FSV6-631-01_REV(B) Paint Schedule.pdf

SHEET

1A 1B 1C

3 GENERAL NOTES

3A GENERAL NOTES (Continued)

4 LIST OF MATERIALS

5 LIST OF COMPARTMENTS (Modules 101. 102. 103, 201) 5A LIST OF COMPARTMENTS (Modules 201, 202) 5B LIST OF COMPARTMENTS (Modules 202, 301, 302, 303, 401, 402, 403) 5C LIST OF COMPARTMENTS (Modules 403, 501, 502) 4 FSV6-635-01 5D LIST OF COMPARTMENTS (Modules 502, 503, 505, 507) 3 FSV6-602-01

6 PAINT SYSTEM "D-1" 2 FSV6-634-01

7 PAINT SYSTEM "D-2" 1 FSV6-601-01

8 PAINT SYSTEM "D-3" NO. MMC DRAWING NO.

9 PAINT SYSTEM "D-4"

10 PAINT SYSTEM "D-5"

11 PAINT SYSTEM "D-6"

12 PAINT SYSTEM "D-7"

12A PAINT SYSTEM "D-77A"

13 PAINT SYSTEM "D-8"

14 PAINT SYSTEM "E-1"

15 PAINT SYSTEM "E-2"

16 PAINT SYSTEM "E-3"

17 PAINT SYSTEM "E-4"

18 PAINT SYSTEM "I-1"

18A PAINT SYSTEM "I-1A"

19 PAINT SYSTEM "I-2"

20 PAINT SYSTEM "I-3"

20A PAINT SYSTEM "I-3A"

21 PAINT SYSTEM "I-4"

21A PAINT SYSTEM "I-4A"

22 PAINT SYSTEM "I-5"

23 PAINT SYSTEM "I-6" DATE:

24 PAINT SYSTEM "M-1"

25 PAINT SYSTEM "M-2" DATE:

26 PAINT SYSTEM "M-3" SH 1 OF 51

SHEET 1

APRV: C. JACKSON

Visual Identification & Draft Marks Insulation & Damping Tile A&D

PE STAMP:

DATE:

CONTRACT NO: AB133M10CN0091

FISHERIES SURVEY VESSEL 6

(FSV 6)

Deck Covering Schedule

REV

B

MARINETTE MARINE CORPORATION

MARINETTE WISCONSIN 54143

SCALE: NONE

PAINT SCHEDULE

FSCM CAGE NO

98042

INDEX

DESCRIPTION

TITLE, INDEX

PAINT SYSTEM LEGEND

PAINT SYSTEM LEGEND (Continued)

INDEX CONTINUDED

REVISIONS

General Arrangement, Inboard & Outboard Profiles

DRAWING NO.

FSV6-631-01

SIZE

A

NATIONAL OCEANIC &

ATMOSPHERIC ADMINISTRATION

(NOAA)

ABS APRV:

APRV: J. BRISKY

CHKD: T. ZMYSLO

DWN: J. K. EASTRIDGE

USCG APRV:

TITLE

REFERENCES

SHEET

27 PAINT SYSTEM "M-4"

28 PAINT SYSTEM "M-5"

28A PAINT SYSTEM "M-5A"

29 PAINT SYSTEM "M-6"

30 PAINT SYSTEM "M-7"

30A PAINT SYSTEM "M-7A"

31 PAINT SYSTEM "T-1"

32 PAINT SYSTEM "T-2"

33 PAINT SYSTEM "T-3"

34 PAINT SYSTEM "T-4"

35 PAINT SYSTEM "U-1"

36 PAINT SYSTEM "U-2"

DATE:

DATE:

SHEET 1A

INDEX

DESCRIPTION

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

0120-631-01

Decks

D-1 D-2 D-3 D-4 D-5 D-6 D-7 D-7A D-8

Exterior E-1

E-2 E-3

E-4

Interior I-1

I-1A

I-2 I-3 I-3A I-4 I-4A I-5 I-6

Misc.

M-1 M-2 M-3 M-4 M-5 M-5A M-6

M-7 Uninsulated areas that are in way of weather boundries. - ALKYD PRIMER

M-7A Uninsulated areas that are in way of weather boundries. - EPOXY PRIMER DATE:

DATE:

SHEET 1B

Machinery & foundations in machinery spaces above floor plates where temperature is less than 93 deg C. - EPOXY PRIMER

Aluminum deck surfaces requiring only primer in preparation for deck covering. - EPOXY PRIMER

Shell exterior (steel) from waterline up, including outboard side of bulwarks, exterior steel deckhouses, vents, overflows, overhead surfaces, deck gear lockers, doors, stanchions, vertical & inclined ladders, handrails, ventilators, bulwark-mounted chocks, davits, steel monorails

Exposed interior steel bulkheads & overheads in machinery spaces, service spaces, workshops, storerooms, deck lockers, interior railings, stanchions & associated fittings - EPOXY PRIMER

Interior steel ladders (excluding ladders in tanks) - EPOXY PRIMER

Unexposed steel structure behind insulation and/or joiner panels - EPOXY PRIMER

Machinery & foundations in machinery spaces above floor plates where temperature is less than 93 deg C. - ALYKD PRIMER

Bilges

Unexposed steel structure behind insulation and/or joiner panels - ALKYD PRIMER

Exterior exposed vertical aluminum surfaces including vents, overflows, deck gear lockers, doors, stanchions, vertical and inclined ladders, handrails, ventilators, stack (excluding special markings) & underside of exposed aluminum deckheads.

Steel masts, booms, gantries, A-frames and similar fittings and equipment

Interior steel ladders (excluding ladders in tanks) - ALKYD PRIMER Exposed interior aluminum bulkheads & overheads

Exposed interior steel bulkheads & overheads in machinery spaces, service spaces, workshops, storerooms, deck lockers, interior railings, stanchions & associated fittings - ALKYD PRIMER

Aluminum masts, booms, trusses and similar fittings & equipment

Exposed insulation IWO aluminum structure, but not type II acoustic insulation.

PAINT SYSTEM LEGEND

Steel deck surfaces requiring only primer in preparation for deck covering. - EPOXY PRIMER Steel deck surfaces requiring only primer in preparation for deck covering. - ALKYD PRIMER

SCALE: NONE

Exterior Steel decks, house tops, hatch covers & coamings, inboard side of bulwark.

Interior steel decks in AMR & service spaces, workshops, storerooms, deck lockers and similar spaces.

Exterior Aluminum decks, house tops, hatch covers & coamings, foundations & deck fittings.

Exposed interior Aluminum decks.

Misc. exterior steel deck fittings, deck-mounted machinery, chocks, cleats, bitts.

Walking surfaces of steel floor plates, grating, decks & platforms in main machinery spaces.

