07 54 16 KETONE ETHYLENE ESTER (KEE) ROOFING

07 54 19 POLYVINYL-CHLORIDE (PVC) ROOFING

07 54 23 THERMOPLASTIC-POLYOLEFIN (TPO)

ROOFING

07 55 52.13 ATACTIC-POLYPROPYLENE (APP) MODIFIED

BITUMINOUS PROTECTED MEMBRANE

ROOFING

07 55 52.16 STYRENE-BUTADIENE-STYRENE (SBS)

MODIFIED BITUMINOUS PROTECTED

MEMBRANE ROOFING

07 55 56 FLUID-APPLIED PROTECTED MEMBRANE

ROOFING

07 57 00 COATED FOAMED ROOFING

07 61 00 SHEET METAL ROOFING

07 62 00 SHEET METAL FLASHING AND TRIM

07 71 00 ROOF SPECIALTIES

07 71 29 MANUFACTURED ROOF EXPANSION JOINTS

07 72 00 ROOF ACCESSORIES

07 72 53 SNOW GUARDS

07 72 73 VEGETATED ROOF SYSTEMS

07 81 00 APPLIED FIRE PROTECTION

07 81 23 INTUMESCENT FIRE PROTECTION

07 82 00 BOARD FIRE PROTECTION

07 84 13 PENETRATION FIRESTOPPING

07 84 43 JOINT FIRESTOPPING

07 91 00 PREFORMED JOINT SEALS

07 92 00 JOINT SEALANTS

07 92 19 ACOUSTICAL JOINT SEALANTS

07 95 13.13 INTERIOR EXPANSION JOINT COVER

ASSEMBLIES

07 95 13.16 EXTERIOR EXPANSION JOINT COVER

ASSEMBLIES

07 95 13.19 PARKING DECK EXPANSION JOINT COVER

ASSEMBLIES

DIVISION 08 - OPENINGS

08 01 52.61 WOOD WINDOW REPAIRS

08 03 14 HISTORIC TREATMENT OF WOOD DOORS

08 03 51.23 HISTORIC TREATMENT OF STEEL WINDOWS

08 03 51.33 HISTORIC TREATMENT OF ALUMINUM

WINDOWS

08 03 52 HISTORIC TREATMENT OF WOOD WINDOWS

08 11 13 HOLLOW METAL DOORS AND FRAMES

08 11 16.13 INTERIOR ALUMINUM DOORS AND FRAMES

08 11 19 STAINLESS-STEEL DOORS AND FRAMES

08 11 73 SLIDING METAL FIRE DOORS

08 12 13 HOLLOW METAL FRAMES

08 13 16.13 ALUMINUM TERRACE DOORS

CADGS - Technical Specifications

CA-TS-01 6

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

08 14 16 FLUSH WOOD DOORS

08 14 33 STILE AND RAIL WOOD DOORS

08 14 33.13 WOOD TERRACE DOORS

08 16 74 SLIDING COMPOSITE-FRAMED GLASS DOORS

08 17 13 INTEGRATED METAL DOOR OPENING

ASSEMBLIES

08 18 16.13 SLIDING ALUMINUM-FRAMED GLASS DOORS

08 18 16.16 MULTIPANEL SLIDING ALUMINUM-FRAMED

GLASS DOORS

08 18 16.19 SLIDING WOOD-FRAMED GLASS DOORS

08 18 16.23 MULTIPANEL SLIDING WOOD-FRAMED GLASS

DOORS

08 31 13 ACCESS DOORS AND FRAMES

08 31 13.53 SECURITY ACCESS DOORS AND FRAMES

08 31 23 FLOOR DOORS

08 33 13 COILING COUNTER DOORS

08 33 23 OVERHEAD COILING DOORS

08 33 26 OVERHEAD COILING GRILLES

08 33 43 OVERHEAD COILING SMOKE CURTAINS

08 33 44 OVERHEAD COILING FIRE CURTAINS

08 34 53.13 SECURITY HOLLOW METAL DOORS AND

FRAMES

08 34 59 VAULT DOORS AND DAY GATES

08 34 73.13 METAL SOUND CONTROL DOOR ASSEMBLIES

08 34 73.16 WOOD SOUND CONTROL DOOR ASSEMBLIES

08 35 13 FOLDING DOORS

08 35 13.13 MULTIPANEL FOLDING ALUMINUM-FRAMED

GLASS DOORS

08 35 19.13 MULTIPANEL FOLDING WOOD-FRAMED GLASS

DOORS

08 36 13 SECTIONAL DOORS

08 38 00 TRAFFIC DOORS

08 41 13 ALUMINUM-FRAMED ENTRANCES AND

STOREFRONTS

08 41 26 ALL-GLASS ENTRANCES AND STOREFRONTS

08 41 26.23 INTERIOR ALL-GLASS ENTRANCES

08 42 13 ALUMINUM-FRAMED ENTRANCES

08 42 26 ALL-GLASS ENTRANCES

08 42 29.13 FOLDING AUTOMATIC ENTRANCES

08 42 29.23 SLIDING AUTOMATIC ENTRANCES

08 42 29.33 SWINGING AUTOMATIC ENTRANCES

08 42 33 REVOLVING DOOR ENTRANCES

08 42 43 INTENSIVE CARE UNIT/CRITICAL CARE UNIT

(ICU/CCU) ENTRANCES

08 43 13 ALUMINUM-FRAMED STOREFRONTS

08 44 13 GLAZED ALUMINUM CURTAIN WALLS

08 44 23 STRUCTURAL-SEALANT-GLAZED CURTAIN

WALLS

CADGS - Technical Specifications

CA-TS-01 7

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

08 44 33 SLOPED GLAZING ASSEMBLIES

08 45 13 STRUCTURED-POLYCARBONATE-PANEL

ASSEMBLIES

08 45 23 FIBERGLASS-SANDWICH-PANEL ASSEMBLIES

08 51 13 ALUMINUM WINDOWS

08 51 19 STAINLESS STEEL WINDOWS

08 51 23.13 HOT-ROLLED STEEL WINDOWS

08 51 23.23 COLD-ROLLED STEEL WINDOWS

08 52 00 WOOD WINDOWS

08 53 13 VINYL WINDOWS

08 54 13 FIBERGLASS WINDOWS

08 54 50 COMPOSITE WINDOWS

08 56 53 SECURITY WINDOWS

08 61 00 ROOF WINDOWS

08 62 00 UNIT SKYLIGHTS

08 63 00 METAL-FRAMED SKYLIGHTS

08 71 00 DOOR HARDWARE

08 71 11 DOOR HARDWARE (DESCRIPTIVE

SPECIFICATION)

