FB Family Housing Replacement SID report.pdf

Structural Interior Design (SID)

U.S. Army Family Housing Replacement

Ft. Buchanan, Guaynabo, Puerto Rico

Project No. W912EP20F0071

August 2020

STRUCTURAL INTERIOR DESIGN

(SID)

TABLE OF CONTENTS

I. Design Analysis

II. Manufacturers' Source List

III. Item Code Descriptions

IV. Product Technical Data

V. Finishes

VI. Reference Drawings

PART I

DESIGN ANALYSIS

U.S. Army Family Housing Replacement Design Analysis Ft. Buchanan, Guaynabo, Puerto Rico Project Number W9127818D0003

3.2 Architectural

3.2.1 Facility Description

The project is to remove and replace the existing 27 Family Housing Unites (FHU) built in the

Coconut Grove community and replace them with 26 new FHU to conform to Army Family Housing

(AFH) standards. The design and construction of new FHU, along with new community amenities will improve the current standards of quality of life, energy conservation, size habitability and safety requirements set for by AFH standards.

The design of the FHU has been influenced by local building standards, climatic constraints, and opportunities. The proposed design consists of detached single-story FHU constructed of concrete masonry units with an insulated exterior weather barrier in order to meet energy requirements, resists the hot and humid climatic conditions and be durable to withstand hurricane resistant winds.

The look of the facilities will have a contemporary look which ties into the historic character of the

FHU to be replaced. Single low sloped concrete roofs with parapet walls will vary in height to help break up the mass of each home. Homes shall vary in finish and color to help create diversity in look without dramatically increasing construction cost.

3.2.1.1 Building Design

The primary objective of this building design is to provide a contextually sensitive design that fits with the Coconut Grove community and existing aesthetic of the existing community. Houses shall consist of an attached two-car garage and three-to-four-bedroom single story home. Primary construction shall consist of concrete masonry units (CMU) and concrete roofing. Exterior finishes shall vary throughout the site but shall consist of non-wood based products and be selected on cost, longevity, durability and ease of construction. The FHU will be designed to withstand up to 160 mph winds.

3.2.1.2 Accessibility

A minimum of five (5) percent of all housing meet all requirements contained in the Architectural

Barriers Act (ABA) Standards (2015) for all portions of the facility. A total of 2 FHU shall meet ABA requirements for residents who require accessibility and require hearing and vision impairments.

The entire site area and facility contained within the limits of this project will be fully accessible to all individuals with disabilities.

3.2.1.3 Codes and Standards

The design of the facility will utilize the most current relevant codes and standards. Reference

Section 3.6 for a list of applicable reference materials and industry criteria.

3.2.1.4 External Activities

Vehicular and pedestrian access will be provided as shown in the proposed site plan included with this PCR (see Appendix E). ABA compatible transitions will be provided at the entry of the facility to gain the elevation from ground to the building.

3.2.1.5 Internal Activities

Internal actives of the FHU is based the prioritization of spaces while limiting the quantity of internal hallways. Common family areas such as the kitchen, great room and dining area are centrally located within the core of the house as to provide central access and exterior windows to the greatest extent possible.

3.2.1.6 Space Allocations

Room sizes and placement are based on minimum spaces as provided in UFC 4 711 01 Family

Housing.

3.2.1.7 Fire Protection

All FHU will comply with IRC and UFC requirements. Unless exempted by the Local Authority

Having Jurisdiction at Ft. Buchanan, each facility will have automatic fire suppression systems.

Also, the ABA accessible units shall meet alarm requirements per the Architectural Barriers Act

Accessibility Standards (ABAAS).

3.2.2 Building Components

Design and construction will comply with and conform to all requirements, brand name references, and standards identified in the most current version of UFC Standards at the time of the design contract award. Preference will be given to regional and recycled (or high recycled content) materials, which creates a synergy within the LEED system.

The Government desires low or no maintenance finish materials to the greatest extent possible. The proposed building systems and material finishes will conform to the minimum requirements and allowable options contained within each of the applicable UFGS specification sections.

3.2.2.1 Concrete

Requirements for the structural system are contained in the Structural Section 4.3 of this report. An under-slab vapor barrier is required to prevent moisture from damaging or delaying the installation of floor finish materials.

3.2.2.2 Concrete Masonry Units

Exterior walls are constructed with 8” thick typical concrete masonry units, with spray foam insulation in open cells. Interior walls are constructed with 6” thick typical concrete masonry units.

3.2.2.3 Metals

Metal finish appearance shall be selected based on similarity of use within the Ft Buchanan

Installation and provide a visual character of unity. All miscellaneous ferrous metal items, exposed to view, which do not have a factory finish, will be primed and painted. Louvers will have bird or insect screens as appropriate.

3.2.2.4 Stairs

Not applicable.

3.2.2.5 Wood

Due to termites the use of wood is limited to cabinets, interior doors, unexposed roofing nailers, shims, and backing for flashing.

3.2.2.6 Built-In Cabinets

Cabinets shall be AWl custom grade at a minimum. The finished material of exposed fronts and ends of cabinets, door and drawer fronts shall be wood grade veneer, at minimum. Rapidly renewable materials will be encouraged for cabinetry materials.

Countertops will be solid surface with field applied back splashes will be used at the kitchen and laundry areas. Cultured marble will be part of the vanity counter surface in restroom areas.

3.2.2.7 Thermal and Moisture Protection

A full air barrier assembly will be provided as part of the exterior envelope.

Exterior walls shall be of insulated concrete masonry units with a textured direct applied exterior finish system (DAEFS) with a silicon enhanced finish coat system with mildewcide. Exterior grade paint shall be applied to all exterior surfaces not receiving a DAEFS system such as Dryvit TAFS.

Spray foam may be used at the interior side of furred exterior walls to form a continuous layer of insulation that provides part of an air barrier. Conform to requirements of IBC for separating foam insulation from interior exposure. Air barrier conformance shall be demonstrated using test procedures per U.S. Army Corps of Engineers Air Leakage Test Protocol for Building Envelopes.

3.2.2.8 Roofing System

The exterior roof will be fluid applied waterproof acrylic coating system cool roof coating system with a reinforced fabric membrane. Roof system shall meet wind uplift requirements per the IBC and

ASCE7 and installation standards in Puerto Rico.

3.2.2.9 Doors

Door hardware shall be per the Ft Buchanan Standards and will be residential grade.

All exterior doors must meet AT/FP requirements and shall be designed to meet wind-borne debris protection and fastening per code. Additionally, all exterior doors are expected to comply with

Miami-Dade Notice of Acceptance (NOA) and pass large and small projectile testing. AT/FP may override NOA requirements where no other option exists.

The main entrance door and exterior doors will be an aluminum to withstand high humidity conditions. Doors between conditioned and unconditioned areas shall be insulated. Hollow metal doors will be used for doors leading into the garage.

Interior doors will panel solid core, with a veneer, for durability. Doors shall comply with AWI custom grade performance specifications for all doors. All interior door hardware will be brushed stainless steel finish.

3.2.3 Windows

Typical windows will be a manufacturer's standard type, aluminum, double-glazed, tinted, insulated low-E coated product whose thermal performance complies with the U.S. Department of Energy requirements. Windows shall have a removable hurricane fabric protection system, to protect from wind born debris during a hurricane storm event meeting the minimum construction requirements for air infiltration, water penetration, STC rating, and condensation indices.