Anchor Anchor Chain Chain locker & sump Engine exhaust and other surfaces above 93 deg. C. (excluding lagged exhaust piping)

Inaccessible voids

Continued on Sheet 1C

REV

BABS APRV:

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

FSV6-631-01

Tanks T-1 T-2 T-3 T-4

Under Water U-1 U-2

DATE:

DATE:

SHEET 1C

REV

BABS APRV:

PAINT SYSTEM LEGEND (Continued)

Fuel oil, Lube oil, & dirty oil tanks (steel) Steel ballast tanks, sewage and gray water tanks, misc. tanks & voids, steel portion of the centerboard trunk, transducer tube Fresh & potable water tanks (steel) Aluminum tank and trunk interiors

SCALE: NONE

Note: Ladders inside tanks to receive same coating as tank interior)

Exterior underwater body including trunks and appendages, but excluding seachests Seachests

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

0120-631-01

SHT REV DATE APPROVED

ALL - 9/27/2010 T. ZMYSLO

5/16/2013 RRZ

7/23/2013 PWH

DATE:

DATE:

SHEET 2

5,5B,33

1,1A,1B,1C 3A,5,5B,5C

3A,8,9

5A

DRAWING REVISION B ISSUED "AS-BUILT"

1. REVISED FWD BHD OF COMPT NO. 3-29-1 FROM I-1 TO M-7 ANTISWEAT

TREATMENT.

2. REVISED 6.2 M TO 6.25 M.

ITEM 1 TO SUIT ECN 631-01-010.

ITEM 2 TO SUIT GOVT. RESPONSE dtd 7/12/13

B5

14,35

DESCRIPTION

INTIAL ISSUE

SCALE: NONE

REVISIONS

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

REV

BABS APRV:

INCORPORATED ECN 001.

INCORPORATED ECN 002.

INCORPORATED ECN 003 - ADD SHEET 36.

ECN 004 - Supercede with ECN 005 - NO CHANGE.

INCORPORATED ECN 005 - ADD SHTS 12A,18A,20A,21A,28A,30A & ADDED GEN. NOTE

#16.

INCORPORATED ECN 006 - ADD GEN. NOTE #15.

ECN 007 - NOTED SIM. TO ECN 006 - NO CHANGE.

INCORPORATED ECN 008

INCORPORATED ECN 009

GOVERNMENT RESPONSE(s) DATED 6-4-12 & 11-10-12 Update to Suit ECN 003 comment add Bow Thruster Tunnel Text to Area box.

A

DATE:

DATE:

SHEET 3

Continued on sheet 3A

GENERAL NOTES

1. Surfaces of fuel oil, lube oil, and dirty oil tanks are to be run through the wheelabrator for removal of mill scale, and are to be left uncoated.

All preconstruction primer shall be removed prior to fueling.

2. All paints and coatings shall be mixed and applied in accordance with standard painting procedures and manufacturers recommendations.

The coating manufacturer’s instructions for acceptable ambient and metal surface temperature, relative humidity, and dew point, surface cleanliness, surface profile, dry film thickness, and drying/cure/recoat times shall be followed.

3. IF required, equipment with factory installed coating systems shall be touched up with matching paint.

4. Do not paint door hardware, cathodic protection anodes, bond straps, heat exchanger surfaces, gasket seats, lubricating fittings, nameplates, labels & signs, threads and working surfaces, rubber & other elastomers, discharge nozzles, decorative & finished parts of furniture, furnishings & equipment, isolation mounts, type II acoustic treatment, and below waterline temperature sensors and acoustic transducers. Surfaces of unexposed aluminum structure behind insulation and/or joiner panels do not require coating. Perforated sheathing shall not be sprayed after installation.

5. Surface to be painted must be at least 5 degrees F above dew point to prevent condensation.

6. Anchor Chain Markings:

The anchor chains shall be painted and marked to identify the length of chain paid out as follows:

a. One link on each side of the 15 fathom detachable link shall be painted white, Part Number N3.

b. Two links on each side of the 30 fathom detachable link shall be painted white, Part Number N3.

c. Three links on each side of the 45 fathom detachable link shall be painted white, Part Number N3.

Marking shall continue in this fashion to the bitter end of the chain.

Detachable links shall be painted as follows:

a. 15 fathom detachable link, red, Part Number N6.

b. 30 fathom detachable link, white, part Number N3.

c. 45 fathom detachable link, blue, Part Number N7.

d. 60 fathom detachable link, red, Part Number N6.

Subsequent detachable links shall be painted in colors that continue this color sequence.

7. Hull markings shall be located IAW Ref 3 and painted (DFT 4 mil) with the following:

Hull Mark Part Number Draft Marks (Calculative & appendage) N3 OR N5 Thruster Marks N5 Ship's Name N5 NOAA Symbol N7 OR N9

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

8. Where referred to this note from the list of compartments, paint system I-4 and I-6 shall be used in way of exposed structure and insulation.

9. Where referred to this note from the list of compartments, paint system I-4 shall be used in way of exposed structure.

10. Engine exhaust and other surfaces above 93 degrees C, unlagged shall use Paint System "M4".

11. Foundations above floor plates in machinery spaces shall use Paint System "M5".

12. Uninsulated area's which are weather boubdries shall use Paint System "M-7".

13. Valve hand wheels, operating levers and root valves away from guageboards located in the interior of the ship shall be color coded for training, troubleshooting, quick identification, proper operation of particular systems and critical control or casualty control process.

Fresh Water Machinery Cooling Dark Blue COOLING FW Fresh Water Potable Light Blue POTABLE WTR Seawater Green SW Uncontaminated Seawater Green Stripped UNCSW Fire Systems and Mains Red FIREMAIN Diesel Fuel Brown DIESEL Lubricating Oil Yellow LO Hyraulic Systems Orange HYDRAULIC Ship Service Air Black SS AIR Starting & Control Air White S/C AIR Sewage Brown/Yellow SEWAGE Vacuum Yellow/Red VAC Chilled Water Green/Blue CHILLED Diver's Air Black/White DIVERS AIR

14. All resident US Navy and Trelleborg/Metalastick type shock mounts within structural machinery mounts shall be coated with Spraylat SC-1071T Strippable Coating prior to any other painting within he immediate area. Particular attention shall be paid to mounts for large machinery.

15. All aluminum exterior decks and 150mm up adjacent verticle surfaces, house tops, exterior hatch covers, foundations, deck fittings and inboard side bulwalks shall be sweep blasted SSPC-SP-7 prior to application of specified coatings.

16. Interior steel surfaces that are to receive systems D-7, I-1, I-2, I-3, I-4, M-5 and M-7 were primed with N22 Amercoat 385 in compartments located in Modules 101, 103, 201, 202, 301, 302 and 401. D-7A, I-1A, I-4A, M-5A and M-7A were primed were primed with N14 Amercoat 385 in compartments located in modules 102, 303, 402, 403, 501, 502, 505, and 506. DATE:

DATE:

SHEET 3A

REV

BABS APRV:

SCALE: NONE

GENERAL NOTES (Continued)

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

System Color Abbreviation

PART

NO.

