Appendix_B_-_Performance_and_Techincal_Specifications_Final.pdf

Appendix B: Performance and Technical Specifications

APPENDIX B

PERFORMANCE AND TECHNICAL SPECIFICATIONS

TABLE OF CONTENTS: APPENDIX B

0.1 General Requirements

1.0 Systems Furniture, Teaming Areas, and Filing

2.0 Casegoods and Conference Rooms

3.0 Seating

4.0 Storage

5.0 Ancillary Furniture

6.0 High Density Filing

7.0 Wellness Furniture

8.0 Information Technology Lab

9.0 Mail Room

10.0 Accessories and Artwork

11.0 Packaged Offices, Workstations, Conference Rooms, and Common Spaces

12.0 Demountable Walls

13.0 Signage

14.0 Product Testing Requirements

15.0 Glossary

0.1

GENERAL REQUIREMENTS

0.1 GENERAL REQUIREMENTS

0.1.1 All products shall be manufactured as new products. Used, reworked, or refurbished products are not acceptable.

0.1.2 All products shall meet or exceed all applicable ANSI/BIFMA performance standards.

0.1.3 One set of any tool(s) required to assemble the products shall be provided.

0.1.4 All hardware required for the installation of any components shall be provided.

0.1.5 All product sizes shall conform to dimensions indicated in this section. Sizes may differ +/-

2” per manufacturer.

0.1.6 Offeror shall comply with the “Typical Private Offices and Workstations” line drawings provided in this section.

0.1.7 Offeror shall comply with the “Electrical and Data Cable Management Configuration” as provided in this section.

0.1.8 Offeror shall comply with the “Electrical Wiring Requirements” provided in this section.

0.1.9 Offeror’s product line shall be capable of mounting and integrating into a universal demountable wall product.

0.1.10 All labor, material, tools and handling costs associated with warranty work shall be at no cost to the government. The manufacturer shall commit to non-obsolescence of specified new products for a minimum of fifteen (15) years from delivery. The warranty coverage shall be conveyed to the government upon final occupancy.

All products shall have a full twelve (12) year warranty covering, all materials and worksmanship, except as follows:

Seating Mechanisms that move – 10 years

Seating Glides and Castors – 10 years

Task Lights – 5 years

(Except ballast, lamp, and power supply to be 1 year)

Electrical Components – 5 years

Stack Chair Frames – 10 years

Textile Upholstery – 5 years

1.0

GROUP 1

SYSTEMS FURNITURE, TEAMING AREAS, AND FILING

1.0 GROUP 1 – SYSTEMS WORKSTATION SPECIFICATIONS

See system specification below.

1.1 GROUP A – SPLINE PANELS – INFORMATION TECHNOLOGY (IT) RACEWAYS

AND DEVICES

1.1.1 Faceplates for IT devices are not part of the furniture contract. Power faceplates shall be provided under the furniture contract. Boxes are also to be provided by the furniture supplier for any furniture that employs the use of a pop-up or table top box.

1.1.2 A under desk top cable management system shall be provided to manage computer cables tight under the work surface so that they are not visible.

1.1.3 Systems Furniture IT Raceways

1.1.4 The systems panel shall accommodate 4 separate IT raceways. The systems panel shall have the capability to expand to a fifth raceway. The addition of the fifth IT raceway shall not alter the appearance, height, or material of the systems panel. Raceway design may allow cables to be routed through or around vertical frame supports provided the cross sectional area of the raceway at any point is not less than specified below. The preferred method of raceway design is a 3-sided open trough; however, other raceway designs that provide adequate support for the cables and maintain the separation requirements listed below shall be acceptable. Cables shall not be visible or accessible between systems panel connection points.

1.1.5 All IT raceways are required to consistently maintain no less than a 6” separation to meet IT security classification requirements. A separation is required at crossing points and vertical pathways. IT raceways must maintain a 2” separation from electrical raceways.

1.1.6 Two of the four IT raceways shall be located below the work surface and two IT raceways shall be located above the work surface. One raceway shall be located within 6" below the work surface. Future fifth raceway location shall be identified by the vendor.

1.1.7 All IT raceways shall be sized to accommodate the highest number of cables feeding the spline wall for a cluster of workstations from cable in feeds at not more than a 40% fill. Each workstation shall receive the following cable distribution:

a. Two (2)-each CAT-6A copper cables. Each cable has a cross sectional diameter of 0.31 inches.

b. Three (3)-each four-strand, multi-mode fiber optic cables with pre-terminated fiber-optic

LC connectors. Each cable has a cross-sectional diameter of 0.17 inches.

1.1.8 All IT cables will be furnished, installed and terminated under another contract.

1.1.9 All raceways must satisfy any bend radius requirements of the cables listed above, as well as any applicable TIA-569-B Commercial Building Standards for Telecommunication Pathways and Spaces.

1.1.10 Each cluster of workstations requires a separate infeed for each IT cable classification. This will require anywhere from four (4) to six (6) in feeds per cluster.

1.1.11 All raceways shall require three punch-outs at each workstation. All punch-outs will be spaced 20” apart and require a blank cover plate.

1.2 GROUP 1 – SPLINE PANELS – ELECTRICAL POWER RACEWAY AND DEVICES

1.2.1 The systems panel shall be supplied with two (2) pre-wired electrical power raceways. One power infeed shall provide power for not more than a 4 - workstation cluster. The power infeed shall be an 8-wire, 3-circuit system (3 hot, 3 neutral and 2 grounds). One (1) hot wire and one (1) neutral wire shall feed both furniture receptacles designated A and B (above work surface for “convenience” power) for a total of eight (8) duplex receptacles per circuit. One

(1) hot wire and one (1) neutral wire shall feed furniture receptacles designated C (below the work surface for “computer” power) for a total of four (4) duplex receptacles per circuit. One

(1) hot wire and one (1) neutral wire shall feed furniture receptacles designated D (below the work surface for “computer” power) for a total of four (4) duplex receptacles per circuit. A and B receptacles shall share one of the ground wires and C and D receptacles shall share one of the ground wires.

1.2.2 The raceway for receptacles A-B shall be located above the work surface and the raceway for receptacles C-D shall be located below the work surface.

1.2.3 A multi-outlet distribution center (i.e. Power Strip) with an integral surge protector shall be provided for each workstation.

1.2.4 The furniture shall provide the ability for power outlets to be added, removed or relocated along cubicle panel. Power faceplates shall be provided under the furniture contract.