3.2.4 Flooring Finishes

All floor finishes will be selected for durability, ease of maintenance, and the ability to replace only a part of the finish if necessary.

3.2.4.1 Carpet

Carpet tile will not be used

3.2.4.2 Concrete

Sealed concrete floors will be provided in the exterior storage room and garage.

3.2.5 Interior Wall Finishes

3.2.5.1 CMU Walls:

Interior walls will be a cmu wall system with a Level 5 plaster coat finish. Walls shall be painted to as indicated on the drawings.

3.2.5.2 Gypsum Board:

Painted cement board will be limited as chases to conceal ducts only and will be used sparingly.

Colors and textures will match the wall finish.

3.2.5.3 Wall Base

Base and crown molding will be a pre-finished PVC base molding.

3.2.5.4 Ceramic Tile

Porcelain tile finishes on the walls in the kitchen and restrooms floor and shower areas. Tiled and shower areas will have ceramic tile over cementitious backer board.

3.2.6 Ceilings

A plaster finish over cast-in-place concrete will be utilized throughout most of the FHU. Finish shall be smooth finish with low sheen or semi-gloss paint.

3.2.7 Paint

Interior surfaces, except factory pre-finished material or interior surfaces receiving other finishes, shall be painted a minimum of one prime coat and two finish coats. Provide an MPI Gloss Level 5

Finish (Semi-gloss) in wet areas and a satin finish in all other areas.

Paints and coating products shall be classified as containing low or zero volatile organic compounds

(VOCs) in accordance with MPI criteria.

3.2.7.1 Toilet Accessories

Toilet fixtures shall be residential grade. All toilet and bath accessories shall use 316L stainless steel fasteners. All accessories including but not limited to grab bars, towel bars and toilet tissue shall be residential grade.

Mounting for accessories shall be directly into cmu interior walls with concrete type anchors. Wood backing shall not be used.

3.2.7.2 Signage

Not required.

3.2.8 Equipment

Microwaves, refrigerators, ranges, ovens, dishwashers, and range hoods will be residential grade.

Accessible ranges, ovens mounted at ABA height in ABA accessible residences. Bathroom vanities consisting of cabinetry, sinks and countertops will be provided as a single unit.

PART II

MANUFACTURERS' SOURCE LIST

MANUFACTURER

DALTILE

1119 ARION PARKWAY

SAN ANTONIO, TEXAS 78216

PHONE: 800-449-3591

FLORIDA TILE

998 GOVERNORS LANE, SUITE 300

LEXINGTON, KY 40513

PHONE: 859-219-5200

PPG

ONE PPG PLACE

PITTSBURGH, PENNSYLVANIA 15272

PHONE: 412-434-3131

SHERWIN WILLIAMS

101 W. PROSPECT AVE.

CLEVELAND, OH 44115

PHONE: 1-800-474-3794

WILSONART

2501 WILSONART DRIVE

P.O. BOX 6110

TEMPLE, TEXAS 76503-6110

PHONE: 800-433-3222

CANARM

2157 PARKEDALE AVE.

PO BOX 367

BROCKVILLE, ONTARIO CANADA

U.S. Army Family Housing Replacement

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

MANUFACTURERS' SOURCE LIST

The manufacturer's names and their products referenced indicate the color, type, and quality of product required. The products furnished shall meet the color, type, and quality indicated. All product substitutions must be approved by the client.

DEALER/VENDOR

JULIE CARCANAGUES, A&E REP

PHONE: 210-842-5859

EMAIL: JULIE.CARCANAGUES@DALTILE.COM

BLAKELEY DENT, REP

PHONE: (210) 981-2569

EMAIL: CS@FLORIDATILE.COM

TINA MARTI, A&D REP

PHONE: 210-439-1512

EMAIL: TMARTI@PPG.COM

JOY I BABUR, ARCHITECTURAL REP

PHONE: 281-904-5292

EMAIL: JOY.I.BABUR@SHERWIN.COM

ZANE LAND, ARCHITECTURAL REP

PHONE: 830-431-3298

EMAIL: LANDZ@WILSONART.COM

HOME DEPOT

PHONE: 770-384-4646/ 1-877-946-9843

EMAIL: CUSTOMER_CARE@HOMEDEPOT.COM

MANUFACTURER

IVY HILL TILE

INDESIGN CEMENTINE

DECO MIRROR

SEAGULL LIGHTING

7400 LINDER AVE

SKOKIE, IL 60077

PHONE 800.347.5483

WYNDHAM COLLECTION

1175 AVIATION PLACE

SAN FERNANDO, CA 91340

PHONE: 1-888-522-8476

KOHLER

444 HIGHLAND DRIVE

KOHLER, WI 53044

PHONE: 1-800-456-4537

FRESCA

PHONE: 347-402-1053

HUNTER FAN CO

180 THREET INDUSTRIAL RD #120

SMYRNA, TH 37167

PHONE: 1-888-830-1326

KRAUS

12 HARBOR PARK DRIVE

PORT WASHINGTON, NY 11050

PHONE: 1-800-775-0703

BOOTZ

1400 PARK STREET

EVANSVILLE, IN 47719-1010

PHONE 8112.423.5401

U.S. Army Family Housing Replacement

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

MANUFACTURERS' SOURCE LIST (CONTINUED)

The manufacturer's names and their products referenced indicate the color, type, and quality of product required. The products furnished shall meet the color, type, and quality indicated. All product substitutions must be approved by the client.

DEALER/VENDOR FOR ALL MANUFACTURERS

HOME DEPOT

PHONE: 770-384-4646/ 1-877-946-9843

EMAIL: CUSTOMER_CARE@HOMEDEPOT.COM

MUSTEE

5431 WEST 164TH ST

BROOK PARK, OH 44142

PHONE 216.267.9977

MANUFACTURER CONTINUED:

PFISTER

19701 DaVINCI

LAKE FOREST, CA 92610

PHONE: 1.800.732.8238

GLACIER BAY

PHONE: 855.434.5224

GE APPLIANCES

4000 BUECHEL BANK RD

LOUISVILLE, KY 40218

PHONE: 800.626.2005

SHARP APPLIANCES

SHARP PLAZA

MAHWAH, NJ 07495

PHONE: 800.BE.SHARP

GATCO

1550 FACTOR AVE.

SAN LEANDRO, CA 94577

PHONE: 800.227.5640

AQUA EDEN-KINGSTON BRASS

12775 RESERVOIR ST.

CHINO, CA 91710

PART III

ITEM CODE DESCRIPTIONS

Family Housing Replacement

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

ITEM CODE DESCRIPTIONS

The manufacturer's names and their products referenced indicate the color, type, and quality of product required. The products furnished shall meet the color, type, and quality indicated. All product substitutions must be approved by the client.

