ISD-E_Section 087100 Door Hardware.pdf

SECTION 087100 – DOOR HARDWARE

1. FURNISH HARDWARE SPECIFIED ON DRAWINGS. EXAMINE ALL THE DRAWINGS AND SPECIFICATIONS AND INCLUDE ALL THE HARDWARE REQUIRED TO COMPLETE WORK. HARDWARE NOT SPECIFICALLY MENTIONED MUST BE SUPPLIED AND MUST CORRESPOND IN QUALITY, SIZE, AND FINISH THAT DESCRIBED FOR

CORRESPONDING LOCATIONS.

2. VERIFY ALL HARDWARE LISTED ON HARDWARE SCHEDULE IS COMPATIBLE WITH DOORS AND FRAMES

SPECIFIED.

3. SUBMIT A COMPLETE HARDWARE SCHEDULE WITH CATALOG CUT OF EACH ITEM OF HARDWARE SPECIFIED TO

FERMILAB FOR APPROVAL.

4. ALL HARDWARE ITEMS SHALL BE PACKAGED SEPARATELY, AND LABELED WITH THE MANUFACTURER'S NAME, TYPE, NUMBER AND NAME OF THE ITEM. TAG ALL THE ITEMS WITH THE SAME HARDWARE SET NUMBER AS THAT CARRIED IN THE APPROVED HARDWARE SCHEDULE. EACH CONTAINER OF PACKAGE SHALL ALSO CONTAIN NECESSARY SCREWS, KEYS, BRACKETS, ETC. AND INSTRUCTIONS FOR INSTALLATION AND INSTALLATION TEMPLATES FOR SPOTTING MORTISING TOOLS. A SET OF TEMPLATES SHALL BE PROVIDED TO THE HOLLOW

METAL DOOR FABRICATOR.

5. ALL HARDWARE SHALL BE GUARANTEED FOR A PERIOD OF (2) YEARS FROM THE DATE OF ACCEPTANCE.

6. SUPPLIER RESPONSIBILITIES:

a. THE SUPPLIER IS RESPONSIBLE FOR THOROUGHLY DETAILING THE ENTIRE PROJECT TO ASSURE THAT

THE ITEMS SPECIFIED WILL PROPERLY FUNCTION IN THE INDICATED LOCATIONS.

b. SHOULD THE ITEMS SPECIFIED NOT WORK PROPERLY, IT IS THE RESPONSIBILITY OF THE SUPPLIER TO

FURNISH SUITABLE ITEMS OF COMPARABLE QUALITY AS APPROVED BY THE ARCHITECT TO THOSE BEING

FURNISHED THROUGHOUT THE PROJECT.

7. INSTALLER QUALIFICATIONS: AN EXPERIENCED INSTALLER WHO HAS COMPLETED DOOR HARDWARE SIMILAR

IN MATERIAL, DESIGN, AND EXTENT TO THAT INDICATED FOR THIS PROJECT AND WHOSE WORK HAS RESULTED

IN CONSTRUCTION WITH A RECORD OF SUCCESSFUL IN-SERVICE PERFORMANCE.

8. SOURCE LIMITATIONS: OBTAIN EACH TYPE AND VARIETY OF DOOR HARDWARE FROM A SINGLE

MANUFACTURER, UNLESS OTHERWISE INDICATED.

9. HARDWARE SETS:

a. THE HARDWARE SETS REPRESENT THE DESIGN INTENT AND DIRECTION OF THE FFDG AND ARCHITECT.

THEY ARE A GUIDELINE ONLY AND SHOULD NOT BE CONSIDERED A DETAILED HARDWARE SCHEDULE.

DISCREPANCIES, CONFLICTING HARDWARE AND MISSING ITEMS ARE TO BE BROUGHT TO THE

ATTENTION OF FERMILAB WITH CORRECTIONS MADE PRIOR TO THE END OF THE BIDDING PROCESS.

b. OMITTED ITEMS NOT INCLUDED IN HARDWARE SETS ARE TO BE SCHEDULED WITH THE APPROPRIATE

ADDITIONAL HARDWARE REQUIRED FOR PROPER APPLICATION AND FUNCTIONALITY.

10. FIRE-RATED DOOR ASSEMBLIES: WHERE FIRE-RATED DOORS ARE INDICATED, PROVIDE DOOR HARDWARE

COMPLYING WITH NFPA 80 THAT IS LISTED AND LABELED BY A QUALIFIED TESTING AGENCY, FOR FIRE- PROTECTION RATINGS INDICATED, BASED ON TESTING AT POSITIVE PRESSURE IN ACCORDANCE WITH NFPA

252 OR UL 10C.

11. MEANS OF EGRESS DOORS:

a. LATCHES DO NOT REQUIRE MORE THAN 15 LBF (67 N) TO RELEASE THE LATCH.

b. LOCKS DO NOT REQUIRE USE OF A KEY, TOOL, OR SPECIAL KNOWLEDGE FOR OPERATION.