UNIT OF

MEAS

Qty

(EST)

COLOR

N1 Gallon 98 Terracotta N2 Gallon 98 Black N3 Gallon 109 White N4 N5 Gallon 23 Black N6 Gallon 3 Red N7 Gallon 5 Dark Blue N8 Gallon 16 Buff N9 Gallon 2 Light Blue N10 Gallon 13 White N11 Gallon 7 Haze Gray N12 Gallon 13 Buff N13 Gallon 80 Green N14 Gallon 636 Terracotta N15 Gallon 108 Black N16 Gallon 60 Off White N17 Gallon 217 Dark Gray N18 Gallon 11 Terracotta N19 Gallon 11 Black N20 Gallon 4 Aluminum N21 Gallon 5 Black N22 Gallon 190 Terracotta N23 Gallon 385 NQA933 Gray

N24 Gallon 55 N/A

N25 Gallon 384 White N26 Gallon 9 Gray N27 Gallon 122 White N28 Gallon 61 Haze Grey N29 Gallon 122 Buff N30 Gallon 10 White N31 N32 Gallon 55 N33

DATE:

DATE:

SHEET 4SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

REV

BABS APRV:

LIST OF MATERIALS

Ablative antifouling Ameron ABC #4 Epoxy, acrylic, gloss Ameron Amercoat 229C

DESCRITON

TYPE/CLASS/GRADE

MFG. PRODUCT

NAME/NUMBER

Ablative antifouling Ameron ABC #4

REMARKS

Epoxy, acrylic, gloss Ameron Amercoat 229T Epoxy, acrylic, gloss Ameron Amercoat 229T

NOT USED

Epoxy, acrylic, gloss Ameron Amercoat 229T

Epoxy, high solids Ameron Amerlock 2 Epoxy, high solids Ameron Amerlock 2

Epoxy, acrylic, gloss Ameron Amercoat 229T Epoxy, acrylic, gloss Ameron Amercoat 229T

Epoxy, multipurpose Ameron Amercoat 385 Epoxy, multipurpose Ameron Amercoat 385

Epoxy, high solids Ameron Amerlock 2 Primer, reinforced inorganic zinc Ameron Dimetcote 302H

Epoxy, high solids, glass flake Ameron Amerlock 400GFK Epoxy, high solids, glass flake Ameron Amerlock 400GFK

Glassflake Glassflake

Epoxy, multipurpose Ameron Amercoat 385 Epoxy, multipurpose Ameron Amercoat 385

Primer, Alkyd Ameron Amercoat 5105 Pre-construction Primer International Interplate 937

High temperature silicone coating Ameron Amercoat 878 Top Coat, alkyd, gloss Ameron Amercoat 5450

Top Coat, alkyd, gloss Ameron Amercoat 5450 Epoxy, Universal, Semigloss Ameron Amercoat 240

FLO-COAT MIL-C-16173

Eureka Chemical Company

Fluid Film A Top Coat, alkyd, gloss Ameron Amercoat 5450

Fill & drain inaccessible voids

Epoxy, Universal, Semigloss Ameron Amercoat 240 Temp-Coat, Antisweat Treatment Temp-Coat 101

Epoxy, Universal, Semigloss Ameron Amercoat 240

Holding Primer Picklex 20 Inhibitor Test Equipment Elcometer

NO.

UNIT OF

MEAS

Qty

(EST)

COLOR

N34 Gallon 270 White N35 Gallon 68 Oxide Red N36 Gallon Buff N37 Gallon 5 Red N38 Gallon 5 Brown N39 Gallon 5 Yellow N40 Gallon 5 Orange N41 Gallon 5 Black N42 Gallon 5 Blue N43 Gallon 5 Dark Blue N44 Gallon 5 Light Blue N45 Gallon 5 Green N46 Gallon 1 Silver N47 Gallon 50 N48 Gallon 50

DATE:

DATE:

SHEET 4ASCALE: NONE

Mid Graphite Gray

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

REV

BABS APRV:

Nonskid Aggregate Amercoat 888 Aluminum Oxide Epoxy Multi-Purpose Amercoat AT 385-257

Topcoat, Alkyd Gloss Amercoat 5450 Brite Zinc Brite zinc Gallon Can Touch Up Galvanizing

Topcoat, Alkyd Gloss Amercoat 5450 Topcoat, Alkyd Gloss Amercoat 5450

Topcoat, Alkyd Gloss Amercoat 5450 Topcoat, Alkyd Gloss Amercoat 5450

Topcoat, Alkyd Gloss Amercoat 5450 Topcoat, Alkyd Gloss Amercoat 5450

Topcoat, Alkyd Gloss Amercoat 5450

Potable Water Tank Lining Amercoat 133 Epoxy Multi-Purpose Primer Sigmacover 435US

LIST OF MATERIALS

DESCRITON

TYPE/CLASS/GRADE

MFG. PRODUCT

NAME/NUMBER

REMARKS

Potable Water Tank Lining Amercoat 133

Topcoat, Alkyd Gloss Amercoat 5450

DECK OVHD FWD AFT PORT STBD

101 4-1-0 T-2 T-2 T-2 T-2 T-2 T-2 101 4-7-1 - - - - - - 101 4-7-2 - - - - - - 102 1-4-0 D-2 I-4A I-4A I-1A I-4A I-4A 102 1-7-0 - I-4A I-4A I-4A I-4A N/A 102 2-5-0 D-7A M-3 M-3 M-3 M-3 M-3 102 2-7-0 D-2 I-1A I-4A I-1A I-4A I-1A 102 4-1-0 T-2 T-2 T-2 T-2 T-2 T-2 102 1-7-1 D-7A I-4A I-4A I-1A I-1A I-1A 102 1-16-1 D-2 I-4A I-1A I-1A I-1A I-4A 102 2-7-1 D-2 I-1A I-4A I-1A I-1A I-4A 102 2-11-1 D-7A I-1A I-1A I-1A I-1A I-4A 102 1-11-2 D-7A I-4A I-4A I-4A I-4A I-4A 102 2-16-2 D-7A I-1A I-1A I-1A I-4A I-1A 102 1-7-3 D-2 I-4A I-4A I-1A I-1A I-4A 103 3-13-0 D-2 I-4 I-4 I-4 I-4 I-4 103 4-13-0 U-2 U-2 U-2 U-2 U-2 U-2 103 4-19-0 T-2 T-2 T-2 T-2 T-2 T-2 103 4-23-0 D-2 I-1 I-1 I-1 I-1 I-1 103 3-19-1 T-3 T-3 T-3 T-3 T-3 T-3 103 4-13-1 T-2 T-2 T-2 T-2 T-2 T-2 103 4-19-1 - - - - - - 103 3-19-2 T-3 T-3 T-3 T-3 T-3 T-3 103 4-13-2 T-2 T-2 T-2 T-2 T-2 T-2 103 4-19-2 - - - - - - 201 3-29-0 D-2 I-4 I-4 I-4 I-4 I-4 201 3-29-1 D-2 I-4 M-7 I-1 I-1 I-4 201 3-31-0 D-2 I-1 I-1 I-1 I-1 I-1 201 3-32-1 D-2 I-4 I-1 I-1 I-1 I-4 201 4-29-0 - - - - - ` 201 4-29-1 T-2 T-2 T-2 T-2 T-2 T-2 201 4-29-2 T-2 T-2 T-2 T-2 T-2 T-2 201 3-39-0 D-2 I-1 I-1 I-1 I-1 I-1 201 3-39-1 - - - - - - 201 3-39-2 - - - - - -

DATE:

DATE:

SHEET 5

REV

BABS APRV:

Scientific Stores

LIST OF COMPARTMENTS (BY MODULE)