08 71 13 POWER DOOR OPERATORS

08 78 13 ALL-GLASS-ENTRANCE HARDWARE

08 80 00 GLAZING

08 81 13 DECORATIVE GLASS GLAZING

08 83 00 MIRRORS

08 84 00 PLASTIC GLAZING

08 88 13 FIRE-RATED GLAZING

08 88 53 SECURITY GLAZING

08 91 16 OPERABLE WALL LOUVERS

08 91 19 FIXED LOUVERS

08 95 16 WALL VENTS

DIVISION 09 - FINISHES

09 01 90.52 MAINTENANCE REPAINTING

09 03 20 HISTORIC TREATMENT OF PLASTER

09 03 53 HISTORIC TREATMENT OF METAL CEILINGS

09 03 91 HISTORIC TREATMENT OF PLAIN PAINTING

09 03 94 HISTORIC TREATMENT OF DECORATIVE

PAINTING

09 03 95 HISTORIC TREATMENT OF ARTISTIC PAINTING

09 03 98 HISTORIC TREATMENT OF GILDING

09 05 61.13 MOISTURE VAPOR EMISSION CONTROL

09 21 16.23 GYPSUM BOARD SHAFT WALL ASSEMBLIES

09 22 16 NON-STRUCTURAL METAL FRAMING

09 23 00 GYPSUM PLASTERING

09 24 00 CEMENT PLASTERING

09 25 23 LIME-BASED PLASTERING

09 26 13 GYPSUM VENEER PLASTERING

09 27 13 GLASS-FIBER-REINFORCED GYPSUM

CADGS - Technical Specifications

CA-TS-01 8

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

FABRICATIONS

09 29 00 GYPSUM BOARD

09 29 01 PPL FAMILY 001

09 30 13 CERAMIC TILING

09 30 23 GLASS TILING

09 30 33 STONE TILING

09 51 13 ACOUSTICAL PANEL CEILINGS

09 51 23 ACOUSTICAL TILE CEILINGS

09 51 33 ACOUSTICAL METAL PAN CEILINGS

09 54 23 LINEAR METAL CEILINGS

09 54 26 SUSPENDED WOOD CEILINGS

09 54 36 SUSPENDED DECORATIVE GRIDS

09 54 43 STRETCHED-FABRIC CEILING SYSTEMS

09 54 46 FABRIC-WRAPPED CEILING PANELS

09 57 53 SECURITY CEILING ASSEMBLIES

09 62 29 CORK FLOORING

09 63 13 BRICK FLOORING

09 63 13.35 CHEMICAL-RESISTANT BRICK FLOORING

09 63 40 STONE FLOORING

09 64 00 WOOD FLOORING

09 64 36 BAMBOO FLOORING

09 64 66 WOOD ATHLETIC FLOORING

09 65 13 RESILIENT BASE AND ACCESSORIES

09 65 16 RESILIENT SHEET FLOORING

09 65 19 RESILIENT TILE AND PLANK FLOORING

09 65 36 STATIC-CONTROL RESILIENT FLOORING

09 65 43 LINOLEUM FLOORING

09 65 66 RESILIENT ATHLETIC FLOORING

09 66 13 PORTLAND CEMENT TERRAZZO FLOORING

09 66 23 RESINOUS MATRIX TERRAZZO FLOORING

09 67 23 RESINOUS FLOORING

09 67 66 FLUID-APPLIED ATHLETIC FLOORING

09 68 13 TILE CARPETING

09 68 16 SHEET CARPETING

09 69 00 ACCESS FLOORING

09 69 33 LOW-PROFILE FIXED HEIGHT ACCESS

FLOORING

09 72 00 WALL COVERINGS

09 75 13 STONE WALL FACING

09 75 19 STONE TRIM

09 77 13 STRETCHED-FABRIC WALL SYSTEMS

09 77 23 FABRIC-WRAPPED PANELS

09 84 33 SOUND-ABSORBING WALL UNITS

09 84 36 SOUND-ABSORBING CEILING UNITS

09 91 13 EXTERIOR PAINTING

09 91 14 EXTERIOR PAINTING (MPI STANDARDS)

09 91 23 INTERIOR PAINTING

09 91 24 INTERIOR PAINTING (MPI STANDARDS)

CADGS - Technical Specifications

CA-TS-01 9

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

09 93 00 STAINING AND TRANSPARENT FINISHING

09 93 01 STAINING AND TRANSPARENT FINISHING (MPI

STANDARDS)

09 94 19 MULTICOLOR INTERIOR FINISHING

09 94 23 GILDING

09 96 00 HIGH-PERFORMANCE COATINGS

09 96 01 HIGH-PERFORMANCE COATINGS (MPI

STANDARDS)

09 96 33 HIGH-TEMPERATURE-RESISTANT COATINGS

09 96 46 INTUMESCENT PAINTING

09 96 47 INTUMESCENT PAINTING (MPI STANDARDS)

09 96 53 ELASTOMERIC COATINGS

09 96 54 ELASTOMERIC COATINGS (MPI STANDARDS)

