c1fb5c05-26b0-4cf5-a477-34d86dbf9e01.pdf
PDF 73 KB Posted
- Attached to
- Cross Gallery Southwest Annex Refresh Project
- Solicitation number
- ISD-371462-RO
About this file
This document is a detailed architectural design guide from Fermilab ISD-Engineering for a single exterior hollow metal door (HW-1) with fire rating specifications. The guide specifies a 3'-0" x 7'-0" x 1-3/4" galvanized steel door manufactured by Steelcraft or an approved equal, with a UL-labeled fire-rated core using vertical steel stiffeners or laminated mineral board. The door features an entrance function that can be unlocked by a key from the outside and is always unlocked from the inside.
The specification includes comprehensive hardware requirements such as 1-1/2 pair of McKinley hinges with non-removable pins, a Best lockset with entrance function, a Von Duprin panic hardware set, a Norton closer, Zero weather-stripping, a Pemko door bottom sweep, a Hager drip cap, a Rockwood flush bolt, a Zero threshold, an optional Ives kick-plate, and various door stop options. A special note indicates that cylinders will use interchangeable core, small format, 7-pin tumbler inserts, with Fermilab responsible for final cores and keys after the construction period.
View the file
Other files
Show all 25
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
ISD Engineering – Architectural General Section 3.0
Fermilab ISD-Engineering Design Guides Page 2 of 13
WARNING: This manual is subject to change. The current version is maintained on FESS Section website. Rev. 1, 08/2025
Hollow Metal Door – Single Exterior (HW-1)
1 HOUR FIRE RATED – 45 MINUTE LABEL
2 HOUR FIRE RATED – 90 MINUTE LABEL
Single Door – 3’-0” x 7’-0” x 1-3/4”
Use galvanized steel door and frame
Fire rated door with UL label
Manufactured by Steelcraft or approved equal.
Fire-rated core: manufacturer's standard vertical steel stiffener and/or laminated mineral board core for fire-rated doors.
Entrance function – unlocked by turning key outside, always unlocked from the inside
Item Description Comments
Hinges 1-1/2 Pair Hinges
Manufacturer: Mckinley Or Equal
Model: TA2714 4.5 X 4.5
Options: Non-Removable Pin
Finish: Satin Stainless
Product Number: 652
If door is higher than 7 ‘ or wider than 3’ look into the use of additional hinges or larger hinges.
Steel Base, Ball-Bearing Type.
Provide 1 Hinge For Every 30 ” Of
Door Height.
Lockset 1 Ea. (Function: Entrance)
Manufacturer: Best 93K7AB15D / S3 / 626 *
This is not panic hardware. If building occupancy requires see panic hardware set
Panic Hardware 1 set- Von Duprin 35a-F Rim Fire Exit Device series panic device with rods.
Finish to be 628 anodized aluminum.
Lever to be Von Duprin 360L.
Closer 1 Ea. 3. NORTON 7500 SERIES
Finish to be 689.
Pull or push side jamb mounting depending on the swing of the door.
Weather-stripping 1 Set - Zero #314AA. At exterior door
Door Bottom
Sweep
1 Ea. –
Manufacturer: Pemko Or Equal
Model Number: 18061CNB
At exterior door
Drip Cap 1 Ea.- Hager. At exterior door
ISD Engineering – Architectural General Section 3.0
Fermilab ISD-Engineering Design Guides Page 3 of 13
WARNING: This manual is subject to change. The current version is maintained on FESS Section website. Rev. 1, 08/2025
Item Description Comments
Flush Bolt Manufacturer: Rockwood
Model: 2842/2942
Product number: 630
Automatic flush bolts: ANSI/BHMA
A156.3, type 25, grade 1; minimum
3/4- inch (19-mm) throw; with dust-proof strikes; designed for mortising into door edge. Include wear plates.
Thresholds 1 Ea.- Zero #545A.
Finish Anodized Aluminum
Set threshold for doors in full be of sealant
Kick-plate
(if desired)
Ives .050 Stainless Steel Beveled 4 Sides with
Countersunk Screws. 10” High x Width of Door
Less 2”.
Door Stop 1 Ea. – Floor Stop – Ives FS13 Dome Stop US
26D for use without threshold or
Ives FS17 Dome Stop for use without threshold or
1 Ea. – Wall stop – Ives WS402CCV US 26D or
1 Ea. – Plunger –Ives FS1154 US 26D
Select one type of stop
* Cylinders: Equip locks with cylinders for interchangeable core, small format, 7 pin tumbler inserts. Furnish only temporary inserts for the construction period, and remove these when directed. Final cores and keys for installation will be Fermilab's responsibility.
File details come from the government source that posted it. Updated .