348175 Floor Epoxy Scope of Work.docx
DOCX document 13 KB Posted
- Attached to
- Static Dissipative Flooring
- Solicitation number
- ISD-348175-SCM
About this file
This document is a Scope of Work for a federal contract opportunity to install static dissipative epoxy flooring in the G-WEST (G723) laboratory at the Fermi National Accelerator Laboratory.
The key details are:
- Scope: Grind and shotblast the existing concrete floor, install Dur-A-Flex Dur-A-Gard ESD Primer with copper grounding tape, Dur-A-Flex ESD Gard, and Dur-A-Flex Armor Top ESD urethane. Total area is approximately 3,000 square feet.
- Requirements: The ESD protective flooring must have a resistance range of 10^6-10^9 Ohms.
- Tasks: 1) Grind concrete floor, 2) Honor service and vibration trenches, 3) Slope floor around trenches, 4) Prime floor, 5) Base coat with ESD epoxy, 6) Lay copper grounding, 7) Finish and clean up.
- Period of Performance: 30 days
- Contractor must have direct dock access and provide their own power.
- Pricing is based on an "open box install" assuming walls have been installed.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Floor Pic 1.jpg | JPG image | |
| Amendment 01.pdf | ||
| Floor Pic 3.jpg | JPG image | |
| Floor Pic 2.jpg | JPG image | |
| 013100_ESH_Requirements_3-2022 (1).docx | DOCX document | |
| FL-42 (Rev 12.22) - Payment Bond.pdf | ||
| Construction Insurance Requirements.pdf | ||
| Section 013300_Submittals.docx | DOCX document | |
| SARC_Subcontractor Annual RepsCerts Rev 3.pdf | ||
| FL-41 (Rev 12.22) - Bid Bond.pdf | ||
| Section 014100 Quality Requirements - March 2022.pdf | ||
| Proposal Form.doc | DOC document | |
| 010010_General_Requirements_3_2022 (1).docx | DOCX document | |
| WD IL20240008 (1-05-2024).pdf | ||
| Statement and Acknowledgment SF1413.pdf | ||
| ESH_Requirements_3-2022 (1).docx | DOCX document | |
| PUR-466_Proposal Certifications.pdf | ||
| FRA General Terms and Conditions for Construction (03.2024).pdf | ||
| Fermilab Subcontractor Safety Information Questionnaire.pdf | ||
| 1.0 RFP Instructions to Offerors.pdf |
Show all 20
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Scope of Work: STATIC DISSIPATIVE FLOORING Project: Room G7223, West Table Clean Room Area Requisition: 348175
The general scope of this project is to prepare and lay ESD protective epoxy floor in G-WEST (G723) laboratory in the HEERC building (approximately 3,000 sqf).
Grind and/or shotblast existing surface for proper adhesion of applied product Install Dur-A-Flex Dur-A-Gard ESD Primer with copper grounding tape, grounding points provided by others.
Install Dur-A-Flex ESD Gard Install Dur-A-Flex Armor Top ESD urethane Per site visit all existing caulk to remain, installation will terminate at caulk lines CCI will require specific power as noted below, CCI will provide pigtails to be wired by others.
CCI must have direct dock access for deliveries Installation duration 5-6 days working all areas simultaneously Pricing based on open box install if walls have been installed need to see wall plan and/or visit site.
Requirements: ESD protective floor within the range 10^6-10^9 Ohms.
Tasks:
1. Grind existing concrete floor to remove sealer and open up new concrete
2. Honour service trenches and vibration isolation trenches
3. Slope floor to level floor around trenches
4. Prime floor with penetrating moisture tolerant primer
5. Base coat floor with appropriate ESD protective epoxy
6. Lay out copper stripes and ground floor
7. Finish and clean-up floor.
Period of Performance: 30 Days
File details come from the government source that posted it. Updated .