1.2.5 The electrical system shall be UL approved.

1.2.6 Power whips shall be provided with a minimum length of 6 feet, with the capability to be field cut to length for hardwiring into building power distribution system.

1.2.7 Receptacles shall be numbered (coded) with circuit identification. The C and D labeled receptacles shall be color coded differently than the other receptacles.

1.3 GROUP 1 - WORK SURFACES SPECIFICATIONS

1.3.1 Work surfaces with unsupported knee spaces of 60” or greater in length shall be steel reinforced. Work surfaces shall have the ability to mount off module.

1.3.2 Work surfaces shall be available in wood and laminate finish for rectangular, curved, bullet, transaction, and corner surfaces.

1.3.3 Laminate work surface edges shall be post-formed in a single sheet of material that wraps the front edge and continues under the work surface, creating a clean protective edge.

1.3.4 An adjustable height work surface shall be available for use in limited applications to meet physically challenged personnel needs. The method of adjustment shall be pneumatic height adjusted.

1.4 GROUP 1 – FRAME AND TILE SPECIFICATIONS

1.4.1 Frames shall be stackable. Stacking frames shall be able to support hanging components on both sides. The frame shall be a minimum of 16 gauge steel including supports, top and bottom rails and shall have fully welded or post and lintel locking junctions. Frames shall allow for a full range of component mounting heights, with slots every ¾” to 1”. Frames shall include self leveling or single-tool adjustable glides. All exposed ends of frames shall be covered with hard surface finished trim pieces. The system shall include connectors that provide 2, 3, 4 way or universal frame connections with full finished end caps in wood or extruded aluminum. All frames shall accommodate off-module connections. Frames shall have the ability to be converted from powered to non-powered and vice versa.

1.4.2 Frames shall be available in a minimum of two heights 42”and 54”, +/- 3 inches high.

1.4.3 Frame widths shall be available in 18”, 24”, 30”, 36”, and 42” widths.

1.4.4 Tile finishes shall include paint, perforated steel, tackable, acoustical, and wood, marker board, glass, and open frame. The following accessories shall be available:

Tack boards

Rail tiles or tool bars with accessories

Paper trays

Marker boards

1.5 GROUP 1 – SHELVES AND STORAGE CABINETS SPECIFICATIONS

1.5.1 Storage units shall be constructed of a minimum of 20-gauge steel with a baked enamel surface, or powder coat paint finish. Files accommodate letter or legal filing capabilities. All necessary hanging rails shall be included as a part of the installation. User shall be able to open the cabinet door from a sitting position either by a simple touch type/easy open and easy close lift or a hinged door application. Cabinets shall be easily accessible with ADA compliant pulls.

1.5.1 Open shelving shall have the capability to convert to closed cabinets storage on site. Shelves shall be adjustable. Overhead bins must be able to have over the case or hinged door.

1.5.2 Storage cabinets in the private offices shall have the same wood veneer finishes (fronts only) and the storage cabinets in the open workstations shall have painted surfaces to match other components in the surrounding area.

1.5.3 Storage units shall have leveling glides. Mobile, fixed and freestanding storage must be able to have box/file, box/box/file or file/file configurations.

1.6 GROUP 1 - KEYING SPECIFICATIONS

1.6.1 All locking devices within the station shall be keyed alike.

1.7 GROUP 1 – TASK LIGHTING SPECIFICATIONS

1.7.1 Task lights shall be provided and equipped w/ low wattage LED lamps.

1.7.2 Tasks lights shall be controlled via an individual on/off occupancy (heat) sensor controller at each work station.

1.7.3 Task lights shall be designed to be compatible with the system furniture and shall be available in both panel mounted, freestanding, and mounted under overhead storage components.

1.8 GROUP 1 – KEYBOARD TRAY SPECIFICATIONS

1.8.1 Ergonomic keyboard trays shall be available that accommodates keyboards of industry standard length.

1.8.2 Keyboard tray adjustments shall be spring force assisted or pneumatic.

1.8.3 Tray shall tilt up to 10 degrees, front to back and reverse.

1.8.4 Keyboard tray shall adjust at least 6 inches vertically.

1.8.5 Keyboard tray arm shall recess fully and pivot out of the way under the work surface for storage.

1.8.6 A non-handed attachable mouse tray with a 10 degree tilt and a palm/wrist rest shall be available.

1.9 GROUP 1 – MISCELLANEOUS SPECIFICATIONS

1.9.1 Pivot arm for flat screen monitors that articulates freely shall be available. Arm should be adaptable to hold up to 4 monitors.

1.9.2 Accessory boards or rails shall match panel sizes.

1.9.3 Paper management devices shall be available with horizontal, vertical, and diagonal configurations for desk top and panel mounted applications. Paper management shall include a slanted file-holder pencil cup, in/out box, and phone tray.

1.10 GROUP 1 – PERSONAL STORAGE UNIT SPECIFICATIONS

1.10.1 Personal storage towers shall be available. Refer to typical drawings for dimensions.

1.10.2 Personal storage tower finish to be available in wood veneer to match work surface and plastic laminate or metal to match other systems finishes. Storage units shall have capacity to house coats, personal items and files. Drawers on personal storage tower shall have extra heavy duty ball bearing suspension. File drawers shall have full extension. Storage should be lockable. See work key plan under services for requirements on locks and cores.

1.10.3 The following storage configurations shall be part of the product offering:

Flipper door.

Open shelf.

Lateral file drawers.

Box drawers.

Hinged cabinet doors.

Personal Storage Tower.

Bookcases

1.10.4 Mobile pedestal shall be available with cushion tops; one box drawer and one file drawer.

1.10.5 All storage unit components, including but not limited to bookshelves, wardrobes, lateral files, pedestals, etc. shall be available in painted metal and laminate finishes.

1.11 GROUP 1 – TEAMING AREA SPECIFICATIONS

1.11.1 Product line shall offer integrated freestanding storage cabinets and work surface. Finishes shall include laminate and veneer surfaces.

1.11.2 Tackboards and markerboards either panel mounted or integrated into the panel system shall be available.

1.11.3 Wall mounted and demountable partition tackboards and markerboards shall be available. All mounting hardware shall be included.

1.11.4 Freestanding mobile privacy screens shall be available.

1.12 GROUP 1 – FREESTANDING LATERAL FILING SPECIFICATIONS

1.12.1 Freestanding lateral files shall be offered. File cabinets shall accommodate letter and/or legal filing capabilities as a standard from the factory. All necessary hanging rails shall be included as part of the original installation. No additional parts/rails shall be necessary to switch from letter or legal size.