RESTROOM PLUMBING FIXTURES

L-1 1 LIGHT FIXTURE, BRAND: SEA GULL LIGHTING, HETTINGER CO: BRUSHED

NICKEL, DIMS: 4.5"W X 8"H, MODEL#: 4139101-962

L-2 2 LIGHT FIXTURE, BRAND: SEA GULL LIGHTING, HETTINGER CO: BRUSHED

NICKEL, DIMS: 13.5" X 8"H, MODEL#: 4439102-962

M-1 MIRROR, BRAND: DECO MIRROR SPECTRUM METAL FRAMED WALL MIRROR

CO: B. NICKEL 22X34, MODEL #8775

V-1 KOHLER ARCHER VITREOUS CHINA PEDESTAL COMBO BATHROOM SINK:

SINGLE HOLE, OVERFLOW DRAIN COLOR: WHITE, MODEL: K-2359-1-0

V-2 WYNDHAM COLLECTION: SHEFFIELD 36"W X 22"D VANITY IN GRAY WITH

CULTURED CARRARA WHITE MARBLE TOP WITH WHITE BASIN, MODEL:

WCS141436SGYCMUNOMXX

V-3 WYNDHAM COLLECTION:BECKETT 60"W X 22"D DOUBLE BATH VANITY IN

DARK GRAY WITH CULTURED CARRARA WHITE MARBLE TOP WITH WHITE BASIN,

MODEL: WCG242460DKGCCUNSMXX

V-4 WYNDHAM COLLECTION: SHEFFIELD 72"W X 22"D VANITY IN GRAY WITH

CULTURED CARRARA WHITE MARBLE TOP WITH WHITE BASINS, MODEL:

WCS141472DGYCMUNSMXX

V-5 FRESCA TORINO 12"W X 15"D X 68"H BATHROOM LINEN STORAGE TOWER

CABINET IN GRAY, MODEL: FST6260GR

FX-1 KOHLER AWAKEN 3-SPRAY HANDSHOWER KIT W/ SLIDEBAR & HOSE

K-98361-G-BN CO:BRUSHED NICKEL + HANDHELD ELBOW K-98351-BN + COMPONETS

VOLUME CONTROL VALVE TRIM WITH LEVER HANDEL K-T78025-4

FX-2 PFISTER VENTURI 4" CENTERSET SINGLE HANDLE SINGLE FAUCET CO: SPOT

DEFENSE BRUSHED NICKEL ITEM: LF-042-VNGS

FX-3 PFISTER VENTURI 8" WIDESPREAD 2-HANDLE BATHROOM FAUCET CO: SPOT

DEFENSE BRUSHED NICKEL ITEM: LF-049-VNGS

FX-4 AKDY 1-HANDLE FREESTANDING FLOOR MOUNT TUB FAUCET BATHTUB

FILLER WITH HAND SHOWER, CO: BRUSHED NICKEL MODEL: TF0047

FX-5 KOHLER 1-HANDLE 3-SPRAY TUB & SHOWER FAUCET, CO: BRUSHED NICKEL

MODEL: #K-R78040-4E-BN

BT-1 BOOTZ INDUSTRIES ALOHA 60" RIGHT DRAIN RECTANGULAR ALCOVE

SOAKING BATHTUB: COLOR: WHITE ITEM: 011-4365-00

Family Housing Replacement

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

ITEM CODE DESCRIPTIONS

The manufacturer's names and their products referenced indicate the color, type, and quality of product required. The products furnished shall meet the color, type, and quality indicated. All product substitutions must be approved by the client.

RESTROOM PLUMBING FIXTURES CONTINUED

BT-2 BOOTZ INDUSTRIES ALOHA 60" LEFT DRAIN RECTANGULAR ALCOVE

SOAKING BATHTUB: COLOR: WHITE ITEM: 011-4368-00

BT-3 KOHLER, EXPANSE 60" RIGHT HAND DRAIN AVLOVE BATHTUB WITH

INTEGRAL FLANGE, COLOR: WHITE, MODEL #K-118-RA-0 + CLEARFO BATH DRAIN

CO: BN MODEL: K-7213-BN

BT-4 AQUA EDEN, ARIA 60" ACRYLIC PEDESTAL FLATBOTTOM FREESTANDING

BATHTUB, COLOR: WHITE MODEL# HVTSQ602824

BT-5 KOHLER, EXPANSE 60" LEFT HAND DRAIN AVLOVE BATHTUB WITH

INTEGRAL FLANGE, COLOR: WHITE, MODEL #K-118-LA-0 + CLEARFO BATH DRAIN

CO: BN MODEL: K-7213-BN

T-1 GLACIER BAY, 1-PIECE 1.1 GPF HIGH EFFICIENCY DUAL FLUSH ELONGATED

ALL IN ONE TOLIET, COLOR: WHITE, MODEL: N2420

S-2 NAMEEKS, MARS WALL MOUNTED CERAMIC BATHROOM SINK, CENTER

HOLE, COLOR: WHITE, MODEL#: TECLA MAR02011-ONE HOLE

SR-1 ZENNA HOME, RUSTPROOF STAINLESS STEEL DUAL MOUNT CURVED

SHOWER ROD, COLOR: BRUSHED NICKEL, MODEL # 72S1STBNL

SR-2 BARCLAY PRODUCTS, 36" STRAIGHT SHOWER ROD, COLOR: BRUSHED

NICKEL, MODEL #4100-36-BN

TB-1 GATCO, ELEVATE 18" TOWEL BAR, COLOR: SATIN NICKEL MODEL #4071

TB-2 GATCO, ELEVATE 24" TOWEL BAR, COLOR: SATIN NICKEL, MODEL #4070

TB-3 GATCO, ELEVATE TOWEL RING, COLOR: SATIN NICKEL, MODEL #4072

TB-4 GATCO, ELEVATE STANDARD DOUBLE POST TOILET PAPER HOLDER,

COLOR: SATIN NICKEL, MODEL #4073A

GB-1 GATCO, ELEVATE 24" GRAB BAR, COLOR: SATIN NICKEL, MODEL #954

GB-2 GATCO, ELEVATE 36" GRAB BAR, COLOR: SATIN NICKEL, MODEL #956

GB-3 GATCO, ELEVATE 48" GRAB BAR, COLOR: SATIN NICKEL, MODEL #960

BC-1 MUSTEE, CAREGIVER 23"W X 14.2" D FOLD DOWN SHOWER SEAT IN WHITE

MODEL# 390.413

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

ITEM CODE DESCRIPTIONS

The manufacturer's names and their products referenced indicate the color, type, and quality of product required. The products furnished shall meet the color, type, and quality indicated. All product substitutions must be approved by the client.

KITCHEN PLUMBING FIXTURES

F-1 KRAUS, NOLA COMMERCIAL STYLE SINGLE-HANDLE PULL-DOWN SPRAYER

KITCHEN FAUCET WITH DUAL FUNCTION FINISH: STAINLESS STEEL MODEL:

#KPF-1640SS

S-1 KRAUS, STANDART PRO 3" 16 GUAGE UNDERMOUNT 50/50 DOUBLE BOWL

STAINLESS STEEL MODEL#KHU102-33

H-1 GE 30" WALL MOUNT RANGE HOOD W/ LED LIGHT + VENT EXTENSION

COVER, FINISH: STAINLESS STEEL, MODEL: UVW8301SLSS + UX12DC83SS

ST-1 GE 30IN 5.3CUFT SLIDE IN ELECTRIC RANGE WITH SELF CLEANING OVEN,

FINISH: STAINLESS STEEL MODEL#JS645SLSS

R-1 GE 25.1 cu. ft. Side by Side Refrigerator in Fingerprint Resistant Stainless Steel, MODEL: GSS25IYNFS