09 97 26 CEMENTITIOUS COATINGS

DIVISION 10 - SPECIALTIES

10 11 00 VISUAL DISPLAY UNITS

10 11 46 VISUAL DISPLAY FABRICS

10 12 00 DISPLAY CASES

10 13 00 DIRECTORIES

10 14 16 PLAQUES

10 14 19 DIMENSIONAL LETTER SIGNAGE

10 14 23 PANEL SIGNAGE

10 14 23.16 ROOM-IDENTIFICATION PANEL SIGNAGE

10 14 26 POST AND PANEL/PYLON SIGNAGE

10 14 29 MODULAR SIGNAGE

10 14 73 PAINTED SIGNAGE

10 21 13.13 METAL TOILET COMPARTMENTS

10 21 13.14 STAINLESS STEEL TOILET COMPARTMENTS

10 21 13.16 PLASTIC-LAMINATE-CLAD TOILET

COMPARTMENTS

10 21 13.17 PHENOLIC-CORE TOILET COMPARTMENTS

10 21 13.19 PLASTIC TOILET COMPARTMENTS

10 21 13.40 STONE TOILET COMPARTMENTS

10 21 13.43 PHENOLIC-CORE PEDESTAL-MOUNTED

PRIVACY TOILET COMPARTMENTS

10 21 16.13 METAL SHOWER AND DRESSING

COMPARTMENTS

10 21 16.14 STAINLESS-STEEL SHOWER AND DRESSING

COMPARTMENTS

10 21 16.17 PHENOLIC-CORE SHOWER AND DRESSING

COMPARTMENTS

10 21 16.19 PLASTIC SHOWER AND DRESSING

COMPARTMENTS

10 21 23 CUBICLE CURTAINS AND TRACK

10 22 13 WIRE MESH PARTITIONS

10 22 19 DEMOUNTABLE PARTITIONS

10 22 33 ACCORDION FOLDING PARTITIONS

CADGS - Technical Specifications

CA-TS-01 10

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

10 22 39 FOLDING PANEL PARTITIONS

10 22 39.13 FOLDING GLASS-PANEL PARTITIONS

10 22 46 ALL-GLASS PARTITIONS

10 26 00 WALL AND DOOR PROTECTION

10 28 00 TOILET, BATH, AND LAUNDRY ACCESSORIES

10 28 13.63 DETENTION TOILET ACCESSORIES

10 28 19 TUB AND SHOWER ENCLOSURES

10 43 00 EMERGENCY AID SPECIALTIES

10 44 13 FIRE PROTECTION CABINETS

10 44 16 FIRE EXTINGUISHERS

10 45 13 PHOTOLUMINESCENT EGRESS PATH

MARKINGS

10 51 13 METAL LOCKERS

10 51 13.13 COIN-OPERATED METAL LOCKERS

10 51 16 WOOD LOCKERS

10 51 23 PLASTIC-LAMINATE-CLAD LOCKERS

10 51 29 PHENOLIC LOCKERS

10 51 43 WIRE MESH STORAGE LOCKERS

10 55 00.13 USPS-DELIVERY POSTAL SPECIALTIES

10 55 00.16 PRIVATE-DELIVERY POSTAL SPECIALTIES

10 56 13 METAL STORAGE SHELVING

10 56 26 MOBILE STORAGE SHELVING

10 73 13 AWNINGS

10 73 43 TRANSPORTATION STOP SHELTERS

10 75 16 GROUND-SET FLAGPOLES

10 75 23 WALL-MOUNTED FLAGPOLES

10 75 26 ROOF-MOUNTED FLAGPOLES

10 75 29 PLAZA-MOUNTED FLAGPOLES

10 83 16 BANNERS

DIVISION 11 - EQUIPMENT

11 11 36 VEHICLE CHARGING EQUIPMENT

11 12 00 PARKING CONTROL EQUIPMENT

11 13 13 LOADING DOCK BUMPERS

11 13 16 LOADING DOCK SEALS AND SHELTERS

11 13 19 STATIONARY LOADING DOCK EQUIPMENT

11 13 23 PORTABLE DOCK EQUIPMENT

11 19 16 DETENTION GUN LOCKERS

11 30 13 RESIDENTIAL APPLIANCES

11 40 00 FOODSERVICE EQUIPMENT

11 51 23 LIBRARY STACK SYSTEMS

11 52 13 PROJECTION SCREENS

11 52 13.19 REAR PROJECTION SCREENS

11 53 13 LABORATORY FUME HOODS

11 61 23 FOLDING AND PORTABLE STAGES

11 61 43 STAGE CURTAINS

11 66 23 GYMNASIUM EQUIPMENT

11 66 53 GYMNASIUM DIVIDERS

CADGS - Technical Specifications

CA-TS-01 11

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

11 68 00 PLAY FIELD EQUIPMENT AND STRUCTURES

11 73 00 PATIENT CARE EQUIPMENT

11 82 26 FACILITY WASTE COMPACTORS

11 98 12 DETENTION DOORS AND FRAMES

11 98 14 DETENTION DOOR HARDWARE

11 98 21 DETENTION WINDOWS

DIVISION 12 - FURNISHINGS

12 21 13 HORIZONTAL LOUVER BLINDS

12 21 16 VERTICAL LOUVER BLINDS

12 22 00 CURTAINS AND DRAPES

12 24 13 ROLLER WINDOW SHADES

12 24 16 PLEATED WINDOW SHADES

12 32 13 MANUFACTURED WOOD-VENEER-FACED

CASEWORK

12 32 16 MANUFACTURED PLASTIC-LAMINATE-CLAD

CASEWORK

12 35 30 RESIDENTIAL CASEWORK

12 35 53.13 METAL LABORATORY CASEWORK

12 35 53.16 PLASTIC-LAMINATE-CLAD LABORATORY

CASEWORK

12 35 53.19 WOOD LABORATORY CASEWORK

12 35 70 HEALTHCARE CASEWORK

12 36 16 METAL COUNTERTOPS

12 36 19 WOOD COUNTERTOPS

12 36 23.13 PLASTIC-LAMINATE-CLAD COUNTERTOPS

12 36 40 STONE COUNTERTOPS

12 36 61 SIMULATED STONE COUNTERTOPS

12 48 13 ENTRANCE FLOOR MATS AND FRAMES

12 48 16 ENTRANCE FLOOR GRILLES

12 55 00 DETENTION FURNITURE

12 61 00 FIXED AUDIENCE SEATING

12 63 13 STADIUM AND ARENA BENCH SEATING

12 66 00 TELESCOPING STANDS

12 92 00 INTERIOR PLANTERS AND ARTIFICIAL PLANTS

DIVISION 13 - SPECIAL CONSTRUCTION

13 27 00 VAULTS

13 34 19 METAL BUILDING SYSTEMS

13 34 23.16 FABRICATED CONTROL BOOTHS

13 47 13 CATHODIC PROTECTION

13 49 00 RADIATION PROTECTION

DIVISION 14 - CONVEYING EQUIPMENT

14 21 00 ELECTRIC TRACTION ELEVATORS

14 24 00 HYDRAULIC ELEVATORS