1.12.2 Wood veneer, laminate, and painted metal finishes shall be available to match pedestals.

1.12.3 File cabinets shall have four adjustable leveling glides. Pulls shall be provided on units with flush steel front. Units shall be weighted with a counterweight.

1.12.4 Four drawer unit shall be configured with three (3) 12” high drawers and one (1) 13-1/2” lift-up door with fixed shelf and shall be 18” to 20” deep.

1.12.5 Two and Three drawer units shall be configured with Two (2) or Three (3) 12” high drawers and shall be 18” to 20” deep.

1.13 GROUP 1– 24/7 WORK CONSOLE STATIONS

1.13.1 Curved console, capable of connecting numerous pieces in a unique formation of elongated half-rings, each console to house up to 3 CPUs.

1.13.2 Consoles shall be made of at least 1 inch particle board covered with laminate or cold rolled steel.

1.13.3 Laminate work surface edges shall be post-formed in a single sheet of material that wraps the front edge and continues under the work surface, creating a clean protective edge.

1.13.4 The console shall include 120 volt, 20 amp electrical power source.

1.13.5 Grommets for cable management are required.

1.13.6 Ventilation grills shall be placed where generated heat can easily leave the console enclosure.

1.13.7 Hinged or removable lower panels shall provide access to internally mounted equipment for service.

1.14 GROUP 1 – BENCHING SYSTEMS FURNITURE SPECIFICATIONS

1.14.1 Work surface lengths shall be available in 48”, 60” and 72”. Work surface depth shall be 30”.

Work surface finish shall be available in durable laminate and wood as standard finishes.

1.14.2 Benches shall have monitor racks on back panel to support two (2) monitors. Power and data requirements shall be as specified in paragraph 1.2.

Reference #: 1

Item: Keyboard

Description: Articulating and ergonomic

Dimensions: 22"D x 28"W x 8"H

Finishes: n/a

Image: Image for reference only.

Reference #: 2

Item: Lateral File

Description: 4H drawer, top shelf to have flipper door; metal construction, fireproof

Dimensions: 22"D x 31"W x 54"H maximum

Finishes: Powder coated metal finish

Image: n/a

Reference #: 3

Item: Monitor Arm

Description: Available in grommet and clamp; ability to hold 2 monitors

Dimensions: n/a

Reference #: 4

Item: Printer Bench

Description: 2H Lateral file with a HPL worksurface

Dimensions: 36" wide lateral file; 36"W x 24"D Laminate top

Finishes: Powder coated metal finish, High pressure laminate surface

Reference #: 5

Item: Reception Workstation

Description: 96 linear inches of work surface, transaction counter, 72 linear inches of storage space, one (1) wardrobe/storage unit anchored to end, paper management, tackable surface on interior panels b/w overhead storage and worksurface, panel mounted whiteboard with tackable strip, 2 drawer under worksurface metal file, 2 high undercounter metal bookcase, one (1) box/file metal mobile pedestal w/ cushion top, powered acoustic panels, painted trim

Dimensions: (56 SF) approx. 90"D x 90"W; transaction top 12"D and to span length of main worksurface, height to be 42"H AFF

Finishes: Workstation framing to be powder coated metal finish; pedestal cushion to be highest grade woven fabric; acoustic panels and tackable panel to be mid-grade fabric

Reference #: 6

Item: Task Light

Description: Freestanding, energy saving, articulating, NOT to be incandescent

Dimensions: 9"D x 9"W x 14"H

Reference #: 7

Item: Power Whip

Description: 8-wire, 3-circuit system

Dimensions: Min 10 feet long

Reference #: 8

Item: 24/7 Work Console Station

Description: Curve design, capable of connecting numerous pieces in a unique formation of elongated half-rings (would require field measurements & site verification), panel for up to four

(4) monitor arms, for use in 24/7 Mission Critical Areas, similar to Evans Consoles company models

Dimensions: 36"D x 42"W min.

Finishes: Laminate work surface, powder coated metal construction

Reference #: 9

Item: Workstation

Description: 96 linear inches of work surface w/ pencil drawer, 96 linear inches of storage space, one (1) wardrobe/storage unit anchored to end, paper management, tackable surface on interior panels b/w overhead storage and worksurface, panel mounted whiteboard with tackable strip, 2 drawer under worksurface metal file, 2 high undercounter metal bookcase, one (1) box/file metal mobile pedestal w/ cushion top, powered acoustic panels, painted trim

Dimensions: (84 SF) approx. 90"D x 130"W

Finishes: Workstation framing to be powder coated metal finish; pedestal cushion to be

Reference #: 10

Description: 96 linear inches of work surface w/ pencil drawer, 72 linear inches of storage space, one (1) wardrobe/storage unit anchored to end, paper management, tackable surface on interior panels b/w overhead storage and worksurface, panel mounted whiteboard with tackable strip, 2 drawer under worksurface metal file, 2 high undercounter metal bookcase, one (1) box/file metal mobile pedestal w/ cushion top, powered acoustic panels, painted trim

Dimensions: (56 SF) approx. 90"D x 90"W

Finishes: Workstation framing to be powder coated metal finish; pedestal cushion to be

Reference #: 11

Description: 90 linear inches of work surface w/ pencil drawer, paper management, tackable surface on interior panels b/w overhead storage and worksurface, panel mounted whiteboard with tackable strip, one (1) box/file metal mobile pedestal w/ cushion top, powered acoustic panels, painted trim

Dimensions: approx. 60"D x 60"W

Finishes: Workstation framing to be powder coated metal finish; pedestal cushion to be

Reference #: 12

Description: 56 SF open office typical: 96 linear inches of work surface w/ pencil drawer, 72 linear inches of storage space, one (1) wardrobe/storage unit anchored to end, paper management, tackable surface on interior panels b/w overhead storage and worksurface, panel mounted whiteboard with tackable strip, 2 drawer under worksurface metal file, 2 high undercounter metal bookcase, one (1) box/file metal mobile pedestal w/ cushion top, powered acoustic panels, painted trim

Dimensions: 56 SF

Finishes: Workstation framing to be powder coated metal finish; pedestal cushion to be