DW-1 GE TOP CONTROL TALL TUB DISHWASHER, FINISH: STAINLESS STEEL

MODEL#GDT530SP

DW-2 GE 24" DISHWASHER W/ INTERIOR STAINLESS STEEL, ADA COMPLIANT

DIMS: 32.25"H X 22"W X 24"D, MODEL#GDT225SSLSS

M-1 SHARP 24"W 1.2CU FT BUILT IN MICROWAVE DRAWER FINISH: STAINLESS

STEEL MODEL#KB6524PSY

WS-1 GE 4.8 cu. ft. Smart Satin Nickel Front Load Washing Machine with UltraFresh Vent System and OdorBlock, ENERGY STAR #GFW650SPNSN (BASIS OF DESIGN, TENANT

SUPPLIED)

DR-1 7.8 cu. ft. Smart 240-Volt Satin Nickel Stackable Electric Vented Dryer with Steam and Sanitize Cycle, ENERGY STAR MODEL# GFD65ESPNSN (BASIS OR DESIGN, TENANT SUPPLIED)

SH-1 ClosetMaid Closet Mesh 72 in. x 16 in. Ventilated Wire Shelf (CUT TO LENGHT AS

NEEDED) MODEL #4735 + (FOR CLOSETS MODEL #5629 + #2058)

CEILING FAN

FAN-1 HUNTER BECK 42' LED BRUSHED NICKEL CEILING FAN WITH LIGHT KIT

MODEL# 53432

FAN-2 HUNTER BECK 52" LED BRUSHED NICKEL CEILING FAN WITH LLIGHT KIT

MODEL#54214

PART IV

PRODUCT TECHNICAL DATA

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

PRODUCT TECHNICAL SHEETS

L-1 SINGLE WALL SCONCE

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

L-2 DOUBLE WALL SCONCE

Installation Instructions for

Hettinger 1, 2, 3, and 4 Light Wall 1.0

990W4_3910_-HET

4139101, 4439102, 4439103, 4439104

Wall

NEED HELP?

NECESITA AYUDA?

AVEZ VOUS BESOIN AIDE- D’ ?

If you need installation assistance, replacement parts, or have questions regarding our warranty, please call our customer care center:

Si necesita asistencia en la instalación, piezas de repuesto, o tiene preguntas acerca de nuestra garantía, por favor llame a nuestro centro de servicio al cliente:

Si vous avez besoin de pièces de rechange, d 'aide pur l'installation ou si vous avez des questions concernant notre garantie, veuillez appeler nos conseillers en produits au :

STOP

ARRÊTER

ALTO

SAVETHESE INSTRUCTIONS!

1-800-347-5483 To register your fixture, please visit our website:

www.SeaGullLighting.com

SAVETHESE INSTRUCTIONS!

Warranty

Sea Gull Lighting fixtures and components, when properly installed and under normal conditions of use, are warranted to be free from defects in materials and workmanship for one year from date of sale. light sources are warranted for five years. ® labeled products are warranted for three years.LED ENERGY STAR Sea Gull Lighting at its sole option will repair or replace, F.O.B. Factory, freight prepaid, any Sea Gull Lighting product defective in materials or workmanship.

Such replacement is the exclusive remedy against Sea Gull Lighting should any of the products delivered prove defective. Invoices for labor charges and/or charge backs for labor will be denied unless prior written approval is given.

Any modification to a Sea Gull Lighting product not made at the factory will void the or listing as well as the Sea Gull Lighting warranty policy.UL ETL

To register your fixture, please visit our website: SeaGullLighting.com

Garantie

A la condition d'un montage et d'une utilisation dans les normes, les Luminaires et pièces Sea Gull Lighting sont garantis sans défauts des matériaux et dans leur fabrication pour une durée d'un an à compter de la date d'achat. Sources de lumière sont garantis pour cinq ans. Les produits labellisés ®LED ENERGY STAR sont garantis pour trois ans.A sa seule discrétion, Sea Gull Lighting réparera ou remplacera tout produit Sea Gull Lighting défectueux dans ses matériaux ou dans sa fabrication, F.O.B. Usine fret payé d'avant. Un remplacement selon ces conditions est l'unique recours à l'encontre de Sea Gull Lighting dans le cas où les produits livrés se révèlent défectueux.Toute facture concernant des frais de main d'oeuvre et/ou toute demande de remboursement de main d'oeuvre sera rejetée à moins qu'un accord écrit ait été consenti au préalable.

Toute modification non effectuée par l'usine d'un produit Sea Gull Lighting conduira à l'annulation des enregistrements ou ainsi que du contrat deUL ETL garantie Sea Gull Lighting.

Pour enregistrer votre luminaire, veuillez consulter notre site web : SeaGullLighting.com

Garantía

Los accesorios y componentes Sea Gull Lighting, cuando son correctamente instalados bajo condiciones de uso normal, se garantizan a estar libres de defectos en materiales y trabajo manual por un año de la fecha de compra. Lámparas tienen una garantía de cinco años. Los productos etiquetados ®LED ENERGY STAR se garantizan por tres años. Sea Gull Lighting a su propia opción reparará o reemplazará, F.O.B. Factory, flete pre pagado, cualquier producto de Sea Gull Lighting defectuoso en materiales o trabajo manual.Tal reemplazo es el remedio exclusivo en contra de Sea Gull Lighting en caso de que cualquiera de sus productos entregados esté defectuoso. Facturas por cargos de labor y/o cargos al usuario por labor serán negados a menos de que se haya recibido permiso previo por escrito.

Cualquier modificación hecha a un producto de Sea Gull Lighting no llevado a cabo en la fábrica anulara el listado de o al igual que la póliza de garantía de Sea Gull Lighting.UL ETL

Para registrar su accesorio, por favor visite nuestra página web: SeaGullLighting.com

G P I :ENERAL RODUCT NFORMATION

These fixtures are intended to be installed utilizing compliant junctionNEC boxes.

This product is safety listed for damp locations.

Incandescent version may be dimmed with a standard incandescent dimmer.

LED LEDversion may be dimmed with a dimmer. Consult lamp manufacturer for additional information.

This instruction shows a typical installation.

CAUTION RISK OF FIRE-

This product requires installation by a qualified electrician.

Before installing be sure to read all instructions and

TURNTHE POWERTOTHE ELECTRICAL BOX OFF.

MISE EN GARDE RISQUE INCENDIE- D'

Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents

Les fils d’alimentation doivent convenir pour 90°c.

ADVERTENCIA RIESGO DE INCENDIO-

Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.

Conductores de alimentacion 90°c Min.

CAUTION RISK OF FIRE-

This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.

Use minimum 90°c supply conductors.

L1 & L2

1A

Secure the mounting plate to the junction box.

Connect the fixture to a suitable ground in accordance with local electrical codes.

Connect the white fixture wire to the neutral power line wire with a wire nut.

Connect the black fixture wire to the hot power line wire with a wire nut.

Align, then place the fixture base onto the mounting plate stud (s) and secure it with the cap nut (s).

Place the shade and spacer over the socket and onto the shade base, then secure them in place by screwing the collar nut onto the socket using the shade tool. Repeat for remaining shades.

Screw the lamp(s) into the socket(s). Refer to the label on the socket for Max Wattage Information.

Install the Fixture

JUNCTION BOX

NEUTRAL WIRE

HOT WIRE

WHITE WIRE

BLACK WIRE

MOUNTING

PLATE STUD

CAP NUT

MOUNTING

PLATE

SHADE TOOL

SHADE

SOCKET

SHADE BASE

COLLAR NUT

SPACER

Fixez la plaque de montage à la boîte de jonction.

Connectez le luminaire à un terrain approprié conformément aux codes électriques locaux.