14 24 13 HYDRAULIC FREIGHT ELEVATORS

14 26 00 LIMITED-USE/LIMITED-APPLICATION

CADGS - Technical Specifications

CA-TS-01 12

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

ELEVATORS

14 42 00 WHEELCHAIR LIFTS

14 91 82 TRASH CHUTES

FACILITY SERVICES SUBGROUP

DIVISION 21 - FIRE SUPPRESSION

21 05 00 COMMON WORK RESULTS FOR FIRE

SUPPRESSION

21 05 23 GENERAL-DUTY VALVES FOR WATER-BASED

FIRE-SUPPRESSION PIPING

21 05 29 HANGERS AND SUPPORTS FOR FIRE-

SUPPRESSION PIPING AND EQUIPMENT

21 05 33 HEAT TRACING FOR FIRE-SUPPRESSION

PIPING

21 05 48 VIBRATION AND SEISMIC CONTROLS FOR

FIRE-SUPPRESSION PIPING AND EQUIPMENT

21 05 48.13 VIBRATION CONTROLS FOR FIRE-

SUPPRESSION PIPING AND EQUIPMENT

21 05 53 IDENTIFICATION FOR FIRE-SUPPRESSION

PIPING AND EQUIPMENT

21 07 00 FIRE-SUPPRESSION SYSTEMS INSULATION

21 08 00 COMMISSIONING OF FIRE SUPPRESSION

21 10 00 WATER-BASED FIRE-SUPPRESSION SYSTEMS

21 13 39 FOAM-WATER SYSTEMS

21 21 13.13 HIGH-PRESSURE, CARBON-DIOXIDE FIRE-

EXTINGUISHING SYSTEMS

21 21 13.16 LOW-PRESSURE, CARBON-DIOXIDE FIRE-

EXTINGUISHING SYSTEMS

21 22 00 CLEAN-AGENT FIRE-EXTINGUISHING

SYSTEMS

21 31 13 ELECTRIC-DRIVE, CENTRIFUGAL FIRE PUMPS

21 31 16 DIESEL-DRIVE, CENTRIFUGAL FIRE PUMPS

21 32 13 ELECTRIC-DRIVE, VERTICAL-TURBINE FIRE

PUMPS

21 32 16 DIESEL-DRIVE, VERTICAL-TURBINE FIRE

PUMPS

21 34 13 PRESSURE-MAINTENANCE PUMPS

DIVISION 22 - PLUMBING

22 05 00 COMMON WORK RESULTS FOR PLUMBING

22 05 23 GENERAL-DUTY VALVES FOR PLUMBING

PIPING

22 05 29 HANGERS AND SUPPORTS FOR PLUMBING

PIPING AND EQUIPMENT

22 05 33 HEAT TRACING FOR PLUMBING PIPING

22 05 48 VIBRATION AND SEISMIC CONTROLS FOR

PLUMBING PIPING AND EQUIPMENT

22 05 48.13 VIBRATION CONTROLS FOR PLUMBING PIPING

AND EQUIPMENT

CADGS - Technical Specifications

CA-TS-01 13

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

22 05 53 IDENTIFICATION FOR PLUMBING PIPING AND

EQUIPMENT

22 05 93 TESTING, ADJUSTING, AND BALANCING FOR

PLUMBING

22 07 16 PLUMBING EQUIPMENT INSULATION

22 07 19 PLUMBING PIPING INSULATION

22 08 00 COMMISSIONING OF PLUMBING

22 09 63 MEDICAL GAS ALARMS

22 11 16 DOMESTIC WATER PIPING

22 11 17 GRAY-WATER PIPING

22 11 19 DOMESTIC WATER PIPING SPECIALTIES

22 11 23.13 DOMESTIC-WATER PACKAGED BOOSTER

PUMPS

22 11 23.21 INLINE, DOMESTIC-WATER PUMPS

22 12 16 FACILITY ELEVATED, POTABLE-WATER

STORAGE TANKS

22 12 19 FACILITY GROUND-MOUNTED, POTABLE-

WATER STORAGE TANKS

22 12 23.11 FACILITY INDOOR POTABLE-WATER STORAGE

TANKS

22 13 16 SANITARY WASTE AND VENT PIPING

22 13 19 SANITARY WASTE PIPING SPECIALTIES

22 13 19.13 SANITARY DRAINS

22 13 23 SANITARY WASTE INTERCEPTORS

22 13 29 SANITARY SEWERAGE PUMPS

22 13 43 FACILITY PACKAGED SEWAGE PUMPING

STATIONS

22 13 53 FACILITY SEPTIC TANKS

22 13 63 FACILITY GRAY-WATER STORAGE TANKS

22 14 14 STORM DRAINAGE PIPING

22 14 23 STORM DRAINAGE PIPING SPECIALTIES

22 14 29 SUMP PUMPS

22 14 63 FACILITY STORM-WATER RETENTION TANKS

22 15 13 GENERAL-SERVICE COMPRESSED-AIR PIPING

22 15 19 GENERAL-SERVICE PACKAGED AIR

COMPRESSORS AND RECEIVERS

22 25 00 PLUMBING SYSTEMS WATER TREATMENT

22 31 00 DOMESTIC WATER SOFTENERS

22 32 00 DOMESTIC WATER FILTRATION EQUIPMENT

22 33 00 ELECTRIC, DOMESTIC-WATER HEATERS

22 34 00 FUEL-FIRED, DOMESTIC-WATER HEATERS

22 35 00 DOMESTIC-WATER HEAT EXCHANGERS

22 41 00 RESIDENTIAL PLUMBING FIXTURES

22 42 00 COMMERCIAL PLUMBING FIXTURES

22 43 00 HEALTHCARE PLUMBING FIXTURES

22 45 00 EMERGENCY PLUMBING FIXTURES

22 46 00 SECURITY PLUMBING FIXTURES

22 47 00 DRINKING FOUNTAINS AND WATER COOLERS

CADGS - Technical Specifications

CA-TS-01 14

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

22 61 13 COMPRESSED-AIR PIPING FOR LABORATORY

AND HEALTHCARE FACILITIES

22 61 19 COMPRESSED-AIR EQUIPMENT FOR

LABORATORY AND HEALTHCARE FACILITIES

22 62 13 VACUUM PIPING FOR LABORATORY AND

HEALTHCARE FACILITIES

22 62 19 VACUUM EQUIPMENT FOR LABORATORY AND

HEALTHCARE FACILITIES

22 63 13 GAS PIPING FOR LABORATORY AND

HEALTHCARE FACILITIES

22 66 00 CHEMICAL-WASTE SYSTEMS FOR

LABORATORY AND HEALTHCARE FACILITIES

22 67 13 PROCESSED WATER PIPING FOR

LABORATORY AND HEALTHCARE FACILITIES

22 67 19 PROCESSED WATER EQUIPMENT FOR

LABORATORY AND HEALTHCARE FACILITIES

DIVISION 23 - HEATING, VENTILATING, AND AIR CONDITIONING (HVAC)