Reference #: 13 linear inches of storage space, one (1) wardrobe/storage unit anchored to end, paper management, tackable surface on interior panels b/w overhead storage and worksurface, panel mounted whiteboard with tackable strip, 2 drawer under worksurface metal file, 2 high undercounter metal bookcase, one (1) box/file metal mobile pedestal w/ cushion top, powered acoustic panels, painted trim

Dimensions: 56 SF

Finishes: Workstation framing to be powder coated metal finish; pedestal cushion to be

Reference #: 14 linear inches of storage space, one (1) wardrobe/storage unit anchored to end, paper management, tackable surface on interior panels b/w overhead storage and worksurface, panel mounted whiteboard with tackable strip, 2 drawer under worksurface metal file, 2 high undercounter metal bookcase, one (1) box/file metal mobile pedestal w/ cushion top, powered acoustic panels, painted trim

Dimensions: 56 SF

Finishes: Workstation framing to be powder coated metal finish; pedestal cushion to be

Reference #: 15 linear inches of storage space, one (1) wardrobe/storage unit anchored to end, paper management, tackable surface on interior panels b/w overhead storage and worksurface, panel mounted whiteboard with tackable strip, 2 drawer under worksurface metal file, 2 high undercounter metal bookcase, one (1) box/file metal mobile pedestal w/ cushion top, powered acoustic panels, painted trim

Dimensions: 56 SF

Finishes: Workstation framing to be powder coated metal finish; pedestal cushion to be

Reference #: 16

Item: Privacy Screen

Description: Panel mounted privacy screen

Dimensions: 12-18" high

Finishes: Mid-grade fabric panels to match finishes for open office workstation

Reference #: 17

Item: Storage Tower

Description: Personal storage tower with wardrobe, 2 file drawers, and storage cabinet

Dimensions: 20"D x 20"W x 54"H

Finishes: To match open office workstation materials

Reference #: 18

Item: Adjustable Height Worksurface

Description: Adjustable height worksurface, pnuematic operating

Dimensions: Main worksurface to be 24"D x 7'-0"W

Finishes: To match open office workstation materials

Reference #: 19

Item: Mobile Screen

Description: Freestanding, whiteboard including magnetic caddy with erasers and market sets

Dimensions: 54"H x 36"W

Finishes: Metal construction

Reference #: 20

Item: Spline Panel

Description: IT and powered spline panels at open office workstation; acoustical fabric panels and hard surface panels

Dimensions: 42"W x 54"H

Finishes: Highest grade woven fabric

Reference #: 21 and hard surface panels

Dimensions: 30"W x 54"H

Reference #: 22 and hard surface panels

Dimensions: 36"W x 54"H

Reference #: 23 and hard surface panels

Dimensions: 24"W x 54"H

Reference #: 24 and hard surface panels

Dimensions: 18"W x 54"H

2.0

GROUP 2

CASEGOODS AND CONFERENCE ROOMS

2.0 GROUP 2 – CASEGOOD AND CONFERENCE ROOM FURNITURE

SPECIFICATIONS

2.1 GROUP 2 – PRIVATE OFFICE CASEGOODS & CONFERENCE SPECIFICATIONS

2.1.1 All work surfaces with unsupported knee spaces of 60” or greater in length shall be steel reinforced. Wires shall be managed through a cable management system tight under the work surface so as to be not visible. Wire management access and receptacles shall be provided at the desktop in devices integrated with the casegoods design. Work surface shall have two grommets. Casegood work surfaces to have capability of accepting articulating keyboard tray.

2.1.2 Finishes shall include wood veneers, wood solids, and laminate.

2.1.3 Single pedestal desk shall be available with full height/full depth lockable Box/Box/File pedestal, full modesty panel, wire management, center drawer, and two grommets.

2.1.4 Work surfaces shall be available in wood and laminate finishes in rectangular, curved, bullet, transaction, and corner configurations. Laminate work surface edges shall be post-formed in a single sheet of material that wraps the front edge and continues under the work surface, creating a clean protective edge. Adjustable height work surfaces shall be available. The method of adjustment shall be pneumatic height adjusted.

2.1.5 Credenza shall be available. Cable access shall be in the back panel. There shall be a lockable full height/full depth box/box/file pedestal and an under counter 36” 2 drawer lateral file.

2.1.6 Overhead unit shall be available with hinged doors with pulls. Cabinet height above worksurface shall be 25” +/- 3” with cable access in the back panel. Acoustical and tackable panels shall be available.

2.1.7 Units shall be available as a mobile, lockable pedestal with upholstered cushion top and lockable casters. Finish shall be wood veneer on all sides.

2.1.8 Mobile, fixed and freestanding storage shall be available with full height/full depth box/file, box/box/file, and file/file configurations.

2.2.1 GROUP 2 – CONFERENCE TABLE SPECIFICATIONS

2.2.2 Table shall be a rectangular top with panel type power/data access base.

2.2.3 A modesty panel shall be provided to hold power/data/AV raceways.

2.2.4 Construction shall be either 3-ply balanced wood veneer surfaces with self edge or laminate with PVC self edge.

2.2.5 Base shall allow access to power and data cables.

2.2.6 (VTC Large Conference Room seating 20-40 people)

Table shall be a rectangular top. Construction shall be 3-ply balanced wood veneer surfaces with hardwood. Bases shall be panel type allowing access to power/data cables and finishes shall be available in wood and metal.

2.2.7 (VTC Medium Conference Room seating 12-16 people)

Table shall be transitional style, reconfigurable to rectangular or V-shaped configuration with a wood or laminate top. Laminate surface shall have a PVC edge. Bases shall be panel type allowing access to power/data cables and finishes shall be available in wood and metal.

2.2.8 (Small Conference Table seating 8 people)

Table shall be a rectangular top laminate surface with PVC edge. Bases shall be panel type allowing access to power/data cables and finishes shall be available in wood and metal.

2.3 GROUP 2 – CONFERENCE ROOM TABLES INFORMATION TECHNOLOGY (IT),

AUDIO-VISUAL (AV), AND POWER SPECIFICATIONS

The Furniture Contractor shall provide conference tables that meet the following IT, A/V, and power requirements.

2.3.1 Conference Table Raceway Requirements: For tables requiring ganging outlets or pop-up terminations the furniture contractor shall provide (2) separate IT, (1) AV and (1) power raceway system. For the raceway system, the furniture contractor shall provide a minimum of two (2) physically separated IT raceways with a two (2”) inch separation or more between them.