SURFACE SYSTEMMODULE COMPT # DESIGNATION

Forepeak Ballast DT #1FS Fuel Oil DT #1FP Fuel Oil Scientific Stores

Freeze Room Chain Locker

REMARKS

See General Note 1

DT #1AP Ballast DT#2P Fuel Oil

Fresh Water Tank DT #1AS Ballast DT#2S Fuel Oil

Fresh Water Tank

Access Dry Stores

Bow Thruster Mchry Room Bow Thruster Seachest

Permanent Ballast Transducer Room

Chill Room

See General Note 1

DT #3P Ballast Auxiliary Machinery Room

Fuel Oil Day Tank Fuel Oil Day Tank

Domestic Equipment Room

Access

DB #3C FUEL OIL

DT #3S Ballast

Locked Stores

General Stores

EM Bhd=I-1 Forepeak Ballast Stores Loading

Fan Room Steward Stores

Laundry

See General Note 1

See General Note 1

See General Note 1

Antisweat Required @ FWD bulkhead

See General Note 1 See General Note 1

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

201 3-47-0 D-2 I-1 I-4 I-4 I-4 I-4 201 3-47-01 - - - - - - 201 4-34-0 T-2 T-2 T-2 T-2 T-2 T-2 201 4-39-0 T-2 T-2 T-2 T-2 T-2 T-2 201 4-39-01 - - - - - - 201 4-39-1 - - - - - - 201 4-39-2 - - - - - - 201 4-47-1 - - - - - - 201 4-47-2 T-2 T-2 T-2 T-2 T-2 T-2 202 1-19-0 D-7 I-4 I-4 I-4 I-4 I-4 202 2-19-0 D-2 I-1 I-4 I-4 I-4 I-4 202 2-29-0 D-2 I-1 I-4 I-1 I-4 I-4 202 3-31-0 D-2 I-1 I-1 I-1 I-1 I-1 202 1-19-1 D-7 I-4 I-4 I-4 I-4 I-4 202 1-31-1 D-7 I-4 I-4 I-4 I-4 I-4 202 2-19-1 D-7 I-4 I-4 I-4 I-4 I-4 202 2-19-2 D-2 I-1 I-4 - - I-1 202 2-19-4 D-7 I-1 I-4 I-4 I-4 - 202 2-19-6 D-2 I-1 I-4 I-4 I-4 - 202 1-33-1 D-2 I-4 - I-1 I-1 - 202 1-36-0 D-7 I-1 I-1 I-1 I-1 I-1 202 1-38-2 D-7 I-4 I-4 I-4 I-4 I-4 202 1-40-1 D-2 I-4 I-4 I-4 I-4 I-4 202 1-43-2 D-7 I-1 I-1 I-4 I-1 I-4 202 2-29-1 D-7 I-4 I-4 - - I-4 202 2-29-2 D-7 I-4 I-4 - I-4 - 202 2-34-1 D-7 I-4 - I-4 I-1 I-4 202 2-34-2 D-7 I-4 - I-4 I-4 I-4 202 2-39-0 D-7 I-1 I-4 I-1 I-4 I-4 202 2-39-1 D-2 I-4 I-4 - I-4 - 202 2-39-3 D-7 I-4 I-4 - - I-4 202 2-39-2 D-7 I-4 I-4 - I-4 - 202 2-44-1 D-7 I-4 - I-4 I-4 I-4

DATE:

DATE:

SHEET 5A

LIST OF COMPARTMENTS (BY MODULE)

MODULE COMPT # DESIGNATION SURFACE SYSTEM REMARKS

Access Lube Oil Tank See General Note 1

Waste Water Tank Centerboard Trunk

DB #4C Fuel Oil See General Note 1 DB #4S Fuel Oil See General Note 1 DB #4P Fuel Oil See General Note 1 Waste Oil Tank See General Note 1

Oily Water Waste Tank Mess Room IMU Room

Passage Access

Galley / Scullery Dry Lab

Stateroom (2) CG Locker

Exercise Room Access

Scientific Equipment Room Passage

Acoustic / Computer Lab Hydrographic Lab

Toilet Stateroom (2) Stateroom (2) Stateroom (2) Stateroom (2)

Passage Linen Locker

Stateroom (2) Stateroom (2) Stateroom (2)

USCG APRV:

REV

BABS APRV:

SCALE: NONE

SIZE

A

FSCM CAGE NO

98042

202 2-44-2 D-7 I-4 - I-4 I-4 I-4 202 4-39-0 - - T-2 T-2 T-2 T-2

301 3-68-0 D-2 I-4 I-1 I-1 I-4 I-4

301 3-69-2 D-2 I-1 I-1 I-1 I-1 I-1 301 4-49-0 D-6 I-4 I-4 I-4 I-4 I-4 301 5-49-0 - - - - - - 301 4-61-1 U-2 U-2 U-2 U-2 U-2 U-2 301 4-61-2 U-2 U-2 U-2 U-2 U-2 U-2

301 4-49-1 VOID T-2 T-2 T-2 T-2 T-2 T-2

302 2-63-0 D-7 I-4 I-4 I-4 I-4 I-4 303 1-36-0 D-7A I-1A I-1A I-1A I-1A I-1A 303 1-47-0 D-7A I-4A I-4A I-4A I-4A I-4A 303 1-51-2 D-2 I-1A I-4A I-4A I-4A I-4A 303 1-56-2 D-7A I-1A I-1A I-1A I-1A I-1A 303 1-58-1 D-7A I-4A I-4A I-4A I-4A I-4A 303 1-58-2 D-7A I-4A I-4A I-4A I-4A I-4A 303 1-63-2 D-2 I-4A I-4A I-1A I-4A I-4A 303 1-63-4 D-7A I-1A I-1A I-1A I-1A I-1A 303 1-65-4 D-2 I-4A I-4A I-4A I-4A I-4A 303 1-66-1 D-7A I-4A - I-4A I-4A - 303 4-49-0 D-6 I-4A I-4A I-4A I-4A I-4A 303 4-49-0 - - I-4A I-4A I-4A I-4A 401 4-78-0 T-2 T-2 T-2 T-2 T-2 T-2 402 1-58-1 D-7A I-4A I-4A I-4A I-4A I-4A 402 1-70-2 D-2 I-4A I-1A I-1A I-1A I-1A 402 1-70-4 D-2 I-4A I-4A I-4A I-4A I-4A 402 1-78-2 D-2 I-4A I-1A I-4A I-1A I-4A 402 1-78-4 D-2 I-4A I-4A I-4A I-4A I-1A

402 3-68-0 D-2 I-4A I-1A I-1A I-4A I-4A

403 3-72-1 - - - - - - See General Note 1 403 3-72-2 - - - - - -

403 3-82-0 D-2 I-4A I-4A I-4A I-4A I-4A

DATE:

DATE:

SHEET 5B

Escape Trunk Main Machinery Room

Stateroom (2) Centerboard Trunk

Oceanographic Winch Room Sci/Bosn Stores

LIST OF COMPARTMENTS (BY MODULE)