Connectez le fil blanc de luminaire au fil de ligne à neutre avec un écrou de fil.

Connectez le fil noir de luminaire au fil ligne électrique chaud avec un serre-fils.

Aligner, puis placez le base de luminaire sur la/les goujon (s) de montage et le fixer avec les écrou (s) capuchon.

Placez l’abat-jour et l'espaceur sur la douille et sur la base de l’abat-jour, puis fixez-les en place en vissant l'écrou de collier sur la douille en utilisant l'outil de l’abat-jour. Répétez l'opération pour l’abat-jours restants.

Visser l’ampoule (s) dans la douille (s). Reportez-vous à l'étiquette sur le socket pour Max Puissance information.

Installer le Luminaire

GOUJON

DE MONTAGE

BOITE DE JONCTION

FIL NEUTRE

FIL BLANC

FIL NOIR

PLAQUE DE

MONTAGE

FIL CHAUD

ECROU

CAPUCHON

ABAT-JOUR

DOUILLE

BASE D’ABAT-JOUR

ESPACEUR

ECROU DE COLLIER

OUTIL D’ABAT-JOUR

ENCHUFE

7400 Linder Ave, Skokie, 60077IL

800.323.3226 - 847.626.6300 www.SeaGullLighting.com

© 2017 Sea Gull Lighting.All rights reserved.The "Sea Gull Lighting" graphic is a registered trademark of Sea Gull Lighting. Sea Gull Lighting reserves the right to change specifications for product improvements without notification.

A Generation Brands Company

Fije la placa de montaje a la caja eléctrica con dos tornillos de la placa de montaje.

Conecte la lámpara a una puesta a tierra adecuada de acuerdo a los códigos eléctricos locales.

Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con una tuerca de cable.

Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con una tuerca de cable.

Alinee y coloque la base de la lámpara en el/los esparrago (s) de montaje y fíjela con la/las tuerca (s) capuchon.

Coloque la pantalla y el espaciador sobre el enchufe y sobre la base de la pantalla, y luego asegurarlas en su lugar enroscando la tuerca de collar en el enchufe usando la herramienta de la pantalla. Repita para las pantallas restantes.

Atornille la(s) bombilla(s) en la/los enchufe(s). Consulte la etiqueta en la toma de Max Información Potencia.

CAJA DE

JUNCTURA

CABLE NEUTRO

CABLE BLANCO

ESPARRAGO DE

MONTAJE

CABLE CALIENTE

CABLE NEGRO

PLACA DE

MONTAJE

Instale la Lámpara

TUERCA

CAPUCHON

PANTALLA

BASE DE LA PANTALLA

ESPACIADOR

TUERCA DE COLLAR

HERRAMIENTA DE LA PANTALLA

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

M-1 MIRROR

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

V-1 PEDESTAL SINK

Features

• Vitreous china

• With overflow

• 8″ (20.3 cm) centers (-8), 4″ (10.2 cm) centers (-4), or single-hole (-1)

• Includes installation hardware

• 24″ (61 cm) x 20-1/2″ (52.1 cm) x 35-1/4″ (89.5 cm)

Codes/Standards Applicable Specified model meets or exceeds the following:

• ASME A112.19.2/CSA B45.1

PEDESTAL LAVATORY

K-2359

Colors/Finishes

• 0: White

• Other: Refer to Price Book for additional colors/finishes

Accessories:

• CP: Polished Chrome

• Other: Refer to Price Book for additional colors/finishes

Specified Model

Model Description Colors/Finishes K-2359-8 8″ (20.3 cm) centers pedestal lavatory (shown) ❑ 0 ❑ Other_____ K-2359-4 4″ (10.2 cm) centers pedestal lavatory ❑ 0 ❑ Other_____ K-2359-1 Single-hole pedestal lavatory ❑ 0 ❑ Other_____

Recommended Accessories K-7605-P Lavatory supplies 3/8″ (pair) ❑ CP ❑ Other_____ K-8998 Adjustable P-Trap ❑ CP ❑ Other_____

Product Specification:

The pedestal lavatory shall be made of vitreous china. Pedestal lavatory shall be 24″ (61 cm) in length, 20-1/2″ (52.1 cm) in width, and 35-1/4″ (89.5 cm) in height. Pedestal lavatory shall have 8″ (20.3 cm) centers (-8), 4″ (10.2 cm) centers (-4), or single-hole (-1). Pedestal lavatory shall be with overflow and include installation hardware. Pedestal lavatory shall be Kohler Model K-2359-_______-_______.

ARCHERTM

1063452-4-C

USA/Canada: 1-800-4KOHLER (1-800-456-4537) www.kohler.com

V-1

Technical Information

Fixture*:

Basin area 16-1/4″ (41.3 cm) x 11-15/16″ (30.3 cm) Water depth 4″ (12.7 cm) Drain hole 1-3/4″ (4.4 cm) D.

* Approximate measurements for comparison only.

Included components:

Lavatory basin, 8″ (20.3 cm) centers OR K-2358-8 Lavatory basin, 4″ (10.2 cm) centers OR K-2358-4 Lavatory basin, single-hole K-2358-1 Pedestal K-2357 Pedestal hardware pack 1047155 Rubber pads 63069

Holes K-2359-8 K-2359-4 K-2359-1 Spout 1-3/8″

(3.5 cm) D.

1-1/4″ (3.2 cm) D.

1-3/8″ (3.5 cm) D.

Faucet 1-3/8″ (3.5 cm) D.

1-1/4″ (3.2 cm) D.

Installation Notes Install this product according to the installation guide.

23-15/16" (60.8 cm)

1/2" (1.3 cm) D.

Mounting hole in pedestal

10-1/4" (26 cm)

13-13/16" (35.1 cm)

8" (20.3 cm)

11-1/8" (28.3 cm)

2-5/8" (6.7 cm)

9-1/2" (24.1 cm)

35-1/4" (89.5 cm)

7-1/2" (19.1 cm)

Finished Floor

2-5/8" (6.7 cm)

7-15/16" (20.2 cm)

3/8" Cold

1-1/2" (3.8 cm)

20-7/16" (51.9 cm)

4" (10.2 cm)

K-2359-4K-2359-8

3/8" Hot

4" (10.2 cm)

1-1/4" OD

Finished Wall

2-5/8" (6.7 cm)

K-2359-1

Product Diagram

ARCHERTM

ARCHERTM PEDESTAL LAVATORY

1063452-4-C

V-1

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

V-2 36" VANITY

WC-1414-36

TOP VIEW OF VANITY CABINET

36”

15-1/2”

3-1/4”

-3

/4

6- 1/

4”

36”

2-1/2”

5”

8”9”

22"

3”

36"

35"

-1

/2

3-1/2"

8-1/4”

*Note: All Measurements are ± 1/4”

V-2

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

V-3 60" VANITY

WC-1414-72

Double Vanity

TOP VIEW OF VANITY CABINET

*Note: Due to high probability of breakage, the backsplash comes in two pieces, cut from same piece. All measurements are ± 1/4”.

72”

3”

3-1/2”

22”

71”

-1

/2

72”

5” 2-1/2”

8-1/4”

72”

3-1/4”

17” 6-

1/ 4”

-1

/4

16”

40”

16”

9” 8”

40”

V-3

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

V-4 72" VANITY

WC-2424-60-DBL

*Note: Due to high probability of breakage, the backsplash comes in two pieces, cut from the same piece. All measurements are ±1/4”.