2.3.2 The A/V raceway needs to be separate and have the two (2”) separations between the IT raceways. It is preferred that each IT raceway has a 3-sided enclosure for cable lay-in capability; however, other raceway designs that provide cable management which is held tight to the underside of the work surface and maintains all required separation shall be acceptable.

2.3.3 All raceways shall be sized to accommodate the following IT and A/V distribution at each seated position at a 40% fill with the ability for expansion.

a. A/V Distribution requirements for each seated position:

1. One (1) SVGA cables for PC video (11 mm dia). Provide option for HDMI pathway.

2. Two (2) 1/8” mini-stereo audio cables for PC audio (7 mm dia each)

b. Power Distribution for each seated position:

1. One (1) power cables for PC power (8 mm dia each).

2.3.4 All boxes required for pop-up or table top devices shall be provided by the furniture supplier.

2.4 GROUP 2 – BOOKCASE SPECIFICATIONS

Bookcases shall be available as freestanding units.

2.5 GROUP 2 – FLOOR LECTERN SPECIFICATIONS

2.5.1 Lecterns shall be provided with one locking and one non-locking lower compartment for AV equipment and general storage. Lectern shall have an adjustable shelf behind hinged doors.

Presentation surface and chassis shall be laminate. The lectern shall have grommets throughout the unit to allow for power/data access to the floor for cable management. Cable management shall be internal to the unit. Unit shall have four locking dual-wheel casters.

2.6 GROUP 2 – FREESTANDING LATERAL FILING SPECIFICATIONS

2.6.1 Freestanding lateral files shall be offered as part of the casegoods product line. File cabinets shall accommodate letter and/or legal filing capabilities. All necessary hanging rails shall be included as part of the original installation. No additional parts/rails shall be necessary to switch from letter or legal size.

2.6.2 Wood veneer and laminate finishes shall be available to match pedestals. File cabinets shall have four adjustable leveling glides. Units shall be weighted with a counterweight.

Reference #: 25

Item: Bookcase

Description: 4 shelves high

Dimensions: 14"D x 36"W x 70"H

Finishes: Wood veneer

Reference #: 26

Item: Bookcase

Description: Under-worksurface bookcase 2 shelves high

Dimensions: 14"D x 36"W x 26"H

Finishes: Wood veneer

Reference #: 27

Item: Conference Table

Description: Reconfigurable table, power/data accessible from top, provide linking devices and wire management, seats thirty (30)

Dimensions: assumption for each table to be 6'L x 3'W

Finishes: Wood

Reference #: 28 wire management, seats twelve (12)

Dimensions: assumption for individual pieces to be 6'L x 3'W

Reference #: 29 wire management, seats eight (8)

Dimensions: assumption for all individual pieces to be 4'L x 3'W

Reference #: 30

Description: U-shaped, reconfigurable table, power/data accessible from top, provide linking devices and wire management, seats fourteen (14)

Dimensions: assumption for individual pieces to be 6'L x 3'W

Reference #: 31

Description: V-configured, wood, reconfigurable table, power/data accessible from top, provide linking devices and wire management, seats sixteen (16)

Dimensions: assumption for individual pieces to be 6'L x 3'W

Reference #: 32

Description: V-configured, reconfigurable table, power/data accessible from top, provide linking devices and wire management, seats fourteen (14)

Dimensions: assumption for individual pieces to be 4'L x 3'W

Reference #: 33

Description: Nesting table

Dimensions: assumption for individual pieces to be 6'L x 3'W

Finishes:

Reference #: 34

Item: Credenza

Description: Hinged doors and adjustable shelves

Dimensions: 60"W x 20"D x 29"H

Finishes: Wood, stainless steel pulls

Reference #: 35

Description: Hinged doors and adjustable shelves; style and finish to match coordinating conference room table

Dimensions:

Finishes: Wood laminate

Reference #: 36

Description: Hinged doors and adjustable shelves; style and finish to match coordinating conference room table

Dimensions:

Reference #: 37

Item: Desk

Description: Connected desk w/ pencil drawer, return and credenza unit - or U-shaped desk -two (2) pedestals, 96" linear overhead storage w/ wall mounted tackable surface b/w overhead storage and worksurface, one (1) wardrobe anchored on end, including wall mounted white board with tackable strip, paper management, and 4-5 drawer lateral file (all pieces to be panel hung optional)

Dimensions: approx. 120"D x 96W"

Finishes: All components to be wood veneer; tackable surface and cushion pedestal top to be highest grade woven fabric.

Reference #: 38

Description: Mobile peninsula desk unit w/ pencil drawer, connected return and credenza unit -or L-shaped desk - w/ 96" linear overhead storage, wall mounted tackable surface between overhead storage and worksurface, one (1) wardrobe/storage cabinet anchored to end, wall mounted white board with tackable strip, 2-drawer lateral file, paper management, and undercounter mobile box/file pedestal w/ cushion top ( all pieces to be panel hung optional)

Dimensions: approx. 168"D x 96"W

Finishes: All worksurfaces to be wood veneer; metal files and legs to be powder coated;

tackable surface and cushion pedestal top to be highest grade woven fabric.

Reference #: 39

Description: Mobile peninsula desk unit w/ pencil drawer, connected return and credenza unit -or L-shaped desk - w/ 96" linear wood veneer overhead storage, wall mounted tackable surface between overhead storage and worksurface, one (1) wardrobe/storage cabinet anchored to end, wall mounted white board with tackable strip, 4-5 drawer lateral file, paper management, and undercounter mobile box/file pedestal w/ cushion top (all pieces to be panel hung optional)

Dimensions: approx. 120"D x 96"W

Finishes: All worksurfaces to be wood veneer; metal files and legs to be powder coated;

tackable surface and cushion pedestal top to be highest grade woven fabric.

Reference #: 40

Item: Meeting Table

Description: Oval table to seat six (6); X-base

Dimensions: 72"L x 44"W x 28"H

Finishes: Wood veneer, powder coated base

Reference #: 41

Item: Meeting Table

Description: Seats four (4); X-base

Dimensions: 36"D x 60"W

Finishes: Wood veneer; powder coated base

3.0

GROUP 3

SEATING

3.0 GROUP 3 – SEATING SPECIFICATIONS

3.1 GROUP 3 – TASK SEATING SPECIFICATIONS

3.1.1 The depth of the seat pan shall be between 16-20 inches.

3.1.2 The chair shall offer a pneumatic seat height adjustment with an adjustment range of at least four (4) inches.

3.1.3 Both sides of the chair back shall be covered in mesh or fabric upholstery with at the highest graded-in woven textile pricing.