MODULE COMPT # DESIGNATION

SURFACE SYSTEM

REMARKS

Fuel Tank See General Note 1 Seachest Seachest

Engineer's Operating Station Passage

Chemistry Lab Access

CG Locker Fish Lab/ Wet Lab

Trash Room Scientific Freezer

Controlled Environment Rm Scientist Ready Room

Water Closet

Fish Lab/ Wet Lab

Hazmat/ Paint Locker

Main Machinery Room MMR Sup and Exh Trunk

Bossing (Skeg)

Oceanographic Winch Room Sci/Bosn Stores

Scientific hazmat Locker Ready Room Deck Locker

REV

BABS APRV:

DT #5P Fuel Oil See General Note 1

USCG APRV:

Trawl Winch Room Sci/Bosn Stores

DT #5S Fuel Oil

SCALE: NONE

SIZE

A

FSCM CAGE NO

98042

501 01-19-0 D-7A I-6 - - - - 501 01-33-1 D-7A - - - - - 501 01-33-2 D-7A - - - - - 501 01-37-0 D-2 I-6 I-6 I-6 I-6 I-6 501 01-37-2 D-7A - - - - - 501 01-43-1 D-4 - - - - - 501 01-44-1 D-2 I-6 I-6 I-6 I-6 I-6 501 01-47-2 D-7A - - - - - 501 02-37-0 D-8 I-6 - - - - 501 02-37-2 D-8 - - - - - 501 02-39-1 D-8 - - - - - 501 02-45-0 D-8 I-6 - - - - 501 02-45-1 D-8 - - - - - 501 02-46-2 D-8 - - - - - 501 02-47-1 D-4 I-6 - - - - 501 02-50-3 D-8 - - - - - 501 02-53-2 D-3 I-6 I-6 I-6 I-6 I-6 501 1-51-2 D-7A I-6 I-6 I-6 I-6 I-6 501 4-39-0 501 02-50-1 - I-6 - - - - 502 01-10-0 D-2 I-6 I-6 I-6 I-6 I-6 502 01-14-0 D-1 E-4 E-4 E-4 E-4 E-4 502 01-19-0 D-7A I-6 - - - - 502 02-22-0 T-4 T-4 T-4 T-4 T-4 T-4 502 02-29-0 D-8 - - - - - 502 01-10-1 D-3 I-6 I-6 I-6 I-6 I-6 502 01-12-1 D-3 I-6 I-6 I-6 I-6 I-6 502 01-19-1 D-7A - - - - - 502 01-28-1 D-7A I-6 - - - - 502 01-31-1 D-2 I-6 - - - - 502 01-10-2 D-2 I-6 I-6 I-6 I-6 I-6 502 01-19-2 D-7A - - - - - 502 01-24-2 D-7A - - - - - 502 01-28-2 D-7A - - - - -

DATE:

DATE:

SHEET 5C

See General Note 9Toilet

See General Note 8

See General Note 8

Passage

Stateroom (2)

DC Locker See General Note 8

Passage See General Note 8 Roll Stabilization Tank See General Note 8

StateRoom (2) See General Note 8 Dive Locker See General Note 9

LIST OF COMPARTMENTS (BY MODULE)

MODULE COMPT # DESIGNATION SURFACE SYSTEM REMARKS

Passage See General Note 8 Stateroom (2) See General Note 8 Stateroom (2) See General Note 8

Fan Room see General Note 9 Office Suite See General Note 8

Side Sampling Control Booth See General Note 8

ET Shop See General Note 8 Passage See General Note 8

Stateroom (2) See General Note 8 Stateroom Sr Cmd Officer See General Note 8

CG Locker See General Note 8 Stateroom (2) See General Note 8

Centerboard Trunk See General Note 9

Stateroom (2) See General Note 8 Linen Locker See General Note 8

Hospital See General Note 8

Linen Locker See General Note 8 Refrigeration Machinery See General Note 8

CO2 Room See General Note 8

CG Locker

Deck Locker See General Note 9 Lounge & Conference Room See General Note 8

See General Note 8

DC Locker See General Nore 9 Access See General Note 8

REV

BABS APRV:

SCALE: NONE

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Stateroom (2) See General Note 8 Stateroom (2) See General Note 8

USCG APRV:

502 2-16-2 D-8 I-4 I-6 I-6 I-4 I-6 502 02-29-1 D-8 - - - - - 502 02-29-2 D-8 - - - - - 503 01-54-0 D-2 I-6 I-6 I-6 I-6 I-6 505 4-49-0 - - - - - - 506 03-34-0 D-8 I-6 I-6 I-6 I-6 I-6 507 - E-4 E-4 E-4 E-4 E-4

DATE:

DATE:

SHEET 5D

LIST OF COMPARTMENTS (BY MODULE)

MODULE COMPT # DESIGNATION SURFACE SYSTEM REMARKS

Access See General Note 9 Stateroom Chief Scientist See General Note 8 Stateroom Chief Engineer See General Note 8

Emergency Generator Room See General Note 9 MMR Sup & Exh Trunk See General Note 8

Bridge See General Note 9 Mast

USCG APRV:

REV

BABS APRV:

SCALE: NONE

SIZE

A

FSCM CAGE NO

98042

MIN MAX Nozzle N13 Green FULL 4.0 3.0 4 Hr 3 Mo X 0.021" N14 Terracotta FULL 8.0 5.0 8 Hr - X 0.021" N47 FULL 8.0 5.0 9 Hr - X 0.021"

Touch Hard 78% Powder 4 Hr 6 Hr 66% Part B 2 Hr 16 Hr

DATE:

DATE:

SHEET 6

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Remarks: Non skid grit as recommended by PPG Protective and Marine Coatings is to be added to the finish coat on all deck surfaces except for the trawlway and trawlway inclined ramp.

Notes:

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

1:1 8 Hr 99 32 120 1:1 3 Hr 85 40 120

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time

(DFT)

(6 mil) at 70° F

PAINT SYSTEM "D-1"

212 148

AREA: All exterior steel decks (150 mm up on vertical surfaces), house tops, trawlway, trawlway ramp, exterior hatch covers/coamings, foundations, deck fittings, and inboard side of bulwarks.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to 1st coat Blast damaged areas near white to SSPC- SP10 finish. Sand sweep remaining area to SSPC- SP7 finish.

Dimetcote 302H 417 292 Amercoat 385 212 148

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Brush Roller Conv.

Spray

Airless SprayTheoretical Practical

Application Method Airless Spray

Fan

APPLICATION

Humidity

90%

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

Amercoat 385

Part Number

Dimetcote 302H Amercoat 385

PRODUCT INFORMATION

Mid Graphite

Gray

50%

MIN MAX

N17 Dark Gray FULL 9.0 6.0 8 Hr - X 0.021" N14 Terracotta FULL 9.0 6.0 8 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr

DATE:

DATE:

SHEET 7

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° F

1:1 3 Hr

AREA: Exposed interior steel decks (150 mm up on vertical surfaces) in auxiliary machinery and service spaces, workshops, storerooms, deck lockers and similar spaces.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to 1st under coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

Application Method Airless Spray

Fan Airless Spray

Amercoat 385 176 124 Amercoat 385 176 124

Brush Roller Conv.