23 01 30.52 EXISTING HVAC AIR DISTRIBUTION SYSTEM

CLEANING

23 05 00 COMMON WORK RESULTS FOR HVAC

23 05 23 GENERAL-DUTY VALVES FOR HVAC PIPING

23 05 29 HANGERS AND SUPPORTS FOR HVAC PIPING

AND EQUIPMENT

23 05 33 HEAT TRACING FOR HVAC PIPING

23 05 46 COATINGS FOR HVAC

23 05 48 VIBRATION AND SEISMIC CONTROLS FOR

HVAC

23 05 48.13 VIBRATION CONTROLS FOR HVAC

23 05 53 IDENTIFICATION FOR HVAC PIPING AND

EQUIPMENT

23 05 66 ANTIMICROBIAL ULTRAVIOLET LAMP

SYSTEMS FOR HVAC

23 05 93 TESTING, ADJUSTING, AND BALANCING FOR

HVAC

23 07 13 DUCT INSULATION

23 07 16 HVAC EQUIPMENT INSULATION

23 07 19 HVAC PIPING INSULATION

23 08 00 COMMISSIONING OF HVAC

23 09 23 DIRECT DIGITAL CONTROL (DDC) SYSTEM

FOR HVAC

23 09 23.11 CONTROL VALVES

23 09 23.12 CONTROL DAMPERS

23 09 23.13 ENERGY METERS

23 09 23.14 FLOW INSTRUMENTS

23 09 23.16 GAS INSTRUMENTS

23 09 23.17 LEVEL INSTRUMENTS

23 09 23.18 LEAK DETECTION INSTRUMENTS

23 09 23.19 MOISTURE INSTRUMENTS

CADGS - Technical Specifications

CA-TS-01 15

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

23 09 23.21 MOTION INSTRUMENTS

23 09 23.22 POSITION INSTRUMENTS

23 09 23.23 PRESSURE INSTRUMENTS

23 09 23.24 SPEED INSTRUMENTS

23 09 23.27 TEMPERATURE INSTRUMENTS

23 09 23.33 VIBRATION INSTRUMENTS

23 09 23.43 WEATHER STATIONS

23 09 93.11 SEQUENCE OF OPERATIONS FOR HVAC DDC

23 11 13 FACILITY FUEL-OIL PIPING

23 11 23 FACILITY NATURAL-GAS PIPING

23 11 26 FACILITY LIQUEFIED-PETROLEUM GAS PIPING

23 12 13 FACILITY FUEL-OIL PUMPS

23 13 13 FACILITY UNDERGROUND FUEL-OIL STORAGE

TANKS

23 13 23 FACILITY ABOVEGROUND FUEL-OIL STORAGE

TANKS

23 21 13 HYDRONIC PIPING

23 21 13.13 UNDERGROUND HYDRONIC PIPING

23 21 13.33 GROUND-LOOP HEAT-PUMP PIPING

23 21 16 HYDRONIC PIPING SPECIALTIES

23 21 23 HYDRONIC PUMPS

23 22 13 STEAM AND CONDENSATE PIPING

23 22 13.13 UNDERGROUND STEAM AND CONDENSATE

HEATING PIPING

23 22 16 STEAM AND CONDENSATE HEATING PIPING

SPECIALTIES

23 22 23 STEAM CONDENSATE PUMPS

23 23 00 REFRIGERANT PIPING

23 25 00 HVAC WATER TREATMENT

23 25 13 WATER TREATMENT FOR CLOSED-LOOP

HYDRONIC SYSTEMS

23 25 16 WATER TREATMENT FOR OPEN-LOOP

HYDRONIC SYSTEMS

23 25 19 WATER TREATMENT FOR STEAM SYSTEM

FEEDWATER

23 25 23 WATER TREATMENT FOR HUMIDIFICATION

STEAM SYSTEM FEEDWATER

23 25 33 HVAC MAKEUP-WATER FILTRATION

EQUIPMENT

23 31 13 METAL DUCTS

23 31 16 NONMETAL DUCTS

23 31 19.13 SHOP-FABRICATED HVAC CASINGS

23 31 19.16 MANUFACTURED HVAC CASINGS

23 33 00 AIR DUCT ACCESSORIES

23 34 00 HVAC FANS

23 34 33.13 COMMERCIAL AIR CURTAINS

23 34 33.16 INDUSTRIAL AIR CURTAINS

23 34 39 HIGH-VOLUME, LOW-SPEED FANS

CADGS - Technical Specifications

CA-TS-01 16

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

23 35 33 LISTED KITCHEN VENTILATION SYSTEM

EXHAUST DUCTS

23 36 00 AIR TERMINAL UNITS

23 37 13.13 AIR DIFFUSERS

23 37 13.23 REGISTERS AND GRILLES

23 37 13.43 SECURITY REGISTERS AND GRILLES

23 37 16 FABRIC AIR-DISTRIBUTION DEVICES

23 37 23 HVAC GRAVITY VENTILATORS

23 38 13 COMMERCIAL-KITCHEN HOODS

23 41 00 PARTICULATE AIR FILTRATION

23 41 33 HIGH-EFFICIENCY PARTICULATE AIR

FILTRATION

23 42 00 GAS-PHASE AIR FILTRATION

23 43 00 ELECTRONIC AIR CLEANERS

23 51 13.11 DRAFT CONTROL FANS

23 51 13.16 VENT DAMPERS

23 51 16 FABRICATED BREECHINGS AND

ACCESSORIES

23 51 23 GAS VENTS

23 51 33 INSULATED SECTIONAL CHIMNEYS

23 52 13 ELECTRIC BOILERS

23 52 16 CONDENSING BOILERS

23 52 23 CAST-IRON BOILERS

23 52 33 WATER-TUBE BOILERS

23 52 39 FIRE-TUBE BOILERS

23 53 13 BOILER FEEDWATER PUMPS

23 53 16 DEAERATORS

23 54 13 ELECTRIC-RESISTANCE FURNACES

23 54 16.13 GAS-FIRED FURNACES

23 54 16.16 OIL-FIRED FURNACES

23 55 13.16 GAS-FIRED DUCT HEATERS

23 55 23.13 LOW-INTENSITY, GAS-FIRED, RADIANT

HEATERS

23 55 23.16 HIGH-INTENSITY, GAS-FIRED, RADIANT

HEATERS

23 55 33.13 OIL-FIRED UNIT HEATERS

23 55 33.16 GAS-FIRED UNIT HEATERS

23 56 13.13 HEATING, FLAT-PLATE, SOLAR COLLECTORS

23 56 13.19 HEATING, SOLAR, VACUUM-TUBE

COLLECTORS

23 57 00 HEAT EXCHANGERS FOR HVAC

23 62 00 PACKAGED COMPRESSOR AND CONDENSER

UNITS

23 63 13 AIR-COOLED REFRIGERANT CONDENSERS

23 63 33 EVAPORATIVE REFRIGERANT CONDENSERS

23 64 13.13 DIRECT-FIRED ABSORPTION WATER

CHILLERS

23 64 13.16 INDIRECT-FIRED ABSORPTION WATER

CADGS - Technical Specifications

CA-TS-01 17

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

CHILLERS

23 64 16 CENTRIFUGAL WATER CHILLERS

23 64 23.13 AIR-COOLED, SCROLL WATER CHILLERS

23 64 23.16 WATER-COOLED, SCROLL WATER CHILLERS

23 64 26.13 AIR-COOLED, ROTARY-SCREW WATER

CHILLERS

23 64 26.16 WATER-COOLED, ROTARY-SCREW WATER

CHILLERS

23 65 13.13 OPEN-CIRCUIT, FORCED-DRAFT COOLING

TOWERS

23 65 13.16 CLOSED-CIRCUIT, FORCED-DRAFT COOLING

TOWERS

23 65 14.13 OPEN-CIRCUIT, INDUCED-DRAFT,

COUNTERFLOW COOLING TOWERS

23 65 14.14 OPEN-CIRCUIT, INDUCED-DRAFT,

CROSSFLOW COOLING TOWERS

23 65 14.16 CLOSED-CIRCUIT, INDUCED-DRAFT,

COUNTERFLOW COOLING TOWERS

23 65 14.17 CLOSED-CIRCUIT, INDUCED-DRAFT,

COMBINED-FLOW COOLING TOWERS

23 72 13 HEAT WHEEL AIR-TO-AIR ENERGY RECOVERY

UNITS

23 72 16 HEAT PIPE AIR-TO-AIR ENERGY RECOVERY

UNITS

23 72 19 FIXED PLATE AIR-TO-AIR ENERGY RECOVERY

UNITS

23 72 23.13 PACKAGED INDOOR HEAT WHEEL ENERGY

RECOVERY UNITS

23 72 23.19 PACKAGED INDOOR FIXED PLATE ENERGY

RECOVERY UNITS

23 72 23.23 PACKAGED, OUTDOOR, HEAT WHEEL ENERGY

RECOVERY UNITS

23 72 23.29 PACKAGED, OUTDOOR, FIXED PLATE ENERGY

RECOVERY UNITS

23 73 13.13 INDOOR, BASIC AIR-HANDLING UNITS

23 73 13.16 INDOOR, SEMI-CUSTOM AIR-HANDLING UNITS

23 73 13.19 INDOOR, CUSTOM AIR-HANDLING UNITS

23 73 33.16 INDOOR, INDIRECT, GAS-FIRED HEATING AND

VENTILATING UNITS