13" 34" 60"

13"

9" 6-1/4"

-1

/4

4 1/2"

3-1/4"

4-1/2"

17" 17" 17"

4-1/2"

12-1/2"

15"

59"

19-3/4" 14-1/2" 19-3/4"

-1

/2

-1

/4

19-1/2" 14-1/4" 19-1/2"

-3

/4

6"

9-1/2" 9-1/2"

TOP VIEW OF VANITY CABINET

13"

6"

60"

3"

22"

3/4"

V-4

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

V-5 LINEN CABINET

V-5

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

FX-1 HANDSHOWER AND VALVE

• Handshower features contemporary design.

• Advanced spray engine provides three spray functions: wide coverage, intense drenching, and targeted spray.

• Wide coverage spray produces an encompassing spray for everyday use.

• Intense drenching spray delivers a forceful spray ideal for rinsing soap from hair.

• Targeted spray is a focused stream for targeting sore muscles or use as a utility spray.

• Thumb tab allows for a smooth transition between sprays.

• Spray nozzles cover full area of sprayhead.

• Combination of balance, weight, grip, and angle makes this handshower comfortable and easy to use.

OBC

• MasterClean™ sprayface is easy to clean.

• 1.75 gpm (gallons per minute) flow rate.

• 24-inch slidebar features adjustable mounting brackets for installation flexibility.

Codes/Standards

Material ASME A112.18.1/CSA B125.1• KOHLER finishes resist corrosion and tarnishing. DOE - Energy Policy Act 1992

Water Conservation & Rebates EPA WaterSense®

California Energy Commission (CEC)• WaterSense®-labeled 1.75-gpm handshowers use up to 30 percent less water than standard 2.5-gpm handshowers, while still meeting strict performance guidelines.

OBC

KOHLER® Faucet Lifetime Limited Warranty

• This product can help a building earn Water Efficiency points in the LEED® Green Building Rating System.

See website for detailed warranty information.

Components

Additional included component/s: 60-inch ribbon hose.

Available Color/Finishes Color tiles intended for reference only.

DescriptionCodeColor

Polished ChromeCP

Vibrant® Brushed NickelBN

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current Specification Sheet, go to www.kohler.com.

9-28-2018 15:30

Awaken® G90 Slidebar Kit K-98361-G

FX-1

http://www.kohler.com

Ø 3-9/16"

NotesTechnical Information Install this product according to the installation instructions.

All product dimensions are nominal.

Handshower:

Plumbing codes require approved backflow prevention devices to be installed in-line to1.75 gal/min (6.6 l/min)Rated maximum flow:

handshowers. Please consult with local plumbing officials.

Mount the slidebar to stud framing or install backing support. For tile or other solid finish surfaces: Predrill mounting holes through surface material only; do not drill into the stud. For drywall surface: No predrill is required.

NOTE: The mounting brackets can be adjusted to align with existing holes for retrofit installations.

OBC compliant when installed to the specific requirements of these regulations.

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current Specification Sheet, go to www.kohler.com.

9-28-2018 15:30

Awaken® G90 Slidebar Kit K-98361-G

• Single Lever handle allows for simultaneous on/off activation and temperature setting.

• Coordinates with Components faucets and accessories to complete your bathroom.

Material

• Premium material construction with metal handle ensures reliability and durability.

• KOHLER finishes resist corrosion and tarnishing.

Technology

• Patented K-joint installation technology ensures consistent trim appearance, regardless of variability in valve rough-in.

Required Products/Accessories K-2974-K 1/2" Volume Control Valve

CSA B651 OBC

Codes/Standards or K-2977-K 3/4" Volume Control Valve ASME A112.18.1/CSA B125.1

ADA

Recommended Products/Accessories

K-23723 Faucet cleaner

ICC/ANSI A117.1

CSA B651

OBC

KOHLER® Faucet Lifetime Limited Warranty See website for detailed warranty information.

Available Colors/Finishes Color tiles intended for reference only.

DescriptionCodeColor

Polished ChromeCP

Vibrant® Brushed NickelBN

Matte BlackBL

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current Specification Sheet, go to www.kohler.com.

3-22-2020 10:58 - US/CA/LM/MX

Components™ volume control valve trim with Lever handle K-T78025-4

• For use with a handshower and hose (sold separately).

• Coordinates with Awaken showerheads, handshowers and showering accessories.

• Easy installation using slip fit connection.

• Includes check valve.

Material

• Metal construction.

• KOHLER finishes resist corrosion and tarnishing.

Installation

• Wall-mount

For complete listing of available colors, go to kohler.com.

Codes/Standards

ASME A112.18.1/CSA B125.1

ASSE 1014

KOHLER® Faucet Lifetime Limited Warranty See website for detailed warranty information.

Product Specification Supply elbow shall be 2-5/16” (59 mm) in length, 2” (51 mm) in width, and 2-1/4” (57 mm) in height.

Supply elbow shall be of metal construction.

Supply elbow shall include check valve. Supply elbow shall be for wall-mount installation. Supply elbow shall be KOHLER Model K-98351.

USA/Canada: 1-800-4KOHLER (1-800-456-4537) www.kohler.com 1-28-2014 08:06

Awaken™

Wall-mount Supply Elbow with Check Valve K-98351

FX-1

G1/2-14

Installation Notes Install this product according to the installation guide.

IMPORTANT! Verify and ensure the "A" dimension (from the supply elbow to the finished wall surface).

USA/Canada: 1-800-4KOHLER (1-800-456-4537) www.kohler.com 1-28-2014 08:06

Awaken™

Wall-mount Supply Elbow with Check Valve K-98351

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

FX-2 4"CENTERSET SINGLE FAUCET

Dimensions

Specifications

Features Code Compliance

Venturi™ Single Control Lavatory Faucet

LF-042-VNBB Finish(BB)q LF-042-VNCC Finish(CC)q LF-042-VNKK Finish(KK) q

• 1 or 3-Hole Installation

• Pforever Seal

• Push & Seal™ Pop-Up

• 1.2 GPM Flow Rate

• 1 or 3-Hole Installation;

Deck Plate or Single Hole Mounting Option

• Unique Ribbon Water Flow Pattern

• All Metal Construction

• Mounting Hardware

Included

• Mounting Posts

• Pfast Connect

• PVD Finish (KK Finish Only)

• Push & Seal™ Pop-Up

• TiteSeal™ Deckplate

• Pforever Seal Ceramic

Disc Valve

• Pforever Warranty®

• IAPMO Certified

• CSA B125 Certified

• ASME A112.18.1

• Cal Green Compliant

• CEC Compliant

• NSF 61/9 Annex G (Low lead)

• EPA WaterSense Certification 1.2 gpm, 4.5 L/Min

• ADA Compliant-ANSI A117.1 (Lever handles only)

Pfister products are designed and manufactured in compliance with the following standards and codes:

10-15/16 [277.8]

1-31/32

[49.8] MAX DECK

THICKNESS

1-13/16 [45.8]

4-5/8 [117.1]

6-27/32 [173.5]

4-5/32 [105.5]

1-1/2 [38.1]

5-3/4 [146.4]

29/32 [22.9]

[101.6]

2-1/16 [52.1]

11/32 [8.4]

10-15/16 [277.8]

1-31/32

[49.8] MAX DECK

THICKNESS

1-13/16 [45.8]

4-5/8 [117.1]

6-27/32 [173.5]

4-5/32 [105.5]

1-1/2 [38.1]

5-3/4 [146.4]

29/32 [22.9]

[101.6]

2-1/16 [52.1]

11/32 [8.4]

Ø1 Min to Ø1-1/2 Max. Deck Hole Openings

SS-LF042-VNXX

Push & Seal™

11781-00 July 7, 2016 Copyright © 2016, Pfister Inc.