Spray

SYSTEM

INFORMATION

COLOR

Remarks: Notes:

PRODUCT INFORMATION

Amercoat 385 85 40 120

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

APPLICATION

Humidity

MAXMIN

PAINT SYSTEM "D-2"

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

NUMBER

N14 Terracotta FULL 9.0 6.0 8 Hr - X 0.021" N17 Dark Grey FULL 9.0 6.0 8 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr

DATE:

DATE:

SHEET 8

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Remarks: Non skid grit as recommended by PPG Protective and Marine Coatings is to be added to the finish coat. Notes:

85 40 120

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

APPLICATION

Humidity

MAXMIN

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° F

1:1 3 Hr

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical Amercoat 385 176 124

SYSTEM

INFORMATION

Amercoat 385 176 124

Brush Roller Conv.

Spray

Airless Spray

Application Method Airless Spray

Fan

COLOR

PAINT SYSTEM "D-3"

PART

NUMBER

AREA: All aluminum exterior decks (150 mm up on vertical surfaces) house tops, exterior hatch covers, foundations, deck fittings and inboard side of bulwarks.

SURFACE PREPARATION:

1) Prep prior to 1st under coat: Sandsweep SSPC-SP-7

PRODUCT INFORMATION

Amercoat 385

N17 Dark Grey FULL 9.0 6.0 8 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr

DATE:

DATE:

SHEET 9

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Remarks: Non skid grit as recommended by PPG Protective and Marine Coatings is to be added to the finish coat. Notes:

85 40 1203 HrAmercoat 385 1:1

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° FPRODUCT INFORMATION

PAINT SYSTEM "D-4"

Amercoat 385 176 124

Brush Roller Conv.

Spray

Airless Spray

AREA: All aluminum interior decks (150 mm up on vertical surfaces)

SURFACE PREPARATION:

1) Power wash/degrease @ 344.7 bar (5000 PSI).

2) Prep prior to 1st under coat: Sandsweep SSPC-SP-7

PART

NUMBER

Application Method Airless Spray

Fan Amercoat 385 176 124

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

APPLICATION

Humidity

MIN MAX

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

N14 Terracotta FULL 8.0 5.0 8 Hr - X 0.021" N5 Black FULL 4.0 2.0 6 Hr - X 0.021"

Touch Hard 78% Powder 4 Hr 6 Hr 66% Part B 2 Hr 16 Hr 56% Part B 2 Hr 8 Hr

DATE:

DATE:

SHEET 10

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Notes:

40 120 1:1 3 Hr 85 40 120 -

32 120

Flash Point (degrees F)

Air Temperature (degrees F)

MIN MAX

APPLICATION

Humidity

MAXMIN

50% 90%

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time

(DFT)

(6 mil) at 70° F

1:1 8 Hr

Amercoat 229T 449 337

PAINT SYSTEM "D-5"

Amercoat 385 212 148

Brush Roller Conv.

Spray

Airless Spray

AREA: Steel deck machinery, electric brakes, motor housing exteriors, deck mounted chocks/cleats/bitts and fairleads.

SURFACE PREPARATION: 1) Material is to be blasted near white to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

PART

NUMBER

Application Method Airless Spray

Fan Dimetcote 302H 417 292

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

Remarks: All required surface preparation is for structural elements prior to final assembly.

PRODUCT INFORMATION

Dimetcote 302H Amercoat 385

Amercoat 299T

4:1 6 Hr 80

N17 Dark Grey FULL 9.0 6.0 8 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr

DATE:

DATE:

SHEET 11

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Remarks: Notes:

1:1 3 Hr 85 40 120

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

APPLICATION

Humidity

MIN MAX

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° FPRODUCT INFORMATION

PAINT SYSTEM "D-6"

Amercoat 385 176 124

Brush Roller Conv.

Spray

Airless Spray

AREA: Walking surfaces of floor plates, grates, decks, and platforms in main machinery spaces.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to under coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

3) Prep prior to finish coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

PART

NUMBER

Application Method Airless Spray

Fan Amercoat 385 176 124

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

N22 Terracotta FULL 3.5 2.0 8 Hr 24 Hr X 0.017"

Touch Hard 60% N/A 2 Hr 6 Hr

DATE:

DATE:

SHEET 12

REV

BABS APRV:

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time

(DFT)

(6 mil) at 70° F

PRODUCT INFORMATION

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Remarks: Notes:

PAINT SYSTEM "D-7"

Brush Roller Conv.

Spray

Airless Spray

AREA: Unexposed steel decks which receive deck covering or under enclosed furniture or equipment.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

PART

NUMBER

Application Method Airless Spray

Fan Amercoat 5105 481 337

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

Amercoat 5105

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

APPLICATION

Humidity

MIN

MAX

N/A - 100 40 110

N14 Terracotta FULL 8.0 5.0 8 Hr X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr

DATE:

DATE:

SHEET 12ASCALE: NONE

Remarks: Notes:

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

REV

BABS APRV:

-Amercoat 385 N/A 3 Hr 85 40 120 -

Flash Point (degrees F)

APPLICATION

Temperature (degrees F) Humidity

MIN MAX MIN MAX

PRODUCT INFORMATION

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time

(DFT)

(6 mil) at 70° F

Theoretical Practical Fan Amercoat 385 212 148

Overcoat Time @ 70° F

Application Method

Brush Roller Conv.

Spray

Airless Spray

Airless Spray

PAINT SYSTEM "D-7A"

AREA: Unexposed steel decks which receive deck covering or under enclosed furniture or equipment.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

PART

NUMBER

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Touch Hard

DATE:

DATE:

SHEET 13

AREA: Aluminum decks to receive deck covering other than paint. SURFACE PREPARATION:

1) Power wash/degrease @ 344.7 bar (5000 PSI).

2) Prep prior to 1st under coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

PART

NUMBER

Airless Spray

Application Method Airless Spray

Fan

PAINT SYSTEM "D-8"

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical Brush Roller

Conv.

Spray

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

PRODUCT INFORMATION

APPLICATION

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time

(DFT)

(6 mil) at 70° F Humidity

MAX

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Remarks: Notes:

MIN

N14 Terracotta FULL 8.0 5.0 8 Hr - X 0.021" N3 White FULL 4.0 2.0 6 Hr - X 0.021"

Touch Hard 78% Powder 4 Hr 6 Hr 66% Part B 2 Hr 16 Hr 56% Part B 2 Hr 8 Hr

DATE:

DATE:

SHEET 14

PAINT SYSTEM "E-1"

AREA: Shell exterior from 6.25 meter water line up through turn of gunwale including the outboard side of the bulwarks.

Continued in Remarks

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to 1st under coat: Blast damaged areas near white to SSPC- SP10 finish. Sand sweep remaining area to SSPC- SP7 finish.

PART

NUMBER

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical Brush Roller

Conv.

Spray

Airless Spray

Application Method Airless Spray

Fan

Amercoat 229T 449 337

Dimetcote 302H 417 292 Amercoat 385 212 148

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time

(DFT)

(6 mil) at 70° F Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

PRODUCT INFORMATION

APPLICATION

MAX

90%

Humidity

MIN

50%

40 120 -

1:1 8 Hr 99 32 120 N/A 3 Hr 85 4:1 6 Hr 80 40 120

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Notes:Remarks: Area (continued) Exterior steel deckhouses, vents, overflows, overhead surfaces, deck gear lockers, doors, stanchions, vertical and inclined ladders, handrails, ventilators, bulwark mounted chocks, davits and steel monorails.