23 73 39 INDOOR, DIRECT-FIRED HEATING AND

VENTILATING UNITS

23 73 43.16 OUTDOOR, SEMI-CUSTOM AIR-HANDLING

UNITS

23 73 43.19 OUTDOOR, CUSTOM AIR-HANDLING UNITS

23 74 16.11 PACKAGED, SMALL-CAPACITY, ROOFTOP AIR-

CONDITIONING UNITS

23 74 16.13 PACKAGED, LARGE-CAPACITY, ROOFTOP AIR-

CONDITIONING UNITS

23 74 23.13 PACKAGED, DIRECT-FIRED, OUTDOOR,

CADGS - Technical Specifications

CA-TS-01 18

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

HEATING-ONLY MAKEUP-AIR UNITS

23 74 23.16 PACKAGED, INDIRECT-FIRED, OUTDOOR,

HEATING-ONLY MAKEUP-AIR UNITS

23 74 33 DEDICATED OUTDOOR-AIR UNITS

23 81 13.11 PACKAGED TERMINAL AIR-CONDITIONERS,

THROUGH-WALL UNITS

23 81 13.12 PACKAGED TERMINAL AIR-CONDITIONERS,

FREESTANDING UNITS

23 81 13.13 PACKAGED TERMINAL AIR-CONDITIONERS,

OUTDOOR, WALL-MOUNTED UNITS

23 81 19 SELF-CONTAINED AIR-CONDITIONERS

23 81 23.11 SMALLCAPACITY(6TONS(21 KW) AND

SMALLER), COMPUTER-ROOM AIR-

CONDITIONERS, FLOOR-MOUNTED UNITS

23 81 23.12 LARGECAPACITY(7TONS(25 KW) AND

LARGER), COMPUTER-ROOM AIR-

CONDITIONERS, FLOOR-MOUNTED UNITS

23 81 23.13 COMPUTER-ROOM AIR-CONDITIONERS,

CEILING-MOUNTED UNITS

23 81 23.14 COMPUTER-ROOM AIR-CONDITIONERS,

CONSOLE UNITS

23 81 23.18 COMPUTER-ROOM, RACK-COOLING

EQUIPMENT

23 81 26 SPLIT-SYSTEM AIR-CONDITIONERS

23 81 29 VARIABLE-REFRIGERANT-FLOW HVAC

SYSTEMS

23 81 46 WATER-SOURCE UNITARY HEAT PUMPS

23 81 46.13 WATER-TO-AIR HEAT PUMPS

23 82 13 VALANCE HEATING AND COOLING UNITS

23 82 14 CHILLED BEAMS

23 82 16.11 HYDRONIC AIR COILS

23 82 16.12 STEAM AIR COILS

23 82 16.13 REFRIGERANT AIR COILS

23 82 16.14 ELECTRIC-RESISTANCE AIR COILS

23 82 19 FAN COIL UNITS

23 82 23 UNIT VENTILATORS

23 82 29 RADIATORS

23 82 33 CONVECTORS

23 82 36 FINNED-TUBE RADIATION HEATERS

23 82 39.13 CABINET UNIT HEATERS

23 82 39.16 PROPELLER UNIT HEATERS

23 82 39.19 WALL AND CEILING UNIT HEATERS

23 83 13 RADIANT-HEATING ELECTRIC CABLES

23 83 16 RADIANT-HEATING HYDRONIC PIPING

23 83 23 RADIANT-HEATING ELECTRIC PANELS

23 84 13.16 WETTED-ELEMENT HUMIDIFIERS

23 84 13.19 ATOMIZING HUMIDIFIERS

23 84 13.23 DIRECT-STEAM-INJECTION HUMIDIFIERS

CADGS - Technical Specifications

CA-TS-01 19

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

23 84 13.29 SELF-CONTAINED STEAM HUMIDIFIERS

23 84 13.36 HEAT EXCHANGER HUMIDIFIERS

23 84 16.13 OUTDOOR, MECHANICAL DEHUMIDIFICATION

UNITS

23 84 16.16 INDOOR, MECHANICAL DEHUMIDIFICATION

UNITS

DIVISION 26 - ELECTRICAL

26 00 10 SUPPLEMENTAL REQUIREMENTS FOR

ELECTRICAL

26 05 13 MEDIUM-VOLTAGE CABLES

26 05 19 LOW-VOLTAGE ELECTRICAL POWER

CONDUCTORS AND CABLES

26 05 23 CONTROL-VOLTAGE ELECTRICAL POWER

CABLES

26 05 26 GROUNDING AND BONDING FOR ELECTRICAL

SYSTEMS

26 05 29 HANGERS AND SUPPORTS FOR ELECTRICAL

SYSTEMS

26 05 33.13 CONDUITS FOR ELECTRICAL SYSTEMS

26 05 33.16 BOXES AND COVERS FOR ELECTRICAL

SYSTEMS

26 05 33.23 SURFACE RACEWAYS FOR ELECTRICAL

SYSTEMS

26 05 36 CABLE TRAYS FOR ELECTRICAL SYSTEMS

26 05 39 UNDERFLOOR RACEWAYS FOR ELECTRICAL

SYSTEMS

26 05 43 UNDERGROUND DUCTS AND RACEWAYS FOR

ELECTRICAL SYSTEMS

26 05 44 SLEEVES AND SLEEVE SEALS FOR

ELECTRICAL RACEWAYS AND CABLING

26 05 48 VIBRATION AND SEISMIC CONTROLS FOR

ELECTRICAL SYSTEMS

26 05 53 IDENTIFICATION FOR ELECTRICAL SYSTEMS

26 05 73 POWER SYSTEM STUDIES

26 08 00 COMMISSIONING OF ELECTRICAL SYSTEMS

26 09 13 ELECTRICAL POWER MONITORING

26 09 23 LIGHTING CONTROL DEVICES

26 09 36 MODULAR DIMMING CONTROLS

26 09 43.16 ADDRESSABLE LUMINAIRE LIGHTING

CONTROLS

26 09 43.23 RELAY-BASED LIGHTING CONTROLS

26 11 16.11 SECONDARY UNIT SUBSTATIONS WITH

SWITCHGEAR SECONDARY

26 11 16.12 SECONDARY UNIT SUBSTATIONS WITH

SWITCHBOARD SECONDARY

26 11 16.13 SECONDARY UNIT SUBSTATIONS WITH

MOTOR CONTROL CENTER SECONDARY

26 12 13 LIQUID-FILLED, MEDIUM-VOLTAGE

CADGS - Technical Specifications

CA-TS-01 20

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

TRANSFORMERS

26 12 16 DRY-TYPE, MEDIUM-VOLTAGE

TRANSFORMERS

26 12 19 PAD-MOUNTED, LIQUID-FILLED, MEDIUM-

VOLTAGE TRANSFORMERS

26 13 23 MEDIUM-VOLTAGE METAL-ENCLOSED

SWITCHGEAR

26 13 26 MEDIUM-VOLTAGE METAL-CLAD SWITCHGEAR

26 13 29 MEDIUM-VOLTAGE COMPARTMENTALIZED

SWITCHGEAR

26 22 13 LOW-VOLTAGE DISTRIBUTION

TRANSFORMERS

26 22 16 LOW-VOLTAGE BUCK-BOOST

TRANSFORMERS

26 23 00 LOW-VOLTAGE SWITCHGEAR

26 23 13 PARALLELING LOW-VOLTAGE SWITCHGEAR

26 24 13 SWITCHBOARDS

26 24 16 PANELBOARDS

26 24 16.16 ELECTRONICALLY OPERATED CIRCUIT-

BREAKER PANELBOARDS

26 24 19 MOTOR-CONTROL CENTERS

26 25 00 LOW-VOLTAGE ENCLOSED BUS ASSEMBLIES

26 27 13 ELECTRICITY METERING

26 27 16 ELECTRICAL CABINETS AND ENCLOSURES

26 27 19 MULTI-OUTLET ASSEMBLIES

26 27 26 WIRING DEVICES

26 27 26.11 GENERAL-USE SWITCHES, DIMMER

SWITCHES, AND FAN-SPEED CONTROLLER

SWITCHES

26 27 26.31 GENERAL-GRADE SINGLE STRAIGHT-BLADE

RECEPTACLES

26 27 26.33 GENERAL-GRADE DUPLEX STRAIGHT-BLADE

RECEPTACLES

26 27 26.35 HOSPITAL-GRADE STRAIGHT-BLADE

RECEPTACLES

26 27 26.37 RECEPTACLES WITH ARC-FAULT AND

GROUND-FAULT PROTECTIVE DEVICES

26 27 26.39 LOCKING RECEPTACLES

26 27 26.41 PIN-AND-SLEEVE RECEPTACLES

26 27 26.43 SPECIAL-PURPOSE POWER OUTLET

ASSEMBLIES

26 27 26.51 CONNECTORS, CORDS, AND PLUGS

26 27 33 POWER DISTRIBUTION UNITS

26 28 13 FUSES

26 28 16 ENCLOSED SWITCHES AND CIRCUIT

BREAKERS

26 29 13.03 MANUAL AND MAGNETIC MOTOR

CONTROLLERS

26 29 13.06 SOFT-START MOTOR CONTROLLERS

CADGS - Technical Specifications

CA-TS-01 21

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

26 29 23 VARIABLE-FREQUENCY MOTOR

CONTROLLERS

26 31 00 PHOTOVOLTAIC COLLECTORS

26 32 13.13 DIESEL-ENGINE-DRIVEN GENERATOR SETS