3.1.4 The chair shall offer an independent adjustable lumbar and upper back support. Both armless and fixed task arms shall be available.

3.1.5 The fixed arm shall be adjustable and shall offer a vertical height adjustment range of at least

4 inches and a pivot adjustment including an inward and outward motion.

3.1.6 The base of the chair shall be made of metal.

3.1.7 Chair seat shall include a waterfall construction.

3.1.8 Labels and/or user guides, for adjustment mechanisms, shall be attached to the chair.

3.1.9 Chair base shall have hard casters for carpet.

3.2 GROUP 3 – EXECUTIVE CONFERENCE SEATING SPECIFICATIONS

3.2.1 The depth of the seat pan shall be between 16-20 inches.

3.2.2 The chair shall offer a pneumatic seat height adjustment with an adjustment range of at least four (4) inches.

3.2.3 The chair shall offer tilt swivel with knee tilt.

3.2.4 The chair shall offer a passive ergonomic lumbar support.

3.2.5 The chair shall be high-back height and fully upholstered.

3.2.6 The chair shall offer fully upholstered arms.

3.2.7 The base of the chair shall be made metal.

3.2.8 Chair shall be offered in both the highest graded-in woven upholstery textile and highest graded-in leather.

3.2.9 The chair shall have adjustable arms that offer a vertical height adjustable range of 4” and a pivot adjustment inward and outward.

3.2.10 Chair seat shall include a waterfall construction.

3.2.11 Labels and/or user guides, for adjustment mechanisms, shall be attached to the chair.

3.2.12 Chair base shall have hard casters for carpet.

3.3 GROUP 3 – PRIVATE OFFICE GUEST SEATING SPECIFICATIONS

3.3.1 The chair to be constructed with a double-doweled hardwood frame.

3.3.2 The chair shall offer an upholstered seat.

3.3.3 The chair shall be offered in both the highest graded-in woven upholstery textile and highest graded-in leather.

3.3.4 The chair shall be offered with a wood back and an upholstered back.

3.4 GROUP 3 – BREAKROOM/CAFETERIA SEATING SPECIFICATIONS

3.4.1 The depth of the seat pan shall be between 16-20 inches.

3.4.2 The chair shall be offered with and without arms.

3.4.3 Chair shall have a metal frame construction.

3.4.4 Chair shall have a molded polypropylene backrest and seat.

3.4.5 The chair shall be capable of being stacked. A stacking chair shall be capable of stacking at least 10 high.

3.4.6 The base of the chair shall be made of metal.

3.4.7 Dollie shall be available and capable of stacking at least 10 chairs and have casters.

3.5 GROUP 3 – TRAINING ROOM SEATING SPECIFICATIONS

3.5.1 The depth of the seat pan shall be between 16-20 inches.

3.5.2 Chairs shall have arms and shall have a metal frame construction.

3.5.3 The chair shall be offered in a molded polypropylene and upholstered backrest.

3.5.4 Chair shall have an upholstered seat.

3.5.5 The chair shall be capable of being stacked. A stacking chair shall be capable of stacking at least 10 or more high.

3.5.6 Chair shall have highest graded-in woven upholstery textile.

3.5.7 Base shall be made of metal.

3.5.8 Dollie shall be available and capable of stacking at least 10 chairs and have casters.

Reference #: 42

Item: Adjustable Height Worksurface

Description: Adjustable height worksurface (pneumatic height)

Dimensions: 168"D x 96"W

Finishes: To be available in finishes to match private office or workstation

Reference #: 43

Item: Chair Dollie

Description: Three wheels, metal, support up to 10 chairs

Dimensions: 25"L x 25"W

Reference #: 44

Item: Conference Chair

Description: Adjustable, executive high-back chair with open arms, star-base with casters

Dimensions: 29"D x 27"W x 43"-48"H

Finishes: Highest grade leather upholstry, aluminum base.

Reference #: 45

Item: Conference Chair

Description: Adjustable, executive medium-back chair with open arms and star-base with casters

Dimensions: 29"D x 27"W x 36"-48"H

Finishes: Highest grade leather upholstry, aluminum base.

Reference #: 46

Item: Executive Task Chair

Description: Adjustable high-back chair wtih open arms and star-base with casters

Dimensions: 29"D x 27"W x 36"-48"H

Finishes: Highest grade woven fabric, aluminum base; option for mesh or upholstered back

Reference #: 47

Item: Executive Task Chair

Description: Adjustable mid-back chair wtih open arms and star-base with casters

Dimensions: 29"D x 27"W x 36"-48"H

Reference #: 48

Item: Guest Chair

Description: Wood frame, mid-back with open arms

Dimensions: 23"D x 23"W x 34"H

Finishes: Highest grade woven fabric.

Reference #: 49

Item: Lunchroom Seating

Description: Hard surface monoshell; no arms; stackable; 4-post or sled base legs, tubular construction

Dimensions: 20"W x 22"D x 35"H

Finishes: Wood veneer finish, polished legs

Reference #: 50

Item: Lunchroom Seating

Description: Durable plastic surface with sled base, no arms, stackable

Dimensions: 21"W x 36"D x 19"H

Finishes: Wire rod frame, thermoplastic monoshell

Reference #: 51

Item: Side Chair

Description: hard surface, no arms

Dimensions:

Reference #: 52

Description: hard surface, no arms, stackable

Dimensions:

Reference #: 53

Description: Attenuating back w/ sled base; stackable

Dimensions: 22"W x 23"D x 32.5"H

Finishes: Thermoplastic seat and back, option for seat and back cushion; polished base

Reference #: 54

Item: Task Chair

Description: Adjustable mid-back chair w/ open arms, casters, durable fabric

Dimensions: 29"D x 27"W x 36" - 48"H

Reference #: 55

Description: Adjustable mid-back chair w/ open arms, casters, durable fabric

Dimensions: 29"D x 27"W x 36"-48"H

Reference #: 56

Description: Mid-back, movable, data and power capable

Dimensions: 29"D x 27"W x 36"-48"H

Image:

Reference #: 57

Description: Adjustable mid-back chair w/ open arms, casters, durable mesh fabric