Dimetcote 302H

Amercoat 229T

N14 Terracotta FULL 8.0 5.0 8 Hr - X 0.021" N8 Buff FULL 4.0 2.0 6 Hr - X 0.021"

Touch Hard 78% Powder 4 Hr 6 Hr 66% Part B 2 Hr 16 Hr 45% Part B 2 Hr 8 Hr

DATE:

DATE:

SHEET 15

AREA: Steel masts, booms, cranes, “A” frames, gantries, and similar fittings.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to 1st under coat: Blast damaged areas near white to SSPC- SP10 finish. Sand sweep remaining area to SSPC- SP7 finish.

PART

NUMBER

Airless Spray

Application Method Airless Spray

Fan

PAINT SYSTEM "E-2"

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical Dimetcote 302H 417 292 Amercoat 385 212 148

Brush Roller Conv.

Spray

Amercoat 229T 449 337

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

PRODUCT INFORMATION

Dimetcote 302H

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time

(DFT)

(6 mil) at 70° F

APPLICATION

Humidity

MAX

90%

N/A 3 Hr 85 40 120Amercoat 385 Amercoat 229T

1:1 8 Hr 99 32 120

4:1 6 Hr 80 40 120

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Remarks: Notes:

MIN

50%

N14 Terracotta FULL 8.0 5.0 8 Hr - X 0.021" N3 White FULL 4.0 2.0 6 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr 56% Part B 2 Hr 8 Hr

DATE:

DATE:

SHEET 16

SYSTEM

INFORMATION

COLOR

AREA: All exterior exposed vertical surfaces of the aluminum superstructure including vents, overflows, deck gear lockers, doors, stanchions, vertical and inclined ladders, handrails, ventilators, stack (excluding stack bands) and bulwarks. Also includes the underside of exposed deckheads

SURFACE PREPARATION:

1) Power wash/degrease @ 344.7 bar (5000 PSI).

2) Prep prior to 1st under coat: Sand sweep

PART

NUMBER

Airless Spray

Remarks: Notes:

APPLICATION

Application Method Airless Spray

Fan Amercoat 385 176 124

Amercoat 229T 449 337

Brush Roller Conv.

Spray

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° FPRODUCT INFORMATION

MAX

Humidity

MIN

40 120Amercoat 229T 1:1 3 Hr 85 40 120

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

Amercoat 385

-4:1 6 Hr 80

PAINT SYSTEM "E-3"

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

N14 Terracotta FULL 8.0 5.0 8 Hr 24 Hr X 0.021" N8 Buff FULL 4.0 2.0 6 Hr - X 0.021"

N14 Terracotta FULL 8.0 5.0 8 Hr 24 Hr X 0.021" N5 N7 N9

Touch Hard 66% Part B 2 Hr 16 Hr 56% Part B 2 Hr 8 Hr

DATE:

DATE:

SHEET 17

Remarks: Top band:(Black/N5) 2/15 of stack height, Middle band (light blue/N9) 1/15 of stack height. Bottom band (dark blue/N7) 1/15 of stack height. Bands are to be parallel to baseline and permanently marked. Top band is to be measured from the top of the stack. There is no separation between bands.

Notes:

MAX

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° F Humidity

APPLICATION

Airless Spray Fan

X 0.021"

PAINT SYSTEM "E-4"

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

Application Method

AREA: Aluminum masts, booms, trusses and similar fittings.

Stack Bands.

SURFACE PREPARATION:

1) Power wash/degrease @ 344.7 bar (5000 PSI).

2) Prep prior to 1st under coat: Sand sweep

PART

NUMBER

Amercoat 385 176 124 Amercoat 229T 449 337

Brush Roller Conv.

Spray

Airless Spray

Stack Bands Amercoat 385 176 124

Amercoat 229T See

Remarks

FULL 4.0 2.0 337449

PRODUCT INFORMATION

1:1 3 Hr 85 40 120

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

Amercoat 385

MIN

4:1 6 Hr 80 40 120Amercoat 229T -

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

N22 Terracotta FULL 3.5 2.0 8 Hr 24 Hr X 0.017" N25 White FULL 7.0 3.0 12 Hr - X 0.021"

Touch Hard 60% N/A 2 Hr 6 Hr 45% N/A 1.5 Hr 6 Hr

DATE:

DATE:

SHEET 18

Brush Roller Conv.

Spray

PAINT SYSTEM "I-1"

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical Airless Spray

Fan

AREA: All exposed interior steel bulkheads and overheads in machinery and service spaces, workshops, storerooms, deck lockers and similar spaces, interior railings, stanchions and associated fittings.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to under coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

3) Prep prior to finish coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

PART

NUMBER

Application Method Airless Spray

Amercoat 5105 481 337 Amercoat 5450 241 168

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX MIN

Humidity

APPLICATION

MAX

-Amercoat 5105

N/A - 98 45 100 N/A - 100 40 110

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° FPRODUCT INFORMATION

-Amercoat 5450 -

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

N16 Off White FULL 8.0 5.0 8 Hr 24 Hr X 0.021" N25 White FULL 7.0 3.0 12 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr 45% N/A 1.5 Hr 6 Hr

DATE:

DATE:

SHEET 18ASCALE: NONE

Remarks: Notes:

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

REV

BABS APRV:

Amercoat 5450 N/A - 98 45 100 - - Amercoat 385 N/A 3 Hr 85 40 120 -

Flash Point (degrees F)

APPLICATION

Temperature (degrees F) Humidity

MIN MAX MIN MAX

PRODUCT INFORMATION

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° F

Amercoat 5450 241 168

Theoretical Practical Fan Amercoat 385 212 148

Overcoat Time @ 70° F

Application Method

Brush Roller Conv.

Spray

Airless Spray

Airless Spray

PAINT SYSTEM "I-1A"

AREA: All exposed interior steel bulkheads and overheads in machinery and service spaces, workshops, storerooms, deck lockers and similar spaces, interior railings, stanchions and associated fittings.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to under coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

3) Prep prior to finish coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

PART

NUMBER

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

N25 White FULL 7.0 3.0 12 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr 45% N/A 2 Hr 12 Hr

DATE:

DATE:

SHEET 19

Brush Roller Conv.

Spray

PAINT SYSTEM "I-2"

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

Application Method Airless Spray

Fan

AREA: Exposed interior aluminum bulkheads and overheads. SURFACE PREPARATION:

1) Power wash/degrease @ 344.7 bar (5000 PSI).

2) Prep prior to 1st under coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

PART

NUMBER

Airless Spray

Amercoat 385 212 148 Amercoat 5450 241 168

MIN

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° FPRODUCT INFORMATION

APPLICATION

Humidity

MAX

Amercoat 5450 1:1 3 Hr 85 40 120

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

Amercoat 385

-N/A N/A 98 45 100

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

N22 Terracotta FULL 3.5 2.0 8 Hr 24 Hr X 0.17 N21 Black FULL 7.0 3.0 12 Hr - X 0.021"

Touch Hard 60% N/A 2 Hr 6 Hr 59% N/A 1.5 Hr 6 Hr

DATE:

DATE:

SHEET 20

Brush Roller Conv.