26 32 13.16 GAS-ENGINE-DRIVEN GENERATOR SETS

26 32 13.19 BI-FUEL-ENGINE-DRIVEN GENERATOR SETS

26 32 23.13 HORIZONTAL-AXIS WIND TURBINES

26 32 23.16 VERTICAL-AXIS WIND TURBINES

26 33 23 CENTRAL BATTERY EQUIPMENT

26 33 43 BATTERY CHARGERS

26 33 53 STATIC UNINTERRUPTIBLE POWER SUPPLY

26 35 33 POWER FACTOR CORRECTION EQUIPMENT

26 36 00 TRANSFER SWITCHES

26 41 13 LIGHTNING PROTECTION FOR STRUCTURES

26 43 13 SURGE PROTECTIVE DEVICES FOR LOW-

VOLTAGE ELECTRICAL POWER CIRCUITS

26 50 00 LIGHTING

26 55 61 THEATRICAL LIGHTING

26 55 68 ATHLETIC FIELD LIGHTING

DIVISION 27 - COMMUNICATIONS

27 05 28 PATHWAYS FOR COMMUNICATIONS SYSTEMS

27 11 00 COMMUNICATIONS EQUIPMENT ROOM

FITTINGS

27 13 13 COMMUNICATIONS COPPER BACKBONE

CABLING

27 13 23 COMMUNICATIONS OPTICAL FIBER

BACKBONE CABLING

27 13 33 COMMUNICATIONS COAXIAL BACKBONE

CABLING

27 15 13 COMMUNICATIONS COPPER HORIZONTAL

CABLING

27 15 23 COMMUNICATIONS OPTICAL FIBER

HORIZONTAL CABLING

27 15 33 COMMUNICATIONS COAXIAL HORIZONTAL

CABLING

27 16 11 COMMUNICATIONS HYBRID CABLING

27 41 33 MASTER ANTENNA TELEVISION SYSTEM

27 51 16 PUBLIC ADDRESS SYSTEMS

27 51 19 SOUND MASKING SYSTEMS

27 51 23.20 COMMERCIAL INTERCOMMUNICATIONS AND

PROGRAM SYSTEMS

27 51 23.50 EDUCATIONAL INTERCOMMUNICATIONS AND

PROGRAM SYSTEMS

27 52 23 NURSE CALL/CODE BLUE SYSTEMS

27 53 13 CLOCK SYSTEMS

DIVISION 28 - ELECTRONIC SAFETY AND SECURITY

CADGS - Technical Specifications

CA-TS-01 22

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

28 10 00 ACCESS CONTROL

28 13 00 ACCESS CONTROL SOFTWARE AND

DATABASE MANAGEMENT

28 14 00 ACCESS CONTROL SYSTEM HARDWARE

28 15 00 INTEGRATED ACCESS CONTROL HARDWARE

DEVICES

28 15 11 INTEGRATED CREDENTIAL READERS AND

ENTRY MANAGEMENT

28 15 13 ACCESS CONTROL CREDENTIALS

28 15 15 ELECTRIFIED LOCKING DEVICES AND

ACCESSORIES

28 15 17 EGRESS MANAGEMENT DEVICES

28 15 19 ACCESS CONTROL REMOTE DEVICES

28 15 21 TELEPHONE ENTRY SYSTEMS

28 15 23 INTERCOM ENTRY SYSTEMS

28 15 25 ELECTRONIC KEY MANAGEMENT SYSTEMS

28 15 27 ACCESS CONTROL ELECTRONIC TURNSTILES

AND MOBILITY SYSTEMS

28 20 00 VIDEO SURVEILLANCE

28 31 00 INTRUSION DETECTION

28 31 21 AREA AND PERIMETER INTRUSION

DETECTION

28 44 00 REFRIGERANT DETECTION AND ALARM

28 46 00 FIRE DETECTION AND ALARM

28 46 14 SINGLE- AND MULTIPLE-STATION ALARMS

28 47 00 MASS NOTIFICATION

28 48 13 EMERGENCY RESPONDER COMMUNICATIONS

ENHANCEMENT SYSTEM (ERCES)

28 48 16 TWO-WAY EMERGENCY COMMUNICATIONS

SYSTEMS FOR RESCUE ASSISTANCE

28 52 13 DETENTION MONITORING AND CONTROL

SYSTEM AND INTERFACES

DIVISION 31 - EARTHWORK

31 10 00 SITE CLEARING

31 20 00 EARTH MOVING

31 23 19 DEWATERING

31 50 00 EXCAVATION SUPPORT AND PROTECTION

31 62 13 CONCRETE PILES

31 62 16 STEEL PILES

31 62 19 TIMBER PILES

31 62 23 COMPOSITE PILES

31 63 16 AUGER CAST GROUT PILES

31 63 29 DRILLED CONCRETE PIERS AND SHAFTS

DIVISION 32 - EXTERIOR IMPROVEMENTS

32 12 16 ASPHALT PAVING

32 12 23 IMPRINTED ASPHALT

CADGS - Technical Specifications

CA-TS-01 23

Copyright © 2024 by the American Institute of Architects. Warning: This AIA MasterSpec based document is protected by U.S.

Copyright Law and International Treaties. A valid, current MasterSpec license is required for editing or use of this document.

32 13 13 CONCRETE PAVING

32 13 16 DECORATIVE CONCRETE PAVING

32 13 73 CONCRETE PAVING JOINT SEALANTS

32 14 00 UNIT PAVING

32 14 43 POROUS UNIT PAVING

32 17 13 PARKING BUMPERS

32 17 16 MANUFACTURED TRAFFIC-CALMING DEVICES

32 17 23 PAVEMENT MARKINGS

32 17 26 TACTILE WARNING SURFACING

32 18 13 SYNTHETIC GRASS SURFACING

32 18 16.13 PLAYGROUND PROTECTIVE SURFACING

32 31 13 CHAIN LINK FENCES AND GATES

32 31 13.53 HIGH-SECURITY CHAIN LINK FENCES AND

GATES

32 31 16 WELDED WIRE FENCES AND GATES

32 31 19 DECORATIVE METAL FENCES AND GATES

32 31 19.53 DECORATIVE METAL SECURITY FENCES AND

GATES

32 31 29 WOOD FENCES AND GATES

32 31 32 COMPOSITE WOOD FENCES AND GATES

32 32 23 SEGMENTAL RETAINING WALLS

32 33 00 SITE FURNISHINGS

32 84 00 PLANTING IRRIGATION

32 91 13 SOIL PREPARATION

32 91 15 SOIL PREPARATION (PERFORMANCE

SPECIFICATION)

32 92 00 TURF AND GRASSES

32 93 00 PLANTS

32 96 00 TRANSPLANTING

DIVISION 33 - UTILITIES

33 05 00 COMMON WORK RESULTS FOR UTILITIES

33 11 13 POTABLE WATER SUPPLY WELLS

33 14 15 SITE WATER DISTRIBUTION PIPING

33 31 15 SITE SANITARY SEWERAGE PIPING

33 32 00 SITE PACKAGED SEWAGE PUMPING

STATIONS

33 42 00 STORMWATER CONVEYANCE

33 46 00 SUBDRAINAGE

33 47 13 POND AND RESERVOIR LINERS

33 71 49.13 OVERHEAD MEDIUM-VOLTAGE WIRING

33 77 53 MEDIUM-VOLTAGE UTILITY RECLOSERS

END OF TABLE OF CONTENTS

CADGS - Technical Specifications

CA-TS-01 GENERAL REQUIREMENTS

01 00 00

SECTION 01 00 00 - GENERAL REQUIREMENTS

PART 1 - GENERAL (Not Used) PART 2 - PRODUCTS (Not Used) PART 3 - EXECUTION (Not Used)

END OF SECTION 01 00 00

CADGS - Technical Specifications

CA-TS-01 STRUCTURE DEMOLITION

02 41 16

SECTION 02 41 16 - STRUCTURE DEMOLITION

PART 1 - GENERAL

1.1 SUMMARY

A. The Work of this Section Includes:

1. Demolition and removal of buildings or structures.

2. Demolition and removal of site improvements.

3. Abandoning in-place below-grade construction.

4. Removing below-grade construction.

5. Disconnecting, capping or sealing, and abandoning in-place site utilities.

6. Disconnecting, capping or sealing, and removing site utilities.

7. Salvaging items for reuse by Owner.

B. Related Requirements:

1. Section 011000 "Summary" for use of the premises and phasing requirements.

2. Section 013200 "Construction Progress Documentation" for preconstruction photographs taken before building demolition.