12. HINGES:

a. COMPLY WITH ANSI/BHMA A156.1

b. STEEL BASE, BALL-BEARING TYPE

c. PROVIDE 1 HINGE FOR EVERY 30 ” OF DOOR HEIGHT.

d. BASIS OF DESIGN:

1. MANUFACTURER: MCKINLEY OR EQUAL

2. MODEL: TA2714 4.5 X 4.5

3. OPTIONS: NON-REMOVABLE PIN

4. FINISH: SATIN STAINLESS

5. PRODUCT NUMBER: 652

13. FLUSH BOLTS AND ACCESSORIES:

a. AUTOMATIC FLUSH BOLTS: ANSI/BHMA A156.3, TYPE 25, GRADE 1; MINIMUM 3/4- INCH (19-MM) THROW;

WITH DUST-PROOF STRIKES; DESIGNED FOR MORTISING INTO DOOR EDGE. INCLUDE WEAR PLATES.

b. PROVIDE ITEMS AS MANUFACTURED BY ONE OF THE FOLLOWING:

1. TRIMCO (TR)

2. ROCKWOOD (RO)

3. IVES (IV)

c. BASIS OF DESIGN:

1. MANUFACTURER: ROCKWOOD

2. MODEL: 2842/2942

3. PRODUCT NUMBER: 630

14. EXIT DEVICES AND AUXILIARY ITEMS

a. EXIT DEVICES AND AUXILIARY ITEMS: ANSI/BHMA A156.3.

b. BASIS-OF-DESIGN PRODUCT: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, BASIS OF DESIGN: VON

DUPRIN 35A-F RIM FIRE EXIT DEVICE SERIES PANIC DEVICE WITH RODS FINISH TO BE 628 ANODIZED

ALUMINUM.

c. FOR DOUBLE DOORS U TO 8’ X 10 BASS OF DESIGN: SUBJECT TO COMPLIANCE WITH REQUIREMENTS, BASIS OF DESIGN: VON DUPRIN 3527A-F SURFACE MOUNTED VERTICAL ROD FIRE EXIT DEVICE. FINISH TO

BE 628 ANODIZED ALUMINUM.

15. DOOR TRIM AND PROTECTIVE PLATES:

a. COMPLYING WITH BHMA A156.6.

b. PROVIDE KICK, MOP AND ARMOR PLATES FABRICATED FROM .050 GAUGE STAINLESS STEEL WITH

BEVELED EDGES. PROVIDE HEIGHTS AND WIDTHS INDICATED IN THE HARDWARE SETS.

c. PUSH PLATES, PULL PLATES, DOOR PULLS AND OTHER MISCELLANEOUS DOOR TRIM TO BE FURNISHED

AS SPECIFIED.

d. PROVIDE ITEMS AS MANUFACTURED BY ONE OF THE FOLLOWING:

1. TRIMCO (TR)

2. IVES (IV)

3. ROCKWOOD (RO) .

16. ACCESSORIES FOR PAIRS OF DOORS

a. COORDINATORS: ANSI/BHMA A156.3; CONSISTING OF ACTIVE-LEAF, HOLD-OPEN LEVER, AND INACTIVE- LEAF RELEASE TRIGGER; FABRICATED FROM STEEL WITH NYLON-COATED STRIKE PLATES; WITH BUILT-

IN, ADJUSTABLE SAFETY RELEASE.

i. BASIS OF DESIGN:

1. MANUFACTURER: ROCKWOOD

2. MODEL NUMBER: 2600 SERIES

3. PRODUCT NUMBER: 628

b. CARRY-OPEN BARS: ANSI/BHMA A156.3; PREVENT THE INACTIVE LEAF FROM OPENING BEFORE THE

ACTIVE LEAF; PROVIDE POLISHED BRASS OR BRONZE

c. CARRY-OPEN BARS WITH STRIKE PLATE FOR INACTIVE LEAVES OF PAIRS OF DOORS UNLESS

AUTOMATIC OR SELF-LATCHING BOLTS ARE USED.

d. ASTRAGALS: ANSI/BHMA A156.22.

17. EXTERIOR DOOR SWEEP: APPLY TO BOTTOM OF DOOR, FORMING SEAL WITH THRESHOLD WHEN DOOR IS

CLOSED.

a. BASIS OF DESIGN:

1. MANUFACTURER: PEMKO OR EQUAL

2. MODEL NUMBER: 18061CNB

18. THRESHOLDS

a. SET THRESHOLDS FOR EXTEROR DOORS AND OTHER DOORS INDCATED IN FULL BED OF SEALANT.

19. STOPS: ROVIDE FLOOR STOPS FOR DOORS UNLESS WALL OR OTHER TYPE STOPS ARE NDICATED N DOOR

HARDWARE SCHEDULE. DO NOT MOUNT FLOOR STOS WHERE THEY WILL IMPEDE TRAFFIC.

20. SURFACE CLOSERS

a. ANSI/BHMA A156.4; RACK-AND-PINION HYDRAULIC TYPE WITH ADJUSTABLE SWEEP AND LATCH SPEEDS

CONTROLLED BY KEY-OPERATED VALVES AND FORGED-STEEL MAIN ARM. COMPLY WITH THE

MANUFACTURER’S WRITTEN INSTRUCTIONS FOR SIZE OF DOOR CLOSERS DEPENDING ON SIZE OF

DOOR, EXPOSURE TO WEATHER, AND ANTICIPATED FREQUENCY OF USE.

b. PROVIDE FACTORY-SIZED CLOSERS, ADJUSTABLE TO MEET FIELD CONDITIONS AND REQUIREMENTS

FOR OPENING FORCE.

c. PROVIDE SURFACE MOUNTED DOOR CLOSERS AS MANUFACTURED BY ONE OF THE FOLLOWING:

1. SARGENT 351 SERIES

2. NORTON 7500 SERIES

3. LCN 4040XP SERIES

4. CORBIN RUSSWIN DC6000 SERIES