1-800-PFAUCET (732-8238) • pfisterfaucets.com/support

Optional Deck and Putty Plate

FX-2

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

FX-3 8" WIDESPREAD FAUCET

Specifications

Features Code Compliance

Venturi™ 8”-20” Widespread Faucet

LF-049-VNGS Finish(GS) q LF-049-VNKK Finish(KK) q LF-049-VNYY Finish(YY) q

LF-049-VNBB Finish(BB) q LF-049-VNCC Finish(CC) q

• Pfast Connect Supply Lines

• Pforever Seal

• Push & Seal™ Pop-Up

• 1.2 GPM Flow Rate

• Adjustable 3-Hole Installation

• All Metal Construction

• Color Coded Connections

• High Arc Spout

• Fixed Hubs

• Mounting Hardware Included

• TiteSeal™

• PVD Finish (KK Finish Only)

• Spot Defense Finish Resists Spots and Fingerprints (GS Finish Only)

• Quick Install Tool Included

• Pfast Connect Supply Lines

• Push & Seal™ Pop-Up

• Pforever Seal Ceramic

Disc Valves

• Pforever Warranty®

• IAPMO Certified

• CSA B125 Certified

• ASME A112.18.1

• NSF 61/9 Annex G (Low lead)

• Cal Green Compliant

• CEC Compliant

• EPA WaterSense Certification 1.2 gpm, 4.5L/Min

• ADA Compliant-ANSI A117.1 (Lever handles only)

Pfister products are designed and manufactured in compliance with the following standards and codes:

2-21/32 [67.5]

3-21/32 [92.5]

1-15/16 [49.1]

2-1/16 [52.2]

2 [50.8]

MAX DECK

THICKNESS

6-7/32 [157.9]

1-3/16 [29.9]

[381.3]

4-31/32 [126.6]

4-5/32 [105.5]

4-5/32 [105.3]

2-3/16 [55.7]

Copyright © 2016, Pfister Inc.

1-800-PFAUCET (732-8238) • pfisterfaucets.com/support

Ø1-1/4 Min to Ø1-1/2 Max. Deck Hole Openings

SS-LF049-VNXX

Push & Seal™

10358-27 March 7, 2017

FX-3

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

FX-4 FLOOR MOUNT TUB FILLER

Specification Sheet:

Bathtub Filler

Model No.

TF0047

Connection Standard 1/2" Hose Material Brass

Dimensions(in.) 45.47 (H) x 6.5 (W) x 12.2(D) Finish Brush Nickel

Flow Rate (GPM) 4.1 40.2" Height to Spout

Lever Installation Type Floor Mount

Handshower Hose Length 60"

Certification US & Canada cUPC Certified

Warranty 1-Year Limited Parts Warranty

Handle Type

Handshower Yes www.akdyusa.com E-Mail：help@akdyusa.com Tell：(888) 808-0450

FX-4

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

FX-5 TUB SHOWER FAUCET

• Advanced spray engine provides three spray options: powerful massage, intense drenching, or wide coverage.

• Wide coverage spray produces an encompassing spray for everyday use.

• Intense drenching spray delivers a forceful spray ideal for rinsing soap from hair.

• Powerful massage is a focused stream for massaging sore muscles or for use as a utility spray.

• MasterClean™ sprayface features an easy-to-clean surface that withstands mineral buildup.

• Single-lever handle allows for simultaneous on/off activation and temperature control.

• Premium KOHLER finishes with ScratchShield® technology withstands even the toughest daily use.

• Rite-Temp® pressure-balancing technology maintains water temperature within +/- 3 degrees Fahrenheit for anti-scalding protection and precise temperature control.

Codes/Standards• Package includes: showerhead, showerarm and flange, valve trim plate, diverter spout with 1/2" NPT or slip-fit connection and Rite-Temp® valve with 1/2" connections.

ASME A112.18.1/CSA B125.1

ASSE 1016/ASME A112.1016/CSA B125.16

Material DOE - Energy Policy Act 1992 EPA WaterSense®• Constructed with premium materials for durability and reliability. California Energy Commission (CEC)

Adapters, Rough-in and Extension Kits KOHLER® Faucet Lifetime Limited Warranty

K-10350-NA

See website for detailed warranty information.

Available Colors/Finishes Color tiles intended for reference only.

DescriptionCodeColor

Polished ChromeCP

Vibrant® Brushed NickelBN

Matte BlackBL

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current Specification Sheet, go to www.kohler.com.

3-25-2019 03:37 - US

Katun®

Bath / Shower Set K-R78040-4E

FX-5

K-2971-KS,

NotesTechnical Information For use with automatic compensating valves rated at 1.08 gal/min (4.1 l/min) or less.

All product dimensions are nominal.

Shower Valve:

Install this product according to the installation instructions.5 gal/min (18.9 l/min)Flow rate - Max:

45 psi (3.1 bar)Pressure - Max:

20 psi (1.4 bar)Min. pressure IN:

Showerhead/Body Spray:

1.8 gal/min (6.8 l/min)Rated maximum flow:

80 psi (5.5 bar)Pressure:

1-800-4KOHLER (1-800-456-4537)

Kohler Co. reserves the right to make revisions without notice to product specifications.

For the most current Specification Sheet, go to www.kohler.com.

3-25-2019 03:37 - US

Katun®

Bath / Shower Set K-R78040-4E

FX-5

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

BT-1 60" RIGHT DRAIN BATHTUB

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

BT-2 60" LEFT DRAIN BATHTUB

ALOHA PORCELAIN ENAMEL

60” X 30” X 14 1/4”BATHTUB

STANDARD BACK DESIGN

ALOHA 5’ Bathtub 60” x 30” x 14 1/4” Standard Outlet 011-2364 RH Drain, slip resistant 011-2365 LH Drain, slip resistant

R

1400 Park Street • P.O. Box 18010 • Evansville, IN 47719-1010 • (812) 423-5401 • Fax (812) 429-2254 • www.bootz.com • webmaster@bootz.com

All Dimensions +\- 1/8” unless otherwise noted.

Dimensions shown are for reference.

Actual dimensions may vary slightly and should be checked prior to installation

SS 5/14

Standard Features:

“The affordable alternative to cast iron”

Full length sound deadening pad Slip resistant bottom

Set it and level it

Made in the USA

Complies with:

All fixtures are compatible or comply with

ANSI, ASME, CSA, WW-P 541, HUD-FHA-

VA, LEED and the “Buy America Act” where applicable when installed accordingly.