Spray

PAINT SYSTEM "I-3"

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

Application Method Airless Spray

Fan

AREA: All interior steel ladders outside of tanks. SURFACE PREPARATION: Blast to SSPC-SP 7 prior to 1st coat.

PART

NUMBER

Airless Spray

Amercoat 5105 481 337 Amercoat 5450 241 168

MIN

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° FPRODUCT INFORMATION

APPLICATION

Humidity

MAX

Amercoat 5450 N/A - 100 40 110

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

Amercoat 5105

-N/A - 108 45 100

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

N21 Black FULL 7.0 3.0 12 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr 59% N/A 1.5 Hr 6 Hr

DATE:

DATE:

SHEET 20ASCALE: NONE

Remarks: Notes:

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

REV

BABS APRV:

Amercoat 5450 N/A - 108 45 100 - - Amercoat 385 N/A 3 Hr 85 40 120 -

Flash Point (degrees F)

APPLICATION

Temperature (degrees F) Humidity

MIN MAX MIN MAX

PRODUCT INFORMATION

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° F

Amercoat 5450 241 168

Theoretical Practical Fan Amercoat 385 212 148

Overcoat Time @ 70° F

Application Method

Brush Roller Conv.

Spray

Airless Spray

Airless Spray

PAINT SYSTEM "I-3A"

AREA: All interior steel ladders outside of tanks. SURFACE PREPARATION: Blast to SSPC-SP 7 prior to 1st coat.

PART

NUMBER

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

N25 White FULL 7.0 3.0 12 Hr - X 0.021" N36 Buff FULL 5.0 3.0 3 Hr - X 0.021"

Touch Hard 45% N/A 1.5 6

DATE:

DATE:

SHEET 21

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Notes:Remarks: Amercoat 5450 is only to be applied on top of insulation. Amercoat 5450 shall not be applied to type II acoustic insulation.

N/A - 98 45 100

Temperature (degrees F)

MIN MAX

APPLICATION

Humidity

MAX

MIN

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° FPRODUCT INFORMATION

Amercoat 5450

Flash Point (degrees F)

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical Amercoat 5450 241 168 Sigmacoat 435 266 186

Brush Roller Conv.

Spray

AREA: Unexposed steel structure behind insulation and/or joiner panels.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to finish coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

PART

NUMBER

PAINT SYSTEM "I-4"

Airless Spray

Application Method Airless Spray

Fan

N36 Buff FULL 5.0 3.0 3 Hr - X 0.021"

Touch Hard 66% Part B 2 Hr 16 Hr 45% N/A 1.5 6

DATE:

DATE:

SHEET 21ASCALE: NONE

Remarks: Amercoat 5450 is only to be applied on top of insulation. Amercoat 5450 shall not be applied to type II acoustic insulation.

Notes:

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

REV

BABS APRV:

Amercoat 5450 N/A - 98 45 100 - - Amercoat 385 N/A 3 Hr 85 40 120 -

Flash Point (degrees F)

APPLICATION

Temperature (degrees F) Humidity

MIN MAX MIN MAX

PRODUCT INFORMATION

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° F

Sigmacoat 435 266 186

Theoretical Practical Fan Amercoat 385 212 148

Overcoat Time @ 70° F

Application Method

Brush Roller Conv.

Spray

Airless Spray

Airless Spray

PAINT SYSTEM "I-4A"

AREA: Unexposed steel structure behind insulation and/or joiner panels.

SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to finish coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

PART

NUMBER

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

N13 Green FULL 4.0 3.0 4 Hr 6 Mo X 0.021" N14 Terracotta FULL 9.0 6.0 8 Hr 24 Hr X 0.021"

Touch Hard 78% Part B 4 Hr 6 Hr 66% N/A 2 Hr 16 Hr

DATE:

DATE:

SHEET 22

APPLICATION

Humidity

MAX

90%

REV

BABS APRV:

SCALE: NONE

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

Remarks: Notes:

N/A 3 Hr 85 40 120Amercoat 385 -

MIN

50%99 32 120

Flash Point (degrees F)

Temperature (degrees F)

MIN MAX

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time

(DFT)

(6 mil) at 70° F

1:1 8 Hr

PRODUCT INFORMATION

Dimetcote 302H

Dimetcote 302H 417 292 Amercoat 385 176 124

Brush Roller Conv.

Spray

AREA: Bilges SURFACE PREPARATION: 1) Material is to be blasted in wheelabrator to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

2) Prep prior to under coat: Wire brush damaged areas and wipe down entire area with a mild detergent and rinse.

PART

NUMBER

PAINT SYSTEM "I-5"

Airless Spray

Application Method

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

N25 White FULL 7.0 3.0 12 Hr - X 0.021"

Touch Hard 59% N/A 1.5 Hr 6 Hr

DATE:

DATE:

SHEET 23SCALE: NONE

Remarks: Notes:

USCG APRV:

SIZE

A

FSCM CAGE NO

98042

DRAWING NO.

FSV6-631-01

REV

BABS APRV:

-Amercoat 5450 N/A - 108 45 100 -

Flash Point (degrees F)

APPLICATION

Temperature (degrees F) Humidity

MIN MAX MIN MAX

PRODUCT INFORMATION

VOLUME

SOLIDS

CURING

AGENT

Mixed Ratio Base:Cure

Pot Life at 70° F

Drying time at 70° F

Theoretical Practical Fan Amercoat 5450 241 168

PAINT SYSTEM "I-6"

Overcoat Time @ 70° F

Application Method

Brush Roller Conv.

Spray

Airless Spray

Airless Spray

AREA: Exposed insulation in way of aluminum structure, but not type II acoustic insulation.

SURFACE PREPARATION: Wipe clean and allow to dry

PART

NUMBER

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

N14 Terracotta FULL 8.0 5.0 8 Hr - X 0.021" N5 Black FULL 4.0 2.0 6 Hr - X 0.021"

Touch Hard 78% Powder 4 Hr 6 Hr 66% Part B 2 Hr 16 Hr 56% Part B 2 Hr 8 Hr

DATE:

DATE:

SHEET 24

Brush Roller Conv.

Spray

PAINT SYSTEM "M-1"

SYSTEM

INFORMATION

COLOR

TYPE

COAT

WFT

MILS

DFT

MILS

Spread Rate @ Spec.

DFT Sq. Ft. per coat

Overcoat Time @ 70° F

Theoretical Practical

Application Method Airless Spray

Fan

AREA: Anchor SURFACE PREPARATION: 1) Material is to be blasted near white to remove mill scale and oxidation. Any material not suitable for the wheelabrator is to be hand blasted. Blasting is to be finished to specification SSPC-SP10. After blasting all material is to be coated with P/N N23 - International Interplace 937 (Grey) Primer.

PART

NUMBER

Airless Spray

Amercoat 229T 449 337

Dimetcote 302H 417 292 Amercoat 385 212 148

MIN

50%

VOLUME

SOLIDS

CURING

A…