Dimensions: 29"D x 27"W x 36"-45"H

Reference #: 58

Description: High adjustable mid-back chair w/ open arms, casters

Dimensions: 29"D x 27"W x 36"-48"H

Finishes: Mesh back and seat, plastic base

Reference #: 59

Item: Task Stool

Description: Adjustable mid-back w/ arms, casters

Dimensions: 29"D x 27"W x 44"-53"H

Finishes: Mesh back and seat, plastic base

Reference #: 60

Item: Training Chair

Description: Attenuating back, sled base; stackable

Dimensions: 22"W x 23"D x 32.5"H

Finishes: Thermoplastic seat and back, option for seat and back cushion; polished base

SECTION 4.0: GROUP 4

STORAGE

Reference #: 61

GROUP 4

Item: Legal Safe-in-a-file

Description: 4-drawer fireproof, GSA approved security container

Dimensions: 31"D x 20"W x no more than 54"H

Reference #: 62

Item: Legal Safe-in-a-file

Description: 2-drawer, fireproof, GSA approved security container

Dimensions: 31"D x 20"W x no more than 28"H

Reference #: 63

Description: 4-drawer, fireproof

Dimensions: 22"D x 31"W x 36-48"H

Reference #: 64

Description: 5-drawer high

Dimensions: 18"D x 36"W

Reference #: 65

Item: Storage Cabinet

Description: 5-shelf high

Dimensions: 18"D x 36"W

Reference #: 66

Description: 5 -drawer (top receding door)

Dimensions: 18"D x 36"W

Reference #: 67

Item: Warehouse racks and cages

Description: Racks and cages suitable for warehouse storage

Dimensions: n/a

5.0

GROUP 5

ANCILLARY FURNITURE

5.0 GROUP 5 – ANCILLARY FURNITURE SPECIFICATIONS

5.1 GROUP 5 – TV/VCR CABINET SPECIFICATIONS

5.1.1 Cabinet shall be 77”H (+/- 3”) cabinet and shall accommodate a 37” Flat screen monitor, articulation monitor arm, CPU, DVD player, and VCR all housed in one unit. The unit shall include a 20 amp power strip with a minimum of four electrical outlets, with (6) foot or longer power cord. The cabinet shall have a means for ventilation.

5.2 GROUP 5 – BREAKROOM TABLE SPECIFICATIONS

5.2.1 Table shall have a round top, 1 3/16” minimum thick with a high pressure laminate surface.

Laminate surfaces shall have a PVC edge. Table shall have a tubular steel pedestal base with leveling guides.

5.3 GROUP 5 – TRAINING ROOM TABLE SPECIFICATIONS

5.3.1 Table shall have a rectangular top with a high pressure laminate surface. Laminate surface shall be offered in a PVC edge and wood edge. Table base shall be tubular steel or aluminum mobile base with dual wheel locking casters. Table shall have nesting capability. Table shall be provided with a modesty panel that does not have to be removed to accommodate nesting condition.

5.3.2 The table shall be computer capable with data and power connectivity to be coordinated with the IT integrator. Cable management shall be through the table legs.

5.4 GROUP 5 – MAIN STREET AND PREFUNCTION AREA BENCH SEATING

5.4.1 Bench seating shall be available in both two and three seat widths. Seating shall be fully upholstered faux leather with fixed leg construction. Wood frame and leg finishes shall be available in either metal or wood.

5.5 GROUP 5 –LOUNGE CHAIR SEATING

5.5.1 Seating shall be available in single, double, and triple seat width and shall have no taller than a 32”H back. Seating shall have wood frame, legs and arms. Seating shall be available in the highest graded-in woven upholstery textile and highest graded-in leather seats and backs.

5.6 GROUP 5 –LOUNGE TRAINING CHAIR SEATING

5.6.1 Upholstered lounge chair with fold out tablet table. Seat and back shall be available in the highest graded-in woven upholstery textile.

5.7 GROUP 5 – CAFETERIA BOOTH SEATING

5.7.1 Seating shall be available in both single and double units with 36”H. back. Seating shall have hardwood frames with reinforced joints. Seating shall have the highest graded-in vinyl upholstered textile seat, back and wrapped edges. Seating shall have removable top caps and end panels for easy repair.

5.8 GROUP 5 – CORP CENTER AV VIDEO EDITING WORK STATION SPECIFICATIONS

5.8.1 Overall dimensions shall be 9’w x 2 ’-6”d, +/- 3”, by 3’– 0” h. Station shall be capable of supporting standard 19” rack mountable equipment. Cable management with three (3) each

3” grommets shall be provided.

5.8.2 Work surface constructed shall be 1-1/8” particle board core, laminate. Rack cabinet frames shall have a textured powder coated enamel finish. Rack Cabinet’s Side panel and legs shall be powder coated enamel finish.

Reference #: 68

Item: Coffee Table

Description: Round coffee table, transitional style

Dimensions: 42" dia.

Reference #: 69

Description: Rectangular, transitional style

Dimensions: 48"W x 24"D

Reference #: 70

Description: Rectangular, transitional style, metal legs

Dimensions: 72"W x 36"D

Finishes: Wood surface, polished or satin legs

Reference #: 71

Item: Conferencing Team Table

Description: Laminate top, power/data accessible from top, provide linking devices and wire management, seats six (6)

Dimensions: 36"D x 108"W

Finishes: Laminate worksurface, powder coated metal lateral file base?????

Reference #: 72

Item: Tablet Arm Chair

Description: Tablet arm chair with casters, fully upholstered

Dimensions: 29.5"L x 29"W

Finishes: Highest grade vinyl or woven fabric available; wood veneer tablet surface

Reference #: 73

Item: File Cart

Description: Mobile file cart on wheels with shelf below

Dimensions: 18"W x 36"L

Finishes: Plastic laminate????

Reference #: 74

Item: Display Case

Description: Tall glass display case, elliptical or thin profile

Dimensions: 42"W x 9"D x 72"H

Finishes: Anodized aluminum framing, tempered glass with polished edges

Reference #: 75

Description: Short glass display case, square on pedestal

Dimensions: 24" x 24"

Reference #: 76

Description: Glass display case, rectangular

Dimensions: 42"W x 42"H x 24"D

Reference #: 77

Description: Mobile screen with upholstered, tackable surface.

Dimensions: 40"W x 64"H

Finishes: Mid-grade tackable fabric

Reference #: 78

Description: Mobile screen with upholstered, tackable surface.