3. Section 024119 "Selective Demolition" for partial demolition of buildings, structures, and site improvements.

4. Section 311000 "Site Clearing" for site clearing and removal of above- and below-grade site improvements that are not part of building demolition.

1.2 PREINSTALLATION MEETINGS

A. Predemolition Conference: Conduct conference at [Project site]<Insert location>.

1. Inspect and discuss condition of construction to be demolished.

2. Review structural load limitations of existing structures.

3. Review and finalize building demolition schedule and verify availability of demolition personnel, equipment, and facilities needed to make progress and avoid delays.

4. Review and finalize protection requirements.

5. Review procedures for [noise control][and][dust control].

6. Review procedures for protection of adjacent buildings.

7. Review storage, protection, and accounting for items to be salvaged and returned to Owner.

1.3 INFORMATIONAL SUBMITTALS

A. Qualification Statements: For [refrigerant recovery technician][specialty demolition contractor].

B. Engineering Survey: Submit engineering survey of condition of building.

CADGS - Technical Specifications

CA-TS-01 STRUCTURE DEMOLITION

02 41 16

C. Survey of Existing Conditions: Submit survey.

D. Proposed Protection Measures: Submit report, including Drawings, that indicates the measures proposed for protecting individuals and property [, for environmental protection][, for dust control][and][, for noise control]. Indicate proposed locations and construction of barriers.

1. Adjacent Buildings: Detail special measures proposed to protect adjacent buildings to remain [ including means of egress from those buildings].

E. Schedule of Building Demolition Activities: Indicate the following:

1. Detailed sequence of demolition work, with starting and ending dates for each activity.

2. Temporary interruption of utility services. Indicate how long services will be interrupted.

3. Coordination for shutoff and capping [ or re-routing] of utility services.

F. Statement of Refrigerant Recovery: Signed by refrigerant recovery technician responsible for recovering refrigerant, stating that all refrigerant that was present was recovered and that recovery was performed in accordance with EPA regulations.

Include name and address of technician and date refrigerant was recovered.

1.4 CLOSEOUT SUBMITTALS

A. Inventory: Submit a list of items that have been removed and salvaged.

1.5 QUALITY ASSURANCE

A. Refrigerant Recovery Technician Qualifications: [Type I][Type II][Type III][Universal] certified by an EPA-approved certification program.

B. Specialty Demolition Contractor Qualifications: A competent person [licensed by the authority having jurisdiction,] who has training, knowledge, or experience in the use of each type of blasting method used and in the field of transporting, storing, handling, and using explosives; and has a working knowledge of state and local laws and regulations pertaining to explosives.

1.6 FIELD CONDITIONS

A. Buildings to be demolished will be vacated and their use discontinued before start of the Work.

B. Buildings immediately adjacent to demolition area will be occupied. Conduct building demolition so operations of occupied buildings will not be disrupted.

1. Provide not less than [72]<Insert number> hours' notice of activities that will affect operations of adjacent occupied buildings.

2. Maintain access to existing walkways, exits, and other facilities used by

CADGS - Technical Specifications

CA-TS-01 STRUCTURE DEMOLITION

02 41 16 occupants of adjacent buildings.

a. Do not close or obstruct walkways, exits, or other facilities used by occupants of adjacent buildings without written permission from authorities having jurisdiction.

C. Conditions existing at time of inspection for bidding purpose will be maintained by Owner as far as practical.

1. Before building demolition, Owner will remove the following items:

a. <Insert items to be removed by Owner>.

D. Hazardous Materials:

1. It is not expected that hazardous materials will be encountered in the Work.

a. Hazardous materials will be removed by Owner before start of the Work.

b. If materials suspected of containing hazardous materials are encountered, do not disturb; immediately notify Architect and Owner. Hazardous materials will be removed by Owner under a separate contract.

2. Hazardous materials are present in buildings and structures to be demolished. A report on the presence of hazardous materials is [on file][included in Section 003126 "Existing Hazardous Material Information"] for review and use. Examine report to become aware of locations where hazardous materials are present.

a. Hazardous material remediation is specified in Section <Insert Section number> " <Insert Section title>."

b. Do not disturb hazardous materials or items suspected of containing hazardous materials except under procedures specified in Section <Insert Section number> " <Insert Section title>."

c. Owner will provide material safety data sheets for hazardous materials that are known to be present in buildings and structures to be demolished because of building operations or processes performed there.

E. On-site sale of removed items or materials is not permitted.

PART 2 - PRODUCTS

2.1 PERFORMANCE REQUIREMENTS

A. Regulatory Requirements: Comply with governing EPA notification regulations before beginning demolition. Comply with hauling and disposal regulations of authorities having jurisdiction.

B. Standards: Comply with ANSI/ASSP A10.6 and NFPA 241.

CADGS - Technical Specifications

CA-TS-01 STRUCTURE DEMOLITION

02 41 16

2.2 SOIL MATERIALS

A. Satisfactory Soils: Comply with requirements in Section 312000 "Earth Moving."

END OF SECTION 02 41 16

CADGS - Technical Specifications

CA-TS-01 SELECTIVE DEMOLITION

02 41 19

SECTION 02 41 19 - SELECTIVE DEMOLITION

PART 1 - GENERAL

1.1 SUMMARY

A. The Work of this Section Includes:

1. Demolition and removal of selected portions of exterior or interior of building or structure and site elements.

2. Removal and salvage of existing items for delivery to Owner and removal of existing items for reinstallation.

1.2 MATERIALS OWNERSHIP

A. Unless otherwise indicated, demolition waste becomes property of Contractor.

1.3 COORDINATION

A. Arrange selective demolition schedule so as not to interfere with Owner's operations.

1.4 PREINSTALLATION MEETINGS

A. Predemolition Conference: Conduct conference at Project site.

1. Inspect and discuss condition of construction to be selectively demolished.

2. Review structural load limitations of existing structure.

3. Review requirements of work performed by other trades that rely on substrates exposed by selective demolition operations.

4. Review areas where existing construction is to remain and requires protection.

5. Review and finalize protection requirements.

6. Review procedures for noise control and dust control.

7. Review storage, protection, and accounting for items to be removed for salvage or reinstallation.

1.5 INFORMATIONAL SUBMITTALS

A. Survey of Existing Conditions: Submit survey.

B. Proposed Protection Measures: Submit report, including Drawings, that indicates the measures proposed for protecting individuals and property [, for environmental protection][, for dust control][and][, for noise control]. Indicate proposed locations and construction of barriers.

C. Schedule of Selective Demolition Activities: Indicate the following:

CADGS - Technical Specifications

CA-TS-01 SELECTIVE DEMOLITION

02 41 19

1. Detailed sequence of selective demolition and removal work, with starting and ending dates for each activity. Ensure Owner's on-site operations are uninterrupted.

2. Temporary interruption of utility services. Indicate how long utility services will be interrupted.

3. Coordination for shutoff, capping, and continuation of utility services.

4. Use of elevator and stairs.

5. Coordination of Owner's continuing occupancy of portions of existing building and of Owner's partial occupancy of completed Work.

D. Statement of Refrigerant Recovery: Signed by refrigerant recovery technician responsible for recovering…