#104768 Bootz SpecSheets.indd 28 11/11/16 11:34 AM

BT-1 & BT-2

R

1400 Park Street • P.O. Box 18010 • Evansville, IN 47719-1010 • (812) 423-5401 • Fax (812) 429-2254 • www.bootz.com • webmaster@bootz.com

ALOHA PORCELAIN ENAMEL

60” X 30” X 14 1/4”BATHTUB

STANDARD BACK DESIGN

011-2364 RH DRAIN, SLIP RESISTANT

011-2365 LH DRAIN, SLIP RESISTANT

DESCRIPTION:

The Aloha is a 60” x 30” x 14 1/4”bathtub – the industries #1 selling porcelain enamel bathtub is full length bath offering exceptional performance and roominess for a recess application. The Aloha has a traditional design with a standard “straight” back support. Construction is a one piece heavy gauge seamless steel with an acid resistant porcelain enamel finish. The Aloha weighs 67 lbs., easy to install into a bathtub alcove - “just set it and level it”. Free standing on a full length support pad that offers added strength and sound deadening. This product is compatible or complies with ASME A112.19.1/ CSA B45.2 (Standard for Enameled Steel Plumbing Fixtures), ADA (American Disabilities Act), ASTM F 462 (Safety Specification for Slip Resistant Bathing Facilities), WW-P 541 (U.S. Military Federal Specification), HUD-FHA-VA, LEED, and the Buy American Act, as applicable when installed accordingly. Available in white, bone and biscuit colors with a right and left drain. Made in the USA.

Weight: 67 lbs

#104768 Bootz SpecSheets.indd 27 11/11/16 11:33 AM

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

PRODUCT TECHNICAL SHEETS

BT-3 60" ALCOVE BATHTUB + DRAIN

BT-5 60" ALCOVE BATHTUB +

DRAIN

Technical Information

Fixture*:

Bathing well:

Basin area, bottom

45-5/16″ (1151 mm) x 25-9/16″ (649 mm)

Basin area, top

52-9/16″ (1335 mm) x 28-1/16″ (713 mm)

Weight 70 lbs (32 kg) To overflow:

Water depth 12-11/16″ (322 mm) Capacity 55.6 gal (210.5 L) *Approximate measurements for comparison only.

Installation Notes Install this product according to the installation guide.

Floor support under the bath must provide for a minimum of 45 lbs/square foot (219.7 kg/square meter) loading.

Integral Flange Detail

1-1/4" (32 mm)

3/8" (10 mm) R.

1-1/4" (32 mm)

No change in measurements if connected with drain illustrated. (K-7213)

17" (432 mm)

18-1/4" (464 mm)

2-1/2" (64 mm)

1/2" (13 mm)

3" (76 mm)

2-7/8" (73 mm)

30" (762 mm)

9-3/4" (248 mm)

2-5/16" (59 mm)

60" (1524 mm)

16-7/8" (429 mm)

36" (914 mm)

1-1/2" Bath Drain

Product Diagram

EXPANSETM

EXPANSETM CURVED APRON BATH

1167628-4-A

BT-3

• Acrylic

• Integral tile flange

• Curved integral apron

• Textured bottom surface

• 55.6 gallon (210.5 L) capacity

• Install footprint: 36″ (914 mm) width at center of apron

• 60″ (1524 mm) x 30 (762 mm) x 17″ (432 mm)

Codes/Standards Applicable Specified model meets or exceeds the following:

• ASME A112.19.7

• ANSI Z124.1.2

• CSA B45.0

• CSA B45.5

• ASTM E162

• ASTM E662

CURVED APRON BATH

K-1118

Colors/Finishes

• 0: White

• Other: Refer to Price Book for additional colors/finishes

Accessories

• CP: Polished Chrome

• Other: Refer to Price Book for additional colors/finishes

Specified Model

Model Description Colors/Finishes K-1118-LA Curved apron bath – left drain (shown) ❑ 0 ❑ Other_____ K-1118-RA Curved apron bath – right drain ❑ 0 ❑ Other_____

Recommended Accessories K-7213 Clearflo cable bath drain with PVC tubing OR ❑ CP ❑ Other_____ K-7214 Clearflo cable bath drain, less PVC tubing OR ❑ CP ❑ Other_____ K-7259 Clearflo brass Toe-tap bath drain ❑ CP ❑ Other_____

Product Specification The curved apron bath shall be made of acrylic. Bath shall be 60″ (1524 mm) in length, 30″ (762 mm) in width, and 17″ (432

mm) in height. Bath shall feature a curved integral apron, integral tile flange, and textured bottom surface. Bath shall have install footprint of 36″ (914 mm) width at center of apron. Bath shall have a capacity of 55.6 gallons (210.5 L). Bath shall be Kohler Model K-1118-____-____.

EXPANSETM

1167628-4-A

USA/Canada: 1-800-4KOHLER (1-800-456-4537) www.kohler.com

• For baths 17″ (43.2 cm) to 22″ (55.9 cm) deep from the center of the bath overflow outlet to the center of the bath drain outlet

• 27″ (68.6 cm) length cable

• Adjustable rotating connection for easy installation

• Metal construction control handle and stopper

• Includes PVC tee

Codes/Standards Applicable Specified model meets or exceeds the following:

• ASME A112.18.2

• ASME A112.18.1/CSA B125.1

• IAPMO/UPC

CABLE DRAIN

K-7213

ALSO K-7214

Colors/Finishes

• CP: Polished Chrome

• Other: Refer to Price Book for additional colors/finishes

Specified Model:

Model Description Colors/Finishes K-7213 Cable drain with PVC tubing ❑ CP ❑ Other_____ K-7214 Cable drain without PVC tubing ❑ CP ❑ Other_____

PRODUCT SPECIFICATION

Cable drain shall be for baths 17″ (43.2 cm) to 22″ (55.9 cm) deep from the center of the bath overflow to the center of the bath drain outlet. Product shall feature a 27″ (68.6 cm) length cable. Product shall feature a metal constructed control handle and stopper. Product shall feature an adjustable rotating connection for easy installation. Product shall include a PVC tee. Product shall be Kohler Model K-____-____.

CLEARFLO

1054250-4-B

USA: 1-800-4-KOHLER

Canada: 1-800-964-5590 kohler.com

Installation Notes Install this product according to the installation guide.

The combined length of the PVC tubing (noted as L1 and L2 in the Product Diagram) must be equal to or less than 25″ (63.5 cm).

2-9/16" (6.5 cm)

L2

1-3/8" (3.5 cm)

1-1/2" PVC Tee

L1

NOTE: L1 + L2 must be equal to or less than 25" (63.5 cm) in length.

Product Diagram

CLEARFLO

CLEARFLO CABLE DRAIN

1054250-4-B

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

BT-4 PEDESTAL BATHTUB

BT-4

Ft. Buchanan, Guaynabo, Puerto Rico Project No. W91278-18-D-0003

T-1 - DUAL FLUSH TOLIET

SKU: 635-675 (white)

© 2016 Glacier Bay Rev. June 23, 2016 9:39 AM

FEATURES

• High-efficiency dual flush volume of 1.6 GPF (solids) or

1.1 GPF (liquids)

• Meets HET rebate standards - high rebate dollars

• QuickConnect™ Installation System

• Saves up to 15,000 gallons of water per year

• Sleek one-piece design

• 12” rough-in

• 2” fully glazed trapway

• Chrome plated top mount flush button

• Limited Lifetime Warranty

OTHER COLORS/FINISHES:

BISCUIT (SKU:569-927)

BLACK (SKU:569-930)

BONE (SKU:700-232)

INCLUDES:

8 Included U Not Included

FLUSH

POWER

CHAIR

HEIGHT

ELONGATED

BOWL

10 E

8 8

8 8

8 U

1.1/1.6 GPF

ONE-PIECE DUAL FLUSH ELONGATED

All-In-One Toilet

T-1

INSTALLA…