Dimensions: 60"W x 64"H

Finishes: Mid-grade tackable fabric

Reference #: 79

Description: Markerboard smart screen on casters with magnetic tray, eraser and markers

Dimensions: 48"W x 72"H

Reference #: 80

Item: Large transaction top reception counter

Description: Custom built

Dimensions:

Reference #: 81

Item: Sofa

Description: Transitional style, high quality soft seating, open wood arms

Dimensions: 30"D x 60"W

Finishes: Highest grade leather

Reference #: 82

Item: Lounge Chair

Description: Transitional style, high quality soft seating, open wood arms

Dimensions: 30"D x 30"W

Finishes: Highest grade leather

Reference #: 83

Item: Maintenance work bench

Description: Adjustable work surface, steel channel legs, knockouts for power access, durable work surface

Dimensions: 72"W x 30"D

Finishes: Steel construction, high pressure laminate worksurface

Reference #: 84

Item: Magazine Racks

Description: Single column magazine holder with 9-12 pockets

Dimensions: 30"W x 36 3/4"H

Finishes: Clear plastic

Reference #: 85

Item: Outdoor Seating

Description: All-Weather Resistant Treated Wood Plastic Composite dining chair, no arms

Dimensions: 17"W x 17 3/4" seat height

Finishes: Wood plastic composite

Reference #: 86

Item: Outdoor Bench Seating

Description: Bench-like, All-Weather Resistant Treated Wood, backless

Dimensions: 30"W x 11" D x 18"H

Reference #: 87

Item: Outdoor Trash Bin

Description: 32 gallon trash bin; durable, long-lasting flat bar-steel construction; durable plastic liner; leveling feet, anchor kit, and lid options available

Dimensions: 32 gallon

Finishes: Powder coated paint finish for outdoor use

Reference #: 88

Item: Round/ Rectangular Outdoor Table

Description: All-Weather Resistant Treated Wood-Plastic composite dining table

Dimensions: 48" Round/60"L x 36"W

Reference #: 89

Item: Side Lamp

Description: Table lamp with shade

Dimensions: n/a

Finishes: Metal, wood, or powder coated base, shade provided

Reference #: 90

Item: Side Lamp

Description: Side lamp to match custom office furniture, with shade provided

Dimensions: 24" sq

Finishes: Wood stain, fabric or paper shade option

Reference #: 91

Description: high quality soft seating for up to two (2) 1/ power and data, leather upholstery

Dimensions:

Reference #: 92

Description: high quality soft seating for up to eight (8) people w/ power and data, leather upholstery

Dimensions:

Reference #: 93

Description: high quality soft seating for up to four (4) people w/ power and data, leather upholstery

Dimensions:

Reference #: 94

Item: Table

Description: Round surface, x-base

Dimensions: 42" round x 28"H

Finishes: High pressure laminate or veneer surface, polished or powder coated base

Reference #: 95

Item: Table

Description: Mobile table to seat minimum of four (4) people, nesting w/ lockable casters

Dimensions: 60"L x 30"W

Finishes: Laminate surface, durabe tubular legs

Reference #: 96

Item: Work Table

Description: Laminate top

Dimensions: 30"D x 60"W

Reference #: 97

Item: Training Table

Description: Computer capable w/ one data/electric port on top, provide linking devices and wire management, nesting with lockable casters

Dimensions: 24"D x 60"W x 28"H

Reference #: 98

Item: Training Table

Description: Computer capable with one data/electric port on top, provide linking devices and wire management

Dimensions: 24"D x 30"W x 28"H

Finishes: Laminate surface

Reference #: 99

Item: video editing console

Description: video editing consiole desk, cable management, rack cabinet for equipment

Dimensions:

Reference #: 100

Item: TV/VCR cart

Description: Cart with shelf for VCR/DVD storage and capability to fit 40" TV, on casters

Dimensions: 30"W x 30"D

Finishes: Metal, powder cooated finish

Reference #: 101

Item: Recycle Bin

Description: Plastic, 28 Qt.

Dimensions: 14 3/8" x 10 1/4" x 15" H

Finishes: Plastic

Reference #: 102

Item: Recycle Bin

Description: Plastic

Dimensions: 32-42 gallon

Reference #: 103

Item: Waste Bin

Description: Plastic, 28 Qt.

Dimensions: 14 3/8" x 10 1/4" x 15" H

Reference #: 104

Item: Waste Bin

Description: Plastic

Dimensions: 32-42 gallon

Reference #: 105

Item: Whiteboard (48x60)

Description: Wallmounted whiteboard

Dimensions: 48"x60"

Finishes: Aluminum frame

Reference #: 106

Item: Hanger

Description: Wood hanger to fit in private office wardrobe; Quantity (2) per office

Dimensions: n/a

Finishes: Wood, black finish

Reference #: 107

Item: Hanger

Description: Metal hanger to fit in workstation wardrobe, Quantity (2) per workstation

Dimensions: n/a

Finishes: Black rubberized vinyl coating

Reference #: 108

Item: Coat Rack

Description: Mobile coat rack

Dimensions: Approximatley 4' W

Reference #: 109

Item: Low teaming area two seat lounge

Description: (2 required for standard layout) Grade B fabric sofa seating 2

Dimensions: Overall 7'-9" x 14'-3"

Reference #: 110

Item: Low teaming area three seat lounge

Description: Grade B fabric sofa seating 3

Dimensions: Overall 7'-9" x 14'-3"

Reference #: 111

Item: Low teaming area corner table

Description: (2 required for standard layout) Veneer top

Dimensions: Overall 7'-9" x 14'-3"

Reference #: 112

Item: Low teaming area console table

Description: (2 required for standard layout) Veneer top surface with undercut Bevel Stain and

Frosted Modesty Panel

Dimensions: Overall 7'-9" x 14'-3"

Reference #: 113

Item: Low teaming area table base

Description: (2 required for standard layout) Square table X base

Dimensions: 30"W x 30"D x 17"H ??????

Reference #: 114

Item: Low teaming area arm mount

Description: (2 required for standard layout) Square table X base

Dimensions: 16" mast

6.0

GROUP 6

HIGH DENSITY FILING

6.0 GROUP 6 - HIGH DENSITY FILING SPECIFICATIONS

6.1 GROUP 6 - LIBRARY BOOKSTACK SHELVING SPECIFICATIONS

6.1.1 Shelving shall be cantilever bracket type metal library bookstack as defined by the American

Library Association and published in their Library Technology Reports.

6.1.2 All fabricated metal components and Assemblies shall be painted with an…